model t10699
doWndraft sanding
table Kit
instructions
For questions or help with this product contact Tech Support at (570) 546-9663 or [email protected]
introduction
cut list
this kit allows you to create your own custom
downdraft sanding table. you just need to con-
struct the box, add a dust port, and connect it to
your dust collector or shop vacuum. Multiple kits
can also be combined to build larger tables.
id part
t
W
165⁄8
63⁄4
63⁄4
63⁄4
l
Qty
1
1
1
1
1
1
1
a
b
C
d
e
F
bottom piece
⁄
⁄
⁄
⁄
⁄
⁄
2"
2"
2"
2"
2"
2
"
"
263⁄4
263⁄4
263⁄4
173⁄4
165⁄8
263⁄4
"
"
"
Front piece
rear piece
side piece
insert
"
1
"
"
"
1
"
2
Kit includes (4) downdraft panels, (64) rubber
downdraft grommets, (4) plastic work stops with
nuts, and (1) 4" dust port. each panel measures
91⁄2
"
"
2
3
guide bar
⁄
8
"
2
13
63⁄4" W x 161⁄2" l and is ⁄16" high.
Kit inventory
x 64
Example of Finished Kit
C
B
A
Model t10699 downdraft sanding table Kit
building material & fasteners
these instructions are designed for construction
with 1⁄2" sheet stock. if desired, you can substitute
the sheet stock with the wood type of your choice.
E
E
D
D
if using a different material thickness than speci-
fied, adjust the length of side pieces (d).
you also need to determine how you will fasten
the various kit components together, depending
on the desired quality. Common options are wood
screws, glue, brad nails/staples, biscuits, rabbets,
dovetails, or any combination of these together.
F
1
⁄
2" x 301⁄2" x 48" sheet stock
Copyright © February, 2013 by grizzly industrial, inC.
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
For Kits ManuFaCtured sinCe 2/13 #tr15633 printed in taiWan
Download from Www.Somanuals.com. All Manuals Search And Download.
5. attach guide bars (F) to Front piece (b) and
rear piece (C) with top edges along the lines
you marked in the previous step.
8. attach side pieces (d) to bottom piece (a)
and rear piece (C).
C
D
C
A
B
D
9. Miter cut one end of inserts (e) at 60° and the
other end at 30°.
6. position one side piece (d) between Front
piece (b) and rear piece (C), then place
a straightedge against the bottom of guide
bars (F) and mark a line across side piece
(d). repeat with the other side piece (d).
60°
30°
E
these lines will help you position inserts (e)
during a later step.
10. place the 60° ends of inserts (e) just below
the lines on side pieces (d), then attach
inserts (e) to side pieces (d) and bottom
piece (a).
Line Indicating
Bottom Edge
of Guide Bars
B
60°
D
C
E
C
E
A
D
7. attach rear piece (C) to bottom piece (a).
30°
C
A
-3-
Model T10699 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
11. attach Front piece (b) to bottom piece (a)
and side pieces (d).
operation
the downdraft sanding table helps reduce air-
borne dust while sanding with a handheld electric
sander.
the dust port is connected to a shop vacuum or
dust collector, and a workpiece is placed on top
the downdraft table and sanded with an electric
handheld sander. as dust comes off the sander,
it is sucked through the downdraft table holes
and into the vacuum or dust collector—instead of
becoming airborne in the shop.
C
E
A
E
B
D
to reduce risk of eye inju-
ry or lung damage from
dust, always wear safety
goggles and a respirator
when operating machine!
12. place the panels on guide bars (F).
Work stops
the downdraft table kit includes four work stops.
the work stops can be placed inside the panel
holes to act as a barrier, preventing unwanted
workpiece movement when sanding.
Work Stops
13. attach dust port over hole in rear piece (C).
replacement parts
replacement rubber grommets and work stops
can be purchased if they get lost or damaged.
PT10699001
PT10699002
-4-
Model T10699 (Mfg. Since 2/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
|