Grizzly Mixer H8172 User Manual

MODEL H8172

CEMENT MIXER

OWNER'S MANUAL

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TR9030 PRINTED IN CHINA

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

INTRODUCTION............................................................................................................................... 2

Foreword .................................................................................................................................... 2

Machine Data Sheet................................................................................................................... 2

Contact Info................................................................................................................................ 2

SECTION 1: SAFETY....................................................................................................................... 3

Safety Instructions for Machinery............................................................................................... 3

Additional Safety for Cement Mixers.......................................................................................... 5

SECTION 2: CIRCUIT REQUIREMENTS ........................................................................................ 6

110V Operation.......................................................................................................................... 6

SECTION 3: SETUP......................................................................................................................... 7

Setup Safety............................................................................................................................... 7

Unpacking .................................................................................................................................. 7

Inventory..................................................................................................................................... 8

Assembly.................................................................................................................................... 9

Test Run................................................................................................................................... 11

SECTION 4: OPERATIONS ........................................................................................................... 12

Operation Safety ...................................................................................................................... 12

Operation Tips.......................................................................................................................... 12

SECTION 5: MAINTENANCE ........................................................................................................ 13

Lubrication................................................................................................................................ 13

Cleaning ................................................................................................................................... 13

Drive Belt................................................................................................................................. 13

Wiring Diagram ........................................................................................................................ 14

Parts Breakdown...................................................................................................................... 15

Parts Breakdown...................................................................................................................... 16

Safety Labels Breakdown ........................................................................................................ 17

WARRANTY AND RETURNS........................................................................................................ 18

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

Contact Info

Foreword

If you have any comments regarding this manual,

please write to us at the address below:

We are proud to offer the Model H8172 Cement

Mixer. This machine is part of a growing Grizzly

family of fine machinery. When used according

to the guidelines set forth in this manual, you can

expect years of trouble-free, enjoyable operation

and proof of Grizzly’s commitment to customer

satisfaction.

Grizzly Industrial, Inc.

Technical Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: [email protected]

The specifications, drawings, and photographs

illustrated in this manual represent the Model

H8172 when the manual was prepared. However,

owing to Grizzly’s policy of continuous improve-

ment, changes may be made at any time with no

obligation on the part of Grizzly.

We stand behind our machines. If you have any

service questions or parts requests, please call or

write us at the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 546-9663

Fax: (800) 438-5901

For your convenience, we always keep current

Grizzly manuals available on our website at www.

grizzly.com. Any updates to your machine will be

reflected in these manuals as soon as they are

complete. Visit our site often to check for the lat-

est updates to this manual!

E-Mail: [email protected]

Web Site: http://www.grizzly.com

Machine Data Sheet

��

��^��

-2-

H8172 Cement Mixer

Download from Www.Somanuals.com. All Manuals Search And Download.

��

Safety Instructions for Machinery

��

H8172 Cement Mixer

-3-

Download from Www.Somanuals.com. All Manuals Search And Download.

��

�

��

-4-

H8172 Cement Mixer

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional Safety for Cement Mixers

1. HAZARDOUS DUST. All cement, mortar,

grout, and silicate dusts are hazardous

to respiratory systems. Protect yourself

and any bystanders by always wearing a

respirator approved to guard against these

kinds of dusts.

5. ENTANGLEMENT. The spinning drum and

engaging gears present an entanglement

hazard. When using the cement mixer, tie

back long hair, roll up long sleeves, and

remove loose clothing or jewelry to reduce

the risk of an entanglement injury.

2. PINCH/CRUSHING HAZARD AREA. The

drum has a noticeable ring of gear teeth

around the circumference. The area where

these teeth meet the driving gear is a

severe pinch hazard. Keep hands, fingers,

and all body parts away from these gear

teeth and the driving gear to avoid injury

from this hazard. DO NOT operate the

mixer with the gear cover/guard removed!

6. SERVICE & ADJUSTMENTS. Like all

machines, this machine presents a risk of

injury if it is serviced or adjusted while it

is connected to power. Disconnect power

before doing any service, maintenance, or

adjustments to reduce the risk of acciden-

tal injury.

7. WATER VS. ELECTRIC COMPONENTS.

The electric components are designed to

resist accidental exposure to water, but

they are not waterproof. Avoid intentionally

getting the motor and switch wet to reduce

the risk of shock or equipment damage.

If the internal parts of these components

do get wet, immediately disconnect power

and allow the parts to completely dry

before reconnecting the mixer to the power

supply.

3. CHILDREN. Never allow children to play

on, in, or with the cement mixer.

4. STORAGE. Store the cement mixer with

the drum in the down position and discon-

nected from power to reduce the risk of

children climbing inside and injuring them-

selves.

No list of safety guidelines can be complete.

Every shop environment is different. Always

consider safety first, as it applies to your

individual working conditions. Use this and

other machinery with caution and respect.

Failure to do so could result in serious per-

sonal injury, damage to equipment, or poor

work results.

Like all machinery there is potential danger

when operating this machine. Accidents are

frequently caused by lack of familiarity or

failure to pay attention. Use this machine

with respect and caution to lessen the pos-

sibility of operator injury. If normal safety

precautions are overlooked or ignored, seri-

ous personal injury may occur.

H8172 Cement Mixer

-5-

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 2: CIRCUIT REQUIREMENTS

Circuit Recommendations

110V Operation

We recommend connecting your machine to a

dedicated and circuit that is rated for the amper-

age given below. Never replace a circuit breaker

on an existing circuit with one of higher amper-

age without consulting a qualiﬁed electrician to

Serious personal injury could occur if you

connect the machine to the power source

ensure compliance with wiring codes. If you are

unsure about the wiring codes in your area or

before you have completed the set up pro-

you plan to connect your machine to a shared

cess. DO NOT connect the machine to the

circuit, consult a qualified electrician.

power source until instructed to do so.

110V Circuit.............................................15 Amp

Amperage Draw

Extension Cords

The Model H8172 motor draws the following amps

under maximum load:

•

Use at least a 14 gauge cord that does not

exceed 100 feet in length!

Motor Draw..............................................8 Amps

•

A qualified electrician MUST size cords over

50 feet long to prevent motor damage.

-6-

H8172 Cement Mixer

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 3: SETUP

Setup Safety

Unpacking

Your machine was carefully packaged for safe

transportation. Remove the packaging materials

from around your machine and inspect it. If you

discover the machine is damaged, please imme-

diately call Customer Service at (570) 546-9663

for advice.

This machine presents

serious injury hazards

to untrained users. Read

through this entire manu-

al to become familiar with

the controls and opera-

tions before starting the

machine!

Save the containers and all packing materials for

possible inspection by the carrier or its agent.

Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condi-

tion of your shipment, inventory the contents.

Wear safety glasses dur-

ing the entire setup pro-

cess!

This machine and its com-

ponents are very heavy.

Get lifting help or use

power lifting equipment

such as a fork lift to move

heavy items.

H8172 Cement Mixer

-7-

Download from Www.Somanuals.com. All Manuals Search And Download.

Hardware

Qty

Inventory

Hairpin Cotter Pin (Wheels) .............................. 2

Hex Bolts M8-1.25 x 65 (Leg to Frame)............ 2

Flat Washers 8mm (Leg to Frame)................... 2

Lock Washers 8mm (Leg to Frame) ................. 2

Hex Nuts M8-1.25 (Leg to Frame) .................... 2

Hex Bolt M6-1 x 25 (Plunger Rods) .................. 1

Lock Nut M6-1 (Plunger Rods).......................... 1

Cotter Pin (Plunger Rod)................................... 1

Hex Bolts M8-1.25 x 65 (Bracket to Frame) ..... 2

Flat Washers 8mm (Bracket to Frame)............. 2

Lock Washers 8mm (Bracket to Frame) ........... 2

Hex Nuts M8-1.25 (Bracket to Frame).............. 2

Hex Bolts M8-1.25 x 60 (Bearing Block)........... 1

Flat Washers 8mm (Bearing Block) .................. 1

Lock Washers 8mm (Bearing Block)................. 1

Hex Nuts M8-1.25 (Bearing Block).................... 1

Hex Bolts M8-1.25 x 20 (Upper Bracket) .......... 2

Flat Washers 8mm (Upper Bracket).................. 2

Lock Washers 8mm (Upper Bracket)................ 2

Hex Nuts M8-1.25 (Upper Bracket)................... 2

Phillips Screws M10-1.5 x 20 (Blade/Lower) .... 2

Plastic Washers 10mm (Blade/Lower).............. 2

Flat Washers 10mm (Blade/Lower)................... 2

Lock Washers 10mm (Blade/Lower)................. 2

Hex Nuts M10-1.5 (Blade/Lower)...................... 2

Hex Bolts M8-1.25 x 20 (Drum Pieces)........... 10

Flat Washers 8mm (Drum Pieces).................. 10

Lock Washers 8mm (Drum Pieces) ................ 10

Phillips Screws M10-1.5 x 20 (Blade/Upper) .... 2

Flat Washers 10mm (Blade/Upper)................... 2

Lock Washers 10mm (Blade/Upper)................. 2

Hex Nuts M10-1.5 (Blade/Upper)...................... 2

Hex Bolt M8-1.25 x 65 (Motor Assembly) ......... 1

Flat Washers 8mm (Motor Assembly)............... 3

Lock Washers 8mm (Motor Assembly) ............. 3

Hex Nuts M8-1.25 (Motor Assembly)................ 3

Hex Bolts M8-1.25 x 20 (Tipping Wheel) .......... 2

Flat Washers 8mm (Tipping Wheel).................. 2

Lock Washers 8mm (Tipping Wheel)................ 2

Hex Nuts M8-1.25 (Tipping Wheel)................... 2

After all the parts have been removed from the

carton, you should have:

Main Components (Figures 1 & 2)

Qty

A. Lower Drum................................................ 1

B. Motor Assembly.......................................... 1

C. Tipping Wheel ............................................ 1

D. Upper Drum................................................ 1

E. Support Leg................................................ 1

F. Frame......................................................... 1

G. Axle Bracket ............................................... 1

H. Mixing Blades............................................. 2

I. Wheels ....................................................... 2

J. Bearing Block ............................................. 1

K. Upper Bracket ............................................ 1

L. Gasket (not shown).................................... 1

Figure 1. Inventory components picture 1.

If any nonproprietary parts are missing (e.g. a

nut or a washer), we will gladly replace them; or

for the sake of expediency, replacements can be

obtained at your local hardware store.

NOTICE

Some hardware/fasteners on the inventory

list may arrive pre-installed. Check mount-

ing locations before assuming that any

items from the inventory list are missing.

Figure 2. Inventory components picture 2.

-8-

H8172 Cement Mixer

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Connect the upper and lower plunger rods

together with an M6-1 x 25 hex bolt and M6-

1 lock nut, then insert the cotter pin where

shown in Figure 5. Bend each leg of the cot-

ter pin outward so it can't fall out.

Assembly

To assemble the cement mixer:

1. Insert the wheels on the axles and secure

them in place with the hairpin cotter pins, as

shown in Figure 3.

��

Figure 5. Plunger rod installation.

4. Attach the axle bracket to the frame with two

M8-1.25 x 65 hex bolts on one side and two

8mm flat washers, lock washers, and hex

nuts on the other side (Figure 6).

Figure 3. Wheels installed on axles.

2. Attach the support leg to the frame with two

M8-1.25 x 65 hex bolts on one side and two

8mm flat washers, lock washers, and hex

nuts on the other side (Figure 4).

��

Figure 6. Attaching axle bracket to frame.

Figure 4. Support leg installation.

H8172 Cement Mixer

-9-

Download from Www.Somanuals.com. All Manuals Search And Download.

5. With the help of another person, place the

lower drum on the frame assembly, as shown

in Figure 7. The gear guard MUST remain

installed on the lower drum. If, for any rea-

son, it is not installed in the location shown in

Figure 7, then install it now.

7. Place the upper bracket over the pivot shaft,

and attach the upper bracket to the frame

with two M8-1.25 x 20 hex bolts on one side

and two 8mm flat washers, lock washers, and

hex nuts on the other side (Figure 9).

Gear Guard

Figure 9. Upper bracket installed.

Figure 7. Lower drum on frame.

8. Attach the lower end of the mixing blades

to the lower drum, placing a plastic washer

between the mixing blade and the drum

mounting holes (Figure 10). At each attach-

ment, use an M10-1.5 x 20 Phillips head

screw on one side and a 10mm flat washer,

lock washer, and hex nut on the other side.

Leave the fasteners loose for now.

6. Attach the bearing block to the frame with

one M8-1.25 x 60 hex bolt on one side and

one 8mm flat washer, lock washer, and hex

nut on the other side (Figure 8).

Note: Since these fasteners will be regu-

larly exposed to water, we suggest coat-

ing them with anti-seize or bearing grease

before assembly to prevent them from rusting

together. Repeat this process on the fasten-

ers used in Steps 9–10, as well.

Hex Bolt

M8-1.25 x 60

Figure 8. Bearing block installed over shaft and

attached to frame.

Figure 10. Lower end of mixing blades attached

to lower drum.

-10-

H8172 Cement Mixer

Download from Www.Somanuals.com. All Manuals Search And Download.

9. Place the upper drum on the lower drum with

the gasket between them. Align the arrows

shown in Figure 11, and secure the upper

and lower drum pieces together with ten M8-

1.25 x 20 hex bolts, 8mm lock washers, and

8mm flat washers.

11. Slide the motor assembly onto the bearing

block shaft, then secure the motor assembly

to the frame (Figure 13). Use two 8mm flat

washers, lock washers, and hex nuts on the

motor assembly studs. Slide the remaining

M8-1.25 x 65 hex bolt through the motor

assembly and frame, then secure on the

other side with an 8mm flat washer, lock

washer, and hex nut.

Note: Tighten these hex bolts progressively

in a criss-cross pattern for even tension all

the way around the drum.

Arrows

Figure 13. Motor assembly attached to frame.

12. Attach the tipping wheel to the lower drum

pivot bar (Figure 14). Use two M8-1.25 x

20 hex bolts on one side and two 8mm flat

washers, 8mm lock washers, and M8-1.25

hex nuts on the other side.

Figure 11. Upper drum attached to lower drum.

10. Place a plastic washer between the mounting

holes on the upper end of the mixing blades

and the upper drum. Insert an M10-1.5 x 20

Phillips screw from the outside of the drum

through each mixing blade. Secure each

screw with a 10mm flat washer, lock washer,

and hex nut from the inside (Figure 12).

Completely tighten all the mixing blade fas-

teners now.

Tipping

Wheel

Figure 14. Tipping wheel attached.

Test Run

Once the assembly is complete and you have

read and understand this entire owner's manual,

connect the machine to the power source, then

test run the machine to make sure it runs prop-

erly.

If there is an unusual noise or vibration, stop

using the machine immediately and inspect the

machine for loose fasteners or improperly assem-

bled pieces. If you still cannot remedy a problem,

contact our Tech Support at (570) 546-9663 for

assistance.

Figure 12. Upper part of mixing blades attached

to upper drum.

H8172 Cement Mixer

-11-

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 4: OPERATIONS

Operation Safety

Operation Tips

Follow the tips below when using the cement

mixer:

Damage to your eyes and lungs could result

from using this machine without proper pro-

tective gear. Always wear safety glasses and

a respirator when operating this machine.

•

Before using your cement mixer, coat the

inside of the mixing drum with a light layer of

oil. Refer to Lubrication on Page 13 for more

details.

Spray the inside surface of the cement mixer

with a small amount of water before adding

cement (in addition to the lubrication steps

above). This will make it easier to clean after

operation. Avoid spraying water on the switch

or motor cover!

•

The mixer works more effectively and quickly

when batches are half the maximum recom-

mended mixture load, or if mixture materials

are added slowly (while mixing), rather than

all at one time.

Loose hair and cloth-

ing could get caught in

machinery and cause seri-

ous personal injury. Keep

loose clothing and long

hair away from moving

machinery.

The maximum recommended mixture load is

3.2 cubic feet. This equates to:

— Six 60 lb. bags

— Four 90 lb. bags

NOTICE

If you have never used this type of machine

or equipment before, WE STRONGLY REC-

OMMEND that you read books, trade maga-

zines, or get formal training before begin-

ning any projects. Regardless of the con-

tent in this section, Grizzly Industrial will

not be held liable for accidents caused by

lack of training.

Do not put hands, shovels, or other tools into

the mixing drum while it is turning, or injury

or equipment damage may occur.

Children can hurt themselves if playing on

this mixer. If this machine is not stored in

a locked facility, always disconnect power

when leaving it unattended.

-12-

H8172 Cement Mixer

Download from Www.Somanuals.com. All Manuals Search And Download.

SECTION 5: MAINTENANCE

Cleaning

Always disconnect power

to the machine before

performing maintenance.

Failure to do this may

result in serious person-

al injury.

•

Always unplug the cement mixer before

cleaning.

Avoid getting water on the motor or switch

while cleaning. If you do, allow the compo-

nents to thoroughly dry before plugging in the

motor.

Lubrication

•

The easiest way to clean the drum is by

hosing it out with water. (Cleaning is made

much easier if you follow the Lubrication

procedures in this section before using your

cement mixer.)

Remove the gear cover/guard. Lubricate the driv-

ing gear with a high-quality multi-purpose grease.

Re-install the gear cover/guard before reconnect-

ing your machine to power.

Always clean the mixing drum immediately

after using it. As a general rule, the sooner

you clean, the easier it will be.

•

For tough to remove buildup, use a stiff bristle

brush or a rag to make cleaning easier.

Small, hardened cement splatters usually

can be removed by rubbing with a dry rag.

Hardened cement can be scraped, chiseled

or pounded off with a hammer; however,

these actions WILL damage the surface area

of the drum, making it harder to clean in the

future.

Figure 15. Driving gear.

Before every use, and while the mixing drum and

blades are clean and dry, wipe down the inside

of the mixing drum and blades with a light coat of

motor, hydraulic, or vegetable oil. This will prevent

most cement from sticking to these surfaces and

will make cleaning very easy.

Drive Belt

Avoid getting grease or oil on the drive belt or

pulleys. Check the drive belt, as part of a monthly

inspection for proper tension and belt condition.

Cracking and glazing could result in belt failure.

Replace the belt if such conditions appear.

An alternative to coating the drum interior with oil

is to spray the oil. Since most oils are too thick to

spray, use a mixture of half oil and half diesel fuel.

This is a common spray mixture used in commer-

cial concrete construction to prevent sticking.

H8172 Cement Mixer

-13-

Download from Www.Somanuals.com. All Manuals Search And Download.

Wiring Diagram

��

Figure 16. Switch wiring.

-14-

H8172 Cement Mixer

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts Breakdown

�

��

�

��

�

��

�

��

�

��

�

��

�

��

H8172 Cement Mixer

-15-

Download from Www.Somanuals.com. All Manuals Search And Download.

Parts Breakdown

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

PH8172001

PB03M

UPPER DRUM

58-1

PR15M

EXT RETAINING RING 30MM

INT RETAINING RING 62MM

DUSTPROOF COVER

TAP SCREW M3.5 X 16

SWITCH

HEX BOLT M8-1.25 X 16

RUBBER GASKET

FLAT HD SCR M8-1.25 X 10

BIG COGWHEEL

PR38M

PH8172003

PFH28M

PH8172039

PHTEK2M

PH8172041

PH8172042

PH8172043

PH8172044

PH8172045

PH8172046

PH8172047

PH8172048

PB26M

PH8172005

PH8172006

PH8172007

PB09M

LOWER DRUM

GASKET

UPPER BRACKET

HEX BOLT M8-1.25 X 20

TIPPING WHEEL

STRAIN RELIEF BOLT

POWER CORD

PH8172009

PH8172010

PH8172011

PH8172012

PB10M

STRAIN RELIEF NUT

STRAIN RELIEF RUBBER

STRAIN RELIEF NUT

MOTOR MOUNT BRACKET

HEX BOLT M8-1.25 X 30

INT RETAINING RING 47MM

CIRCLIP 30MM

SUPPORT ARM

UPPER PLUNGER ROD

COMPRESSION SPRING

HEX BOLT M6-1 X 25

FLAT WASHER 8MM

SUPPORT LEG

PW01M

PR25M

PH8172015

PH8172016

PH8172017

PLW04M

PH8172051

P6906

COTTER PIN 4 X 20

LOWER PLUNGER ROD

LOCK WASHER 8MM

HEX NUT M8-1.25

LOCK NUT M6-1

BALL BEARING 6906ZZ

TAP SCREW M5 X 16

END PLATE

PHTEK19M

PH8172054

PH8172055

PH8172056

PH8172057

PH8172058

PC030A

PN03M

GASKET

PLN03M

BELT

PH8172021

PH8172022

PH8172023

PH8172024

PH8172025

PR05M

FRAME

IDLE PULLEY

HEX BOLT M8-1.25 X 70

AXLE BRACKET

MOTOR 110V

S CAPACITOR 30MFD 300VAC

MOTOR FAN

WHEEL

PH8172059

PH8172060

PS35M

HAIR PIN COTTER PIN 3MM

EXT RETAINING RING 15MM

EXT RETAINING RING 42MM

CIRCLIP 42MM

MOTOR COVER

PHLP HD SCR M10-1.5 X 20

PVC WASHER 10MM

LOCK WASHER 10MM

MIXING BLADE

PR62M

PH8172062

PLW06M

PH8172028

PH8172029

PLN04M

O-RING 42 X 2.65

LOCK NUT M8-1.25

BALL BEARING 6202ZZ

DRIVE SHAFT

PH8172064

PN02M

HEX NUT M10-1.5

FLAT WASHER 10MM

SHORT GEAR GUARD

BEARING BLOCK

P6202

PW04M

PH8172032

PH8172033

PH8172034

PH8172035

P6206

PH8172067

PH8172068

PH8172069

PB164M

SLEEVE

DRIVE PINION

GEAR GUARD

LOCK PIN 6 X 30

HEX BOLT M8-1.25 X 70

BALL BEARING 6206ZZ

-16-

H8172 Cement Mixer

Download from Www.Somanuals.com. All Manuals Search And Download.

Safety Labels Breakdown

��

REF PART #

DESCRIPTION

REF PART #

DESCRIPTION

101

102

103

104

PH8172101

PH8172102

PH8172103

PH8172104

MACHINE ID LABEL

105

106

107

108

PH8172105

PH8172106

PH8172107

PPAINT-1

SMALL EYE/LUNG LABEL

SMALL DISCONNECT PWR LABEL

SMALL DRUM PINCH LABEL

LARGE DRUM PINCH LABEL

SMALL READ MANUAL LABEL

MOTOR/WATER SHOCK LABEL

GRIZZLY GREEN TOUCH-UP PAINT

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine

MUST maintain the original location and readability of the labels on the machine. If any label is

removed or becomes unreadable, REPLACE that label before using the machine again. Contact

Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

H8172 Cement Mixer

-17-

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from

the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,

negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty

and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-

ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent

that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.

In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and

any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,

or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then

issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the

carton. We will not accept any item back without this number. Proof of purchase must accompany the

merchandise.

The manufacturers reserve the right to change specifications at any time because they constantly strive to

achieve better quality equipment. We make every effort to ensure that our products meet high quality and

durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

-18-

H8172 Cement Mixer

Download from Www.Somanuals.com. All Manuals Search And Download.

��

�

��

� ��

��

�

��

�

��

� ��

��

�

��

� ��

��

�

��

� ��

��

�

��

�

� ��

��

�

��

� ��

��

�

��

� ��

�

��

�

Download from Www.Somanuals.com. All Manuals Search And Download.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

��^��

��

��^��

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Grizzly Biscuit Joiner G0654 User Manual
Grizzly Grinder D2X User Manual
Hamilton Beach Fryer 35015 User Manual
Honeywell Ventilation Hood HR230 User Manual
Hoshizaki Ice Maker M029 897 User Manual
HP Hewlett Packard Computer Hardware bc1000 User Manual
HP Hewlett Packard Laptop 311245 001 User Manual
Hypertec Network Card SWA1000HY User Manual
IBM Cassette Player 4690 User Manual
iLive Speaker IHS1 IHT3807DT User Manual