Download from Www.Somanuals.com. All Manuals Search And Download.
SET-UP AND SAFETY
___________________________
To ensure that this high quality, easy-to-use device gives you lasting
entertainment and enjoyment, please note the following information.
C
°C
2h
This device designed to receive and play back video and
audio signals. Any other use is expressly prohibited.
-
T
-
T
When setting up the device, make sure it is in a horizontal
position and that the mains socket is easily accessible.
If the device is subject to a sudden change in temperature, for
example when brought in from the cold to a warm room,
let it stand for at least two hours before you connect it to the mains
supply.
-
T
Do not expose the device to any moisture.
The device is designed for use in dry rooms. If you do use it
outdoors, please ensure that it is protected from moisture, such as
rain or splashing water. Do not place any vessels such as vases on
the device. These may be knocked over and spill fluid on
the electrical components, thus presenting a safety risk.
g im Balkan
-
T
Do not place the device close to heating units or in direct
sunlight, as this will impair cooling. Place the device on a
hard, level surface. Do not lay any objects such as magazines on
the device. When placed in a cabinet, make sure there is a
minimum space of 10 cm around it.
-
T
Thunderstorms are a danger to all electrical devices. Even if the
device is switched off, it can be damaged by a lightning strike
to the mains or the antenna.
Always disconnect the mains and antenna plugs during a storm.
Never open the device casing under any circumstances.
Warranty claims are excluded for damage resulting from improper
handling.
DO NOT REMOVE COVER
HAZARD LIVE PARTS
RS 232
220-240
50/60 Hz 10
V
INPUT TER.
F/UHF
OUTPUT TER.
DIGITAL AUDIO
OUT
E
U
R
O
AV
2
V
C
R
E
U
R
O
AV
1
TV
-
W
G.RP 42
Serial Number
DIGITAL TERRESTRIAL RECEIVER
DTR 52
5
V
1
1
max. 30 mA
Environmental note
If you do not intend to use the device for some time (for example
at night), switch it to Power Off by pressing Power button of
the product. This saves electricity.
Note: This page is only for the purpose of safety notice. The
drawings on this page may be different from the actual product.
Download from Www.Somanuals.com. All Manuals Search And Download.
INFORMATION _________________________
General information on laser devices
Your system is a CLASS 1 LASER PRODUCT. This means that the laser is designed in such a way as to
ensure that the maximum permissible emission value cannot be exceeded under any circumstances.
CLASS 1
LASER PRODUCT
Caution:
This device emits laser radiation. Because of the danger of eye injuries, the unit may only be opened
or serviced by trained personnel.
If settings other than those specified here are employed or other procedures are carried out, this may
lead to dangerous radiation exposure.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety information
__________________________________________________
Note:
Before connecting the AC power cord to the DC adapter outlet, make sure
that the voltage designation of the DC adapter corresponds to the local
electrical supply. If you are unsure about your power supply, please ask
the local power company.
Caution:
To avoid electric shock, never touch the inside of the LCD TV/Monitor. Only
qualified technicians should open the case of the LCD TV/Monitor.
Warning:
Do not defeat the safety purpose of grounding-type. A grounding type plug
has two blades and a third grounding pin. The third pin is provided for your
safety. If the plug does not fit, ask the electrician to replace the obsolete
outlet. Do not modify the plug!
To reduce the risk of fire or electric shock, and annoying interference, use
the recommended accessories only.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
________________________________________________________
Please read the below precautions carefully before operating the unit.
Power cord protection:
1. Never use your LCD TV/Monitor if the power cord has been damaged.
Do not put anything on the power cord, and keep the power cord away
from where people can easily trip over it.
2. Be sure to hold the plug , do not pull the cord when disconnecting the
LCD TV/Monitor from an electric socket.
3. Locate your LCD TV/Monitor near an easy accessible AC outlet.
Placement:
1. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus.
2. An appliance and a cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
appliance and cart combination to overturn.
3. Never placing the LCD TV/Monitor in areas under direct sun-light, with
high temperature or with high humidity or high level of dust which may
cause damages on the internal parts of the LCD TV/Monitor.
4. Place the LCD TV/Monitor on a solid surface and treat it carefully. The
screen is made of thin glass with a plastic front surface and can be
damaged by dropping, hitting or scratching.
Non-use periods:
Unplug the LCD TV/Monitor when it will no be used for a long period.
Foreign objects:
Never insert anything metallic into the cabinet openings of the TV/Monitor.
Doing so may cause the danger of electric shock.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Keep away from water/magnetic fields:
1. Do not expose the LCD TV/Monitor to rain or use it near water source.
If the LCD TV/Monitor got wet, unplug it and contact an authorized
dealer immediately.
2. Do not clean the front panel with Ketone-type materials, ethyl alcohol,
toluene, acid, methyl, or chloride since they may cause damage on
panel.
3. Keep the unit away from flower vases, tubs, sinks etc. if liquids spill
into the unit, serious damage will occur.
4. Do not place magnetic objects close to the LCD TV/Monitor.
Stacking:
Opening in the LCD TV/monitor cabinet are provided for ventilation. To
prevent overheating, these openings should not be blocked or covered.
Never use the unit on a bed, sofa, rug, or other uneven surfaces. Doing so
may block the ventilation openings in the bottom of the unit. If you place the
LCD TV/Monitor in a bookcase or some other enclosed place, please make
sure to provide adequate space for ventilation.
Servicing:
1. If the LCD TV/Monitor does not operate normally – In particular, if there
are any unusual sounds or smells coming from the unit – just unplug it
immediately and contact an authorized dealer or service center.
2. Unplug the LCD TV/Monitor from the AC outlet before any service.
3. Make sure the service technician uses authorized replacement parts or
their equivalents. Unauthorized parts any cause fire, electrical shock,
or other hazard.
4. Following any service or repair, be sure the service technician
performs safety checks to certify that the TFT LCD TV/Monitor is in
safe operating order.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
____________________________________________
Please make sure that the following items are included with your LCD
TV/Monitor. If any item is missing, please contact your dealer.
TFT LCD TV/ Monitor
Remote control
Operation manual
DC adapter
RCA cable
Power cord
Car Cord
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of content
I.
View of the TV/Monitor ---------------------------------------------------- 6
II. Remote control reference guide --------------------------------------------- 7
(1) Remote control function --------------------------------------------- 7
(2) Remote control battery installation and cautions ------------- 8
III. Installation and connection ----------------------------------------------- 9
IV. TV/Monitor screen operation --------------------------------------------- 10
(1) Basic operation -------------------------------------------------------- 10
(2) View of the TV plays -------------------------------------------------- 11
(3) View of the AV signal sources -------------------------------------- 11
(4) View of the TELETEXT program ------------------------------- 12
(Optional, if the unit has this function.)
(5) PC screen --------------------------------------------------------------- 12
V. Menu setting and adjustment -------------------------------------------12
(1) Video mode setting --------------------------------------------------- 12
(2) Audio mode setting --------------------------------------------------- 15
(3) Time mode setting ---------------------------------------------------- 16
(4) Tuner/Channel mode setting --------------------------------------- 17
(5) Options mode setting ------------------------------------------------- 19
VI. DVD player operation ------------------------------------------------------- 21
VII. Other Operation -------------------------------------------------------------- 28
VIII. Trouble shooting ------------------------------------------------------------- 28
IX. Notes ---------------------------------------------------------------------------- 30
X. Maintenance -------------------------------------------------------------------------- 31
XI. Specification ------------------------------------------------------------------- 32
XII. Display modes ---------------------------------------------------------------- 33
5
Download from Www.Somanuals.com. All Manuals Search And Download.
I. View of the monitor
Side view
Front view
Back view
1. Remote sensor
12. VGA jack
2. Power indication light
13. YUV jack
3. Headphone jack
14. S-video jack
4. CH+/up direction button
5. CH-/down direction button
6. VOL up/RIGHT direction button
7. VOL down/LEFT direction button
8. Menu button
15. Video in jack
16. Audio in (left) jack
17. Audio in (r/mono) jack
18. TVRF jack
19. DVD Play/Pause button
20. DVD Stop playing button
21. DVD open/close button
22. DVD disc slot in
9. TV/AV button (Function switch button)
10. Power button
11. DC input jack/ Car Cord input jack
6
Download from Www.Somanuals.com. All Manuals Search And Download.
II. Remote control reference guide
(1) Remote control function
1. DVD open/close
2. Video out mode button
3. SLEEP button
4. 0-9 Numerical button
5. Program play button
6. Volume down button
7. Unit system menu button
8. Display status message button
9. DVD stop button
10. DVD ENTER/PLAY button
11. DVD fast rewind button
12. DVD fast forward button
13. DVD MENU display button
14. Direction button (Up)
15. Direction button (Left)
16. DVD system setup/enter button
17. ANGLE button
18. Direction button (Down)
19. RANDOM play button
20. SUBTITLE function button
21. TELETEXT buttons
22. Key lock button
23. ZOOM function button
24. Search disc play mode
25. TITLE/PBC button
33. CH- button
34. Audio effect button
35. Volume up button
36. CH+ button
26. SLOW PLAY button
27. Direction button (Right)
28. REPEAT A-B button
29. REPEAT button
37. TV/DVD switch button
38. -/- -(+10) button
39. TV/AV function switch button
40. RECALL button
41. MUTE button
30. DVD skip backward
31. DVD skip forward
32. DVD PAUSE/STEP button
42. STANDBY button
7
Download from Www.Somanuals.com. All Manuals Search And Download.
● TELETEXT BUTTONS
(If TV has teletext function. You may enjoy it by using these buttons)
Name
Function
Name
Function
To select TXT/TV mode
To show the sub page
Enter into TXT list mode
Keep the page display
Menu display
Display the hidden
information
INDEX
Screen zooming
Page display or cancel
RED
Display red screen
GREEN
BLUE
Display green screen
Display blue screen
YELLOW
Display yellow screen
(2) Remote control battery installation and cautions
Replace battery by following the below steps:
Requires one pair of AAA batteries.
1. Open the battery cover as shown below:
2. Install the battery into the battery tray.
3. Close the battery cover
Caution:
1. Keep the battery out of children’s reach.
2. Don’t attempt to recharge, short-circuit, disassemble, heat or throw the
8
Download from Www.Somanuals.com. All Manuals Search And Download.
batteries into the fire.
3. Always replace both batteries at the same time. Never mix new and old
batteries or batteries of a different type.
4. If you don’t intend to use the remote controller for an extended period,
remove the batteries to prevent possible leakage and corrosion.
Notes:
1. Do not drop, apply shock or step on the remote control.
2. Do not spill water on the remote control.
3. Do not use the remote control for other equipments at the same time
4. If the TV does not operate even when operating the remote control
from a close range, you need to replace the batteries.
Refer to the label on the back of the remote control for directions for
replacing batteries.
III. Installation and connection
Connect the LCD TV/monitor
1. Connect the TVRF source with the antenna port. TVRF signal
including: Receiving antenna /satellite TV/CATV net. You can use 75
Ω coaxial cable to connect the outdoor antenna.
Outdoor Antenna Connection:
Use 75Ωcoaxial cable plug or 300-75Ωimpedance converter to plug
in antenna input terminal on the rear of the cabinet.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
VHF antenna
UHF antenna
75ΩCo-axis cable
Input terminal of
antenna
Mixer
Co-axis antenna
plug
Antenna in jack
75ΩCo-axis cable
2. Connect the audio sources (Including DVD, VCDR, CAMCORDER
and PC) to the proper AUDIO input jacks ‘L’ and ‘R’.
3. Connect the video source to the VIDEO jack by RCA cable.
4. If the video source has a YUV output jack, you can connect the signal
to the monitor by the YUV cable.
5. Connect the video source to the S-VIDEO input jack of the monitor by
the S-video cable (Pretended the video source has S-video output
jack).
6. Insert the AC power to the DC adapter, then connect 12V input jack of
the monitor to it’s DV output jack.
7. When use as computer screen, connect the PC to the VGA jack of the
monitor by the relevant cable.
IV. TV/Monitor screen operation
(1) Basic operation
1. Press the POWER button on the unit or the STANDBY button on the
remote control to switch on the power. The indication light will be in
blue color . Press the POWER or STANDBY button again to switch off
the power, and the light will be in red color.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. The Picture setup, Sound setup, Previous channel can be memorized
before you switch off the TV/Monitor. The TV/Monitor will re-start under
the previous state when you switch on it again.
3. If you unplug the power cord to cut off the power supply completely, all
previous setting will be lost.
4. Press the V - or V + button to adjust the volume output. Press the V -
button repeatedly to decrease the volume; press the V + button
repeatedly to increase the volume from 0 to 100.
5. Press the SLEEP button to display the preset time on the screen.
(2) View the TV plays.
1. Press the TV/AV button on the unit or the remote control to select the
TV function mode. The TV will appear the initial channel ‘1’ on the top
right corner when the function is on. Press the P- or P+ button to select
the previous or next channels; or press the 0-9 buttons to enter a
channel number directly, or press the -/-- button until the screen
display ‘--’ or ‘---’, then use the 0-9 numerical buttons to enter a
channel number from 10 to 249.
2. Press the RECALL button on the remote control to select from the
present channel and the previous channel.
3. Press the PP button to select video out mode from the below 4 types
User
Standard
Mild
Dynamic
4. Press the MUTE button to cut off the sound output, then the screen will
show “ “ mark , press this button again to resume sound output..
5. Press the DISPLAY button to display the preset channel mode.
(3) View the AV signal sources (DVD/VCR/CAMCORDER)
Press the TV/AV button on the remote control, there will be a menu
displayed on the screen as followed:
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the suitable input to pickup the AV signal.
Press P+ or P- button to select source, then press
V + button to confirm your selection. Or press DVD
Button on the remote control to select DVD source
directly.
Input Source
TV
Video
S-Video
VGA
YUV
(4) View the TELETEXT program
(Optional. If TV has this function.)
DVD
1. Press the TV/AV button to select the TV mode. Then press the P- or
P+ button on the remote control to select TV channel in order to pick
up the picture signal of TELETEXT.
2. Press
can allow you:
button to enter into picture showing mode. The button
Enter into the
Exit
picture showing
3. Press the P- or P+ button to select the previous page or the next page;
use the 0-9 numerical buttons and the -/- - (+10)button to enter into a
numerous page.
4. Refer to the chapter of ‘Remote control reference guide’ to grasp other
functions of the TELETEXT buttons.
(5) PC screen
Press the TV/AV button to select the VGA input (TV into VGA) mode. The
will be a ‘VGA’ mark appears on the right of the top corner of the monitor.
The unit has a VGA jack for a normal computer. Connect the monitor with a
PC by this jack and the unit can be used as the monitor of the PC.
V. Menu setting and adjustment
1. VIDEO MODE SETTING
Press the MENU button on the remote control, there will be a menu
displayed on the screen as below:
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Video
Picture Mode
Brightness
: Standard
50
60
0
Contrast
Hue
Saturation
Sharpness
Color Temp.
Advanced
50
50
: Standard
Move
Select
Exit
On this menu, the Video setting icon of
is in blue color. Use the V+
button firstly, the cursor will be on the line of “Picture Mode: Standard”.
And then, press the V+ or V - button repeatedly to select the video mode
from Standard, Mild, Dynamic, or User.
After select the video user mode, you can use the P- or P+ button to select
the item of Brightness, Contrast, Hue, Saturation, Sharpness, and then use
the V- or V+ button to adjust the Value of each item for each Video Mode
respectively.
When the cursor is on the line of “Color Temp. ：Standard”, you can press
the V+ or V- button repeatedly to select from Standard, Warm, or Cool.
PC MODE SETTING
Under PC mode, after connect VGA cable, press the MENU button on the
remote control, then select video setting. Use P+/P- to select the
“Advanced” menu, press the V+ button, the below will display on the
screen:
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Image
Auto Config.
Image Position
Phase:
30
Clock:
1344
Move
Select
Exit
1.The cursor will on the line of “Auto Config”, press the V+ button, the
following will be displayed on the screen, then select Yes to enter into
auto configuration as followed:
Auto Config.
Auto Config. :
Yes
No
Move
Select
Exit
2. When the cursor is on the line of “Image Position”, press V+ to enter to
set the image in the central position, as followed:
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Position
Move
Select
Exit
After the setting, press the MENU button to return to the root menu or exit
the setting
2. AUDIO MODE SETTING
Press the MENU button on the remote control, and then press the P- button
to select the Audio setting, the Menu will be shown as below:
Audio
Base
50
50
0
Treble
Balance
Move
Select
Exit
On this menu, the Audio setting icon of
is in blue color. Press V+
firstly to enter into the “Base” menu, press the P+ or P- button repeatedly to
15
Download from Www.Somanuals.com. All Manuals Search And Download.
select the sound mode from Base, Treble, Balance.
After select the sound mode, you can use the V- or V+ button to adjust the
Value of each item from 0 to 100 or Balance from -50 to 50 for each sound
Mode.
After the setting, press the MENU button to return to the root menu or exit
the setting menu.
3. TIME MODE SETTING
Press the MENU button on the remote control to show to setting menu, and
then press the P- button to select the Time setting icon, and the menu will
be shown on the screen as below:
Time
Clock enable
Set Time
: Off
01:20
00:00
00:00
00:00
TurnOff Time
TurnOn Time
Switch Time
Switch Channel
TurnOn Channel
Move
:
:
1
0
Select
Exit
On this menu, the Time setting icon of
is in blue color. Press the V+
button for the first time to remove the cursor on the line of “Clock enable
On”, you can select On or Off by press the V+ or V- button repeatedly.
After selected “Clock enable: On”, use the P- or P+ button to select the item
of Set Time, TurnOff Time, TurnOn Time, Switch Time, Switch Channel or
TurnOn Channel, and then, input the accordingly value to set each item.
After the setting, press the MENU button to return to the root menu or exit
the setting menu.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4. TUNER/CHANNEL MODE SETTING (FOR TV MODE ONLY)
Press the MENU button firstly to display the menu, and then use the P-
button to select the Tuner/Channel setting icon, the following menu will
display in the screen:
Tuner/Channel
Channel No.
Color System
Audio System
Skip
: 1
:AUTO
:DK
:Off
Auto Search
Manual Install
Channel Swap
Move
Select
Exit
As shown on the menu, the Tuner/Channel icon
is in blue color.
Press V+ button, the cursor will on the line of “Channel No. 1”. Use the P-
/P+ and V-/V+ buttons to select and set each item.
(1) Channel No. : Select “Channel No.”, input the Channel No. to search
the channel you require.
(2) Color System: Select “Color System”, press V-/V+ buttons repeatedly,
it will select at AUTO or PAL.
(3) Audio System: Select “Audio System”, press V-/V+ buttons
repeatedly, it will select at DK, I or BG.
(4) Skip: Select “Skip”, after setting to “On”, the channel will not be
selected by Channel Up/Down keys.
(5) Auto Search
Select the item of “Auto Search” , and then press the V+ / V- button:
17
Download from Www.Somanuals.com. All Manuals Search And Download.
CH NO:9
Band: VHF-L
Auto search
-
+
FREQ: 175.15 MHz
As shown on the menu, the TV will automatically search stations. When
searching, press the MENU button to cancel searching. After the searching,
the TV will begin to play the station 1.
(6) Manual Install
Select the “Manu Install”, and then press the V+ /V- button
Manual Install
Manual Search
Fine Tune
Band
0
: VHF-L
FREQ 77.25 MHz
Move
Select
Exit
As shown on the menu, the channel will be displayed on the screen. Press
the V-/V+ button repeatedly until you search a required station. Press the
MENU button to save the station.
(7) Channel Swap
Select the “Channel Swap”, and then press the V+ button, the screen will
display:
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuner/Channel
Swap From
Swap To
6
1
Perform Swap
Move
Select
Exit
On the menu, the words “Swap From” indicate the current station and 6 is
the station number; “Swap To” means the destination station and 1 is the
station number. The TV is playing the current station (6). Press P- button to
keep the cursor on the line of “Swap To”, you can enter into a station
number from 1-254 by the digit buttons 0-9 and the -/-- button as the
appointed station number (***) for replacing the current station number.
After entered into the number, press P- again, the cursor will on the line of
“Perform Swap”, then press V+ button, the TV will play the programs of the
appointed station (***).
Press the MENU button to exit from this menu.
5. OPTIONS MODE SETTING
Press the MENU button on the remote control to display the menu, and
then press the P- button to select the option setting, and the menu will be
shown on the screen as below:
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
Language
Reset
:Off
Blue Screen
OSD Timeout
Keypad Lock
Menu Background
:On
:10 Seconds
:OFF
:Transparent
Move
Select
Exit
Press P-/P+ or V+/V- to select or set each item, select “Language” firstly,
press V+ or V- button, it can be set at English, France, German, Spanish,
Portuguese, or Italian, etc.. The “Blue screen” can be set at ON or OFF
mode. “OSD Timeout” can be set at 10, 15, 20, 25, 30 by press the V+ or V-
button repeatedly.
Select the “Keypad Lock”, when set at OFF, child lock is unworkable ; when
it is ON, it could lock the present, press LOCK button of remote control to
cancel the child lock. You can also press LOCK button directly to set or
cancel the child lock.
The “Menu Background” can be set at Transparent or Opaque.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
VI. DVD PLAYER OPERATION
a. Basic play
1. Press the TV/AV button on the unit or the remote control to select the
DVD function mode.
2. Insert a disc into the slot of DVD player and it will be read
automatically.
3. Press ”OPEN/CLOSE” button of remote control or the
button on
the unit ,the disc will be ejected automatically
HOW TO SELECT THE TRACK
If you want to play the second track or chapter, please press the number
button “2” directly. And press ENTER/PLAY button to play.
HOW TO PAUSE PLAYBACK (STILL PLAYBACK)
Press the PAUSE/STEP button one time only during playback .
Press the ENTER/PLAY button to resume normal playback.
HOW TO REMOVE THE DISC
Press the OPEN/CLOSE button on the remote control.
Wait until the disc is completely ejected before removing any discs.
HOW TO STOP PLAYBACK
If press the STOP button once, the DVD video player is stopped. At this
point, press the ENTER/PLAY button to re-start the disc from the same
point.
If press the STOP button twice, the disc will stop completely.
FAST FORWARD/ REWIND
Press the ꢀor ꢁ button once, the disc will be played forward or backward.
With each subsequent press, the disc will be played back at 2x, 4x, 8x, 16x
or 32X speed. Press ENTER/PLAY button to return to normal play.
SKIP NEXT/ PREVIOUS
Press the ꢂ or ꢃ/ button to select the next track or the previous track.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
b. SLOW PLAY
Press SLOW PLAY button when playing, you can play the disc at 1/2, 1/4,
1/8, 1/16 of the normal speed. If you want to stop it, you can press
ENTER/PLAY button to play normally again.
c. ZOOM PICTURE
This DVD video player allows you to zoom in/ out a picture as well as shift
the zoom point. Press ZOOM during normal play or slow motion, the DVD
video player magnifies in the center or the picture at 2x, 3x, 4x, 1/2, 1/3, 1/4
of the normal picture. In the ZOOM mode, you can use / /
/
buttons
to move the picture for optimum viewing.
d. REPEAT PLAY
You can use the REPEAT button to repeat the playing under normal
situation.
Press the REPEAT button the first time to repeat playing the present
chapter.
Press the REPEAT button again to repeat playing the present title.
Press the REPEAT button third time to repeat playing the disc.
Press the REPEAT button for the forth time to cancel repeating playing and
return to normal playing.
Note: For different discs, REPEAT button may be have different functions.
REPEAT A SPECIFIC SECTION
You could repeat section by REPEAT A-B button on the remote control.
Firstly press the REPEAT A-B button at the beginning of the section you
want, and press it again at the end of the section. So the unit will repeat to
play from A to B. if you want to cancel the repeat section, please press
REPEAT A-B once again.
Be aware that some discs will not respond to the A-B repeat function.
e. STEP
When the PAUSE/STEP button on the remote control is pressed 1st time,
the picture will become still on the screen. By pressing this button again
and again, the picture will advance picture by picture (frame by frame). To
22
Download from Www.Somanuals.com. All Manuals Search And Download.
return to normal play, press the ENTER/PLAY button. Please note that the
sound is cut off, and the picture becomes silent while playing in this mode.
f. MUTE
Press the MUTE button on the remote control to suppress the sound while
a disc is playing. Press the same button again to resume playing with
sound.
Caution: Do not increase volume of the TV or amplifier when the system is
on MUTE. There are chances of the speakers getting damaged when the
sound is resumed.
g. RANDOM PLAYING (RANDOM)
Press the STOP button firstly, then press the RANDOM button on the
remote control to play the disc in random order of song titles or picture
scenes. Press the STOP button again to cancel random playing.
Note: For different discs, DISPLAY button may be have different functions.
h. POWER ON/OFF
Press the POWER button on the unit to switch the system on or off.
i. DISPLAY
During playback, you can press the DISPLAY button on the remote control
to show the current information available, you will get the information like
Title Elapsed; Title Remain; Ch. Elapsed; Ch. Remain; Display Off and so
on.
Notes:
For different discs, DISPLAY button may be have different functions.
j. PLAYING IN A FAVORITE ORDER
Combine your favorite titles, chapters or tracks and play them in your
favorite order.
HOW TO SET TITLES, CHAPTERS, OR TRACKS IN A FAVORITE ORDER
The program playback function will automatically playback titles, chapters
or tracks in the order preprogrammed.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Insert a disc, press the PROG button, and the menu will display on TV,
as the following:
Program : Chapter
01 --
02 --
03 --
04 --
05 --
PREV
06 --
07 --
08 --
09--
10 --
Exit
11 --
12 --
13 --
14 --
15 --
Start
16 --
17 --
18 --
19 --
20 --
NEXT
2. Input the numbers to select the title and chapter (track) you want, and
pressing the / / / buttons to move the cursor, then input the
next one.
3. By pressing / / / buttons to move the cursor to PLAY, then
press ENTER/PLAY button. The DVD video player starts memory
playback.
NOTE:
z
When the DVD video player is switched off, or if the discs are
removed, the program item will be removed.
z
z
For different discs, PROG button may be have different functions.
If press the STOP button once, the DVD video player is stopped. At
this point, press the ENTER/PLAY button to re-start the disc from
the same point.
z
If press the STOP button twice, program playing will be cancelled.
k. SELECTING THE CAMERA ANGLES SETTING
This DVD video player allows you to select from several different angles.
Press the ANGLE button while playing back a scene recorded with multiple
angles. You may only press the ANGLE button when the angle icon is
flashing on the DVD display. Each time you press the ANGLE button, the
angle will change. Press ENTER/PLAY button to confirm.
NOTE:
z
The angle function will not work on DVD video discs that do not
contain recorded multiple angles.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
z
z
During still playback, you are able to change the camera angle.
However, when you resume to normal playback, the camera
angle changes to the new settings.
The angle icon indicator will illuminate while playing back a title
that contains at least one scene recorded with multiple angles.
l. SELECTING SUBTITLES
This DVD video player allows you to display the subtitles form those
included on the disc, on to your TV screen.
Press the SUBTITLE button during playback, you have the option to select
a preferred subtitle from those included on the DVD/MPEG4 video disc. To
turn off the subtitle function, press the SUBTITLE button during playback
until the subtitles disappears.
NOTE:
z
z
z
With regard to DVD/MPEG4 discs, you may not be able to turn off the
subtitles and they will appear on screen automatically.
As you press the SUBTITLE button, the subtitles may not appear
immediately during some screens.
If the subtitles continue to show on your TV even after the DVD has
been turned off, please refer to the TV’s close caption settings.
m. MP3 OPERATION
1. To play MP3 disc you must view through your television. Insert an MP3
CD, the DVD video player will initialize the disc and the directory
(folder) will be shown in an MP3 MENU on screen.
2
Press the
Then press the
(repeat, shuffle, etc.) Then press the
/
button twice to select and highlight the PLAY MODE.
button each way to select play mode options
button twice then the
/
/
“down” key to select and highlight an MP3 file (song). Press the
ENTER/PLAY button to highlight your list of songs. Press “down” key
to select and highlight.
3. Press the ENTER/PLAY button to play the MP3 file. Press ꢂor
ꢃduring playback to skip the tracks. If you need to return to the main
directory (folder), press STOP.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE:
z
The left column on the TV screen is a list showing the name of
the folder. The right column on the TV screen is a list showing
the name of the song and the sub-folder.
z
z
“MP3” sign in front of a file name indicates that this is a MP3 file.
During MP3 playback, you cannot access to “PLAY MODE” folder
or songs.
n. CUSTOMIZING THE FUCTION SETTINGS
This DVD video player allows you to customize the performance to your
personal preference.
DISPLAYING THE SETUP MENU SCREEN:
The SETUP MENU screen asks you to select a setting category from
GENERAL SETUP, AUDIO SETUP and PASSWORD SETUP. The selected
category will provide you the setting details on the TV screen. Please look
at the followed for more details.
Press SETUP/ENTER button, enter the SETUP MENU. Press / /
/
to select category (highlight), then press SETUP/ENTER button to confirm.
Press SETUP/ENTER button again to normal playback.
Note: Functions and menu may change without notice.
1. GENERAL SETUP
(1)
(2)
(3)
TV Display: you could choose the suitable type for your TV.
Angle Mark: you could choose ON or OFF
OSD language: you could choose your favorite language
displayed on the TV screen.
(4)
(5)
Captions: you could choose ON or OFF
Screen saver: if screen saver on, there will be saver display when
there is no operation for several minutes.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
2. AUDIO SETUP
You could choose AUDIO OUT mode as SPEAKER SETUP, AUDIO
SETUP, could setup to get the best sound as followed:
3. PASSWORD SETUP (PASSWORD: 1369)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
VII.
Other Operation
a.Earphone operation
This unit possesses earphone jack. Connect the earphone with the socket
and adjust the volume to what you want. Once plugged in, the speaker
output will be cut off automatically.
b. AUDIO effect
Press the AUDIO/ST/D/I/II button on the remote control frequently to select
Mono Left, Mono Right , Mix-Mono or Stereo effect. Whether this fuction
should be active or not depend on your disc.
VIII. Trouble shooting
Should the unit no function, please check the system according to this table
to find out the possible problem. If you still can’t solve the problem, please
ensure the product is repaired by qualified service personnel.
a. DVD player
SYMPTOM
CAUSE
Wrong connection or loose
connection;
POSSIBLE CURE
Checking and correcting
all the connections;
No sound
System mute.
Canceling mute.
Disc playing
abnormally
Cleaning or changing disc.
Disc dirty or scratched
Disc not playing Disc placed upside down
Obstacles between remote
Turn the disc right side up.
Clear away obstacles;
Changing battery;
Operating in an effective
distance.
control and the sensor on the
Remote control
unit;
not working
Battery no cell;
Too far away distance.
Can’t operate
system
External interference with the
CPU.
Pull out the plug and insert
again.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
b. TV/Monitor
Symptom
Remedy
1. Check whether the power plug is connected to the power
supply.
No power
2. Pull out the plug and wait for 60 seconds, and then insert
the power plug again and switch on the TV/monitor.
1. Check whether the antenna is connected properly.
2. Adjust to another channel.
No picture
3. Change the length and the contrast setting.
4. Make sure that the AV picture input cable is connected
properly.
1. Increase the volume value.
2. Check whether the TV is at MUTE mode.
3. Make sure that the sound system setting is proper.
4. Ensure the AV audio signal input cable is connected
properly.
No sound
1. Ensure that the equipment is connected properly.
2. Ensure that the AV video signal input is connected
properly.
Color distortion
Pictures/sound are 1. Check whether the equipment is connected properly.
interfered
2. Adjust the antenna if use an outdoor antenna.
1. Make sure that the batteries are installed with correct
polarities.
Remote control no 2. Clean the remote sensor.
function
3. Ensure that there is no foreign object between the
remote control and the sensor.
4. Operate the remote control at a distance not more
than 6 meters from the remote sensor
Screen
glittering Reset the computer and enter into the safety mode, then
under PC mode
select the appropriate screen type by consulting the
operation manual.
Screen traversed
under PC mode
Maybe the phase is not appropriate. Enter into the PC
setting and change to correct level.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
IX. Notes
(1) Please read these operating instructions carefully before you
operate this unit.
(2) When you want to cut off the electricity supply of the whole unit’s
power, please press the POWER button on the unit. And take out
the plug from wall outlet.
(3) Don’t press any button if you are not using the unit. Set the POWER
button to “OFF”, and take out the battery from remote control before
long time non usage.
(4) Be cautious of the safe mark .
(5) Repairs are to be referred to qualified service personnel. Don’t take
apart it by yourself.
(6) Because of a sudden change in temperature or humidity, or when
warm air comes into contact with any cold parts in the unit,
condensation may form. When condensation forms inside, the unit
may not function well. Once condensation disappears, the unit will
return to normal functioning. Placing the unit in a warm room will
help to dry up condensation. This should take 1 to 2 hours,
depending on environmental conditions. As condensation may also
appear on the disc, it should be wiped from inside towards the outer
side using a dry cloth.
(7) It is dangerous to use warped or broken discs since lasers rotate at
high speed. Never use discs repaired with plastic tape or glue, as it
will lead to damage. After playing, if you hear strange noise or the
unit flatters, e.g. the disc does not turn smoothly, please stop playing
immediately.
(8) Please remove the discs after use and put them into cases and store
them in vertical position. Tilting or piling may lead to warping.
Please keep the discs away from direct sunlight, high temperature
and humidity.
Do not stick labels onto discs.
Do not scratch the surface of discs.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
X. Maintenance
1). Cleaning the cabinet
Use a soft cloth slightly moistened with a mild detergent solution. Do not
use a solution containing alcohol, spirits, ammonia or abrasives.
2). Cleaning discs
When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc
from the centre outwards.
Do not use solvents such as benzine, thinners, commercially available
cleaners, or antistatic spray intended for analogue records.
WARNING:
To prevent fire or shock hazard, do not expose this unit to rain or moisture.
Do not remove cover, no user serviceable parts inside, refer servicing to
qualified service personnel.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
XI. Specifications
Screen size, visible
Screen format
19 inch
16:9
Resolution
1440 * 900
Minimum contrast ratio
Minimum brightness
Display colors
500:1
300 cd/m²
16M
Minimum viewing angle
Maximum response Time
160° (horizontal) / 160° (vertical)
8 ms
Minimum lifetime background light 50,000 hours
Video color systems PAL/NTSC3.58/NTSC4.43
TV Standard
PAL BG/I/DK
TV tuning system
Auto Preset tuning
TV
Tuner
Integrated and frequency synthesis
FUNCTION
CATV (optional)
Number of channels
Videotext / Teletext
Stereo systems (Optional)
Video
S1~S41 ch, Hyper Band
250
10 pages
Nicam-BG, I,DK/GR-GB, A2 for B/G/D/K
Composite video *1
Terminals
S-Video
S-video *1
PC
1
Audio L
1
Audio R/MONO
YUV
1
1
OSD language
Audio output
English//French/Spanish/ Italian, etc
3W * 2
Gross weight
9 Kgs
Power requirement
Power Consumption
DC 12V 5A, AC100~250V, 50Hz/60Hz
Max 60W
32
Download from Www.Somanuals.com. All Manuals Search And Download.
XII. Display modes
Resolution
Horizontal Freq. (KHz)
Vertical Freq. (Hz)
720x400
31.5
31.5
70
70
640x400
640x480(VGA)
640x480(VGA)
640x480(VGA)
800x600(SVGA)
800x600(SVGA)
800x600(SVGA)
1024x768(XGA)
1024x768(XGA)
1024x768(XGA)
1280x1024(SXGA)
31.5
37.9
37.5
37.9
47.2
46.9
48.4
56.5
60.0
63.5
60
72
75
60
72
75
60
70
75
60
1280x1024(SXGA)
80.0
75
1.
Modes, which are not listed in the above table, may not be supported.
For an optimal picture it is recommended to choose a mode listed in the
table.
2.
3.
You have 13 available modes compatible with windows.
It can happen that the image is disrupted. This can occur as result of a
signal from the VGA cad, which does not correspond with the usual
standard. This is not, however, an error. You can improve this situation
by altering an automatic setting or by manually changing the phase
setting and the pixel frequency menu.
4.
5.
If you switch off the TV/monitor, interference lines can occur on your
screen. But it’s not a problem, no need to concern about it.
To extend the service life of the product, we recommend that you use
your computer’s power management function.
Note: Design and specifications are subject to change without notice.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
GUARANTEE
Please keep your receipt as proof of purchase. This product is warranted for
any defect in materials or workmanship for three years after the original date
of purchase. This product is for normal domestic and office use only. This
warranty does not cover damage from misuse or neglect, accidental damage,
vermin infestation, excessive voltages such as lightning or power surges or
any alternation that affects the performance or reliability of the product.
If guarantee is required please contact the Grundig Helpline
1800 509 394 within Australia or the 0800 450 259 within New
Zealand.
Have your receipt of purchase on hand.
This guarantee is subject to the following provisions:
● It is only valid within boundaries of the country of purchase;
● The product must be correctly assembled and operated in accordance
with the instructions contained in this manual;
● This product must be used solely for domestic purposes;
● The guarantee does not cover accidental damage;
● The guarantee will be rendered invalid if the product is resold or has
been damaged by inexpert repair;
● The manufacturer disclaims any liability for incidental or consequential
damaged.
This guarantee is in addition to, and does not diminish, your statutory or
legal right.
Grundig Australia PO BOX 6287 SILVERWATER NSW 1811
Grundig Helpline: 1800 509 394 Australia
Grundig Helpline: 0800 450 259 New Zealand
34
Download from Www.Somanuals.com. All Manuals Search And Download.
|