MODEL T10726
12" VISE-MOUNT
PAN & BOX BRAKE
OWNER'S MANUAL
(For models manufactured since 12/12)
Copyright © JANUAry, 2013 By grizzly iNdUstriAl, iNC.
WARNINg: NO PORTION Of ThIS MANUAL MAy BE REPRODUcED IN ANy ShAPE
OR fORM WIThOUT ThE WRITTEN APPROVAL Of gRIzzLy INDUSTRIAL, INc.
#ts15553 priNted iN ChiNA
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
INTRODUcTION............................................................................................................................... 2
Machine description................................................................................................................... 2
Contact info................................................................................................................................ 2
Manual Accuracy........................................................................................................................ 2
identification ............................................................................................................................... 3
specifications ............................................................................................................................. 3
SEcTION 1: SAfETy....................................................................................................................... 4
safety instructions for Machinery............................................................................................... 4
Additional safety for Brakes....................................................................................................... 6
SEcTION 2: SETUP......................................................................................................................... 7
Unpacking .................................................................................................................................. 7
Needed for setup....................................................................................................................... 7
inventory..................................................................................................................................... 7
Cleanup...................................................................................................................................... 8
site Considerations .................................................................................................................... 8
Workbench load .................................................................................................................................8
placement location.............................................................................................................................8
Workbench Mounting ................................................................................................................. 9
Assembly.................................................................................................................................... 9
SEcTION 3: OPERATIONS ........................................................................................................... 10
Basic Bending .......................................................................................................................... 10
removing/spacing Fingers ...................................................................................................... 11
SEcTION 4: AccESSORIES......................................................................................................... 12
SEcTION 5: MAINTENANcE......................................................................................................... 14
SEcTION 6: SERVIcE ................................................................................................................... 15
troubleshooting........................................................................................................................ 15
Finger Alignment ...................................................................................................................... 16
SEcTION 7: PARTS....................................................................................................................... 17
Main.......................................................................................................................................... 17
labels....................................................................................................................................... 18
WARRANTy & RETURNS ............................................................................................................. 21
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUcTION
Machine Description
Manual Accuracy
We are proud to provide a high-quality owner’s
manual with your new machine!
this 12" Vise-Mounted pan & Box Brake is
designed for small bending projects (such as
boxes, pans, and trays) in sheet metal that is 22
gauge or thinner.
We made every effort to be exact with the instruc-
tions, specifications, drawings, and photographs
contained inside. sometimes we make mistakes,
but our policy of continuous improvement also
means that sometimes the machine you receive
will be slightly different than what is shown in
the manual.
When secured in a sturdy bench-mounted vise,
four fingers of different lengths can be arranged
in a variety of combinations to make 90° bends
of varying widths up to 12" wide. the adjustable
fingers also permit the sides of a box to be bent
without interfering with previously bent sides.
if you find this to be the case, and the difference
between the manual and machine leaves you
confused about a procedure, check our website
for an updated version. We post current manuals
and manual updates for free on our website at
www.grizzly.com.
contact Info
We stand behind our machines. If you have
any questions or need help, use the information
below to contact us. Before contacting, please get
the serial number and manufacture date of your
machine. This will help us help you faster.
Alternatively, you can call our technical support
for help. Before calling, please write down the
Manufacture Date and Serial Number stamped
into the machine id label (see below). this infor-
mation helps us determine if updated documenta-
tion is available for your machine.
Grizzly Technical Support
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Email: [email protected]
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Manufacture date
serial Number
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: [email protected]
To reduce your risk of
serious injury, read this
entire manual BEfORE
using machine.
-2-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification
Finger
point
operating
lever
Finger Clamp
sleeve
eccentric
shaft
Finger
receiver
Finger
Cap screw
Finger
Clamp
Fingers
Vise lug
Specifications
Maximum Bending Width ............................... 12"
Maximum Bending Capacity ... 22 ga. Mild steel
Bending Angle range .............................. 0°–90°
Number of Fingers............................................. 4
Finger sizes............................... 1", 2", 3", and 6"
Weight .......................................................22 lbs.
-3-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 1: SAfETy
for your Own Safety, Read Instruction
Manual Before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
cOULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAy result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
OWNER’S MANUAL. read and understand this ELEcTRIcAL EQUIPMENT INJURy RISKS. you
owner’s manual BeFore using machine.
can be shocked, burned, or killed by touching live
electrical components or improperly grounded
machinery. to reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
TRAINED OPERATORS ONLy. Untrained oper-
ators have a higher risk of being hurt or killed.
only allow trained/supervised people to use this
machine. When machine is not being used, dis-
connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make workshop kid proof!
DIScONNEcT POWER fIRST. Always discon-
nect machine from power supply BeFore making
adjustments, changing tooling, or servicing machine.
this prevents an injury risk from unintended startup
or contact with live electrical components.
DANgEROUS ENVIRONMENTS. do not use
machinery in areas that are wet, cluttered, or have
poor lighting. operating machinery in these areas
greatly increases the risk of accidents and injury.
EyE PROTEcTION. Always wear ANsi-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. everyday
eyeglasses are not approved safety glasses.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin-
ery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.
-4-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
WEARINg PROPER APPAREL. do not wear fORcINg MAchINERy. do not force machine.
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to avoid
accidental slips, which could cause loss of work-
piece control.
it will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MAchINE. serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
hAzARDOUS DUST. dust created while using
machinery may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material,
and always wear a Niosh-approved respirator to
reduce your risk.
STABLE MAchINE. Unexpected movement dur-
ing operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE REcOMMENDED AccESSORIES. Consult
this owner’s manual or the manufacturer for rec-
ommended accessories. Using improper acces-
sories will increase the risk of serious injury.
hEARINg PROTEcTION. Always wear hear-
ing protection when operating or observing loud
machinery. extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
UNATTENDED OPERATION. to reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.
REMOVE ADJUSTINg TOOLS. tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
MAINTAIN WITh cARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
INTENDED USAgE. only use machine for its
intended purpose and never make modifications
not approved by grizzly. Modifying machine or
using it differently than intended may result in
malfunction or mechanical failure that can lead to
serious personal injury or death!
chEcK DAMAgED PARTS. regularly inspect
machine for any condition that may affect safe
operation. immediately repair or replace damaged
or mis-adjusted parts before operating machine.
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
MAINTAIN POWER cORDS. When disconnect-
ing cord-connected machines from power, grab
and pull the plug—Not the cord. pulling the cord
may damage the wires inside. do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
chILDREN & BySTANDERS. Keep children and
bystanders at a safe distance from the work area.
stop using machine if they become a distraction.
gUARDS & cOVERS. guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly.
EXPERIENcINg DIffIcULTIES. if at any time
you experience difficulties performing the intend-
ed operation, stop using the machine! Contact our
technical support at (570) 546-9663.
-5-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety for Brakes
cRUShINg & AMPUTATION INJURIES. the PINchINg. to prevent pinching injuries, lower the
brake can quickly crush or amputate fingers or fingers when not in use.
hands. Never place fingers or hands underneath
fingers.
gLOVES AND gLASSES. Always wear leather
gloves and approved safety glasses when using
SEcURINg Brake. Before using, secure brake to this brake.
a sturdy vise that is securely fastened to a work-
bench that can support the weight and dynamic hEATINg METAL. heating the workpiece with a
forces involved in bending sheet metal. otherwise, torch while it is in the brake will weaken the metal
the brake may unexpectedly move or fall, causing of the fingers and frame. do not use a torch or
serious injury or property damage.
other similar heating tool near the brake.
METAL EDgES. sharp edges on sheet metal can BAcK INJURIES. the operating lever motion
result in severe cuts. Always wear leather gloves required to operate this brake is potentially harm-
and chamfer/de-burr sharp sheet metal edges ful if proper technique is not used. to avoid back
before handling.
injuries, keep your back vertical and never over-
exert yourself.
TOOLS IN POOR cONDITION. Using this tool
with loose hardware or damaged components OVERLOADINg. overloading this machine can
could result in sudden, uncontrolled movements cause injury from flying parts if breakage occurs .
during use. inspect the brake for cracked compo- do not exceed the machine capacities.
nents, damaged linkage, levers, or loose fasten-
ers. Correct any problems before use.
Like all machinery there is potential danger
when operating this machine. Accidents
are frequently caused by lack of familiarity
or failure to pay attention. Use this machine
with respect and caution to decrease the
risk of operator injury. If normal safety pre-
cautions are overlooked or ignored, seri-
ous personal injury may occur.
No list of safety guidelines can be com-
plete. Every shop environment is different.
Always consider safety first, as it applies
to your individual working conditions. Use
this and other machinery with caution and
respect. failure to do so could result in
serious personal injury, damage to equip-
ment, or poor work results.
-6-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 2: SETUP
Unpacking
Inventory
Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover any damage, please call us immediately
at (570) 546-9663 for advice.
The following is a description of the main compo-
nents shipped with your machine. Lay the compo-
nents out to inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
Shipping Inventory: (figure 1)
Qty
When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.
A. Brake Assembly ......................................... 1
B. operating lever w/set screw M5-.8 x 8...... 1
c. lever shaft ................................................. 1
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine. Discard immediately.
A
B
Needed for Setup
C
the following are needed to complete the setup
process, but are not included with your machine.
figure 1. shipping inventory.
Description
Qty
•
•
•
•
•
•
•
Cleaner/degreaser (Page 8) ...... As Needed
disposable shop rags............... As Needed
sturdy Workbench...................................... 1
Vise secured to Workbench....................... 1
Wrench 17mm ............................................ 1
hex Wrench 2.5mm.................................... 1
hex Wrench 6mm....................................... 1
NOTICE
If you cannot find an item on this list, care-
fully check the machine and the packaging
materials. Some of these items may be pre-
installed for shipping or become misplaced
during unpacking.
-7-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
cleanup
Site considerations
the unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
this rust preventative works extremely well, but it
will take a little time clean.
Workbench Load
refer to Specifications on Page 3 for the
weight of your machine. some workbenches may
require additional reinforcement to support both
the machine and materials.
Always follow the manufacturer’s instructions with
any cleaning product you use and make sure you
work in a well-ventilated area to minimize expo-
sure to toxic fumes.
Placement Location
Consider existing and anticipated needs, size of
material to be processed through each machine,
and space for auxiliary stands, work tables or
other machinery when establishing a location for
your new machine. see figure 2 for the minimum
working clearances.
Before cleaning, gather the following:
•
•
•
•
•
•
disposable rags
Cleaner/degreaser (Wd•40 works well)
safety glasses & disposable gloves
plastic paint scraper (optional)
hex Wrench 6mm
Quality metal protectants products like g96®
gun treatment, slipit®, or Boeshield® t-9
(see Page 13 for offering from grizzly).
Vise
Basic steps for removing rust preventative:
1. put on safety glasses.
2. remove the fingers (refer to Page 11 for
detailed instructions).
331⁄4
3. Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it soak
for 5–10 minutes.
Brake
4. Wipe off the surfaces. if your cleaner/
degreaser is effective, the rust preventative
will wipe off easily. if you have a plastic paint
scraper, scrape off as much as you can first,
then wipe off the rest with the rag.
5. repeat Steps 3–4 as necessary until clean.
131⁄2
6. Apply a thin coat of quality metal protectant
to the fingers and other unpainted metal sur-
faces, then re-install the fingers.
figure 2. Minimum working clearances.
Avoid chlorine-based solvents, such as
acetone or brake parts cleaner, that may
damage painted surfaces.
-8-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Vise & Workbench
Setup
except for the operating lever, the Model t10726
has been assembled and adjusted at the factory.
the forces exerted on the brake during operation
are substantial. the brake must be firmly secured
in a vise (see figure 5) that is solidly attached
to a workbench that will support the weight and
dynamic pressures of the operation (refer to Page
12 for workbench and vise options from grizzly).
To attach the operating lever:
1. thread the operating lever shaft (see figure
3) into the eccentric shaft, and tighten it with
the wrench.
Mount the brake by tightening the vise jaws
against the lug at the bottom of the brake.
Note: Use pieces of cardboard, wood, or padded
jaw faces between the vise jaws and the vise lug
to prevent surface damage to the brake.
operating
lever shaft
eccentric
shaft
figure 3. operating lever shaft installed.
2. slide the operating lever onto the lever shaft
(see figure 4), and secure it with the pre-
installed set screw.
Vise
lug
figure 5. example of Model t10726 secured in
vise mounted to a workbench.
set screw
Make sure the workbench that the brake will
be mounted on is stable and can support
the weight of the tool, the workpiece, and
the forces exerted during operation.
operating
lever
figure 4. operating lever attached.
-9-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 3: OPERATIONS
Basic Bending
Damage to your eyes or hands could result
from using this brake without proper protec-
tive gear. Always wear safety glasses and
leather gloves when operating this brake.
the Model t10726 bends mild steel up to 22
gauge at angles up to 90°.
To perform a basic bending operation:
1. Clean away any debris from the workpiece.
2. Use a pencil or scribe to mark the bending
location.
3. lift the operating lever and center the
workpiece under the fingers and directly over
the mark you made in Step 2 (see figure 6).
If you are not experienced with this type
of machine, WE STRONgLy REcOMMEND
that you seek additional training outside of
this manual. Read books/magazines or get
formal training before beginning any proj-
ects. Regardless of the content in this sec-
tion, grizzly Industrial will not be held liable
for accidents caused by lack of training.
figure 6. Workpiece positioned under fingers.
Keep your fingers and
hands away from the fin-
gers during operation to
avoid the risk of crushing
injuries.
-10-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. slowly lower the operating lever until the
bend in the workpiece reaches the desired
angle (see figure 7 for an example).
2. From the rear of the brake, carefully push the
fingers forward, as shown in figure 8, then
slowly lower the lever behind the brake. the
fingers should clear the front of the frame as
they are lowered.
Note: Make sure the finger points are directly
over the finger receiver groove as you lower
the lever.
Finger Cap
screw
Fingers Forward
of Frame
figure 8. Fingers positioned forward of frame.
3. remove the cap screw(s) that secure the
finger, then pull the fingers from the clamps.
figure 7. example of a 90° bend.
Note: It may be necessary to loosen the first
cap screw on the finger(s) adjacent to the one
you are removing to release the clamping
pressure.
5. lift the operating lever to raise the fingers,
remove the bent workpiece, then lower the
fingers back into the finger receiver.
4. position the fingers in an arrangement for
the length or width of the desired bend (see
figure 9 for an example).
If a pan or box is desired, refer to the next
subsection to position the fingers for this
operation.
Note: As you move or replace fingers, make
sure they are aligned with each other (see
Finger Alignment on Page 16 for detailed
instructions).
Removing/Spacing
fingers
Finger Clamp
the fingers can be spaced for pan and box opera-
tions. this involves removing one or more fingers
so that the others can be properly spaced.
Tool Needed
Qty
hex Wrench 6mm.............................................. 1
figure 9. example of finger spacing.
To remove and space fingers:
5. raise the fingers up, then lower them back
into the finger receiver.
1. lift the operating lever to raise the fingers.
-11-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCessories
SEcTION 4: AccESSORIES
g5618—Deburring Tool with two Blades
the quickest tool for smoothing freshly sheared
metal edges. Comes with two blades, one for
steel and aluminum and one for brass and cast
iron.
Installing unapproved accessories may
cause machine to malfunction, resulting in
serious personal injury or machine damage.
To reduce this risk, only install accessories
recommended for this machine by grizzly.
NOTICE
Refer to our website or latest catalog for
additional recommended accessories.
figure 11. Model g5618 deburring tool.
heavy-Duty Bench Vises with Anvils
g7059—5", 45 lbs.
g7060—6", 68 lbs.
these tough vises are ideal for all bench work
applications. large machined center slide keeps
jaws aligned under maximum pressure. other
features include large Acme screws, anvil faces,
and 0°–90° swivel.
Super heavy-Duty Birch Workbench
h8361—60" x 30"
h8362—72" x 36"
sized to fit the needs of any shop, these super
heavy-duty Birch Workbenches have solid 3"
thick tops that stand 38" above the floor. the end
vise measures 143⁄4" wide (h8361) or 173⁄4" wide
(h8362) and has a 7" maximum capacity. stable
laminated birch provides strength and durability.
you'll be proud to have this workbench in your
shop!
figure 10. heavy-duty Bench Vise with Anvil.
figure 12. super heavy-duty Birch Workbench.
-12-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
Bostitch compound Action Aviations Snips
T22298—Straight
T22299—Left
Basic Eye Protection
T20501—face Shield crown Protector 4"
T20502—face Shield crown Protector 7"
T20503—face Shield Window
T20452—"Kirova" Anti-Reflective S. glasses
T20451—"Kirova" clear Safety glasses
h0736—Shop fox® Safety glasses
h7194—Bifocal Safety glasses 1.5
h7195—Bifocal Safety glasses 2.0
h7196—Bifocal Safety glasses 2.5
T22300—Right
these 10" Aviation snips are designed for cut-
ting heavy stock in a straight, left, or right cut-
ting direction. developed with tiN-coated cutting
blades to reduce wear and extend blade life, they
cut up to 18 gauge cold-rolled steel or 23 gauge
stainless steel. the patented flush-mounted side
hardware also helps prevent metal from catching
while cutting. these snips meet or exceed ANsi
standards.
T20502
T20452
t22298
T20503
T20451
h0736
t22299
h7194
figure 13. Assortment of basic eye protection.
t22300
Recommended Metal Protectants
g5562—SLIPIT® 1 Qt. gel
g5563—SLIPIT® 12 oz Spray
g2871—Boeshield® T-9 12 oz Spray
g2870—Boeshield® T-9 4 oz Spray
h3788—g96® gun Treatment 12 oz Spray
h3789—g96® gun Treatment 4.5 oz Spray
figure 15. Bostitch Compound Aviation snips.
figure 14. recommended products for protect-
ing unpainted cast iron/steel part on machinery.
-13-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 5: MAINTENANcE
regular maintenance on the Model t10726 will
ensure its optimum performance. Make a habit of
inspecting your brake each time you use it.
•
finger clamp Sleeve Lubrication. to
reduce wear, periodically apply a couple of
drops of light machine oil to each end of the
finger clamp sleeves (see figure 17), then
slide the sleeves side-to-side several times to
distribute the oil. Wipe away any excess oil.
There are three main areas to maintain on the
Model T10726:
•
fingers and finger Receiver. After han-
dling the fingers for removal, spacing, or
re-installation, always apply a quality metal
protectant to the fingers and finger receiver
(see Page 13 for offerings from grizzly) to
prevent corrosion.
Apply oil here
When storing the brake for long periods of
time, make a habit of occasionally re-apply-
ing the metal protectant as directed above.
•
Eccentric Shaft Rod. periodically or if the
up-and-down finger movement becomes stiff,
apply a couple of drops of light machine oil to
the eccentric shaft rods on each end of the
eccentric shaft (see figure 16). the rods are
accessible between the eccentric shaft and
the roller brackets. rotate the lever front-to-
back several times to distribute the oil, then
wipe away any excess.
figure 17. Finger clamp lubrication points.
eccentric
shaft rod
eccentric
shaft
roller
Bracket
figure 16. eccentric shaft rod between the
eccentric shaft and the frame.
-14-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 6: SERVIcE
Review the troubleshooting and procedures in this section if a problem develops with your machine. If you
need replacement parts or additional help with a procedure, call our Technical Support at (570) 546-9663.
Note: Please gather the serial number and manufacture date of your machine before calling.
Troubleshooting
Symptom
Possible cause
Possible Solution
heavy resistance
during bends.
1. Machine capacities are exceeded.
1. Use sheet metal that does not exceed 22 gauge
mild steel.
2. Fingers not aligned with finger receiver
groove.
2. Make sure fingers are aligned with finger receiver
groove as fingers are lowered for bend.
Bend radius is not
consistent across
workpiece.
1. Machine capacities are exceeded.
1. Use sheet metal that does not exceed 22 gauge
mild steel.
2. Bottom of fingers not aligned with each
other.
2. Make sure fingers are firmly seated in finger clamps
and the finger points are aligned with each other.
point of fingers are
chipping or rolling.
1. Fingers not aligned with finger receiver
groove.
1. Make sure fingers are aligned with finger receiver
groove as fingers are lowered for bend. replace
fingers if damaged.
2. Machine capacities are exceeded.
2. Use sheet metal that does not exceed 22 gauge
mild steel. replace fingers if damaged.
Workpiece shows
scoring marks or
scratches after
bend.
1. debris on fingers or finger receiver.
1. Clean fingers and finger receiver (Page 14).
2. polish out scratches, and apply tape on the
workpiece at the bend locations for protection.
2. Fingers or finger receiver has scratches.
-15-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
look along the length of the fingers from the side
to identify any finger point that is not aligned with
the rest.
finger Alignment
to produce straight bends, the finger points (see
figure 18) must all be aligned evenly.
Tool Needed
hex Wrench 6mm.............................................. 1
Qty
When moving or re-installing the fingers, there is
play in the vertical positioning which can be used
to align the fingers.
To align the finger points:
1. loosen, but do not remove, the cap screws
that secures the finger.
Finger
Cap screws
Note: It may be necessary to also loosen
the cap screws on each side of the finger to
relieve the pressure from the finger clamp.
2. Apply upward pressure to the finger to firmly
seat it into the finger clamp.
3. observe the alignment of the finger points
from the side again. if necessary, repeat this
procedure to bring all fingers into alignment.
Finger
Clamp
Finger points
figure 18. Finger points and cap screws.
-16-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
SEcTION 7: PARTS
Main
20
19
12
9
21
22
11
13
14
10
15
16
17
5
2
1
3
8
4
7
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PT10726001
VISE LUG
FRAME
12
13
14
15
16
17
19
20
21
22
PT10726012
SLEEVE STOP PLATE
STOP PLATE RIVET
BENDING LEVER SHAFT
FINGER CLAMP
2
PT10726002
PT10726003
PT10726004
PT10726005
PT10726007
PT10726008
PT10726009
PT10726010
PT10726011
PT10726013
PT10726014
PT10726015
PCAP31M
PLW04M
3
BENDING FINGER 75MM
BENDING FINGER 50MM
STOP ROD 6 X 30MM
4
5
CAP SCREW M8-1.25 X 25
LOCK WASHER 8MM
BENDING LEVER
7
BENDING FINGER 25MM
BENDING FINGER 150MM
ECCENTRIC SHAFT
8
PT10726019
PT10726020
PSS31M
9
LEVER HANDLE
10
11
ECCENTRIC SHAFT ROD
FINGER CLAMP SLEEVE
SET SCREW M5-.8 X 8
SET SCREW M5-.8 X 12
PSS53M
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.
-17-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
Labels
31
32
33
34
35
REF PART #
REF PART #
DESCRIPTION
DESCRIPTION
31
32
33
PT10726031
ID LABEL
34
35
PT10726034
PPAINT-01
EYE INJURY HAZARD LABEL
PT10726032
PT10726033
HAZARD STRIP LABEL
PINCH HAZARD LABEL
GRIZZLY GREEN TOUCH-UP PAINT
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes
off or becomes unreadable, the owner of this machine MUST replace it in the original location
-18-
Model T10726 (Mfg. Since 12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_____________________________________________________________________________
Street_____________________________________________________________________________
City _______________________ State_________________________ Zip _____________________
Phone #____________________ Email _________________________________________________
Model # ____________________ Order #_______________________ Serial #__________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop
better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
____ Advertisement
____ Card Deck
____ Friend
____ Website
____ Catalog
____ Other:
2. Which of the following magazines do you subscribe to?
____ Cabinetmaker & FDM
____ Family Handyman
____ Hand Loader
____ Popular Science
____ Popular Woodworking
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Rifle
____ Shop Notes
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Woodwork
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Model Airplane News
____ Old House Journal
____ Popular Mechanics
____ Shotgun News
____ Today’s Homeowner
____ Wood
3. What is your annual household income?
____ $20,000-$29,000
____ $30,000-$39,000
____ $40,000-$49,000
____ $70,000+
____ $50,000-$59,000
____ $60,000-$69,000
4. What is your age group?
____ 20-29
____ 30-39
____ 60-69
____ 40-49
____ 70+
____ 50-59
5. How long have you been a woodworker/metalworker?
____ 0-2 Years ____ 2-8 Years
____ 8-20 Years
____20+ Years
____10+
6. How many of your machines or tools are Grizzly?
____ 0-2 ____ 3-5
____ 6-9
7. Do you think your machine represents a good value?
8. Would you recommend Grizzly Industrial to a friend?
_____Yes
_____Yes
_____No
_____No
9. Would you allow us to use your name as a reference for Grizzly customers in your area?
Note: We never use names more than 3 times. _____Yes _____No
10. Comments:_____________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
_________________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTy & RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then issue
you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We
will not accept any item back without this number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Download from Www.Somanuals.com. All Manuals Search And Download.
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
~Since 1983~
Visit Our Website Today For
Current Specials!
ORDER
24 HOURS A DAY!
1-800-523-4777
Download from Www.Somanuals.com. All Manuals Search And Download.
|