CUTTING TOOL
MODEL H0604
INSTRUCTION MANUAL
COPYRIGHT © 2000 BY GRIZZLY INDUSTRIAL, INC.
1821 VALENCIA ST., BELLINGHAM, WA 98227
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are
intended to convey the level of importance of the safety messages. The progres-
sion of symbols is described below. Remember that safety messages by them-
selves do not eliminate danger and are not a substitute for proper accident pre-
vention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful information
about proper operation of the equipment.
NOTICE
Safety Instructions For Power Tools
1. KEEP ALL SAFETY DEVICES IN
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept a safe distance from
work area.
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from tool
before turning on.
6. MAKE WORK SHOP CHILD
PROOF with padlocks, master
switches, or by removing starter
keys.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.
7. DON’T FORCE TOOL. It will do the
job better and safer at the rate for
which it was designed.
4. DON’T USE IN DANGEROUS
ENVIRONMENT. Don’t use power
tools in damp or wet locations, or
where any flammable or noxious
fumes may exist. Keep work area
well lighted.
8. USE RIGHT TOOL. Don’t force tool
or attachment to do a job for which it
was not designed.
-1-
H0604 Cutting Tool
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions For Power Tools
9. USE PROPER EXTENSION CORD
14. MAINTAIN TOOLS WITH CARE.
for the tool. Make sure your exten-
sion cord is in good condition.
Conductor size should be in accor-
dance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged.
Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and
changing accessories.
15. DISCONNECT TOOLS before ser-
vicing and changing accessories,
such as blades, bits, cutters, and
the like.
16. REDUCE THE RISK OF UNINTEN-
TIONAL STARTING. Make sure
switch is in off position before plug-
ging in.
17. USE RECOMMENDED ACCES-
SORIES. Consult the owner’s man-
ual for recommended accessories.
The use of improper accessories
may cause risk of injury.
Minimum Gauge for Extension Cords
AMP
RATING
0-6
LENGTH
50ft
16
25ft
18
18
16
14
12
10
100ft
16
14
14
12
18. CHECK
DAMAGED
PARTS.
7-10
16
16
12
12
Before further use of the tool, a
guard or other part that is damaged
should be carefully checked to
determine that it will operate proper-
ly and perform its intended function.
Check for alignment of moving
parts, binding of moving parts,
breakage of parts, mounting, and
any other conditions that may affect
its operation. A guard or other part
that is damaged should be properly
repaired or replaced.
11-12
13-16
17-20
21-30
10
No
10
10. WEAR PROPER APPAREL. Do not
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewel-
ry which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.
11. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
glasses only have impact resistant
lenses, they are NOT safety glass-
es.
No list of safety guidelines can be
complete. Every shop environment is
different. Always consider safety
first, as it applies to your individual
working conditions. Use this and
other machinery with caution and
respect. Failure to do so could result
in serious personal injury, damage to
equipment or poor work results.
12. SECURE WORK. Use clamps or a
vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.
13. DON’T OVERREACH. Keep proper
footing and balance at all times.
-2-
H0604 Cutting Tool
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Commentary
We are proud to offer the Grizzly Model
H0604 Cutting Tool. The Model H0604 is
part of a growing Grizzly family of fine
power tools. When used according to the
guidelines set forth in this manual, you can
expect years of trouble-free, enjoyable
operation and proof of Grizzly’s commit-
ment to customer satisfaction.
The specifications, details, and pho-
tographs in this manual represent the
Model H0604 as supplied when the manu-
al was prepared. However, owing to
Grizzly’s policy of continuous improve-
ment, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
The Model H0604 Cutting Tool is great for
cutting holes in drywall or plywood sheath-
ing. When equipped with a spiral cutter
(sold separately), this tool can plunge cut
like a drill and cut sideways like a jig saw.
Operates at 28,000 RPM. A number of
accessories for the Model H0604 are
available through the Grizzly catalog.
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
We are pleased to provide this manual
with the Model H0604. It was written to
encourage safety considerations and
guide you through general operating pro-
cedures and maintenance. It represents
our effort to produce the best documenta-
tion possible.
Grizzly Industrial, Inc.
2406 Reach Road
Williamsport, PA 17701
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
To operate this, or any power tool,
safely and efficiently, it is essential to
become as familiar with its character-
istics as possible. The time you invest
before you begin to use your Model
H0604 will be time well spent. DO NOT
operate this machine until you are
completely familiar with the contents
of this manual. Make sure you read
and understand all of the safety proce-
dures. If you do not understand some-
thing, DO NOT operate the machine.
The Model H0604 was specifically
designed for cutting and boring
holes. Do not modify and/or use this
machine for any other purpose.
Modifications or improper use of
this tool will void the warranty. If you
are confused about any aspect of
this machine, DO NOT use it until
you have answered all your ques-
tions. Serious personal injury may
occur.
-3-
H0604 Cutting Tool
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
Inserting and Removing Bits
UNPLUG TOOL WHEN CHANGING BITS
1. Push the silver spindle lock button on
the side of the cutter and turn silver
collet with fingers until the lock
engages.
Operating this equipment has the
potential for flying debris to cause eye
injury. Always wear safety glasses or
goggles when operating equipment.
Everyday glasses or reading glasses
only have impact resistant lenses, they
are not safety glasses. Be certain the
safety glasses you wear meet the
appropriate standards of the American
National Standards Institute (ANSI).
2. Use the supplied wrench to loosen
the silver collet while continuing to
push the spindle lock button.
3. Slide the desired bit into the collet as
far as possible without covering the
bit’s cutting edge.
4. With the spindle lock button still
pressed, tighten the collet with the
supplied wrench until securely seat-
ed. Do not over tighten.
Like all power tools, there is danger
associated with the Model H0604.
Accidents are frequently caused by
lack of familiarity or failure to pay
attention. Use this tool with respect
and caution to lessen the possibility of
operator injury. If normal safety pre-
cautions are overlooked or ignored,
serious personal injury may occur.
Operating the cutting tool
1. With appropriate bit in place, turn
power switch on and slowly engage
bit into or against the material to be
cut. Do not turn power on while the bit
is resting against surface to be cut.
2. If at any time during the cut the blade
stalls or stops abruptly, turn power off
immediately and wait for blade to
come to rest before removing from
material.
3. Do not make a blind cut into a wall
without first determining if there are
hazards behind the material to be
cut. Check behind walls for wires,
other electrical hazards, or plumbing.
4. Make sure to use the appropriate bit
for the specified cutting task.
-4-
H0604 Cutting Tool
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Operating Guides and Tips
Maintenance
Avoid overloading the cutting tool
Always use sharpened cutting bits.
Do not apply excessive pressure to
the cutting tool while using. If the
speed drops abnormally, decrease
pressure immediately. If the bit stops
abruptly or becomes blocked,
release the trigger at once.
Regular periodic maintenance on your
H0604 will ensure its optimum perfor-
mance. Make a habit of inspecting your
tool each time you use it. Check for the fol-
lowing conditions and repair or replace
when necessary:
1.
2.
3.
4.
Loose fasteners.
Worn switch.
Worn or damaged cords and plugs.
Any other condition that could ham-
per the safe operation of this
machine.
Ensure the safety of the workplace.
Clear the work area of all parts and
debris that may cause injury by flying
objects. Securely fix the object to be
cut or fastened in a vise or otherwise
clamp to avoid injury. Do not attempt
to hold workpiece by hand.
Since this tool is encased in a double insu-
lated plastic cover, leave repair and ser-
vice issues to a qualified service techni-
cian. This includes brush replacement,
lubrication or any other internal operation.
Inspect the cutting tool before use. Run
the cutting tool before using to
ensure all parts are running smooth-
ly and there are no abnormal sounds
or sparks. If any defect is found,
have unit serviced.
Ensure that no air passages get blocked. If
they do, blow them out with compressed
air. WARNING: Wear safety glasses when
cleaning tool with compressed air.
Know your worksite. Only cut as deep as
necessary. Check behind walls for
wires, other electrical hazards, or
plumbing.
Plastic parts can easily be cleaned with a
damp cloth, but never use water to clean
any electrical parts. Solvents should also
be avoided on plastic because of the pos-
sibility of damage.
Disassembly and improper reassem-
bly of this device can result in electri-
cal shock danger. Always have this
device serviced by an qualified elec-
trical repair technician. Serious injury
will result.
The potential for injury using this
device is great. Use extreme caution
and care when operating, adjusting and
maintaining this saw. Failure to observe
safe handling practices will result in
serious personal injury.
-5-
H0604 Cutting Tool
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Number’’, which must be clearly posted on the outside as
well as the inside of the carton. We will not accept any item back without this number. Proof
of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
2406 Reach Road
Williamsport, PA 17701
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon.
-6-
H0604 Cutting Tool
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
Model # H0604 Cutting Tool
Order #_______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
___Miter Saw
___Other_________________________________
3. What is your age group?
___20-29
11. What machines/supplies would you like Grizzly
Industrial to carry?
___50-59
___60-69
___70 +
___30-39
___40-49
___12" Table Saw
___12" Jointer
___Radial Arm Saw
___Panel Saw
___Lumber
___Brass Hardware
4. How long have you been a woodworker?
___Paint & Finishing Supplies
___Contractor’s Supplies
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
___Combination Planer/Jointer
___Other_________________________________
5. How would you rank your woodworking skills?
___Simple
___Advanced
___Intermediate
___Master Craftsman
12. What new accessories would you like Grizzly
Industrial to carry?
6. What stationary woodworking tools do you own?
Check all that apply.
___Builders Hardware
___Fasteners
___Hand Tools
___Air Compressor
___Band Saw
___Panel Saw
___Planer
___Wood Components
___Other_________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
13. What other companies do you purchase your tools
and supplies from?
_________________________________________
_________________________________________
_________________________________________
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
14. Do you think your purchase represents good value?
___Other______________________________
___Yes
___No
7. How many of your woodworking machines are
Grizzly? _____________
15. Would you recommend Grizzly to a friend?
___Yes ___No
8. Which benchtop tools do you own? Check all
that apply.
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___Yes
___No
___8" Table Saw
___Scroll Saw
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___8" - 10" Bandsaw
___Disc/Belt Sander
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___Other______________________________
-7-
H0604 Cutting Tool
Download from Www.Somanuals.com. All Manuals Search And Download.
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|