MODEL T10722/T10723
FINGERPRINT SAFE
INSTRUCTIONS
For questions or help with this product contact Tech Support at (570) 546-9663 or [email protected]
Introduction
The Model T10722/T10723 Fingerprint Safe (see
Figure 1) provides three methods of securing
your belongings:
Specifications
Overall Dimensions
T10722.................. 133⁄4" W x 10" H x 97⁄8" D
T10723................. 15" W x 113⁄4" H x 113⁄4" D
Maximum Fingerprints..................................... 32
Maximum PIN Numbers .................................... 8
Fireproof ..........................................................No
Required Batteries.........................4 AA, Alkaline
•
•
•
Biometric fingerprint verification
PIN number
Key
This safe features a soft mat inside to protect
secured items, a removable upper shelf, and
mounting holes for securing to a wall or the floor.
Small Item Inventory
Description
Protective Mat.................................................... 1
Anchor Studs M8-1.25 x 50............................... 4
AA Alkaline Batteries......................................... 4
Keys................................................................... 2
Qty
Grizzly cannot replace lost or stolen keys.
Please contact your local locksmith if this
happens.
To reduce the risk of lost or stolen keys,
keep them in a secure location that is sepa-
rate from the safe.
DO NOT store keys inside safe!
Figure 1. Model T10723 Fingerprint Safe.
COPYRIGHT © FEBRUARY, 2013 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
FOR MODELS MANUFACTURED SINCE 01/13 #TS15619 PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
Locking Safe
To lock the safe, make sure the dead bolts are
withdrawn into the door, then close the door and
rotate the door handle counterclockwise 1⁄4 turn.
Most of the safe operations are time sensi-
tive. In general, you will have approximately
five seconds between finishing one action
in the procedure and starting the next.
Otherwise, you will have to start with Step 1
to begin the procedure again.
Unlocking with Fingerprint
1. Press and release the activation button.
Recording Fingerprint
1. With the safe door open, then press and
2. When the fingerprint scanner lights up, place
your fingerprint on the scanner with medium
pressure.
release the reset button.
2. Place your fingertip on the fingerprint scanner
—If your fingerprint was verified, the green
light will flash once, then, after a pause, will
remain lit for approximately five seconds.
During this time, use the door handle to
unlock and open the door.
with medium pressure.
—If properly recorded, the green light will
flash once, then, after a pause, flash again.
—If the red and green lights flash together,
the fingerprint was not recorded. Try again.
—If the red and green lights flash together,
the fingerprint was not verified. Try again.
Recording PIN Number
1. Press and hold the number “1” key on the
PIN pad until the green light flashes once,
then, after a pause, flashes again.
Unlocking with PIN Number
1. Use the PIN pad to enter the PIN number and
press the activation button.
—If the PIN number was verified, the green
light will flash once, then, after a pause, will
remain lit for approximately five seconds.
During this time, use the door handle to
unlock and open the door.
Note: The default factory-set PIN number is
“1234”.
2. Enter the current PIN number and press the
activating button.
—If the red and green lights flash together,
the fingerprint was not verified. Try again.
—If the PIN number was accepted, the green
light will flash once.
Re-setting to Factory Defaults
1. Open the door, then press and hold the reset
button until the following sequence is com-
plete:
3. Enter the new PIN number and press the
activation button.
Note: PIN numbers must be 4–8 numbers in
length.
• One beep with a flash of the green light.
• 15 flashes of the green light.
4. Repeat Step 3.
—If properly recorded, the green light will
flash once, then, after a pause, flash again.
• One beep with a flash of the green light.
The safe is now set to factory defaults without any
fingerprint scans in memory and the PIN number
set to “1234.”
—If the red and green lights flash together,
the PIN number was not recorded. Try
again.
-3-
Model T10722/T10723 (Mfg. Since 01/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Safe
The safe has holes through the back and bottom
for mounting to a wall or floor.
Cleaning
Use a soft cloth moistened with warm water to
clean the painted surfaces of the safe. Do not use
solvents, abrasives, or spray cleaners that can
damage the finish or electronic components.
When mounting to a wall, we recommend secur-
ing 1" wood stock to the wall studs, then securing
the safe to the wood. Make sure the mounting will
hold the weight of the safe and contents, as well
as the forces of opening and locking the door.
Always keep liquids away from the security pad
and the battery compartment to prevent damaging
the electronic components.
Regularly clean the fingerprint scanner lens with a
soft cloth moistened with warm water. Do not use
paper products that can scratch the lens. Do not
use chemicals or spray cleaners that can damage
the lens or electronic components.
Batteries
The electronics of the safe are powered by four
AA batteries. If the fingerprint scanner or PIN pad
does not respond or if the red light on the security
pad stays ON when attempting a procedure, the
batteries need to be replaced.
Use the key to open the safe and replace the
batteries with four high-quality AA alkaline batter-
ies. Refer to Installing Batteries on Page 2 for
detailed instructions.
Note: When the batteries are removed, the record-
ed fingerprint scans and PIN number stay in non-
volatile memory and will remain functional when
the batteries are replaced.
Troubleshooting
Review the troubleshooting and procedures in this section if a problem develops with your safe. If you need
additional help with a procedure, call our Technical Support at (570) 546-9963.
Note: Grizzly cannot replace lost or stolen keys. Please contact your local locksmith if this happens.
Symptom
Possible Cause
Possible Solution
Security pad
1. Batteries are low or dead.
1. Replace batteries.
does not properly
respond to input;
red light stays on.
2. Electronic components are at fault.
2. Replace safe or use keys to operate.
Fingerprint scanner 1. Scanner lens is dirty.
1. Clean scanner lens.
will not record
fingerprint.
2. Fingerprint not readable.
2. Follow the Fingerprint Scanning Tips on Page 2.
3. Security pad memory has reached maximum 3. Erase security pad memory by re-setting to factory
limit of 32 fingerprint scans. defaults.
-4-
Model T10722/T10723 (Mfg. Since 01/13)
Download from Www.Somanuals.com. All Manuals Search And Download.
|