model g0636Xb
ultimate 17" bandsaW
w/motor braKe
manual insert
the Model g0636XB is the same as the Model g0636X, except it has a magnetic brake motor and a square
fence rail. Besides the instructions, data sheet, circuit requirements, parts, and wiring diagram in this insert,
the content in the Model g0636X owner's manual is the same for both machines. Before operating your
new machine, you Must read and understand this insert and the entire Model g0636X manual to reduce
the risk of injury from improper use or setup.
If you have any further questions about this manual insert or the differences between the Model g0636XB
and the Model g0636X, contact our Technical Support at (570) 546-9663 or email techsupport@grizzly.
com.
hardware and tools (not shown)
Qty
machine inventory
after all the parts have been removed from the
crate, you should have the following items:
hex Wrench 5mm.............................................. 1
hex Wrench 6mm.............................................. 1
open end Wrench 10 x 13................................ 1
open end Wrench 17 x 19................................ 1
lifting rings....................................................... 2
resaw Fence lock handle M8-1.25 x 44
(resaw Fence).................................................. 1
Moving plate (resaw Fence)............................ 1
Flat Washer 8mm (resaw Fence) .................... 1
crate contents (figure 1):
Qty
a. Bandsaw (not shown)................................. 1
b. Miter gauge................................................ 1
c. Fence.......................................................... 1
d. resaw Fence ............................................. 1
e. guide post handwheel............................... 1
installing fence
components and hardware needed:
Qty
B
Fence assembly................................................ 1
resaw Fence assembly.................................... 1
resaw Fence lock handle M8-1.25 x 44 ......... 1
Moving plate...................................................... 1
Flat Washer 8mm.............................................. 1
C
to install the fence:
1. remove the cap screw, knobs, and washers
that hold the rail onto the table, then remove
the rail.
d
e
2. Flip the rail over and reinstall with the fast-
ners removed in step 1.
figure 1. g0636XB inventory.
3. install the fence handle on the fence, if it is
not already installed.
Copyright © june, 2008 By grizzly industrial, inC.
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
#Bl10818 printed in taiWan
Download from Www.Somanuals.com. All Manuals Search And Download.
aligning fence
to ensure cutting accuracy when the fence is first
installed, the fence should be aligned with the
miter slot.
to align the fence parallel with the miter slot:
1. disConneCt BandsaW FroM poWer!
OFF Button
figure 5. resetting the switch.
2. Make sure the miter slot is aligned with the
bandsaw blade (see g0636X Manual page
25, Aligning Table).
6. turn the switch disabling key to "0", as shown
in figure 4.
3. Mount the fence next to the miter slot, then
loosen the knobs and cap screw that secure
the fence rail to the table.
7. try to turn the machine ON.
—if the bandsaw does not start, the switch
disabling feature is working as designed.
the test run is complete.
4. adjust the fence face parallel with the edge of
the miter slot, as shown in figure 7.
—if the bandsaw starts, immediately discon-
nect power. the switch disabling feature is
not working correctly. this safety feature
must work properly before proceeding with
regular operations. Call tech support for
help.
motor brake
the motor brake is activated automatically when
the oFF button is pushed, quickly bringing the
blade to a stop.
accessories
t10131—extension table for g0636Xb
easily attaches to the main table of your bandsaw
and provides additional support for large
workpieces.
figure 7. example of fence square with miter
slot.
5. tighten the knobs and cap screw that secure
the rail to the table, being careful not to move
the fence.
NOTICE
adjusting the fence parallel to the miter slot
does not guarantee straight cuts. the miter
slot may need to be adjusted parallel to the
side of the blade. refer to the "aligning
table" instructions in the g0636X manual
on page 25.
figure 6. Model t10131 extension table
attached to g0636XB bandsaw.
Model g0636XB
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
pointer calibration
magnetic brake adjustment
your new bandsaw is equipped with a fence mea-
surement system that includes a fence pointer,
which must be calibrated when the bandsaw is
first set up.
the space between the magnetic brake and brake
shoe is preset by the factory at 0.2mm (0.008").
however, you should adjust this space every two
to three years, or when it takes over five seconds
for the brake to stop the motor.
to calibrate the pointer:
tools needed
1. if the fence is mounted on the right-hand side
of the blade, remove it and re-install it on the
left-hand side of the blade.
phillips head screwdriver ................................. 1
us dollar Bills or 0.008" Feeler gauges........... 2
hex Wrench 3mm.............................................. 1
hex Wrench 4mm.............................................. 1
2. place the fence flush against the bandsaw
blade (figure 8).
to adjust the space between the magnetic
brake and brake shoe:
1. disConneCt BandsaW FroM poWer!
2. remove the motor fan cover, then loosen the
cap screws securing the motor fan and brake
shoe (see figure 10).
3. Fold two dollar bills in half and slide them (or
feeler gauges) between the brake shoe and
magnetic brake on both sides (see figure
10).
4. slide the fan toward the brake until you feel
a slight resistance when moving the bill, then
tighten the cap screws on the brake shoe and
motor fan, then reinstall the motor fan cover.
figure 8. Fence flush with blade.
3. loosen the pointer adjustment screw (figure
9) and set the pointer in line with "0" and the
measurement scale on the table.
on
off
Brake
pointer screw
pointer
shoe
Cap
screw
Magnetic
Brake
Motor
Fan
figure 10. adjusting distance between magnetic
brake and brake shoe.
figure 9. Calibrating fence pointer (screw out of
view).
4. tighten the pointer adjustment nut.
-4-
Model g0636XB
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE DATA
SHEET
8jhidbZgꢀHZgk^XZꢀꢁ/ꢀꢂ*,%ꢃꢀ*)+".++(ꢀ™ꢀIdꢀDgYZgꢀ8Vaa/ꢀꢂ-%%ꢃꢀ*'("),,,ꢀ™ꢀ;Vmꢀꢁ/ꢀꢂ-%%ꢃꢀ)(-"*.%&
MODEL G0636XB
17" ULTIMATE BANDSAW w/MOTOR BRAKE
Product Dimensions:
LZ^\]iꢀꢀ###########################################################################################################################################################################+'%ꢀaWh#
AZc\i]$L^Yi]$=Z^\]iꢀꢀ################################################################################################################################# (*&¿)ꢄꢀmꢀ(((¿)ꢄꢀmꢀ,-&¿'
;ddiꢀEg^ciꢀꢂAZc\i]$L^Yi]ꢃꢀ####################################################################################################################################### '.&¿'ꢄꢀmꢀ'(&¿'
ꢄ
ꢄ
Shipping Dimensions:
IneZꢀ################################################################################################################################################################# LddYꢀHaViꢀ8gViZ
8dciZciꢀ########################################################################################################################################################################## BVX]^cZ
LZ^\]iꢀ############################################################################################################################################################################+,*ꢀaWh#
AZc\i]$L^Yi]$=Z^\]iꢀ######################################################################################################################################(+&¿'ꢄꢀmꢀ',&¿'ꢄꢀmꢀ--ꢄ
Electrical:
Hl^iX]ꢀ######################################################################################################################## BV\cZi^Xꢀl$I]ZgbVaꢀDkZgadVYꢀEgdiZXi^dc
Hl^iX]ꢀKdaiV\Zꢀ################################################################################################################################################################### ''%K
GZXdbbZcYZYꢀ8^gXj^iꢀH^oZꢀ############################################################################################################################################(%ꢀVbe
GZXdbbZcYZYꢀEaj\ꢀIneZꢀ#################################################################################################################################################A+"(%
Eaj\ꢀ>cXajYZYꢀ######################################################################################################################################################################### Cd
Motor:
IneZꢀ######################################################################################################################################### I:;8ꢀ8VeVX^idgꢀHiVgiꢀ>cYjXi^dc
=dghZedlZgꢀ#########################################################################################################################################################################*ꢀ=E
KdaiV\Zꢀ############################################################################################################################################################################### ''%K
E]VhZꢀ################################################################################################################################################################################H^c\aZ
6behꢀ#################################################################################################################################################################################### ''6
HeZZYꢀ#########################################################################################################################################################################&,'*ꢀGEB
8nXaZꢀ################################################################################################################################################################################# +%ꢀ=o
CjbWZgꢀD[ꢀHeZZYhꢀ###################################################################################################################################################################&
EdlZgꢀIgVch[Zgꢀ###########################################################################################################################################################7Zaiꢀ9g^kZ
7ZVg^c\hꢀ######################################################################################################################### H]^ZaYZYꢀVcYꢀEZgbVcZcianꢀAjWg^XViZY
7gV`Zꢀ##########################################################################################################################################7j^ai">cꢀBV\cZi^XꢀIneZꢀ.%K98
Main Specifications:
Operation Information
7aVYZꢀHeZZYꢀ#####################################################################################################################################################)*%%ꢀ;EB
IVWaZꢀI^aiꢀ################################################################################################################################################ AZ[iꢀ*•!ꢀG^\]iꢀ)*•
Cutting Capacities
BVm^bjbꢀ8jii^c\ꢀ=Z^\]iꢀ############################################################################################################################################# &+ꢄ
I]gdViꢀ8VeVX^inꢀAZ[iꢀd[ꢀ7aVYZꢀ####################################################################################################################################&+&¿'
ꢄ
Blade Information
HiVcYVgYꢀ7aVYZꢀAZc\i]ꢀ######################################################################################################################################&+%ꢄ"&+'ꢄ
7aVYZꢀL^Yi]ꢀGVc\Zꢀ############################################################################################################################################## &¿-ꢄ¶&(¿-
7aVYZꢀ<j^YZhꢀ################################################################################################################################################# 7Vaaꢀ7ZVg^c\
ꢄ
Model g0636XB
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Information
IVWaZꢀAZc\i]ꢀ############################################################################################################################################################### '&ꢁ
IVWaZꢀL^Yi]ꢀ###############################################################################################################################################################'*&¿'
IVWaZꢀI]^X`cZhhꢀ############################################################################################################################################################ 'ꢁ
;addgꢀidꢀIVWaZꢀ=Z^\]iꢀ#################################################################################################################################################(*&¿'
ꢁ
ꢁ
Fence Information
AdX`hꢀ^cꢀ;gdciꢀ##############################################################################################################################################################NZh
AdX`hꢀ^cꢀGZVgꢀ############################################################################################################################################################### Cd
6Y_jhiVWaZꢀ[dgꢀ7aVYZꢀAZVYꢀ###########################################################################################################################################NZh
GZhVlꢀ;ZcXZꢀEaViZꢀ=Z^\]iꢀ############################################################################################################################################ +ꢁ
Dust Collection
CjbWZgꢀd[ꢀ9jhiꢀEdgihꢀ######################################################################################################################################################'
H^oZꢀd[ꢀ9jhiꢀEdgihꢀ######################################################################################################################################################### )ꢁ
GZfj^gZYꢀ8;BꢀViꢀ:VX]ꢀ9jhiꢀEdgiꢀ######################################################################################################################)%%ꢀ8;B
Construction Materials
IVWaZꢀ######################################################################################################################################EgZX^h^dcꢀ<gdjcYꢀ8Vhiꢀ>gdc
IVWaZꢀIgjcc^dcꢀ###################################################################################################################################################8Vhiꢀ>gdc
G^eꢀ;ZcXZꢀ###########################################################################################################################################################8Vhiꢀ>gdc
GZhVlꢀ;ZcXZꢀ########################################################################################################################9ZajmZꢀ:migjYZYꢀ6ajb^cjb
L]ZZahꢀ###############################################################################################################################8dbejiZgꢀ7VaVcXZYꢀ8Vhiꢀ>gdc
I^gZꢀBViZg^Vaꢀ##########################################################################################################################################################GjWWZg
L]ZZaꢀ8dkZgꢀ######################################################################################################################################### EgZ";dgbZYꢀHiZZa
7dYnꢀ#####################################################################################################################################DcZꢀE^ZXZꢀGZ^c[dgXZYꢀHiZZa
EV^ciꢀ#########################################################################################################################################################EdlYZgꢀ8dViZY
Other Specifications:
8djcignꢀD[ꢀDg^\^cꢀ############################################################################################################################################################ IV^lVc
LVggVcinꢀ###########################################################################################################################################################################&ꢀNZVg
HZg^VaꢀCjbWZgꢀAdXVi^dcꢀ########################################################################################################## >9ꢀAVWZaꢀdcꢀJeeZgꢀL]ZZaꢀ8dkZg
6hhZbWanꢀꢂꢀHZijeꢀI^bZꢀ##################################################################################################################################################&ꢀ=djg
Features:
8Vhiꢀ>gdcꢀIVWaZꢀIgjcc^dc
7Vaaꢀ7ZVg^c\ꢀ7aVYZꢀ<j^YZh
Fj^X`ꢀ8]Vc\Zꢀ7aVYZꢀGZaZVhZ$IZch^dcZg
B^Xgd"6Y_jhi^c\ꢀGVX`ꢀꢂꢀE^c^dcꢀIVWaZꢀI^ai
GVX`ꢀꢂꢀE^c^dcꢀJeeZgꢀ7aVYZꢀ<j^YZꢀ=Z^\]iꢀ6Y_jhibZci
8dbejiZgꢀ7VaVcXZYꢀ8Vhiꢀ>gdcꢀL]ZZahꢀl^i]ꢀ<g^ooanꢀ7ZVgꢀ=ZVYꢀ8ji"Djih
7aVYZꢀIZch^dcꢀ>cY^XVidg
=Z^\]iꢀHXVaZꢀ[dgꢀJeeZgꢀ7aVYZꢀ<j^YZh
7aVYZꢀIgVX`^c\ꢀL^cYdl
=^c\ZYꢀL]ZZaꢀ8dkZghꢀl^i]ꢀHV[ZinꢀAdX`
9ZajmZꢀ8Vhiꢀ>gdcꢀ;ZcXZꢀl^i]ꢀ:migjYZYꢀ6ajb^cjbꢀGZhVlꢀ;ZcXZꢀ6iiVX]bZci
>cXajYZYꢀB^iZgꢀ<Vj\Z
>cXajYZYꢀ&ꢁꢀ7aVYZ
Ildꢀ)ꢁꢀ9jhiꢀEdgih
BdidgꢀHidehꢀ^cꢀJcYZgꢀ(ꢀHZXdcYhꢀ6[iZgꢀHl^iX]ꢀIjgcZYꢀD[[
Dei^dcVaꢀ:miZch^dcꢀIVWaZꢀl^i]ꢀHjeedgi
-6-
Model g0636XB
Download from Www.Somanuals.com. All Manuals Search And Download.
section 2: circuit reQuirements
power connection device
220v single-phase
the type of plug required to connect your machine
to power depends on the type of service you cur-
rently have or plan to install. We recommend
using the plug shown in figure 11.
serious personal injury could occur if you
connect the machine to power before com-
pleting the setup process. do not connect
the machine to the power until instructed
later in this manual.
electrocution or fire could
result if machine is not
grounded and installed in
compliance with electrical
codes. compliance must
be verified by a qualified
electrician!
figure 11. neMa l6-30 plug and receptacle.
extension cords
using extension cords may reduce the life of the
motor. instead, place the machine near a power
source. if you must use an extension cord:
full load amperage draw
this machine draws the following amps under
maximum load:
•
•
•
use at least a 10 gauge cord that does not
exceed 50 feet in length!
amp draw..............................................22 amps
the extension cord must also have a ground
wire and plug pin.
power supply circuit requirements
a qualified electrician Must size cords over
50 feet long to prevent motor damage.
you Must connect your machine to a grounded
circuit that is rated for the amperage given below.
never replace a circuit breaker on an existing cir-
cuit with one of higher amperage without consult-
ing a qualified electrician to ensure compliance
with wiring codes. if you are unsure about the
wiring codes in your area or you plan to con-
nect your machine to a shared circuit, consult
a qualified electrician.
Minimum Circuit size.............................30 amps
Model g0636XB
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
g0636Xb electrical components
figure 13. junction box wiring.
figure 12. Magnetic switch.
figure 14. Capacitors.
-8-
Model g0636XB
Download from Www.Somanuals.com. All Manuals Search And Download.
g0636Xb Wiring diagram 5hp 220v, 1-ph
A&ꢀ
A'ꢀ
<gdjcY
=di
EDL:Gꢀꢀ
HJEEANꢀꢀ
?JC8I>DCꢀ
7AD8@ꢀ
)
(
'
&
X
G
220 VAC
Y
N:AADL
=di
L6-30 PLUG
(as recommended)
<gdjcYꢀ
6ꢀ
A>B>IꢀHL>I8=
C8
8DCIGDAꢀE6C:A
ꢁk^ZlZYꢀ[gdbꢀWZ]^cYꢂ
A&$&ꢀ
A'$(ꢀ
CD&(ꢀ
A($*ꢀ
H9:
B6"&-
''%K
C8&*ꢀ
H9:ꢀ
C8&+ꢀ
''
&)
'&
&(
CD&)ꢀ
I&$'ꢀ
I'$)ꢀ
I($+ꢀ
H9:ꢀG6"(%ꢀ
&-"'+
''
&)
'&
&(
&$'ꢀ
($)ꢀ
*$+ꢀ
&-
.-ꢀ
'+
.+ꢀ
''
.*
''
&)
'&
&(
B6<C:I>8
HL>I8=
see
figure 12
''%K
BDIDG
see figures
<gdjcYꢀ
HiVgi
8VeVX^idg
(%%B;9
'*%K68
13 & 14
The motor wiring shown here is
current at the time of printing, but it
may not match your machine.
Always use the wiring diagram
inside the motor junction box.
BV\cZi^Xꢀ7gV`Z
NO<
Gjc
8VeVX^idg
)*B;9
)*%K68
Model g0636XB
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
main breakdown
-10-
Model g0636XB
Download from Www.Somanuals.com. All Manuals Search And Download.
main parts list
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
P0636X001
P0636X002
PN13M
HANDLE
49
50
51
52
53
54
55
56
57
58
59
60
61
62
65
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
85
94
P0636X049
P0636X050
P0636X051
P0636X052
P0636X053
PLW03M
STOP SWITCH
2
LEVER ROD M16-2
KEY SWITCH
3
HEX NUT M16-2
SWITCH PLATE
4
P0636X004
PSBS25M
PLW06M
ROTATE SHAFT
CONNECTING CORD
CONNECTING CORD
LOCK WASHER 6MM
ADJUST BOLT
5
BUTTON HD CAP SCR M10-1.5 X 20
LOCK WASHER 10MM
BLD TRACKING KNOB M10-1.5 x 25
BLD TRACKING LOCK LEVER 10MM
GD POST LOCK KNOB M10-1.5 X 25
MACHINE BODY
6
7
P0636X007
P0636X008
P0636X009
P0636X010
P0636X011
P0636X012
PSB31M
P0636X055
PB160M
8
HEX BOLT M10-1.5 X 70
HEX NUT M10-1.5
9
PN02M
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
PW04M
FLAT WASHER 10MM
SET SCREW M6-1 X 12
PULLEY
PILLOW BLOCK
PSS04M
CAM
P0636X060
PW01M
CAP SCREW M8-1.25 X 25
HEX BOLT M8-1.25 X 60
HEX NUT M8-1.25
FLAT WASHER 8MM
LOWER SHAFT
PB28M
P0636X062
PVA33
PN03M
V-BELT A-33 4L330
TRACKING WINDOW
RIVET 3.2 X 10
P0636X016
P0636X017
P0636X018
PSB31M
UPPER WHEEL HINGE
SQUARE SHAFT
P0636X067
P0636X068
PLN03M
SPECIAL WASHER 8MM
CAP SCREW M8-1.25 X 25
FLAT HD SCR M5-.8 X 16
LOCATE PLATE
LOCK NUT M6-1
PSB02M
CAP SCREW M6-1 X 20
KNOB
PFH39M
P0636X071
P0636X072
PFS07M
P0636X021
PSS75M
HEIGHT POINTER
SET SCREW M10-1.5 X 16
GUIDE BLOCK
FLANGE SCREW M5-.8 X 10
CAP SCREW M6-1 X 25
BLADE TENSION HANDLEWHEEL
LOWER WHEEL SUPPORT
FLAT WASHER 6MM
FLANGE SCREW M6-1 X 10
HEX BOLT M6-1 X 25
BRUSH
P0636X023
PSS07M
PSB06M
SET SCREW M5-.8 X 5
COMPRESSION SPRING
BUSHING
P0636X075
P0636X076
PW03M
P0636X025
P0636X026
P0636X027
P51201
PRESS BLOCK
PFS11M
THRUST BEARING 51201
BLADE TENSION SHAFT
TENSION LINE
PB10M
P0636X029
P0636X030
P0636X031
P0636XB032
P0636X080B
P0636XB081
PN04M
STEP COVER
UPPER WHEEL SHAFT
UPPER WHEEL ASSEMBLY
BUSHING
HEX NUT M4-.7
P0531B023
MAG BRAKE MOTOR 5HP 220V 1PH
MOTOR FAN COVER
MOTOR FAN
32-1 P0636X034
32-2 PR64M
94-2 P0531B023-2
94-3 P0531B023-3
94-4 P0531B023-4
94-5 P0531B023-5
94-6 P0531B023-6
94-7 P0531B023-7
94-8 P0531B023-8
94-9 P0531B023-9
94-10 P0531B023-10
94-11 P0531B023-11
94-12 P0531B023-12
94-13 PSB26M
INT RETAINING RING 72MM
BALL BEARING 6306ZZ
LOWER WHEEL
32-3 P6306
R. CAPACITOR COVER
S. CAPACITOR COVER
R. CAPACITOR 45M 450VAC
S. CAPACITOR 300MFD 250V
JUNCTION BOX
32-4 P0636X066
33
P0636XB033
LOWER WHEEL ASSEMBLY
BUSHING
33-1 P0636X034
33-2 PR64M
INT RETAINING RING 72MM
BALL BEARING 6306ZZ
LOWER WHEEL
33-3 P6306
CENTRIFUGAL SWITCH PLATE
CENTRIFUGAL SWITCH
MAGNETIC BRAKE
BRAKE SHOE
33-4 P0636X066
33-5 P0636XB033-5
33-6 PSBS22M
PULLEY
BUTTON HD CAP SCR M8-1.25 X 20
LOCK WASHER 8MM
UPPER WHEEL SLIDING BRACKET
COMPRESSION SPRING
GUIDE PIN 3 X 12
37
38
39
40
41
42
43
44
45
46
47
48
PLW04M
CAP SCREW M6-1 X 12
LOCK WASHER 6MM
KEY 5 X 5 X 25
P0636X038
P0636X039
P0636X040
P0636X041
P0636X042
PHTEK15M
PW05M
94-14 PLW03M
94-15 PK23M
94-16 PSB24M
CAP SCREW M5-.8 X 16
SET SCREW M6-1 X 6
ADJUSTMENT HUB COVER
BUTTON HD CAP SCR M8-1.25 X 20
HEX BOLT M10-1.5 X 35
CORD CLAMP 1/2"
MOVING PLATE
94-17 PSS02M
FIX PLATE
95
96
97
98
99
100
P0636X095
PSBS22M
PB14M
TAP SCREW M4 X 10
FLAT WASHER 4MM
TENSION POINTER
TAP SCREW M4 X 16
TENSION SCALE
P0636X045
PHTEK6M
P0636X047
P0636X048
P0636X098
PFS09M
FLANGE SCREW M5-.8 X 50
TERMINAL BOX
P0636X100
START SWITCH
Model g0636XB
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
main parts list continued
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
101
102
103
PS52M
PHLP HD SCR M4-.7 X 20
TERMINAL BLOCK
108
109
110
111
P0636X108
P0636X109
PW05M
PLATE
P0636X102
P0531B080
SWITCH CORD
MAGNETIC SWITCH MPE-18 22A
MAG SWITCH BACK COVER
FLAT WASHER 4MM
DOOR LATCH SWITCH ADZ-S11
103-1 P0531B080
P0636X111
103-2 P0531B080-1 CONTACTOR SDE MA-18 220V
103-3 P0531B080-2 RELAY SDE RA-30 (18-26)
103-4 P0531B080-3 MAG SWITCH FRONT COVER
103-5 P0531B080-4 CORD 0.75MM X 5C
111-1 P0636X111-1 DOOR LATCH
112
113
114
115
116
117
118
255
PFS10M
PS38M
FLANGE SCREW M4-.7 X 35
PHLP HD SCR M4-.7 X 10
P0636X114V2 UPPER WHEEL COVER V2.06.08
103-6 P0636XB103-6 POWER CORD 12AWG X 3C
103-7 P0636XB103-7 MOTOR CORD 12AWG X 5C
P0636X115
P0636X116
PHTEK15M
P0636X118
P0636X255
LOWER WHEEL COVER
SAW BLADE 3TPI 162" X 1" X 0.035
TAP SCREW M4 X 10
103-8 PFS07M
103-9 PFS07M
FLANGE SCREW M5-.8 X 10
RECTIFIER (PU-23-2)
CORD CLAMP 5/16"
107
P0636XB107
STRAIN RELIEF M13.5
EYE BOLT M10-1.5- X 15
-12-
Model g0636XB
Download from Www.Somanuals.com. All Manuals Search And Download.
table-fence-trunnion breakdown
Model g0636XB
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
table-fence-trunnion parts list
REF
19
PART #
PSB31M
DESCRIPTION
REF
PART #
DESCRIPTION
CAP SCREW M8-1.25 X 25
LOCK WASHER 8MM
FLAT WASHER 6MM
FLANGE SCREW M6-1 X 10
FLAT WASHER 8MM
LOCK WASHER 8MM
HEX BOLT M8-1.25 X 20
OUTER RAIL PLATE
CAP SCREW M6-1 X 10
LOCK WASHER 6MM
FLAT WASHER 6MM
SUPPORT PLATE
150-5
150-6
150-7
150-8
150-9
PFS17M
FLANGE SCREW M4-.7 X 8
37
PLW04M
PW03M
P0513X2B157-6 PIVOT BLOCK
PN03M HEX NUT M8-1.25
77
78
PFS11M
P0513X2B157-8 HANDLE
P0513X2B157-9 SHAFT
104
PW01M
105
PLW04M
PB09M
150-10 P0513X2B157-10 SPECIAL PLASTIC SET SCREW
150-11 P0513X2B157-11 NYLON PAD
106
120
P0636XB120
PSB04M
150-12 PSS14M
150-13 PN03M
150-14 PSB100M
150-15 PN03M
150-16 PW01M
SET SCREW M8-1.25 X 12
HEX NUT M8-1.25
121
122
PLW03M
PW03M
CAP SCREW M8-1.25 X 15
HEX NUT M8-1.25
123
124
P0636X222
PW03M
FLAT WASHER 8MM
125
FLAT WASHER 6MM
PROTECT COVER (ASM)
SLIDING PLATE
150-17 P0513X2B157-17 LOCK HANDLE M8-1.25 X 44
150-18 P0513X2B157-18 MOVING PLATE
126
P0636X224
P0636X225
P0636X226
P0636X227
PSB04M
127
151
PN09M
HEX NUT M12-1.75
HANDLE SHAFT
128
FIBER WASHER 13MM
SHOULDER SCREW
CAP SCREW M6-1 X 10
LOCK WASHER 6MM
FLAT WASHER 6MM
HEX BOLT M8-1.25 X 55
FLAT WASHER 8MM
SLIDING PLATE
152
P0636X152
P0636X153
P0636X155
PS38M
129
153
HANDLE KNOB M12-1.75 (FEMALE)
POINTER
130
155
131
PLW03M
PW03M
156
PHLP HD SCR M4-.7 X 10
TABLE
132
159
P0636X159
P0636XB160
133
PB30M
160
MITER GAUGE ASSEMBLY
134
PW01M
160-1
160-2
160-3
160-4
160-5
160-6
160-7
160-8
160-9
P0513X2B152-1 GUIDE BAR
P0513X2B152-2 GUIDE PIECE
135
P0636X233
PLN04M
136
LOCK NUT M8-1.25
PFH04M
FLAT HD SCR M6-1 X 8
137
P0636X137
P0636X138
PW01M
GUARD RAIL
P0513X2B152-4 POINTER
138
GUARD RAIL PLATE
FLAT WASHER 8MM
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 20
CAP SCREW M10-1.5 X 30
LOCK WASHER 10MM
FLAT WASHER 10MM
FLANGE SCREW M6-1 X 10
BLADE GUARD
PS06
PHLP HD SCR 10-24 X 3/8
139
P0513X2B152-6 SHOULDER SCREW
P0513X2B152-7 MITER GAUGE BODY
140
PLW04M
PSB14M
141
PW01M
FLAT WASHER 8MM
142
PSB72M
P0513X2B152-9 HANDLE
143
PLW06M
PW04M
160-10 P0513X2B152-10 FIXED BLOCK
160-11 P0513X2B152-11 LOCKING SHAFT
144
145
PFS11M
160-12 PS06
160-13 PN04M
160-14 PS56M
PHLP HD SCR 10-24 X 3/8
146
P0636X146
PSB84M
HEX NUT M4-.7
147
CAP SCREW M10-1.5 X 35
TRUNNION BRACKET ASSEMBLY
PRESS SHAFT
PHLP HD SCR M4-.7 X 16
148
P0636XB148
P0566168
P0636X149
PSB14M
160-15 P0513X2B152-15 SCALE
148-1
148-2
148-3
148-4
148-5
148-6
148-7
149
161
P0636X161
P0636X164
PSB06M
TABLE INSERT
MICRO ADJUSTING RING
CAP SCREW M8-1.25 X 20
LOCK WASHER 8MM
TRUNNION BLOCK
164
HANDLE 3/8-16 X 1/2
CAP SCREW M6-1 X 25
HANDWHEEL 7" (STEEL)
GUIDE BRACKET ASSEMBLY
GUIDE BRACKET
165
PLW04M
P0566177
P0566178
P0636X154
P0513X2B156
166
P0636X166
P0636XB167
P0566198
P0566196
PN05M
167
PRESS BLOCK
167-1
167-2
167-3
167-4
167-5
167-6
167-7
167-8
167-9
TRUNNION HOUSING
RESAW FENCE ASSEMBLY
WORM SHAFT
HEX NUT M16-1.5
149-1
149-2
149-3
150
P0513X2B156-1 RESAW FENCE(AL) 590MM
P0566201
P0566202
PSS07M
BUSHING
P0636X122
P0636X123
P0513X2B157
TAP SCREW 3.5 X 8
SWITCH BUSHING
SET SCREW M5-.8 X 5
HEX NUT M5-.8
FENCE PIECE 148 X 22 X 1
FENCE ASSSMBLY
PN06M
150-1
150-2
150-3
150-4
P0513X2B157-1 FENCE
P0513X2B157-2 POINTER
PLW04M
PSB11M
LOCK WASHER 8MM
CAP SCREW M8-1.25 X 16
FLANGE SCREW M5-.8 X 10
COVER
PSS09M
SET SCREW M8-1.25 X 20
167-10 PFS07M
167-11 P0566187
P0513X2B157-4 SPRING PIECE
-14-
Model g0636XB
Download from Www.Somanuals.com. All Manuals Search And Download.
REF
PART #
DESCRIPTION
REF
PART #
DESCRIPTION
167-12 P0566192
COVER
169-8 PR03M
EXT RETAINING RING 12MM
BALL BEARING 6201ZZ
UPPER SPACING SLEEVE
SHAFT
167-13 P0636XB167-13 FIXED BOLT
169-9 P6201
167-14 P0566191
167-15 PFH19M
167-16 P0566207
167-17 P0566206
167-20 P0566194
167-21 P0566195
EXTENSION RACK
169-10 P0636X249
169-11 P0636X250
169-12 P0636X184
169-13 PB04M
FLAT HD SCR M4-.7 X 10
RACK
UPPER GUIDE SUPPORT BLOCK
HEX BOLT M6-1 X 10
BUTTON HD CAP SCR M8-1.25 X 35
FLAT WASHER 8MM
UPPER GUIDE BAR
PINION GEAR
170
171
172
PSBS04M
PW01M
FIXED PLATE
168
P0636XB168
UPPER GUIDE ASSEMBLY
SWITCH BUSHING
SET SCREW M5-.8 X 5
BUSHING
P0636XB172
LOWER BLADE GUIDE ASSEMBLY
HEX BOLT M6-1 X 16
ECCENTRIC SHAFT
168-1 P0636X167
168-2 PSS07M
168-3 P0636X169
168-4 P0636X172
168-5 PN05M
172-1 PB83M
172-2 P0636X242
172-3 PR05M
EXT RETAINING RING 15MM
BALL BEARING 6202ZZ
HANDLE BUSHING
UPPER GUIDE BRACKET
HEX NUT M16-1.5
WORM SHAFT
172-4 P6202
172-5 P0636X245
172-6 PSB29M
172-7 PR03M
168-6 P0636X174
168-7 P0636X175
168-8 P0636X176
168-9 P0636X177
168-10 P0636X178
168-11 PLW04M
168-12 PB06M
CAP SCREW M6-1 X 40
EXT RETAINING RING 12MM
BALL BEARING 6201ZZ
UPPER SPACING SLEEVE
UPPER BLADE GUIDE SUPPORT
SHAFT
WORM GEAR
FIXED PLATE
172-8 P6201
FIXED BOLT
172-9 P0636X249
172-10 P0636X240
172-11 P0636X239
172-12 P0636X238
172-13 PB83M
COVER
LOCK WASHER 8MM
HEX BOLT M8-1.25 X 12
FLAT HD SCR M4-.7 X 10
RACK
LOWER SUPPORT BRACKET
HEX BOLT M6-1 X 16
HANDWHEEL 6-1/2" (PLASTIC)
HEX BOLT M8-1.25 X 50
FLAT WASHER 8MM
168-13 PFH19M
168-14 P0636X182
168-15 P0636X183
168-16 P0636X186
168-17 PN04M
173
174
175
176
177
181
182
183
184
251
252
253
254
P0636XB173
PB166M
EXTENSION RACK
UPPER GUIDE BAR
HEX NUT M4-.7
PW01M
PN03M
HEX NUT M8-1.25
168-18 PS38M
PHLP HD SCR M4-.7 X 10
CAP SCREW M6-1 X 16
UPPER BLADE GUIDE ASSEMBLY
UPPER BLADE GUIDE SUPPORT
HEX BOLT M6-1 X 16
ECCENTRIC SHAFT
EXT RETAINING RING 15MM
BALL BEARING 6202ZZ
HANDLE BUSHING
CAP SCREW M6-1 X 40
P0636XB177
P0636XB181
PLW03M
PW03M
SUPPORT PLATE
168-19 PSB01M
STOP BRACKET
169
P0636XB169
LOCK WASHER 6MM
FLAT WASHER 6MM
169-1 P0636X240
169-2 PB83M
PB83M
HEX BOLT M6-1 X 16
WRENCH 10/13
169-3 P0636X242
169-4 PR05M
PWR1013
PWR1719
PAW05M
PAW06M
WRENCH 17/19
169-5 P6202
HEX WRENCH 5MM
169-6 P0636X245
169-7 PSB29M
HEX WRENCH 6MM
Model g0636XB
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
labels breakdown
(&,
(%%
(&&ꢀ
(&'
(%,
(&-
(&%
(%&
(%'
(%(
(%)
('%
(%.
(%-
(&(
(&)
(&+
(&.
(%)
(%*
(%,
(%+
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
P0636X310 BLADE ASSEMBLY DIRECTION LABEL
G8589 GRIZZLY NAMEPLATE-LARGE
300
301
302
303
304
305
306
307
308
309
P0636XB300 MODEL NUMBER LABEL
P0636XB301 MACHINE ID LABEL
PLABEL-11 SAFETY GLASSES LABEL
PLABEL-12 READ MANUAL LABEL
PLABEL-14 ELECTRICITY LABEL
310
311
312
313
314
316
317
318
319
320
P0636X312 TENSION ADJ LABEL
P0636X313 TABLE ANGLE SCALE
P0636X314 TABLE LOCK LEVER LABEL
P0636X316B MOTOR LABEL
PPAINT-1
GRIZZLY GREEN PAINT
PPAINT-11 GREY PUTTY TOUCH UP PAINT
P0636X317 UPPER WHEEL HINGE/STOP BOLT LABEL
P0636X318 PATENT LABEL
PLABEL-20 DONT OPEN LABEL 2"W X 3 5/16"H
PLABEL-19 HANDS/BS BLADE LABEL 2" X 3 5/16"H
PLABEL-18 UNPLUG BANDSAW LABEL 2" X 3 5/16"H
P0566313
TABLE LOCK LABEL
P0636XB320 MAGNETIC BRAKE NOTICE
safety labels warn about machine hazards and ways to prevent injury. the owner of this machine
must maintain the original location and readability of the labels on the machine. if any label is
removed or becomes unreadable, replace that label before using the machine again. contact
grizzly at (800) 523-4777 or www.grizzly.com to order new labels.
-16-
Model g0636XB
Download from Www.Somanuals.com. All Manuals Search And Download.
|