18 GAUGE FINISH ANGLE NAILER
MODEL H5570
INSTRUCTION MANUAL
COPYRIGHT © SEPT, 2003 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN TAIWAN
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE
AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CONFIGURATION CAN CHANGE AS
PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF
THE MACHINE, THIS MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE . CONTACT CUS-
TOMER SERVICE IF YOU HAVE ANY QUESTIONS ABOUT DIFFERENCES.
PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions For Pneumatic Tools
18. DISCONNECT TOOLS before ser-
10. USE PROPER AIR HOSE for the
tool. Make sure your air hose is in
good condition and is long enough to
reach your work without stretching.
vicing and changing accessories.
19. USE
THE
RECOMMENDED
Consult the
ACCESSORIES.
owner’s manual for recommended
accessories. The use of improper
accessories may cause risk of
injury.
11. WEAR PROPER APPAREL. DO
NOT wear loose clothing, gloves,
neckties, rings, bracelets, or other
jewelry which may get caught in
moving parts. Non-slip footwear is
recommended. Wear a protective
hair covering to contain long hair.
20. CHECK
DAMAGED
PARTS.
Before further use of the tool, a
guard or other part that is damaged
should be carefully checked to
determine that it will operate prop-
erly and perform its intended func-
tion. Check for alignment of moving
parts, binding of moving parts,
breakage of parts, mounting, and
any other conditions that may affect
its operation. A guard or other part
that is damaged should be properly
repaired or replaced.
12. ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask if cut-
ting operation is dusty. Everyday
eyeglasses only have impact resis-
tant lenses, they are NOT safety
glasses.
13. WEAR APPROVED HEARING
PROTECTION.
14. SECURE WORK. Use clamps or a
vise to hold work when practical. It is
safer than using your hand and frees
both hands to operate tool.
21. NEVER LEAVE UNATTENDED
TOOL CONNECTED TO AIR.
Disconnect the air hose and DO
NOT leave tool until it is relieved of
any built up pressure.
15. DO NOT OVERREACH. Keep prop-
er footing and balance at all times.
16. MAINTAIN TOOLS WITH CARE.
Keep tools lubricated and clean for
best and safest performance. Follow
instructions for lubricating and
changing accessories.
22. NEVER ALLOW UNTRAINED
USERS TO USE THIS TOOL
WHILE UNSUPERVISED.
23. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING THE TOOL. Seek formal
training or research books or maga-
zines that specialize in pneumatic
tools.
17. REDUCE THE RISK OF UNINTEN-
TIONAL STARTING. DO NOT carry
tool with hand on trigger and always
disconnect from air when not in use.
-2-
H5570 18 Gauge Finish Angle Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Nailer Safety
In addition to the rules stated in the previ-
ous section, and those in the warning
boxes throughout this manual, please
observe the following safety tips for your
new nailer:
1. READ THIS ENTIRE MANUAL
BEFORE OPERATING THE NAIL-
ER.
2. ALWAYS DISCONNECT AIR FROM
THE NAILER WHENEVER SERVIC-
ING OR INSTALLING NAILS. During
maintenance, a nailer connected to
air may fire accidentally, causing seri-
ous personal injury.
3. DO NOT PLACE HANDS NEAR
NAIL POINT OF ENTRY. Nail can
deflect and tear through the surface
of the workpiece, puncturing your
hand or fingers.
Operating this nailer can propel
objects into the air, causing immedi-
ate eye damage. To protect yourself,
always wear American National
Standards Institute (ANSI) approved
safety glasses or goggles when oper-
ating this equipment. In addition, this
nailer discharges at 85-90 decibels.
To protect your hearing, always wear
ANSI approved ear protection when
operating this nailer.
4. NEVER CONNECT THE NAILER TO
PRESSURIZED
OXYGEN
OR
OTHER COMBUSTIBLE GASES AS
A POWER SOURCE. Only use fil-
tered, lubricated, and regulated com-
pressed air.
5. NEVER USE GASOLINE OR
OTHER FLAMMABLE LIQUIDS TO
CLEAN THE NAILER. Vapors in the
tool will ignite by a spark and cause
the tool to explode.
6. DO NOT CARRY THE NAILER BY
ANY OTHER PART THAN THE
HANDLE, and do not carry the nailer
by the air hose.
7. DO NOT KEEP THE TRIGGER
PULLED ON THE SAFETY YOKE
MECHANISM WHEN CARRYING
OR HOLDING THE TOOL.
8. DO NOT USE A CHECK VALVE OR
ANY OTHER FITTING THAT
ALLOWS AIR TO REMAIN IN THE
TOOL.
Never point this nailer at yourself or
another person! Always pay attention
to the direction this nailer is pointed.
Use this tool with respect and caution
to lessen the possibility of operator or
bystander injury. Ignoring this warn-
ing may result in serious personal
injury.
-3-
H5570 18 Gauge Finish Angle Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Most importantly, we stand behind our
Commentary
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
We are proud to offer the Grizzly Model
H5570 18 Gauge Finish Angle Nailer. This
model is part of a growing Grizzly family of
fine power tools. When used according to
the guidelines set forth in this manual, you
can expect years of trouble-free, enjoyable
operation and proof of Grizzly’s commit-
ment to customer satisfaction.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
We are pleased to provide this manual with
the Model H5570. It was written to encour-
age safety considerations and guide you
through general operating procedures and
maintenance. This manual represents our
effort to produce the best documentation
possible.
The specifications, details, and pho-
tographs in this manual represent the
Model H5570 as supplied when the manu-
al was prepared. However, owing to
Grizzly’s policy of continuous improve-
ment, changes may be made at any time
with no obligation on the part of Grizzly. If
you have any comments regarding this
manual, please write to us at the address
below:
Read the manual before assembly
and operation. Become familiar with
this tool, its safety instructions, and
its operation before beginning any
work. Serious personal injury may
result if safety or operational infor-
mation is not understood or followed.
Grizzly Industrial, Inc.
C
/O
Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
-4-
H5570 18 Gauge Finish Angle Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
Compressed Air System
Safety Yoke Mechanism
The Model H5570 is designed to be oper-
ated at 70-100 psi. DO NOT exceed the
maximum operating pressure for your
model.
A safety yoke mechanism (bump fire) on
the nose of the nailer acts as a secondary
safety device. When the trigger is pressed,
the nailer will not fire until the safety yoke
mechanism is depressed.
Before using your new nailer, install the
included 1⁄4" NPT male quick connect fitting
on the nailer and a ⁄4" NPT female fitting
on the air hose. Regulate the air pressure
on your air compressor to barely over the
minimum psi for your model.
Before you use your nailer for the first time,
check the safety yoke mechanism to
ensure proper function. To do this:
1
1. Make sure the nailer is disconnect-
ed from the air supply!
Many pneumatic tools benefit from an in-
line filter/lubricator/regulator unit. Using
this unit protects your tool from damaging
water build-up, allows you to adjust and
maintain constant air pressure to your tool,
and saves you the inconvenience of having
to manually lubricate your tool every time
you use it. Check the current Grizzly cata-
log for availability of this unit. If you plan on
installing a filter/lubricator/regulator unit in
your compressed air system, always follow
the connection instructions that come with
the unit.
2. Make sure the magazine is empty and
contains no nails.
3. Make sure the trigger and the safety
yoke mechanism move up and down
without sticking.
4. Connect the nailer to the air supply.
5. Without pressing the trigger,
depress the safety yoke mechanism
against a scrap piece of wood that is
clean and free of any knots, nails, or
other foreign objects. If the nailer
does not fire, then the safety yoke
mechanism is working correctly. If the
nailer does fire when you do this,
immediately disconnect the nailer
from the air supply and call our cus-
tomer service for help.
Similarly if the nailer fires when the trigger
is pulled, without the safety yoke mecha-
nism being depressed, then the nailer is
not working properly.
If either of these two conditions develop
after you have used your nailer for a peri-
od of time, check the lubrication of these
mechanisms.
Exceeding the maximum permissible
operating pressure may cause the
nailer to explode, blowing metal frag-
ments in all directions. To protect
yourself from serious personal injury,
DO NOT allow your air compressor to
exceed the recommended pressure
when connected to this nailer!
The safety yoke is
a
mechanical
device that can fail. Never rely on the
safety yoke mechanism as an excuse
to point the nailer at yourself or any
bystanders. Serious injury may occur.
-5-
H5570 18 Gauge Finish Angle Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Oiling Nailer
Loading Nailer
When replacing nails in your Model
H5570, follow these guidelines:
Special oil has been included with your
new Grizzly nailer to help maintain its use-
ful life. Place one drop of oil in the nailer air
inlet (as shown in Figure 1) before every
use. Wipe off any excess oil near the nail-
er exhaust to avoid dust build-up. When
the oil that was included with the nailer has
been completely used, replace with Grizzly
Model G2820 Pneumatic Tool Oil.
Gauge: 18
3
Length:
⁄4"-2"
Capacity: 100
To load your nailer:
1. Disconnect the air supply from the
nailer!
Another option to manual oiling would be
to install a lubricator in your air compressor
line. If your air compressor line already has
a lubricator, then regular lubrication of your
nailer will not be necessary. Just make
sure there is always oil in the lubricator.
2. Slide back the magazine pusher until
it stops as shown in Figure 2.
As mentioned before, the best option is to
install a filter/lubricator/regulator unit such
as the Grizzly Model H4196 in your air line.
Figure 2. Releasing magazine pusher.
3. Load a nail stick in the T-slot at the top
of the magazine as shown in Figure 3.
4. Release the magazine pusher by
pulling it back, depressing the release
button, and sliding it forward.
Figure 1. Lubricating nailer via air inlet.
Figure 3. Loading finish nails into nailer.
-6-
H5570 18 Gauge Finish Angle Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Before pressing the trigger, make
sure your free hand is positioned out
of the way of a potential path of a nail
in case of deflection. (Deflection is
caused when grain irregularities,
knots or foreign objects inside the
wood cause the nail to change its
path, resulting in the nail puncturing
the surface of the workpiece as
shown in Figure 4.) Besides damag-
ing your workpiece, deflection can
cause injury if your free hand is secur-
ing the workpiece in the location that
the nail deflects.
4. Press the trigger. If the finish nail
drove into the wood far enough, con-
tinue with your intended operations. If
the nail either went too far or not far
enough, then adjust the depth adjust-
ment knob.
Operating Nailer
If you have not read the safety instruc-
tions in this manual, DO NOT operate
the nailer.
Before you operate your nailer, place one
drop of the included oil into the quick con-
nect fitting where the nailer connects to the
air supply.
To operate your nailer:
1. Connect the air supply to the quick
connect fitting.
2. Test the loaded nailer for proper nail
penetration. Hold the nailer perpen-
dicular to the surface of a piece of
clean scrap wood that is thick enough
for the length of finish nails you have
loaded. Depress the safety yoke
mechanism on your workpiece.
5. Turn the knob clockwise to drive the
nail deeper, or counterclockwise if the
nail is going too deep. (Figure 5.)
Figure 4. Example of nail deflection.
Figure 5. Depth adjustment knob.
-7-
H5570 18 Gauge Finish Angle Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
Clearing Jammed Nails
To clear a jammed nail from the dis-
charge area on the Model H5570:
1. Disconnect the nailer from the air
supply!
2. Pull the spring loaded pusher all the
way back and remove the nail stick.
3. Flip up the quick release latch located
on top of the nailer nose assembly as
shown in Figure 6.
4. Remove the driver guide cover as
shown in Figure 7.
5. The jammed nail should now be visi-
ble; remove it from the discharge area
with needle nose pliers.
Always disconnect air from nailer
whenever clearing a jammed nail!
Cleaning Nailer
Use a good solvent to clean the nose
assembly of the nailer. Always be sure that
the nailer is dry before using it again.
6. Replace the driver guide cover and
snap the quick release latch back into
operating position.
Do not allow dust, chips, sand, etc. into the
air connectors or into the body of the nail-
er; this may result in leaks and damage to
the nailer and the air couplings.
Figure 6. Releasing guide cover latch.
Never use gasoline or other flamma-
ble liquids to clean this tool. Vapors
in the tool may ignite, causing the
tool to explode. Ignoring this warning
may lead to serious personal injury or
even death!
Figure 7. Removing driver guide cover.
-8-
H5570 18 Gauge Finish Angle Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
5. The top of the piston should now be
visible inside the cylinder, which is
housed in the head of the nailer.
6. Open the magazine.
7. Watch the discharge area and push
the top of the piston with your finger.
You will see the piston shaft slide
down the discharge area.
Replacing Pistons/O-Rings
If you use your nailer day in and day out,
Grizzly offers repair pistons as cheap
insurance against wasted down time and
lost profits in the event that a piston or pis-
ton shaft becomes worn out.
8. With a long flathead screwdriver or
similarly shaped tool, push the piston
shaft back inside the nailer until you
can grip the piston head and remove
it from the cylinder. (Be careful not to
scratch the discharge area when
pushing the piston shaft with the
screwdriver.)
9. Place a new O-ring on the new piston
and apply a thin film of the nailer lubri-
cating oil on the O-ring.
10. Insert the new piston in the cylinder.
Make sure that the grooves on the
piston shaft line up with those on the
guide at the bottom of the cylinder.
The new piston should easily slide
into the cylinder. DO NOT force the
piston into the cylinder! If the piston
is not easily inserted, double-check
the alignment of the piston shaft with
the grooves on the guide.
11. After the piston is inserted correctly,
close the magazine. Replace the rear
cap assembly and tighten the 4 cap
screws.
12. For more assistance, or to install a
complete O-ring set, refer to the
appropriate breakdown diagram in the
back of this manual.
Always disconnect air from nailer
whenever servicing! During mainte-
nance, a nailer connected to air may
fire accidentally, causing serious
personal injury!
To replace a piston:
1. Disconnect the nailer from the air
supply!
2. Remove all nails from the magazine
cartridge.
3. Remove the 4 cap screws on the back
of the nailer, near the exhaust port.
4. Remove the rear cap as shown in
Figure 8.
Figure 8. Removing rear cap.
-9-
H5570 18 Gauge Finish Angle Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
H5570 PART BREAKDOWN
-10-
H5570 18 Gauge Finish Angle Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
REF PART #
01 PSB113M
DESCRIPTION
REF PART #
40 PSB33M
DESCRIPTION
BTN CAP SCR M5-.8 X 11
CAP SCREW M5-.8 X 12
02 PH5570002 EXHAUST COVER
03 PH5570003 SEAL
41 PH5570041 DRIVER GUIDE
43 PSB97M
43-1 PLW01M
CAP SCREW M5-.8 X 6
LOCK WASHER 5MM
04 PSB15M
05 PSS08M
CAP SCREW M5-.8 X20
SET SCREW M4-.7 X 5
44 PH5570044 PIN
06 PH5570006 CAP
45 PH5570045 MAGAZINE
46 PH5570046 NAIL GUIDE LINER
47 PH5570047 UPPER COVER
48 PH5570048 SPIRAL SPRING
49 PH5570049 COVER
07 PH5570007 PISTON STOPPER
08 PH5570008 O RING
09 PH5570009 COLLAR
10 PH5570010 O RING
11 PH5570011 SPRING
12 PH5570012 PISTON HEAD VALVE
13 PH5570013 STOPPER
14 PH5570014 O RING
15 PH5570015 O RING
16A PH5570016A DRIVER ASSEMBLY
17 PH5570017 CYLINDER
18 PH5570018 O RING
19 PH5570019 BUMPER
20 PH5570020 GASKET
21 PH5570021 O RING
22 PH5570022 BODY
49-1 PH5570049-1 ROLLER
50 PH5570050 PUSHER
51 PH5570051 FOLLOWER SEAT
52 PH5570052 SPECIAL SCR M4-.7 X 6
53 PH5570053 SPRING
54 PH5570054 FOLLOWER BODY
55 PH5570055 SPECIAL SCR M4-.7 X 6
56 PS09M
PHLP HD SCR M5-.8 X 10
57 PH5570057 SET PLATE
58 PH5570058 BRACKET
58-1 PSB18M
59 PLN01M
CAP SCREW M4-.7 X 8
LOCK NUT M4-.7
23 PSB24M
CAP SCREW M5-.8 X 16
60 PH5570060 TAIL COVER
61 PHTEK26M TAP SCREW M5-.8 X 10
62 PH5570062 POSITIONING PLATE
63 PH5570063 DEPTH ADJUST KNOB
63-1 PH5570063-1 SPRING
24 PH5570024 1/4" NPT MALE CONNECT
25 PH5570025 DRIVER GUIDE WASHER
26 PH5570026 PIN
27 PH5570027 SPRING
28 PH5570028 GUIDE SAFETY LEVER
29A PH5570029A SAFETY LEVER
64 PH5570064 GUIDE PLATE
65 PH5570065 PIN
36 PRP42M
ROLLED PIN M3 X 20
66 PH5570066 SET SHAFT
37A PH5570037A LATCH
*67 PH5570067 CARRYING CASE
38 PH5570038 DRIVER GUIDE COVER
39 PH5570039 PIN
*68 PAW3M
*69 PAW4M
ALLEN WRENCH 3MM
ALLEN WRENCH 4MM
39-1 PEC01M
E RING 3MM
* These items are not shown in the illustration.
-11-
H5570 18 Gauge Finish Angle Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
CAUSE
PROBLEM
ACTION
Air leaking at trigger valve
area.
1. O-rings in trigger valve
housing are damaged.
1. O-rings must be replaced
& operation of safety
yoke must be checked.
Air leaking between hous-
ing and hose.
1. Loose screws in housing.
2. Damaged O-ring.
3. Loose air fitting.
1. Tighten screws.
2. Replace O-ring.
3. Tighten air fitting.
Air leaking between hous-
ing and cap assembly.
1. Damaged seal.
1. Air leaks.
1. Replace damaged seals.
Tool skips nails while dis-
charging.
1. Tighten screws and fit-
tings.
2. Dirt in nose.
2. Clean nose.
3. Dirt or damage prevents nails
from moving freely in maga-
zine.
3. Clean magazine and
inspect/repair damage.
4. Inadequate air flow to tool.
4. Check fitting, hose, com-
pressor & air pressure.
5. Replace piston O-ring.
Lubricate.
5. Worn O-ring on piston or lack
of lubrication.
6. Damaged O-rings on trigger
valve.
6. Replace trigger valve O-
rings.
7. Worn bumper.
8. Cap seal leaking.
7. Replace bumper.
8. Replace cap seal.
Tool runs slowly or has a
loss of power.
1. Nailer is not sufficiently lubri-
cated.
2. Broken spring in cap assem-
1. Lubricate nailer.
2. Replace spring.
bly.
3. Exhaust port in cap is
blocked.
3. Clean or replace dam-
aged internal parts.
Fasteners frequently jam
the nailer.
1. Nails are the wrong size.
2. Nails are bent.
3. Magazine or nose screws are
loose.
1. Use correct nails.
2. Use undamaged nails.
3. Tighten magazine and
nose screws.
4. Driver or driver guide are
worn or damaged.
4. Replace worn or dam-
aged parts.
5. Nails are wrong angle.
5. Use correct angle nails.
Nailer does not fire.
1. Nail is jammed in maga-
zine or discharge area.
2. Piston shaft is damaged.
3. Air pressure too low.
1. Clear nailer magazine or
discharge area.
2. Replace piston shaft.
3. Check/increase air pres-
sure.
-12-
H5570 18 Gauge Finish Angle Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main-
tenance. This is Grizzly’s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are here-
by limited to the duration of this written warranty. We do not warrant or represent that the
merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, con-
tingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Number,” which must be clearly posted on the outside as
well as the inside of the carton. We will not accept any item back without this number. Proof
of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they con-
stantly strive to achieve better quality equipment. We make every effort to ensure that our
products meet high quality and durability standards and we hope you never need to use this
warranty.
Please feel free to write or call us if you have any questions about the machine or the man-
ual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon!
-13-
H5570 18 Gauge Finish Angle Nailer
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name__________________________________________________________
Street__________________________________________________________
City____________________State________Zip_________
Phone Number____________E-Mail___________________FAX____________
Model #_______________Serial#________________Order #______________
The following information is given on a voluntary basis. It will be used for marketing purposes to help
us develop better products and services. Of course, all information is strictly confidential.
9. How many of the machines checked above are
Grizzly? ____________
1. How did you learn about us?
___Advertisement
___Friend
___Catalog
___World Wide Web
___Other__________________________
___Card Deck
10. Which portable/hand held power tools do you own?
Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
2. What is your annual household income?
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
___Miter Saw
___Other_________________________________
3. What is your age group?
___20-29
11. What machines/supplies would you like Grizzly
Industrial to carry?
___50-59
___60-69
___70 +
___30-39
___40-49
________________________________________
________________________________________
________________________________________
________________________________________
4. How long have you been a woodworker?
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
12. What new accessories would you like Grizzly
Industrial to carry?
5. How would you rank your woodworking skills?
________________________________________
________________________________________
________________________________________
________________________________________
___Simple
___Advanced
___Intermediate
___Master Craftsman
6. What stationary woodworking tools do you own?
Check all that apply.
13. What other companies do you purchase your tools
and supplies from?
___Air Compressor
___Band Saw
___Panel Saw
___Planer
_________________________________________
_________________________________________
_________________________________________
___Drill Press
___Power Feeder
___Radial Arm Saw
___Shaper
___Jointer
___Lathe
___Drum Sander
___Dust Collector
___Spindle Sander
___Table Saw
14. Do you think your purchase represents good value?
___Yes
___No
___Mortiser
___Wide Belt Sander
___Horiz.Boring Machine
___Vacuum Veneer Press
___Other______________________________
15. Would you recommend Grizzly to a friend?
___Yes ___No
16. Would you allow us to use your name as a refer-
ence for Grizzly customers in your area? Note: We
never use names more than three times.
7. How many of your woodworking machines are
Grizzly? _____________
___Yes
___No
8. Which benchtop tools do you own? Check all
that apply.
17.Comments:________________________________
_________________________________________
_________________________________________
_________________________________________
___1"x42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___8" Table Saw
___Scroll Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Spindle/Belt Sander ___Mini Jointer
___10"-12"Thickness Planer
___Other______________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|