Grizzly Trimmer T10051 User Manual

MODEL T10051  
12" BENCH SHEAR  
INSTRUCTIONS  
1. Overloading this tool can cause injury  
from flying parts if the tool breaks. Do  
not exceed the tool capacities.  
2. NEvER operate the bench shear with-  
out the plastic safety guard in place.  
4. Always chamfer and de-burr sharp  
sheet metal edges before bending in  
the bench hand brake. Sharp edges on  
sheet metal can result in severe cuts.  
5. NEvER place your hands between the  
blades of the shear.  
6. Always wear leather gloves and  
approved safety glasses when using  
this machine.  
7. Inspect the bench shear for any cracked  
components or loose fasteners. Correct  
any problems before use. Loose hard-  
ware or cracks could result in sudden,  
unexpected movements during use.  
8. DO NOT allow children to play with the  
bench shear.  
Figure 1. Model T10051.  
Specifications  
Maximum Cut Length..................................... 12"  
Cutting Capacities (Thickness):  
Steel ...................................................0.020"  
Aluminum............................................0.050"  
Brass .................................................. 0.025"  
Weight .......................................................28 lbs.  
9. If at any time you are experiencing  
difficulties performing the intended  
operation, STOp using the tool and  
contact our Technical Support at (570)  
546-9663, or ask a qualified expert how  
the operation should be performed.  
Damage to your eyes and hands could result  
from using this tool without proper protec-  
tive gear. Always wear safety glasses and  
heavy gloves when operating this machine.  
If you need help with your new item, call our Tech  
Support at: (570) 546-9663.  
CopyrighT © oCToBer, 2008 By grizzLy induSTriAL, inC.  
WARNINg: NO pORTION OF THIS MANUAL MAy BE REpRODUCED IN ANy SHApE  
OR FORM WITHOUT THE WRITTEN AppROvAL OF gRIzzLy INDUSTRIAL, INC.  
#jB11263 prinTed in ChinA  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
1. Mark your workpiece along the line that you  
Cleaning  
Cleaning the Model T10051 is relatively easy.  
periodically wipe down the machine to remove  
dust and oil. Treat all unpainted surfaces with a  
non-staining lubricant after cleaning.  
want to shear.  
2. Align the mark you made in Step 1 with the  
shear blades.  
Lubrication (Figure 6)  
Lubricating the Model T10051 consists of applying  
oil to the pivoting and sliding surfaces.  
Injury to your hands and fingers could result  
from improper use of this tool. Never place  
your hand in the path of the blade while  
using this tool and never use the tool with-  
out the safety guard in place.  
To lubricate the model T10051:  
1. Apply 3-4 drops of oil to the areas indicated  
in Figure 6 so that oil will penetrate between  
the sliding surfaces. raise and lower the  
handle several times to disperse the oil.  
NOTICE  
2. Wipe any excess oil from these areas to pre-  
If you have never used this type of machine  
or equipment before, we strongly recom-  
mend that you read books, trade magazines,  
or get formal training before beginning any  
projects. Regardless of the content in this  
section, grizzly Industrial will not be held  
liable for accidents caused by lack of train-  
ing.  
vent dust and grime build-up.  
3. use your left hand to hold the workpiece  
steady on the tool base while you lower the  
handle with your right hand to produce the  
cut. do not reach around the blade with your  
right hand to hold the workpiece.  
Work Stop  
The Model T10051 is equipped with a work stop  
that allows you to create identical cuts in multiple  
workpieces.  
Figure 6. Lubrication locations (left side shown).  
To use the work stop:  
1. Mark your workpiece along the line that you  
want to shear.  
2. Align the mark you made in Step 1 with the  
shear blades.  
3. Slide the work stop against the workpiece  
and tighten the work stop knob.  
4. For the following cuts, place the workpiece on  
the tool base so that it rests against the work  
stop, then proceed with the cut.  
-3-  
T10051 14" portable Benchtop Brake  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. use a ball head 3mm hex wrench to adjust  
the blade adjustment screws to fine-tune the  
position of the fixed blade (Figure 8).  
Blade Adjustments  
The fixed (lower) blade on the Model T10051 is  
adjustable to allow for different materials and to  
compensate for wear to the blades. The blade  
position is factory set and only needs to be adjust-  
ed if there is excessive binding between the fixed  
and moving blade or if a gap exists between the  
blades that causes the workpiece to bend, rather  
than shear between the blades.  
—Turning the blade adjustment screw clock-  
wise will move the fixed blade outward,  
towards the moving blade.  
—Turning the blade adjustment screw coun-  
terclockwise will move the fixed blade  
inward, away from the moving blade.  
The ideal blade adjustment will vary depending on  
the material and dimensions of your workpiece.  
Above all, make sure the fixed blade is parallel  
with the moving blade and contacts it evenly along  
the entire width.  
To adjust the blade:  
1. remove the blade guard.  
2. Loosen, but do not remove the four blade cap  
screws (Figure 7).  
Blade Adjustment  
Screw  
Blade Cap  
Fixed Blade  
Screws  
Figure 8. Adjustment screw.  
4. once the fixed blade is set parallel to the  
moving blade, tighten the four blade cap  
screws, then re-install the blade guard.  
5. Test the performance of the shear on a scrap  
workpiece.  
Blade Adjustment  
if the results are satisfactory, no further  
adjustment is necessary.  
Screws  
Figure 7. Blade adjustment.  
if the results are not satisfactory, repeat  
Steps 1–5 until the results meet your stan-  
dards.  
-4-  
T10051 14" portable Benchtop Brake  
Download from Www.Somanuals.com. All Manuals Search And Download.  
T10051 parts Breakdown  
&*  
*&  
*%  
))  
,
+
&-  
')  
)%  
)'  
&.  
'%  
'&  
'(  
(,  
&)  
''  
-
),  
)&  
.
)*  
)+  
*
)(  
(-  
'-  
(*  
(*  
(
'*  
)-  
&+  
)
((  
()  
'+  
&%  
(.  
',  
'
'.  
(&  
(%  
&,  
&,  
(%  
('  
).  
).  
(+  
Labels  
&
&&  
&'  
&%&  
&(  
&%'  
-5-  
T10051 14" portable Benchtop Brake  
Download from Www.Somanuals.com. All Manuals Search And Download.  
T10051 parts List  
REF PART #  
DESCRIPTION  
REF PART #  
DESCRIPTION  
1
PT10051001  
TABLE  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
101  
102  
PB126M  
HEX BOLT M8-1.25 X 40  
LOCK NUT M8-1.25  
2
PT10051002  
PT10051003  
PT10051004  
PT10051005  
PT10051006  
PT10051007  
PT10051008  
PT10051009  
PT10051010  
PT10051011  
PT10051012  
PT10051013  
PT10051014  
PT10051015  
PT10051016  
PT10051017  
PT10051018  
PB26M  
FIXED BLADE BASE  
MOVING BLADE BASE  
MOVING BLADE  
PLN04M  
3
PFH43M  
FLAT HD SCR M6-1 X 10  
SET SCREW M10-1.5 X 16  
BUTTON HD CAP SCR M5-.8 X 16  
PHLP HD SCR M5-.8 X 10  
LOCK NUT M10-1.5  
4
PSS75M  
5
BLADE BRACE  
PSBS16M  
PS09M  
6
JOINTING PLATE (LEFT)  
JOINTING PLATE (RIGHT)  
FASTEN PLATE 1  
FASTEN PLATE 2  
BLADE PIVOT PLATE  
TABLE STOP  
7
PLN05M  
8
PT10051035  
PFH43M  
BUTTON HD CAP SCR M5-.8 X 5  
FLAT HD SCR M6-1 X 10  
HANDLE SPACER  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
PT10051037  
PT10051038  
PT10051039  
PW04M  
BRACKET SPACER  
TABLE GAUGE  
PIVOT SPACER  
LEG  
FLAT WASHER 10MM  
FLAT WASHER 6MM  
WORK STOP ROD  
BLADE GUARD  
PW03M  
HANDLE  
PT10051042  
PT10051043  
PT10051044  
PB126M  
FIXED BLADE  
SPECIAL BOLT M10-1.5 X 30  
KNOB M8-1.25 X 25  
L-BRACKET  
BUTTON HD CAP SCR M10-1.5 X 40  
HEX BOLT M8-1.25 X 30  
LOCK NUT M10-1.5  
LOCK NUT M8-1.25  
LOCK NUT M6-1  
HEX BOLT M8-1.25 X 40  
BLADE SPACER  
PT10051046  
PW01M  
PLN05M  
FLAT WASHER 8MM  
FLAT WASHER 8MM  
FLAT WASHER 5MM  
HANDLE GRIP  
PLN04M  
PW01M  
PLN03M  
PW02M  
PT10051023  
PSB38M  
SPECIAL BOLT M6-1 X 16  
CAP SCREW M5-.8 X 25  
HEX BOLT M6-1 X 20  
HEX BOLT M10-1.5 X 40  
LOCK NUT M10-1.5  
PT10051050  
PT10051051  
PT10051101  
PT10051102  
WORK STOP  
PB08M  
BLADE DANGER LABEL  
BLADE GUARD WARNING LABEL  
PB31M  
PLN05M  
Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine  
MUST maintain the original location and readability of the labels on the machine. If any label is  
removed or becomes unreadable, REpLACE that label before using the machine again. Contact  
grizzly at (800) 523-4777 or www.grizzly.com to order new labels.  
-6-  
T10051 14" portable Benchtop Brake  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Hamilton Watch Watch Khaki Navy Regatta Automatic User Manual
HANNspree Flat Panel Television DT07 10A1 User Manual
HANNspree Flat Panel Television ST59 23C1 User Manual
Hans Grohe Plumbing Product 06888XX0 User Manual
Harbor Freight Tools Greenhouse Kit 94241 User Manual
Harbor Freight Tools Paint Sprayer 93305 User Manual
Hearth and Home Technologies Ventilation Hood HRV200PLUS User Manual
Hotpoint Oven 60cm Gas Cooker User Manual
Hotpoint Refrigerator HTS18CCS User Manual
HSM Paper Shredder HSM FA 5002 User Manual