model h8234
28° framing nailer
oWner's manual
COPYRIGHT © AUGUST, 2007 BY GRIZZLY INDUSTRIAL, INC.
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
#TS9831 PRINTeD IN CHINA ReVISeD JULY, 2008 (TR)
Download from Www.Somanuals.com. All Manuals Search And Download.
safety
for your own safety read instruction manual
before operating this equipment
the purpose of safety symbols is to attract your attention to possible hazardous
conditions. this manual uses a series of symbols and signal words which
are intended to convey the level of importance of the safety messages. the
progression of symbols is described below. remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
indicates an imminently hazardous situation which,
if not avoided, Will result in death or serious injury.
indicates a potentially hazardous situation which, if
not avoided, could result in death or serious injury.
indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
it may also be used to alert against unsafe practices.
this symbol is used to alert the user to useful
NOTICE
information about proper operation of the equipment.
safety instructions for pneumatic tools
5. Keep children and visitors
aWay. All children and visitors
should be kept at a safe distance
from work area.
1. Keep all safety devices in
place and in working order.
2. remove adJusting Keys and
Wrenches. Form habit of check-
ing to see that keys and adjusting
wrenches are removed from tool
before operation.
6. maKe WorKshop child proof
by locking your shop and shutting off
air valves.
7. do not force tool. It will do
the job better and safer at the rate for
which it was designed.
3. Keep WorK area clean.
Cluttered areas and benches invite
accidents.
8. use the right tool. Do not
force tool or attachment to do a job
for which it was not designed.
4. do not use in dangerous
environment. Do not use pneu-
matic tools in damp or wet locations,
or where any flammable or noxious
fumes may exist. Keep work area
well lighted.
9. do not use under the
influence of drugs or
alcohol.
-1-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
safety instructions for pneumatic tools
17. disconnect tools before ser-
vicing, changing accessories, or
moving to another location.
10. use proper air hose for the
tool. Make sure your air hose is in
good condition and is long enough
to reach your work without stretch-
ing.
18. do not overreach. Keep
proper footing/balance at all times.
11. Wear proper apparel. Do
not wear loose clothing, gloves,
neckties, rings, bracelets, or other
jewelry which may get caught in
moving parts. Non-slip footwear is
recommended. Wear a protective
hair covering to contain long hair.
19. use
the
recommended
accessories. Consult owner’s
manual for recommended acces-
sories. The use of improper acces-
sories may cause risk of injury.
20. checK for damaged parts
before using. Check for bind-
ing and alignment of parts, broken
parts, part mounting, loose bolts,
and any other conditions that may
affect machine operation. Repair or
replace damaged parts.
12. alWaysusesafetyglasses.
Also use a face or dust mask if cut-
ting operation is dusty. everyday
eyeglasses only have impact resis-
tant lenses, they are NOT safety
glasses.
21. never leave unattended
tool connected to air.
Disconnect the air hose and do not
leave tool until it is relieved of any
built up pressure.
13. Wear approved hearing
protection. Air escaping from
pneumatic tools can exceed safe
exposure limits and may cause
hearing damage with prolonged
exposure.
22. never alloW untrained
users to use this tool
While unsupervised.
14. secure WorK. Use clamps or a
vise to hold work when practical. It
is safer than using your hand and
frees both hands to operate tool.
23. if you are unsure of the
intended operation, stop
using tool. Seek formal training
or research books or magazines
that specialize in pneumatic tools.
15. maintain tools With care.
Keep tools lubricated and clean
for best and safest performance.
Follow instructions for lubricating
and changing accessories.
24. be aWare of hose location
When
using
pneumatic
tools. Hoses can easily become
a tripping hazard when laid across
the floor or spread out in a disorga-
nized fashion.
16. reduce
the
risK
of
unintentional firing. Do not
carry tool with hand on trigger and
always disconnect from air when
not in use.
-2-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
additional safety instructions for nailers
1. hand inJuries: Do not place your
hands near the nail point of entry. A
nail can deflect and tear through the
surface of the workpiece, puncturing
your hand or fingers.
6. hose usage: Make sure your air
hose is designed for the tool in use, is
in good condition, and is long enough
to reach your work without stretching.
However, an overly long air hose in
the work area may be a tripping haz-
ard.
7. operating Questions: If you
are not sure about the intended oper-
ation, stop using the nailer. Seek
formal training.
8. cleaning: Never use gasoline or
other flammable liquids to clean the
nailer; vapors in the nailer will ignite
by a spark and cause it to explode.
9. maintenance: Always disconnect
air from the nailer when servicing or
installing nails. During maintenance,
a nailer connected to air may fire acci-
dentally, causing serious personal
injury.
2. combustible gases: Never con-
nect the nailer to pressurized oxy-
gen or other combustible gases as a
power source. Only use filtered, lubri-
cated, and regulated compressed air.
3. safe handling: Never point the
nailer at others! Do not keep the trig-
ger pulled when loading fasteners,
carrying, or holding tool. Carry the
nailer only by the handle, never by
any other part. Do not carry the nailer
by the air hose. Disconnect the nailer
from the air hose when going up and
down ladders.
4. modifications: DO NOT modify
this tool or bypass the safety nose
mechanism.
5. checK valve: Do not use a check
valve or any other fitting that allows
air to remain in the tool.
10. compressed air rating: Do
not connect the nailer to compressed
air that exceeds 120 PSI.
-3-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
never point this nailer at yourself or
another person! always pay attention
to the direction this nailer is pointed.
use this tool with respect and caution
to lessen the possibility of operator or
bystander injury. ignoring this warn-
ing may result in serious personal
injury.
read the manual before operation.
become familiar with this nailer, its
safety instructions, and its operation
before beginning any work. serious
personal injury may result if safety or
operational information is not under-
stood or followed.
nailer accidents routinely happen
while moving the gun to another
location, such as up ladders, to
another room, or even another job
site. always disconnect the gun
immediately after use and never
transport the gun while connected to
the air—even if the air compressor is
disconnected from its power source!
no list of safety guidelines can be
complete. every shop environment
is different. always consider safety
first, as it applies to your individu-
al working conditions. use this and
other tools with caution and respect.
failure to do so could result in seri-
ous personal injury, damage to equip-
ment or poor work results.
operating this nailer can propel
objects into the air, causing imme-
diate eye damage. to protect your-
self, always wear american national
standards institute (ansi) approved
safety glasses or goggles when oper-
ating this equipment. in addition, this
nailer discharges at up to 85-90 deci-
bels. to protect your hearing, always
wear ansi approved ear protection
when operating this nailer.
-4-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
introduction
foreword
contact info
We are proud to offer the Grizzly Model
H8234 28° Framing Nailer. This model
is part of a growing Grizzly family of fine
pneumatic tools. When used according to
the guidelines set forth in this manual, you
can expect years of trouble-free, enjoyable
operation and proof of Grizzly’s commit-
ment to customer satisfaction.
If you have any comments regarding this
manual, please contact us:
Grizzly Industrial, Inc.
C/O Technical Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
email: [email protected]
The specifications, details, and photo-
graphs in this manual represent the Model
H8234 as supplied when the manual was
prepared. However, owing to Grizzly’s pol-
icy of continuous improvement, changes
may be made at any time with no obliga-
tion on the part of Grizzly.
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
tool data
Nail Size ...................... 1⁄8" Shank Diameter
Nail Strip Angle...............28º Clipped Head
Nail Length .......................................2"-3½"
Magazine Capacity.................. 2 x 25 Nails
Air Inlet ...........................................¼" NPT
Weight ............................................ 83⁄4 lbs.
Operating Pressure .................. 80-110 PSI
Maximum Air Pressure.................. 120 PSI
-5-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
set up
unpacking
inventory
Your new nailer was carefully packaged for
safe shipping. If you discover any damage
after you have signed for delivery, immedi-
ately call Customer Service at (570) 546-
9663 for advice.
After you open the nailer box, you should
find the following.
model h8234 inventory (figure 1)
Qty
a. 28° Framing Nailer............................. 1
b. Safety Goggles ................................. 1
c. Oil....................................................... 1
d. Hex Wrench Set (3–6mm) ................. 1
e. Carrying Case.................................... 1
Save the containers and all packing mate-
rials for possible inspection by the car-
rier or its agent. Otherwise, filing a freight
claim can be difficult.
When you are completely satisfied with
the condition of the shipment, you should
inventory the contents.
A
B
D
C
e
figure 1. Model H8234 inventory.
-6-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
compressed air
system
The Model H8234 is designed to be oper-
ated at 80-110 PSI using clean, dry, regu-
lated, compressed air. do not exceed
the 120 psi maximum operating pres-
sure for your model.
Before using your new nailer, regulate the
air pressure to find the optimum setting
within the specified operating range. Start
by testing the nailer at a low setting, then
increase the air pressure as needed for
satisfactory results.
exceeding the maximum permissible
operating pressure may damage the
nailer and cause it to malfunction. to
protect yourself from personal injury,
do not allow the air pressure to
exceed the recommended pressure
for this nailer!
An in-line filter/lubricator/regulator unit can
be installed, as depicted in figure 2.
Check the current Grizzly catalog for avail-
ability of this unit. If you plan on install-
ing a filter/lubricator/regulator unit in your
compressed air system, always follow the
connection instructions that come with
the unit.
This filter/lubricator/regulator unit will
protect your tool from damaging water
build-up, allow you to adjust and maintain
constant air pressure to your tool, and
save you the inconvenience of having to
manually lubricate your tool every time
you use it.
Quick
Connector
Quick
Connector
Lubricator
Regulator
Your
Tool
Air
Compressor
Quick
Coupler
Quick
Coupler
Air Hose
Filter
figure 2. Typical filter/lubricator/regulator installation order.
-7-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Without pressing the trigger, depress
the safety nose mechanism against a
scrap piece of wood that is clean and
free of any knots, nails, or other foreign
objects.
safety nose
mechanism
A safety mechanism (bump fire) on the
nose of the nailer protects against acci-
dental firing. When the trigger is pressed,
the nailer will not fire until the safety nose
mechanism is depressed.
— If the nailer does not fire, then the
safety nose mechanism is working
correctly.
— If the nailer does fire when you
do this, immediately disconnect the
nailer from the air supply and call
Grizzly Technical Support at (570)
546-9663 for help.
Before you use your nailer for the first
time, check the safety nose mechanism to
ensure proper function.
to check the safety nose mechanism:
— If the nailer does fire when the
trigger is pulled, without the safety
nose mechanism being depressed,
then the nailer is not working
properly.
1. DISCONNeCT NAILeR FROM THe
AIR SUPPLY!
2. Make sure the magazine is empty and
contains no nails.
— If you find that the safety nose
mechanism is not depressing
properly, check the lubrication of its
sliding components.
3. Make sure the trigger and the safety
nose mechanism move up and down
without sticking.
4. Connect the nailer to the air supply.
do not attempt to modify or bypass
the safety nose mechanism to make
the nailer fire without pushing the
safety nose down.
the safety mechanism is a mechanical
device that can fail. never rely on this
mechanism as an excuse to point the
nailer at yourself or any bystanders.
serious injury may occur.
-8-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
operations
loading
When replacing nails in your model
h8234, follow these guidelines:
Nail Size ...................... 1⁄8" Shank Diameter
Nail Strip Angle...............28º Clipped Head
Length..............................................2"–31⁄2
"
Magazine Capacity.................. 2 x 25 Nails
figure 4. Loading nails into magazine.
to load your nailer:
4. Tilt the nailer to slide the nails all the
way down to the nose.
1. DISCONNeCT NAILeR FROM THe
AIR SUPPLY!
5. With one hand on the magazine pusher
for control, release the magazine catch
and slowly allow the pusher to press
against the nails.
2. Grip the nailer firmly, and pull the
magazine pusher back until the catch
lever engages, as shown in figure 3.
operating
if you have not read the safety instruc-
tions in this manual, do not operate the
nailer.
Before you operate your nailer, place five
to six drops of the included oil into the
quick connect fitting where the nailer con-
nects to the air supply.
Pusher
figure 3. Sliding magazine pusher back
and engaging catch lever.
to operate your nailer:
3. Insert a strip of nails, pointed-end
down, into the magazine as shown in
figure 4.
1. Connect the air supply to the quick con-
nect fitting.
2. To test for proper nail penetration, hold
the nailer perpendicular to the surface
of a piece of clean scrap wood that is
thick enough for the length of nails you
have loaded.
-9-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Depress the safety nose mechanism
against your workpiece.
adjusting depth
4. Before pulling the trigger, make sure
your free hand and other body parts
are positioned out of the way of a
potential path of a nail in case of deflec-
tion.
The depth of nail penetration is adjusted
with the cap screw that secures the safety
nose.
to adjust the depth:
Deflection is caused when grain
irregularities, knots, or foreign
objects inside the wood cause the
nail to change its path, resulting in
the nail puncturing the surface of the
workpiece, as shown in figure 5.
1. DISCONNeCT NAILeR FROM THe
AIR SUPPLY!
2. Using a 4mm hex wrench, loosen the
cap screw shown in figure 6.
3. Move the safety nose away from the
nailer to decrease nail depth, and
toward the nailer to increase nail
depth.
Besides damaging your workpiece,
deflection can cause injury if your free
hand is securing the workpiece in the
location that the nail deflects.
Safety Nose
Cap Screw
figure 6. Loosening cap screw for depth
adjustment.
figure 5. example of nail deflection.
5. Pull the trigger.
4. Re-tighten the cap screw, then connect
the nailer to the air supply and test the
nail depth.
— If the nail drove into the wood far
enough, continue with your intended
operations.
5. Repeat steps 2–4, if necessary, until
the nail depth is satisfactory.
— If the nail either went too far or not
far enough, then go to the adjusting
depth section on this page.
-10-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
clearing Jammed
nails
A jammed nail must be cleared before
using the nailer again.
Nose Opening
to clear a jammed nail from the dis-
charge area:
figure 7. Nose opening for clearing a
jammed nail.
1. DISCONNeCT NAILeR FROM THe
AIR SUPPLY!
5. Dislodge the jammed nail with a tool
that will fit in the slot on the underside
of the nose.
2. Pull back and latch the magazine push-
er.
6. Throw the damaged nail away and
insert a new nail stick that only contains
clean, undamaged nails. DO NOT use
dirty or damaged nails!
3. Remove the nail stick from the maga-
zine.
4. Locate the opening in the underside of
the nailer safety nose (see figure 7).
7. Release the catch lever and slowly
let the pusher slide to the front of the
magazine.
-11-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Watch the discharge area and push the
top of the piston with your finger. You
will see the piston shaft slide down the
discharge area.
replacing pistons/o-
rings
Under heavy use, a piston, piston shaft,
or O-ring may wear out. Replacement
is quick and easy. Contact Grizzly
Customer Service at (800) 523-4777 to
obtain the Piston Repair Kit (Part Number
PH8234092), or the complete O-Ring
Repair Kit (Part Number PH8234093).
7. Taking care not to scratch or dent the
nailer parts, use a wooden dowel or
similarly shaped tool to push the piston
shaft back inside the nailer until you
can grip the piston head and remove
it from the cylinder. Clean and inspect
the parts for cracks, wear, or burrs.
8. Place a new O-ring on the new piston
and apply a thin film of the nailer lubri-
cating oil on the O-ring.
9. Insert the new piston in the cylinder.
Make sure that the grooves on the pis-
ton shaft line up with those on the guide
at the bottom of the cylinder. The new
piston should easily slide into the cyl-
inder. do not force the piston into
the cylinder! If the piston is not easily
inserted, double-check the alignment of
the piston shaft with the grooves on the
guide.
always disconnect air from nailer
whenever servicing! during mainte-
nance, a nailer connected to air may
fire accidentally, causing serious per-
sonal injury!
10. After the piston is inserted correctly,
close the magazine. Replace the rear
cap assembly and tighten the 4 cap
screws.
to replace a piston:
1. DISCONNeCT NAILeR FROM THe
AIR SUPPLY!
note: For more assistance, or to install
a complete O-ring set, refer to the
appropriate breakdown diagram in the
back of this manual for component
locations.
2. Remove all nails from the magazine
cartridge, and clean the exterior of the
nailer.
3. Remove the four cap screws on the
back of the nailer, near the exhaust
port.
4. Remove the cap.
5. The top of the piston should now be
visible inside the cylinder, which is
housed in the head of the nailer.
-12-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
accessories
h3175—1⁄4" npt female, Quick coupler
g8114—3⁄8" x 25 ft. air hose
h3176—1⁄4" npt male, Quick coupler
h3177—1⁄4" npt male, plug
g8115—3⁄8" x 50 ft. air hose
g8116—3⁄8" x 100 ft. air hose
Multi-purpose red rubber air hose is flex-
ible and abrasion resistant. Rated for 200
h3178—1⁄4" npt female, plug
PSI, this air hose has a bursting strength
H3175
H3176
H3177
1
of 800 PSI
⁄4" NPT ends.
H3177
figure 8. 1⁄4" NPT air fittings.
3
h3258—filter/lube/regulator ⁄8"npt
h3259—filter/lube/regulator ⁄2"npt
1
figure 10. Red rubber air hose.
These units are indispensable for prolong-
ing the lifespan of your air tools. Filter
keeps water/rust out. Lubricator features
adjustable automatic lubrication. Regulator
allows you to control the optimum PSI
delivery for each air tool. Maximum pres-
sure for each unit is 150 PSI.
h3275—1⁄4" x 25' recoil air hose
h3275—1⁄4" x 50' recoil air hose
These recoil air hoses are ideal for nail-
ers and staplers because they are light
weight and offer maneuverability in tight
places that is unmatched by rubber hoses.
Coiled springs protect the ends from kink-
ing. (Prices are less than you'll spend on
lunch!)
H3258
H3259
figure 9. Models H3258 & H3259
FilterLubricator/Regulators.
figure 11. Recoil air hose.
g2820—pneumatic tool oil 8 oz.
g2821—pneumatic tool oil 1 pint
Use the right oil! This pneumatic tool oil
offers outstanding heat displacement and
friction reduction without eating away at
delicate air components like detergent
motor oils. Stock up with extra bottles to
avoid costly downtime.
-13-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
cleaning & lubrication
cleaning
lubricating
Use non-flammable solvent to clean the
nose assembly of the nailer. Always be
sure that the nailer is dry before using it
again.
Standard pneumatic tool oil has been
included with your new Grizzly nailer to
help maintain its useful life. Place two to
six drops of oil in the nailer air inlet (as
shown in figure 12) before every use, or
after 2 hours of continuous use.
Do not allow dust, chips, sand, etc. into
the air connectors or into the body of the
nailer; this may result in leaks and damage
to the nailer and the air couplings.
Wipe off any excess oil near the nailer
exhaust to avoid dust build-up. When the
oil that was included with the nailer has
been completely used, replace with Grizzly
Model G2820 Pneumatic Tool Oil.
Another option to manual oiling would be
to install a lubricator in your air compres-
sor line. If your air compressor line already
has a lubricator, then regular lubrication
of your nailer will not be necessary. Just
make sure there is always oil in the lubri-
cator.
never clean this tool with gasoline
or other flammable liquids. vapors
in the tool may ignite, causing the
tool to explode. ignoring this warning
may lead to serious personal injury or
even death!
figure 12. Lubricating nailer via air inlet.
-14-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
h8234 parts breaKdoWn
-,
-+
-)
-*
'*
--
.%
&+
&,
-.
-&
&
.&
'
+&
-(
-'
'+
))
)*
)+
),
)-
).
*%
(
'-
',
'.
)
*
(%
('
)&
)%
.
&-
&.
'%
(.
(&
((
+
-
,
)'
)(
()
(*
-%
,.
&%
&&
'&
''
,+
,(
(+
(-
(,
,,
,-
*&
+*
,%
*'
*(
,*
,&
,'
++
,)
+'
&'
&(
+)
*)
+,
'(
')
+&
+)
*+
*,
+-
+%
+.
**
*-
&)
&*
*.
+(
*-
.'
.*
.(
.+
.,
.)
.-
..
-15-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
h8234 parts list
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PSB31M
CAP SCREW M8-1.25 X 25
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
PH8234051 SAFETY NOSE
2
PH8234002 EXHAUST PORT
PH8234003 SPACER
PH8234052 COPPER COLLAR
PH8234053 SAFETY NOSE CASE
3
4
PH8234004 CIRCULAR SPRING
PH8234005 RETAINING RING
PORS060
O-RING 59.5 X 2.0 S60
5
PH8234055 DRIVE GUIDE
6
PSB06M
PLW03M
CAP SCREW M6-1 X 25
LOCK WASHER 6MM
PLW04M
PSB13M
PSB26M
LOCK WASHER 8MM
7
CAP SCREW M8-1.25 X 30
CAP SCREW M6-1 X 12
8
PH8234008 CYLINDER PLUG
PSS07M SET SCREW M5-.8 X 5
9
PH8234059 MAGAZINE
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
PH8234010 CYLINDER COVER
PH8234011 PISTON STOP
PW03M
PN01M
FLAT WASHER 6MM
HEX NUT M6-1
PH8234012 SPRING SEAT
PH8234062 PUSHER
PH8234013 COMPRESSION SPRING
PH8234014 SPECIAL WASHER
PH8234015 PISTON COLLAR
PSB18M
PN04M
CAP SCREW M4-.7 X 8
HEX NUT M4-.7
PSB46M
CAP SCREW M4-.7 X 40
POR0079
O-RING 42.3 X 5
PH8234066 SAFETY SHAFT
PH8234067 SAFETY SHAFT CASING
PH8234068 PIN CASING
PH8234069 PIN
PH8234017 PISTON
PORG055
POR0080
O-RING 54.4 X 3.1 G55
O-RING 88 X 3
PH8234020 THREADED RETAINING RING
PH8234021 SEALING RING
PH8234022 CYLINDER
PH8234070 PUSHER CATCH
PRP42M
PRP03M
PSB93M
PN07M
ROLL PIN 3 X 20
ROLL PIN 5 X 20
CAP SCREW M3-.5 X 14
HEX NUT M3-.5
PH8234023 BUMPER
PH8234024 GASKET
PH8234025 NAILER BODY
PH8234026 SPACER
PH8234075 PIN B4 X 30
PH8234076 TORSION SPRING
PH8234077 SPRING CORE
PH8234078 PIN B5 X 12
PH8234027 PISTON VALVE SEAT
PORP015
PORS018
O-RING 14.8 X 2.4 P15
O-RING 17.5 X 1.5 S18
PH8234079 RELEASE LATCH
PH8234080 LATCH SPRING
PH8234030 PISTON VALVE
PORP006
PORP007
PORP009
O-RING 5.8 X 1.9 P6
O-RING 6.8 X 1.9 P7
O-RING 8.8 X 1.9 P9
PSB38M
PW02M
CAP SCREW M5-.8 X 25
FLAT WASHER 5MM
PH8234083 LATCH BRACKET
PN06M HEX NUT M5-.8
PH8234034 COMPRESSION SPRING
PH8234035 TRIGGER SHAFT
PH8234085 RUBBER GRIP
PH8234086 GASKET
PORS003
PORP020
O-RING 2.5 X 1.5 S3
O-RING 19.8 X 2.4 P20
PH8234087 END CAP
PH8234038 TRIGGER SEAT
PH8234039 TRIGGER PIN
PH8234040 TRIGGER
PSB15M
PLW01M
CAP SCREW M5-.8 X 20
LOCK WASHER 5MM
PH8234090 AIR QUICK CONNECT
PH8234091 AIR QUICK CONNECT CAP
PH8234092 PISTON REPAIR KIT
PH8234093 O-RING REPAIR KIT
PH8234094 CARRYING CASE
PH8234041 RUBBER RETAINING RING
PH8234042 SAFETY CATCH
PRP02M
PH8234044 SLIDING BRACKET
PRP16M ROLL PIN 3 X 25
PH8234046 COMPRESSION SPRING
ROLL PIN 3 X 16
PH8234095 SAFETY GOGGLES
PAW03M
PAW04M
PAW05M
PAW06M
HEX WRENCH 3MM
HEX WRENCH 4MM
HEX WRENCH 5MM
HEX WRENCH 6MM
PSB03M
PW02M
CAP SCREW M5-.8 X 8
FLAT WASHER 5MM
PH8234049 ADJUSTING NUT
PH8234050 SAFETY YOKE
-16-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
troubleshooting
symptom
Air leaking at trig-
possible cause
1. O-rings in trigger valve hous-
solution
1. O-rings must be replaced
& operation of safety nose
must be checked.
ing are damaged.
ger valve area.
Air leaking.
1. Loose screws in housing.
2. Damaged O-ring(s).
3. Loose air fitting.
1. Tighten screws.
2. Replace O-ring(s).
3. Tighten air fitting & use tef-
lon tape.
4. Damaged housing gasket(s).
4. Replace gasket(s).
Tool skips nails
while discharging.
1. excessive air pressure.
2. Air leaks.
3. Dirt in nose.
1. Reduce air pressure to tool.
2. Tighten screws and fittings.
3. Clean nose.
4. Dirt or damage prevents nails
from moving freely in maga-
zine.
4. Clean magazine and
inspect/repair damage.
5. Inadequate air flow to tool.
5. Check fitting, hose, com-
pressor & air pressure.
6. Replace piston O-ring.
Lubricate.
6. Worn O-ring on piston or lack
of lubrication.
7. Damaged O-rings on trigger
valve.
7. Replace trigger valve O-
rings.
8. Worn bumper.
9. Cap seal leaking.
8. Replace bumper.
9. Replace cap seal.
Tool runs slowly
or has a loss of
power.
1. Undersized air hose.
2. Nailer is not lubricated.
3. Broken spring in cap assem-
bly.
1. Use a larger air hose.
2. Lubricate nailer.
3. Replace spring.
4. exhaust port in cap is blocked. 4. Clean or replace damaged
internal parts.
5. Air pressure too low.
5. Increase air pressure.
Fasteners frequent- 1. Nails are the wrong size.
1. Use correct nails.
2. Use undamaged, clean
nails.
ly jam the nailer.
2. Nails are bent or dirty.
3. Magazine or nose screws are
loose.
3. Tighten magazine.
4. Replace worn or damaged
parts.
5. Use correct angle nails.
4. Driver or driver guide are worn
or damaged.
5. Nails are wrong angle.
Nailer does not fire. 1. Nailer is not lubricated.
1. Lubricate nailer.
2. Nail is jammed in magazine or 2. Clear nailer magazine or
discharge area.
discharge area.
3. Piston shaft is damaged.
4. Air pressure too low.
3. Replace piston shaft.
4. Check/increase air pres-
sure.
-17-
Model H8234 28° Framing Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and returns
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly or
indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte-
nance. This is Grizzly’s sole written warranty and any and all warranties that may be implied
by law, including any merchantability or fitness, for any particular purpose, are hereby limited
to the duration of this written warranty. We do not warrant or represent that the merchandise
complies with the provisions of any law or acts unless the manufacturer so warrants. In no
event shall Grizzly’s liability under this warranty exceed the purchase price paid for the prod-
uct and any legal actions brought against Grizzly shall be tried in the State of Washington,
County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they
constantly strive to achieve better quality equipment. We make every effort to ensure that
our products meet high quality and durability standards and we hope you never need to use
this warranty.
Please feel free to write or call us if you have any questions about the machine or the
manual.
grizzly industrial, inc.
1203 lycoming mall circle
muncy, pa 17756
phone: (570) 546-9663
fax: (800) 438-5901
e-mail:
techsupport@grizzly.com
Web site: http://www.grizzly.com
Thank you again for your business and continued support. We hope to serve you again
soon!
Download from Www.Somanuals.com. All Manuals Search And Download.
|