FOLDING SIDES GARDEN
WAGON
MODEL H0771
INSTRUCTION SHEET
COPYRIGHT © MARCH, 2004 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#6143 PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
REMOVAL & INVENTORY
1. Remove your new wagon from the carton.
2. Make sure all parts are present and in good
condition.
FRONT SUPPORT ASSEMBLY
1. Insert the yoke into the front axle support
by sliding the top hole of the yoke onto the
pivot post on the front axle support. Place
the 10mm flat washer on the pivot post and
slide the cotter pin in the pre drilled hole and
spread. Bolt the center front axle brace and
yoke to the bottom of the front axle support
with the M8-1.25 x 17 shoulder bolt, 6mm flat
washer and lock nut. See Figure 1
Figure 2. Rear and front axle assemblies
4. Slide a wheel spacer bushing, part 22, on
each axle.
Front axle
support
5. Slide a wheel onto each axle with the valve
stems to the outside and fasten using the
M12-1.75 acorn nuts, 12mm flat washers
and lock washers.
Center front
axle brace
Yoke
FOLDING SIDES
1. Using the panel assembly pins, fasten the
hinges of the side panels to the bed, with the
side panel hinges on the outside.
2. Fasten the hinges of the front panel to the
end with the front axle assembly using the
panel assembly pins.
3. Fasten the hinges of the back panel to the
end with the rear axle support using the
panel assembly pins.
Steering
Connector
Figure 1. Front axle assembly detail.
2. Bolt the steering connector to the steering
arms of the front axle support and the yoke
using M8-1.25 x 15 shoulder bolts, 6mm flat
washers and lock nuts.
3. Mount the front axle assembly to the end
of the bed with the corresponding bolt pat-
tern using M8-1.25 x 20 carriage bolts, 8mm
washers and lock nuts.
PULL HANDLE
1. Slide the plastic coupling on to the pull
handle, making sure the holes are correctly
aligned.
2. Place the pull handle and plastic coupling
into the yoke and insert the M8-1.25 x 80
slotted screw. Fasten using an 8mm washer
and lock nut.
Note—The Folding Sides Garden Wagon comes
equipped with a tractor connector. Slide
the tractor connector over the handle of the
wagon and connect to the tractor hitch.
REAR SUPPORT ASSEMBLY & WHEELS
1. Loosely assemble the rear axle support to the
bed using M8-1.25 x 20 carriage bolts, 8mm
washers and lock nuts.
2. Slide the left and right rear axle braces onto
the rear axles and bolt the opposite ends of
the braces to the bed using M8-1.25 x 20 car-
riage bolts, 8mm washers and lock nuts. See
Figure 2
If you need additional help with this procedure,
call our service department at: (570) 546-9663.
3. Tighten the rear axle support.
Download from Www.Somanuals.com. All Manuals Search And Download.
H0771 Parts Breakdown and List
4
2
1
25
16
3
2
19
20
21
8
6
32
15
7
9
10
27
12
30
31
21
20
28
22
14
18
11
13
24
26
23
33
DESCRIPTION
5
REF
15 PW04M
PART#
DESCRIPTION
FLAT WASHER 10MM
REF
1
PART#
16 PH0771016 PANEL ASSEMBLY PINS
18 PW06M FLAT WASHER 12MM
19 PH0771019 MALE LOCK HANDLE M8-1.25
PH0771001
PH0771002
PH0771003
PH0771004
PH0771005
PH0771006
PH0771007
PH0771008
PH0771009
PH0771010
PH0771011
PH0771012
PH0771013
PH0771014
BED PANEL
2
SIDE PANEL
FRONT PANEL
BACK PANEL
3
20 PW01M
21 PLN04M
FLAT WASHER 8MM
LOCK NUT M8-1.25
4
5
WHEEL 13" X 5.00-6
REAR AXLE SUPPORT
22 PH0771022 WHEEL SPACER BUSHING
6
23 PN26M
24 PLW05M
25 PCB01M
ACORN NUT M12-1.75
7
LEFT REAR AXLE BRACE
RIGHT REAR AXLE BRACE
FRONT AXLE SUPPORT
CNTR FRONT AXLE BRACE
YOKE
LOCK WASHER 12MM
8
CARRIAGE BOLT M8-1.25 x 20
9
26 PH0771026 SLOT SCREW M8-1.25 x 80
27 PH0771027 SHLDR BOLT M8-1.25 x 15
28 PH0771028 SHLDR BOLT M8-1.25 x 17
10
11
12
13
14
STEERING CONNECTOR
PLASTIC COUPLING
PULL HANDLE
30 PW03M
31 PLN03M
FLAT WASHER 6MM
LOCK NUT M6-1.0
32 PH0771032 COTTER PIN
14-1 PH0771014-1 PAD (LOWER)
14-2 PH0771014-2 PAD (UPPER)
33 PH0771033 TRACTOR CONNECTOR
Download from Www.Somanuals.com. All Manuals Search And Download.
|