Model H8095
1500 LB
Steel ATV Jack
Operation
Pump Handle (Figure 1): To raise the jack, rotate
the pump handle clockwise completely, then move
the pump handle up and down. To lower the jack,
slowly rotate the pump handle counterclockwise.
Failure to follow these instructions could
result in serious personal injury or death:
1. DO NOT overload this jack beyond its
rated capacity. Overloading can cause
the jack to collapse and drop the load.
2. ALWAYS support the vehicle withappro-
priately rated support stands before
working under it.
Lock Release Pedal (Figure 1): This jack fea-
tures a stepped lock system that prevents loads
placed on the jack from accidentally dropping.
When pushed down, the lock release pedal allows
the operator to completely lower the jack and
bypass the stepped lock system.
3. DO NOT attempt to move the vehicle
while the jack is in use.
4. Use only on hard level surfaces like
concrete or asphalt. Other surfaces are
potentially unstable.
Note: The lock pedal will not release if the load
binds against the stepped plate. To remove a
bind, jack the load one or two pumps.
5. Center the load on the jack to maintain
proper balance and stability.
6. DO NOT use jack if it begins leaking
fluid or if it slowly sinks with a heavy
load. These are indications that the jack
needs to be immediately serviced.
Pump
Handle
Specifications
Maximum Lifting Capacity .................. 1,500 Lbs.
Lifting Range .............................................6"–18"
Weight ..................................................... 78 Lbs.
Lock
Release
Pedal
Figure 1. Jack controls.
If you need help with the Model H8095, call our
Technical Support line at: (570) 546-9663.
COPYRIGHT © DECEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR8826 PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
H8095 Parts Breakdown and List
��
��
��
��
��
��
��
��
��
��
��
��
�
��
��
��
��
�
��
��
��
��
��
��
��
��
��
��
��
�
�
��
��
��
�
��
��
��
��
�
�
�
�
��
��
��
�
��
��
�
��
�
��
��
��
�
�
�
�
�
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PR06M
PW08M
EXT RETAINING RING 16MM
FLAT WASHER 16MM
FRONT WHEEL
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
PH8095021
PH8095022
PR01M
REAR CASTER
2
FLANGE BOLT M10-1.5 X 20
EXT RETAINING RING 10MM
EXT RETAINING RING 20MM
PEDAL ASSEMBLY
LIFTING ARM FIXING POLE
SOCKET BOLT
3
PH8095003
PH8095004
PH8095005
PH8095006
PH8095007
PH8095008
PN13M
4
BASE ASSEMBLY
PLASTIC END CAP
SADDLE ASSEMBLY
RUBBER CUSHION
POLE
PR09M
5
PH8095025
PH8095026
PH8095027
PLW07M
6
7
8
LOCK WASHER 20MM
LOCK NUT M12-1.75
FIXING PIPE
9
HEX NUT M16-2
PLN09M
10
11
12
13
14
15
16
17
18
19
20
PH8095010
PH8095011
PLW10M
BUSHING
PH8095030
PH8095031
PR39M
RATCHET PLATE
LOCK WASHER 16MM
AXLE COVER
HANDLE SOCKET
EXT RETAINING RING 8MM
PRESS WHEEL
PH8095013
PH8095014
PR07M
PH8095033
PH8095034
PB09M
SAFETY AXLE
PRESS WHEEL SHAFT
HEX BOLT M8-1.25 X 20
PUMP ASSEMBLY
EXT RETAINING RING 18MM
EXT RETAINING RING 14MM
SADDLE FIXING AXLE
HEX BOLT M8-1.25 X 12
FLAT WASHER 8MM
LIFTING ARM
PR02M
PH8095036
PH8095037
PH8095038
PH8095039
PH8095017
PB06M
HANDLE
MACHINE ID LABEL
FILL PLUG
PW01M
PH8095020
The machine ID label warns about hazards and ways to prevent injury. The owner of the jack
MUST maintain the original location and readability of the label. If the label is removed or becomes
Download from Www.Somanuals.com. All Manuals Search And Download.
�����������������������������������������������������������������������
�������������������������������������
������������������������������������
�����������������
��������������������������������
���������������������������������
����
�����������������
����
������������������
Download from Www.Somanuals.com. All Manuals Search And Download.
|