SLIMLINE BENCH GRINDER
MODEL H4378/H4379
INSTRUCTION MANUAL
Model H4379
Model H4378
COPYRIGHT © APRIL, 2002 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
PRINTED IN CHINA.
ONLINE MANUAL DISCLAIMER
THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE
MACHINE CONFIGURATION CAN CHANGE AS PRODUCT IMPROVEMENTS ARE INCORPORATED. IF YOU OWN AN EARLIER VERSION OF THE
MACHINE, THIS MANUAL MAY NOT EXACTLY DEPICT YOUR MACHINE. CONTACT CUSTOMER SERVICE IF YOU HAVE ANY QUESTIONS
ABOUT DIFFERENCES. PREVIOUS VERSIONS ARE NOT AVAILABLE ONLINE.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table Of Contents
PAGE
1.
2.
SAFETY
SAFETY RULES FOR POWER TOOLS ..........................................................2-3
ADDITIONAL SAFETY INSTRUCTIONS FOR GRINDERS................................4
CIRCUIT REQUIREMENTS
110V OPERATION ..............................................................................................5
EXTENSION CORDS ..........................................................................................5
GROUNDING ......................................................................................................5
INTRODUCTION
COMMENTARY....................................................................................................6
ASSEMBLY
3.
4.
UNPACKING ........................................................................................................7
PIECE INVENTORY ............................................................................................7
MOUNTING..........................................................................................................8
TOOL RESTS ......................................................................................................8
EYE SHIELDS......................................................................................................8
OPERATIONS
5.
TEST RUN............................................................................................................9
SAFE GRINDING ..............................................................................................10
WHEEL CARE....................................................................................................10
WHEEL SELECTION ........................................................................................11
WHEEL INSPECTION........................................................................................12
WHEEL MOUNTING ..........................................................................................13
MAINTENANCE
GENERAL ..........................................................................................................14
LUBRICATION ..................................................................................................14
GRINDING WHEELS ........................................................................................14
MAINTENANCE NOTES....................................................................................15
CLOSURE................................................................................................................16
6.
7.
TROUBLESHOOTING ......................................................................................................17
MACHINE DATA ..........................................................................................................18-19
PARTS BREAKDOWN AND PARTS LIST..................................................................20-21
WARRANTY AND RETURNS ..........................................................................................22
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
For Your Own Safety Read Instruction
Manual Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words which are intended to convey the level of
importance of the safety messages. The progression of symbols is described below. Remember
that safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the equipment.
NOTICE
Safety Instructions For Power Tools
1. KEEP GUARDS IN PLACE and in working
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors should be
kept at a safe distance from work area.
order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning on.
6. MAKE WORKSHOP CHILD PROOF with
padlocks, master switches, or by removing
starter keys.
3. KEEP WORK AREA CLEAN. Cluttered
7. DO NOT FORCE TOOL. It will do the job
better and safer at the rate for which it was
designed.
areas and benches invite accidents.
4. DO NOT USE IN DANGEROUS ENVI-
RONMENT. Do not use power tools in
damp or wet locations, or where any flam-
mable or noxious fumes may exist. Keep
work area well lighted.
8. USE RIGHT TOOL. Do not force tool or
attachment to do a job for which it was not
designed.
-2-
H4378/H4379 Slimline Bench Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions For Power Tools
9. USE PROPER EXTENSION CORD. Make
sure your extension cord is in good condi-
tion. Conductor size should be in accor-
dance with the chart below. The amperage
rating should be listed on the motor or tool
nameplate. An undersized cord will cause
a drop in line voltage resulting in loss of
power and overheating. Your extension
cord must also contain a ground wire and
plug pin. Always repair or replace exten-
sion cords if they become damaged.
16. REDUCE THE RISK OF UNINTENTION-
AL STARTING. On machines with magnet-
ic contact starting switches there is a risk of
starting if the machine is bumped or jarred.
Always disconnect from power source
before adjusting or servicing. Make sure
switch is in OFF position before reconnecting.
17. MANY WOODWORKING TOOLS CAN
“KICKBACK” THE WORKPIECE toward the
operator if not handled properly. Know what
conditions can create “kickback” and know
how to avoid them. Read the manual accom-
panying the machine thoroughly.
Minimum Gauge for Extension Cords
LENGTH
AMP RATING
0-6
25ft
18
18
16
14
12
10
50ft 100ft
18. CHECK DAMAGED PARTS. Before fur-
ther use of the tool, a guard or other part
that is damaged should be carefully
checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, bind-
ing of moving parts, breakage of parts,
mounting, and any other conditions that
may affect its operation. A guard or other
part that is damaged should be properly
repaired or replaced.
16
16
16
12
12
10
16
14
14
12
10
No
7-10
11-12
13-16
17-20
21-30
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get
caught in moving parts. Non-slip footwear
is recommended. Wear protective hair cov-
ering to contain long hair.
19. NEVER LEAVE TOOL RUNNING UNAT-
TENDED. TURN POWER OFF. Do not
leave tool until it comes to a complete stop.
11. ALWAYS USE SAFETY GLASSES. Also
use face or dust mask if cutting operation is
dusty. Everyday eyeglasses only have impact
resistant lenses, they are NOT safety glasses.
20. NEVER OPERATE A MACHINE WHEN
TIRED, OR UNDER THE INFLUENCE OF
DRUGS OR ALCOHOL. Full mental alert-
ness is required at all times when running a
machine.
12. SECURE WORK. Use clamps or a vise to hold
work when practical. It is safer than using your
hand and frees both hands to operate tool.
21. NEVER ALLOW UNSUPERVISED OR
UNTRAINED PERSONNEL TO OPER-
ATE THE MACHINE. Make sure any
instructions you give in regards to machine
operation are approved, correct, safe, and
clearly understood.
13. DO NOT OVER-REACH. Keep proper
footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for lubri-
cating and changing accessories.
22. IF AT ANY TIME YOU ARE EXPERIENC-
ING DIFFICULTIES performing the intend-
ed operation, stop using the machine! Then
contact our service department or ask a
qualified expert how the operation should
be performed.
15. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recom-
mended accessories. The use of improper
accessories may cause risk of injury.
H4378/H4379 Slimline Bench Grinder
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Instructions For Grinders
8. DO NOT stand directly in front of grinding
1. ALWAYS WEAR EYE PROTECTION!
wheels when turning machine on.
2. MAKE SURE GRINDER IS SECURED
FIRMLY TO A BENCH OR STAND
BEFORE USE. Any “wobbles” must be
corrected by shimming or blocking before
operation.
9. PERFORM a “ring test” (see page 12) on
grinding wheels to ensure that they are
safe for use. Always inspect grinding
wheels before operation.
10. HOLD THE WORKPIECE FIRMLY
WHILE GRINDING.
3. BEFORE MOUNTING A NEW WHEEL,
BE SURE WHEEL RPM IS RATED AT
AN EQUAL OR HIGHER RPM THAN
THE GRINDER.
11. DO NOT allow your hands to come into
contact with grinding wheels during oper-
ation. Abrasive accessories have the
ability to remove a lot of material, includ-
ing skin, very quickly. However, do not
wear gloves while grinding, they may get
caught in the grinding wheel.
4. DO NOT GRIND ON THE SIDES OF
THE GRINDING WHEELS, unless they
are special wheels designed specifically
for this purpose.
5. ONLY USE FLANGES THAT ARE
INCLUDED WITH THE GRINDER.
12. KEEP TOOL REST AS CLOSE AS
POSSIBLE TO GRINDING WHEEL.
6. WEAR AN APPROVED DUST MASK
OR RESPIRATOR. Grinding operations
produce dust.
13. NEVER GRIND BY PLACING THE
WORKPIECE ON TOP OF THE
WHEEL. The wheel may kick the work-
piece toward the operator. Always grind
on the downward part of the wheel.
7. REPLACE A CRACKED WHEEL IMME-
DIATELY. DO NOT use a grinding wheel
that has cracks or flaws. Before using,
inspect each wheel. Handle wheels care-
fully to avoid bumping or dropping.
To operate this or any power tool safely and
efficiently, become as familiar with it as
possible. The time you invest before you
begin to use your Model H4378/H4379 will
be time well spent. DO NOT operate this
machine until you are completely familiar
with the contents of this manual, or serious
personal injury may occur.
No list of safety guidelines can be com-
plete. Every shop environment is different.
Always consider safety first, as it applies to
your individual working conditions. Use
this and other machinery with caution and
respect. Failure to follow guidelines could
result in serious personal injury, damage to
equipment or poor work results.
-4-
H4378/H4379 Slimline Bench Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: CIRCUIT REQUIREMENTS
110V Operation
This equipment must be
grounded. Verify that any
existing electrical outlet
and circuit you intend to
plug into is actually
grounded. Under no cir-
cumstances should the
grounding pin from any
three-pronged plug be
The Model H4378 is wired for 110V and will draw
2.5 amps. The Model H4379 is wired for 110V and
will draw 3.5 amps. If you operate this machine on
any circuit that is already close to its capacity, it
might blow a fuse or trip a circuit breaker.
However, if an unusual load does not exist and a
power failure still occurs, contact a qualified elec-
trician or our service department.
removed. Serious injury
may occur.
A 10 amp dedicated circuit should be used with
this grinder. Always check to see if your current
wires are capable of handling a 10 amp load. If
you are unsure, consult the advice of a qualified
electrician.
Extension Cords
If you find it necessary to use an extension cord
with the Model H4378/H4379, make sure the cord
is rated Hard Service (grade S) or better. Refer to
the chart in the standard safety instructions to
determine the minimum gauge for the extension
cord. The extension cord must also contain a
ground wire and plug pin. Always repair or replace
extension cords when they become worn or dam-
aged.
Figure 1A. Do not remove grounding pin.
Grounding
In the event of an electrical short, grounding
reduces the risk of electric shock by providing
electric current a path of least resistance. This
tool is equipped with a power cord having an
equipment-grounding conductor. See Figure 1B.
The outlet must be properly installed and ground-
ed in accordance with all local codes and ordi-
nances.
Figure 1B. Typical 110V plug and outlet.
H4378/H4379 Slimline Bench Grinder
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: INTRODUCTION
Most importantly, we stand behind our machines.
Commentary
If you have any service questions or parts
requests, please call or write us at the location
listed below:
We are proud to offer the Grizzly Model
H4378/H4379 Slimline Bench Grinder. The Model
H4378/H4379 is part of a growing Grizzly family of
fine woodworking machinery. When used accord-
ing to the guidelines set forth in this manual, you
can expect years of trouble-free, enjoyable oper-
ation and proof of Grizzly’s commitment to cus-
tomer satisfaction.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
1
The specifications, drawings, and photographs
illustrated in this manual represent the Model
H4378/H4379 as supplied when the manual was
prepared. However, owing to Grizzly’s policy of
continuous improvement, changes may be made
at any time with no obligation on the part of
Grizzly. Whenever possible, though, we send
manual updates to all owners of a particular tool
or machine. Should you receive one, we urge you
to insert the new information with the old and keep
it for reference.
The Model H4378 offers a ⁄3 HP, 3450 RPM
motor and a 6" grinding wheel. The Model H4379
offers a 1⁄2 H.P., 3450 RPM motor and an 8" grind-
ing wheel.
A number of grinding wheels for the Model
H4378/H4379 are available through the Grizzly
catalog.
We are also pleased to provide this manual with
the Model H4378/H4379. It was written to guide
you through assembly, review safety considera-
tions, and cover general operating procedures.
This manual represents our effort to produce the
best documentation possible. If you have any
comments regarding this manual, please write to
us at the address below:
Read the manual before
assembly and opera-
tion. Become familiar
with the machine and its
operation before begin-
ning any work. Serious
personal injury may
result if safety or opera-
tional information is not
understood or followed.
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/O
Bellingham, WA 98227-2069
-6-
H4378/H4379 Slimline Bench Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: ASSEMBLY
Unpacking
Piece Inventory
The Model H4378/H4379 is shipped from the
manufacturer in a carefully packed carton. If you
discover the machine is damaged after you have
signed for delivery, immediately call Customer
Service for advice.
After all the parts have been removed from the
carton, you should have:
• Grinder
• Bolts (4)
• Washers (6)
• Knobs (2)
• Adjustable Rests (2)
• Eye Shields (2)
• Spark Breakers (2)
• Cooling Tray
When you are completely satisfied with the con-
dition of your shipment, you should inventory its
parts.
Some metal parts may
have sharp edges on
them after they are
formed. Please examine
the edges of all metal
parts before handling
them. Failure to do so
could result in injury.
NOTICE
A full parts list and breakdown can be found
toward the end of this manual. For easier
assembly, or to identify specific parts, please
refer to the detailed illustrations at the end of
the manual.
NOTICE
When mounted, the cooling tray can be easi-
ly damaged if the grinder is tipped forward.
H4378/H4379 Slimline Bench Grinder
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting
Tool Rests
The Model H4378/H4379 weighs 22/27 lbs. Make
sure the workbench on which you plan to mount
the grinder is sturdy enough to hold the weight of
the machine and any downward pressure that
may be applied during operation. The workbench
should have a level surface and be heavy, or
attached to the floor, so it will not move during
operation. To mount the grinder:
The tool rest provides a surface that can be used
to support the workpiece during grinding. Certain
types of grinding may require jigs or accessories
to assure the proper angle of the workpiece
against the wheel.
The tool rest attaches to the inward side of the
wheel guard; it should be positioned as close to
the grinding wheel as possible. Insert the 1⁄2" x 1⁄4
"
•
Pick a spot on the workbench that will allow
enough room to move the size of an antici-
pated workpiece around the grinder. The
operator (and possibly bystanders) should
have enough room to stand out of the way in
an emergency.
hex bolt with a flat washer and a lock washer
through the rest support, and thread it into the
tapped hole. Repeat this installation for the oppo-
site side wheel. The tool rest can be adjusted by
loosening these bolts and moving the bracket.
Always retighten before using the machine.
•
Mount the grinder to the workbench with
bolts that are long enough to exceed the
thickness of your workbench and the grinder
base. Secure each bolt with flat washers, a
lock washer and a hex nut. Because sizes
vary for each individual situation, the hard-
ware in this step is not included with the
Model H4378/H4379.
Eye Shields
OSHA requires that the eye shield be positioned
between the grinding wheel and the operator’s
face during grinding. This lessens the possibility
of sparks or metal bits flying directly at the opera-
tor.
•
Mount the grinder in an area with proper
lighting and near electrical outlets. Lighting
should be bright enough to eliminate shadow
and prevent eye strain. Electrical circuits
should be dedicated or large enough to han-
dle amperage requirements. Keep power or
extension cords clear of high-traffic areas.
Observe local electrical codes for proper
installation of new lighting, outlets, or circuits.
Attach each support bracket to the top end of the
wheel rim guards with the knob bolts. Note that
the brackets are slotted to allow up and down
adjustments.
Snap the eye shields into the grooves on the sup-
port brackets. The shields should be able to swiv-
el up and down.
Make your shop “child safe.”
Ensure that your workplace
is inaccessible to children
by closing and locking all
entrances when you are
away. Never allow visitors in
your shop when assembling,
adjusting, or operating
equipment.
-8-
H4378/H4379 Slimline Bench Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: OPERATIONS
NOTICE
Keep loose clothing
The following section was designed to give
rolled up and out of the
way of machinery and
keep hair pulled back.
instructions on the basic operations of this
grinder. However, it is in no way comprehen-
sive of every grinder application. There are
many different grinding wheels and attach-
ments available for grinders. WE STRONGLY
RECOMMEND that you read books, trade
magazines, or get formal training to maxi-
mize the potential of your machine.
Disconnect power to the
machine when perform-
ing any maintenance,
!
assembly
or
adjust-
ments. Failure to do this
may result in serious per-
sonal injury.
Test Run
Once mounting is complete and adjustments are
done to your satisfaction, you are ready to test the
machine.
Wear safety glasses dur-
ing the entire operation
process. Failure to com-
ply may result in serious
personal injury.
Plug the grinder into the power source. Stand
away from the line of rotation of the wheel and
turn the grinder ON. The grinder should run
smoothly with little or no vibration or rubbing nois-
es. Strange or unnatural noises should be investi-
gated and corrected before operating the
machine further. If the grinder seems okay, stay
out of the line of rotation and let it run for 1-2 min-
utes to make sure the wheel is structurally sound.
Using this machine pro-
duces dust which may
cause allergic reactions
and respiratory problems.
Use an approved dust
mask to protect yourself
from these hazards!
If you cannot easily locate the source of an
unusual noise or vibration, feel free to contact our
service department for help.
H4378/H4379 Slimline Bench Grinder
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Safe Grinding
Wheel Care
The grinder is a safe tool when used properly. In
addition to the safety instructions in this manual,
the most important safety consideration is to use
common sense at all times. What may be okay in
one situation, may not be safe in another.
Your safety when grinding depends, on a large
part, on the condition of the wheel during grinding.
A wheel in poor condition presents the possibility
of breaking apart during rotation and injuring the
operator and possibly causing property damage.
Here are some tips to keep in mind while
grinding:
Here are some tips to help you avoid breaking
the wheel:
•
•
Make sure all guards are in place.
•
Always transport, store and handle wheels
with care. Wheels may be damaged if they
are dropped or if heavy objects are stacked
on them.
Remember that grinding often produces
sparks. DO NOT allow anyone to stand in the
path of the sparks. DO NOT grind near flam-
mable liquids or gases.
•
•
Select the right grinding wheel for the job. Do
not grind material that is not designed for the
wheel.
•
•
Maintain proper care of your wheels. Read
the “Wheel Care” instructions for ideas on
how to go about doing this.
Select the right machine for the wheel. A
machine that rotates at a higher RPM than
the wheel is rated for may cause the wheel to
fly apart.
Wear the proper protective clothing.
Remember that particles flying off of a grind-
ing wheel will be traveling very fast—prepare
for this. Wear safety glasses, a dust mask,
earplugs, a leather apron, arm guards, a
hardhat and heavy leather boots.
•
Mount the wheels properly. (See the “Wheel
Mounting” instructions on page 13 for guid-
ance.) Never use a wheel with the wrong
arbor size for the grinder.
•
Grasp the workpiece tight and properly sup-
port it on the tool rest during operation. DO
NOT lean into the workpiece in a manner that
may cause your hands to move into the spin-
ning wheel if the workpiece slips off.
•
•
Do not abuse the wheel by jamming the work
into the grinding wheel with excessive force.
Learn how to use the grinder and the grinding
wheels properly. Ask a trusted person with
experience or consult with your local library to
learn more.
•
•
Concentrate on the task at hand. STOP
grinding if other people are distracting you.
STOP grinding if your mind is on something
else.
•
•
If using coolant, always spin it out of the
wheel before turning off the power.
DO NOT grind on the side of the wheel.
Although side grinding is permissible for
some wheel types, the Model H4378/H4379
is not designed for side grinding.
Grinding on side of the wheel may cause
wheel damage.
-10-
H4378/H4379 Slimline Bench Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
The Grit Size is a number that refers to the size of
the abrasive grain in the wheel. The lower the
number, the coarser the wheel. 10 is a very
coarse wheel for roughing and 220 is usually the
upper range for fine finish work.
Wheel Selection
The Model H4378 only accepts Type-1 wheels
1
with a ⁄2" bore. The Model H4379 only accepts
Type-1 wheels with a 5⁄8" bore.
Grade is an indication of the hardness of the
wheel—“A” being the softest and “Z” being the
hardest.
Aluminum oxide and silicon carbide wheels are
marked in a somewhat uniform manner by all the
major manufacturers. Understanding these mark-
ings will help you understand the capabilities of
various wheels. Always refer to the manufactur-
er’s grinding recommendations when selecting a
wheel for your project.
Bond Type refers to the type of bonding material
used to hold the abrasive material. Most general
purpose wheels will have a “V” indicating Vitrified
Clay is used. Vitrified Clay provides high strength
and good porosity. The other common bond type
is “B” for resin where synthetic resins are used.
These are used to grind cemented carbide and
ceramic materials.
The basic format for wheel numbering is:
Prefix Abrasive
Type
Grit
Size
Grade Bond
Type
There may be other numbers inserted that have
meaning for a particular type of wheel. Refer to
the manufacturer’s technical data for a complete
explanation.
1
A
60
L
V
The Prefix is the manufacturer’s designation for a
particular type.
The most common Abrasive Types used are A for
Aluminum Oxide and C for Silicon Carbide, and
occasionally SG for Seeded Gel.
H4378/H4379 Slimline Bench Grinder
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Wheel Inspection
Before mounting a new grinding wheel, it must be
inspected. Do not assume that a wheel is in sound
condition just because it is new—often, damage
can occur in shipping, with age, or with exposure
to moisture.
STOP
Rated 3500 RPM
Make sure your grinder is not
faster than the rated RPM of this wheel
Type-1
Aluminum
Oxide
60 Grit
Grade L
Vitrified Bond
WARNING
Grinding can be dangerous
Visually inspect this wheel
for cracks, nicks,chips
First, the wheel should be given a Visual
Inspection. Look for any cracks, chips, nicks or
dents in the surface of the wheel. If you see any
of these, DO NOT use the wheel.
Second, the wheel should be given a Ring Test.
This test will give you an indication of any internal
damage that may not be obvious during a visual
inspection.
Figure 2. Ring test tapping locations.
4. An undamaged wheel will emit a clear metal-
lic ring or “ping” sound in each of these spots.
A damaged wheel will respond with a dull
thud that has no clear tone.
To perform a Ring Test:
1. Make sure the wheel that you test is clean
and dry; otherwise, you may get false results.
5. If you determine from the ring test that the
wheel is damaged, DO NOT use it!
2. If size permits, balance the wheel with your
finger in the hole. If this is not possible, hang
the wheel in the air with a piece of cord or
string looped through the hole in the center.
3. At the spots shown in Figure 2, gently tap the
wheel with a light non-metallic device such as
the handle of a screwdriver or a wooden mal-
let.
-12-
H4378/H4379 Slimline Bench Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper/Fiber
Disc
Wheel Mounting
The wheel guard assembly must be removed in
order to mount or dismount a grinding wheel. To
do this:
Flange
Flange
Wheel
1. Disconnect the grinder from the power
supply!
m
i
n
u
n O
m
u
l
x
A
id
e
M
P
T
y
R
p
0
e
-
1
5
3
V
i
t
r
i
f
i
e
d
B
o
n
d
2. Remove the 3 Phillips head screws and nuts
that go through the outer guard. Take off the
outer guard and the rim guard.
Paper/Fiber
Disc
Nut
3. Use a wrench on the nut that holds the wheel
on the arbor. Hold the wheel from turning
with your other hand. Note that the wheel on
the left-hand side of the machine is a left-
handed thread, so loosening it will require
turning it clockwise.
Figure 3. Wheel mounting order.
NEVER assemble a grinding wheel on the
arbor without paper or fiber discs between
the wheel and the flange. Omitting the discs
can put undue stress on the wheel, causing
it to crack and possibly fall apart.
4. Remove the outer wheel flange and the
paper disc. Pull the wheel free from the
arbor. There will also be a paper disc and a
wheel flange on the back side of the wheel.
5. Mount the new wheel in the reverse order or
as shown in Figure 3. Always make certain
there is a paper or fiber disc between the
wheel flanges and the wheel itself. Tighten
the nut snugly but DO NOT over-tighten.
Over-tightening can crack the wheel.
ALWAYS visually inspect and perform a
“ring test” on a wheel before assembly. DO
NOT use damaged wheels!
6. Re-install the guards and shields.
7. Run a new wheel for at least 1-2 minutes
while standing clear of the line of rotation. If a
wheel does have defects it will generally fail
as soon as it gets up to full speed.
H4378/H4379 Slimline Bench Grinder
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: MAINTENANCE
Lubrication
Disconnect power to the
machine when perform-
!
ing any maintenance,
assembly or adjust-
ments. Failure to do this
may result in serious
Sealed and pre-lubricated ball bearings require
no lubrication for the life of the bearings. All bear-
ings are standard sizes, and replacements can be
purchased from our parts department or a bearing
personal injury.
supply store.
General
Always be aware of the condition of your grinder.
Routinely check the condition of the following
items and repair or replace as necessary:
Grinding Wheels
The grinding wheel should be inspected before
every use. Use the “ring test” method from page
12 “Wheel Mounting” instructions to verify the
structural integrity. If using coolant during grind-
ing, always run the wheel for 5-10 minutes at the
end of the operation to remove any coolant from
the wheel. Take care in storing grinding wheels to
keep them free from potential damage by being
dropped or having other items dropped on them.
•
•
•
•
Loose mounting bolts
Worn switch
Worn or damaged cord
Worn or damaged support bearings or guide
bearings
•
•
Damaged grinding wheel
Replace the wheel when the wheel diameter is
reduced to 4" on the Model H4378 and 6" on the
Model H4379. Operating at anything less than this
diameter does not allow the proper alignment of
the tool rest and the eye shield.
Any other condition that could hamper the
safe operation of this machine.
Depending on the type of grinding you do, the
grinding wheel may require periodic dressing.
There are several different types of wheel dress-
ing devices available on the market. Use a suit-
able diamond or silicon carbide stick type dress-
er. Sweep it smoothly and evenly several times
across the face of the wheel. Dressing restores
the abrasive quality of the wheel surface, plus it
will bring the wheel edge back to a square form.
Refer to the instructions that accompany your
dressing accessory for complete details on wheel
dressing.
NOTICE
If the grinder is unmounted from the work-
bench for maintenance, the cooling tray can
be easily damaged if the grinder is tipped for-
ward.
-14-
H4378/H4379 Slimline Bench Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance Notes
Maintenance Performed
Date
Approximate Hours Of Use
H4378/H4379 Slimline Bench Grinder
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8: CLOSURE
We recommend you keep a copy of our current
The following pages contain general machine
data, parts diagrams/lists, a troubleshooting guide
and Warranty/Return information for your Model
H4378/H4379.
catalog for complete information regarding
Grizzly's warranty and return policy. If you need
additional technical information relating to this
machine, or if you need general assistance or
replacement parts, please contact the Service
Department listed in Section 3: Introduction.
If you need parts or help in assembling your
machine, or if you need operational information,
we encourage you to call our Service Department.
Our trained service technicians will be glad to help
you.
Additional information sources are necessary to
realize the full potential of this machine. Trade
journals, woodworking magazines, and your local
library are good places to start.
If you have comments dealing specifically with
this manual, please write to our Bellingham,
Washington location using the address in Section
3: Introduction.
The Model H4378/H4379 was specifically
designed for grinding. DO NOT MODIFY
AND/OR USE THIS MACHINE FOR ANY
OTHER PURPOSE. Modifications or
improper use of this tool will void the war-
ranty. If you are confused about any aspect
of this machine, DO NOT use it until all
your questions have been answered or
serious personal injury may occur.
We have included some important safety mea-
sures that are essential to the operation of this
machine. While most safety measures are gener-
ally universal, Grizzly reminds you that each
workshop is different and safety rules should be
considered as they apply to your specific situa-
tion.
Operating this equipment creates the poten-
tial for flying debris to cause eye injury.
Always wear safety glasses or goggles
when operating equipment. Everyday glass-
es or reading glasses only have impact
resistant lenses, they are not safety glasses.
Be certain the safety glasses you wear meet
the appropriate standards of the American
National Standards Institute (ANSI).
Like all power tools, there is danger asso-
ciated with the Model H4378/H4379.
Accidents are frequently caused by lack of
familiarity or failure to pay attention. Use
this tool with respect and caution to lessen
the possibility of operator injury. If normal
safety precautions are overlooked or
ignored, serious personal injury may
occur.
-16-
H4378/H4379 Slimline Bench Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
This section covers the most common problems encountered in grinding and what to do about them. Do
not make any adjustments until grinder is unplugged and moving parts have come to a complete stop.
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
1. Check power line for proper voltage.
Motor will not start.
1.
2.
Low voltage.
Open circuit in motor or loose 2.
connections.
Inspect all lead connections on motor for loose or open connec-
tions.
Motor will not start; fuses or 1.
Short circuit in line cord or plug. 1.
Short circuit in motor or loose 2.
connections.
Inspect cord or plug for damaged insulation and shorted wires.
Inspect all connections on motor for loose or shorted terminals or
worn insulation.
circuit breakers blow.
2.
3.
Incorrect fuses or circuit break- 3.
ers in power line.
Install correct fuses or circuit breakers.
Motor overheats.
1.
Motor overloaded.
1.
Reduce load on motor.
Motor stalls (resulting in 1.
blown fuses or tripped cir-
Short circuit in motor or loose 1.
connections.
Inspect connections on motor for loose or shorted terminals or
worn insulation.
cuit).
2.
3.
Low voltage.
Incorrect fuses or circuit breakers 3.
in power line.
2
Correct the low voltage conditions.
Install correct fuses or circuit breakers.
4.
Motor overloaded.
4.
Reduce load on motor.
Machine slows when oper- 1.
ating.
Depth of cut too great.
1.
Slow down the rate of movement of the workpiece into wheel.
Wavy condition on surface 1.
Machine vibrating.
Workpiece not being held firmly. 2.
Wheel face uneven.
Wheel is too hard.
1.
Make sure machine is securely mounted on a solid surface.
Use a holding device to firmly retain the workpiece.
Dress the grinding wheel.
of workpiece.
2.
3.
4.
3.
4.
Use softer wheel, or reduce the feed rate.
Lines on surface of work- 1.
piece. 2.
Impurity on wheel surface.
Workpiece not being held tightly. 2.
1.
Dress the grinding wheel.
Use a holding device to firmly retain the workpiece.
Burning spots or cracks in 1.
Improper type of grinding wheel. 1.
Try a wheel which is softer style or a coarser grit.
the workpiece.
2.
3.
Improper feed rate.
Coolant required.
2.
3.
Slow down the rate of movement of the workpiece into wheel.
Add optional coolant system or introduce coolant by hand.
Wheel dulls quickly, grit falls 1.
Depth of cut too great.
Wheel is too soft.
Wheel diameter too small.
Bad wheel dress.
1.
2.
3.
4.
5.
Slow down the rate of movement of the workpiece into wheel.
Wheel too soft for the material being ground, select harder bond.
Replace the wheel.
Dress the wheel.
Consult manufacturer of grinding wheel.
off.
2.
3.
4.
5.
Defective wheel bonding.
Wheel clogs and workpiece 1.
Wheel is too hard.
Feed rate too slow.
Bad wheel dress.
Coolant required.
1.
2.
3.
4.
Wheel too hard for the material being ground, select softer bond.
Increase the rate of movement of the workpiece into wheel.
Dress the wheel.
shows burn marks.
2.
3.
4.
Add optional coolant system or introduce coolant by hand.
Disconnect power to the
machine when perform-
ing any maintenance,
assembly or adjust-
ments. Failure to do this
may result in serious
personal injury.
!
H4378/H4379 Slimline Bench Grinder
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901
MODEL H4378 SLIMLINE BENCH GRINDER
Design Type.......................................................................... Bench Model
Overall Dimensions:
Height ..............................................................................................10"
Width............................................................................................185⁄16"
Depth ..............................................................................................10"
Shipping Weight ........................................................................25 lbs.
Net Weight..................................................................................22 lbs.
Box Size ......................................................171⁄2" L x 91⁄4" W x 101⁄2" H
Footprint..................................................................................8" x 75⁄16"
Arbor ................................................................................................1⁄2
Wheel Size ................................................................................6" x 3⁄4
"
"
Motor:
Type....................................................TEFC Capacitor-Start Induction
Horsepower..................................................................................1⁄3 HP
Phase / Voltage ....................................................Single-Phase ⁄ 110V
Amps (No Load) ..............................................................................2.5
Cycle / RPM ........................................................60 Hertz ⁄ 3450 RPM
Bearings ......................................Shielded & Permanently Lubricated
Features:
......................................................................................Wheel Flanges
............................................................................................Tool Rests
..............................................................................Rocker-Type Switch
....................................................Extended Wheel-to-Motor Clearance
........................................................................Convenient Water Tray
..............................Included 36 Grit Aluminum Oxide Grinding Wheel
..............................Included 60 Grit Aluminum Oxide Grinding Wheel
Specifications, while deemed accurate, are not guaranteed.
-18-
H4378/H4379 Slimline Bench Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE DATA
SHEET
Customer Service #: (570) 546-9663 • To Order Call: (800) 523-4777 • Fax #: (800) 438-5901
MODEL H4379 SLIMLINE BENCH GRINDER
Design Type.......................................................................... Bench Model
Overall Dimensions:
Height............................................................................................101⁄2
"
Width............................................................................................187⁄16"
Depth ..........................................................................................1013⁄16"
Shipping Weight ........................................................................30 lbs.
Net Weight..................................................................................27 lbs.
Box Size..........................................................18" L x 11" W x 111⁄4" H
Footprint..................................................................................8" x 75⁄16"
Arbor ................................................................................................5⁄8
Wheel Size ................................................................................8" x 3⁄4
"
"
Motor:
Type....................................................TEFC Capacitor-Start Induction
Horsepower ................................................................................1⁄2" HP
Phase / Voltage ....................................................Single-Phase ⁄ 110V
Amps (No Load) ..............................................................................3.5
Cycle / RPM ........................................................60 Hertz ⁄ 3450 RPM
Bearings ......................................Shielded & Permanently Lubricated
Features:
......................................................................................Wheel Flanges
............................................................................................Tool Rests
..............................................................................Rocker-Type Switch
....................................................Extended Wheel-to-Motor Clearance
........................................................................Convenient Water Tray
..............................Included 36 Grit Aluminum Oxide Grinding Wheel
..............................Included 60 Grit Aluminum Oxide Grinding Wheel
Specifications, while deemed accurate, are not guaranteed.
H4378/H4379 Slimline Bench Grinder
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
15
27
28
43
24
2
14
4
6
26
25
18
48
46
30
19
20
21
13
44
48
34
CBB60
32
31
33
20
47
29
35
22
41
23
19
C
O
G
6
N
2
I
37
0
R
2
A
-
2
E
R
B
S
S
A
B O
B
38
42
39
36
15
43
14
13
18
13
9
6
5
g
n
W
i
d
h
e
n
e
i
r
l
s
r
G
a
s
n
'
16
d
4
b
o
T
B
o
2
m
i
B
b
o
n
e
s
L
t
d
M
P
.
R 6 1
7
44
3
-20-
H4378/H4379 Slimline Bench Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
MODEL H4378 PARTS
Ref# Part#
Description
Ref# Part#
Description
02 PH4378002 COVER
03 PN06
27 PH4378027 GRINDER WHEEL
28 PN26
HEX NUT 1⁄2
"
LEFT HAND HEX NUT 1⁄2
"
04 PH4378004 FLANGE
29 PH4378029 WIRE
05 PH4378005 GRINDER WHEEL
06 PH4378006 FLANGE
30 PH4378030 STRAIN RELIEF
31 PH4378031 BACK B0DY
32 PH4378032 CAPACITOR CBB60
07 PH4378007 WHEEL GUARD
09 PH4378009 SPARK BREAKER
33 PS01
PHLP HD SCR 10-24 X 1⁄2
"
13 PW06
FLAT WASHER 5⁄16"
34 PH4378034 MACHINE ID LABEL
35 PH4378035 FRONT BODY
14 PH4378014 KNOB SCREW 1⁄4"-20 X 3⁄8
15 PH4378015 EYESHIELD
"
36 PS22
PHLP HD SCR 10-24 X 5⁄8
"
16 PH4378016 ADJUSTABLE REST
37 PH4378037 SWITCH
38 PH4378038 BASE PLATE
39 PH4378039 PAD
18 PB15
19 PH4378019 BUSHING
20 P6202 BALL BEARING 6202-2RS
HEX BOLT 5⁄16"-18 X 3⁄8
"
41 PH4378041 COOLING TRAY
21 PH4378021 MOTOR STATOR
22 PH4378022 WIRE NUT
23 PH4378023 MOTOR SHAFT
24 PH4378024 SPARK BREAKER
25 PH4378025 ADJUSTABLE REST
26 PH4378026 WHEEL GUARD
42 PW03
43 PH4378043 EYESHIELD CLIP
44 PS06
46 PH4378046 STRAIN RELIEF PLATE
47 PH4378047 CAPACITOR BRACKET
48 PS01
FLAT WASHER #10
PHLP HD SCR 10-24 X 3⁄8
"
PHLP HD SCR 10-24 X 1"
MODEL H4379 PARTS
Ref# Part#
Description
Ref# Part#
Description
02 PH4379002 COVER
03 PN04
27 PH4379027 GRINDER WHEEL
28 PN27
HEX NUT 5⁄8
"
LEFT HAND HEX NUT 5⁄8
"
04 PH4379004 FLANGE
29 PH4378029 WIRE
05 PH4379005 GRINDER WHEEL
06 PH4379006 FLANGE
30 PH4378030 STRAIN RELIEF
31 PH4378031 BACK B0DY
32 PH4378032 CAPACITOR CBB60
07 PH4379007 WHEEL GUARD
09 PH4378009 SPARK BREAKER
33 PS01
PHLP HD SCR 10-24 X 1⁄2
"
13 PW06
FLAT WASHER 5⁄16"
34 PH4379034 MACHINE ID LABEL
35 PH4378035 FRONT BODY
14 PH4378014 KNOB SCREW 1⁄4"-20 X 3⁄8
15 PH4378015 EYESHIELD
"
36 PS22
PHLP HD SCR 10-24 X 5⁄8
"
16 PH4378016 ADJUSTABLE REST
37 PH4378037 SWITCH
38 PH4378038 BASE PLATE
39 PH4378039 PAD
18 PB15
19 PH4379019 BUSHING
20 P6203 BALL BEARING 6203-2RS
HEX BOLT 5⁄16"-18 X 3⁄8
"
41 PH4378041 COOLING TRAY
21 PH4379021 MOTOR STATOR
22 PH4378022 WIRE NUT
23 PH4379023 MOTOR SHAFT
24 PH4378024 SPARK BREAKER
25 PH4378025 ADJUSTABLE REST
26 PH4379026 WHEEL GUARD
42 PW03
43 PH4378043 EYESHIELD CLIP
44 PS06
46 PH4378046 STRAIN RELIEF PLATE
47 PH4378047 CAPACITOR BRACKET
48 PS01
FLAT WASHER #10
PHLP HD SCR 10-24 X 3⁄8
"
PHLP HD SCR 10-24 X 1"
H4378/H4379 Slimline Bench Grinder
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, spe-
cial, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,” which must be clearly posted on the outside as well as the inside of the car-
ton. We will not accept any item back without this number. Proof of purchase must accompany the mer-
chandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
-22-
H4378/H4379 Slimline Bench Grinder
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name ____________________________________________________________________________________
Street ____________________________________________________________________________________
City ______________________________________________________________State________Zip_________
Phone Number_______________________E-Mail_______________________FAX________________________
MODEL # H4378/H4379 Slimline Bench Grinder Serial# ___________________ Order# ________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of
course, all information is strictly confidential.
1.
How did you learn about us?
___Advertisement
___Catalog
___Friend
___Card Deck
10.
Which benchtop tools do you own? Check all that apply.
___World Wide Web
___1" x 42" Belt Sander
___5" - 8" Drill Press
___8" Table Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Mini Jointer
___6" - 8" Grinder
___Mini Lathe
___10" - 12" Thickness Planer
___Scroll Saw
___Spindle/Belt Sander
___Other__________________________________________________
Which of the following magazines do you subscribe to.
2.
___American Woodworker
___Cabinetmaker
___Practical Homeowner
___Shop Notes
___Today’s Homeowner
___WOOD
___Wooden Boat
___Woodshop News
___Woodsmith
___Woodwork
___Woodworker
___Woodworker’s Journal
___Workbench
___Other__________________________________________________
How many of the machines checked above are Grizzly? ____________
___Family Handyman
___Fine Homebuilding
___Fine Woodworking
___Home Handyman
___Journal of Light Construction
___Old House Journal
___Popular Mechanics
___Popular Science
11.
12.
Which portable/hand held power tools do you own? Check all that apply.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
___Popular Woodworking
___Other__________________________________________________
Which of the following woodworking/remodeling shows do you watch?
___Miter Saw
3.
___Other__________________________________________________
What machines/supplies would you like Grizzly Industrial to carry?
___Backyard America
___Home Time
___The New Yankee Workshop
___This Old House
13.
___The American Woodworker
___Woodwright’s Shop
__________________________________________________________
__________________________________________________________
What new accessories would you like Grizzly Industrial to carry?
__________________________________________________________
__________________________________________________________
What other companies do you purchase your tools and supplies from?
__________________________________________________________
__________________________________________________________
Do you think your purchase represents good value?
___Other__________________________________________________
What is your annual household income?
4.
5.
14.
15.
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
What is your age group?
___20-29
___30-39
___40-49
___50-59
___60-69
___70 +
16.
17.
18.
6.
7.
8.
How long have you been a woodworker?
___Yes
Would you recommend Grizzly Industrial to a friend?
___Yes ___No
___No
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
How would you rank your woodworking skills?
Would you allow us to use your name as a reference for Grizzly customers
in your area? Note: We never use names more than three times.
___Simple
___Intermediate
___Advanced
___Master Craftsman
___Yes
___No
What stationary woodworking tools do you own? Check all that apply.
19.
Comments:_________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
__________________________________________________________
___Air Compressor
___Band Saw
___Drill Press
___Drum Sander
___Dust Collector
___Horizontal Boring Machine
___Jointer
___Panel Saw
___Planer
___Power Feeder
___Radial Arm Saw
___Shaper
___Spindle Sander
___Table Saw
___Lathe
___Mortiser
___Vacuum Veneer Press
___Wide Belt Sander
___Other__________________________________________________
How many of your woodworking machines are Grizzly? _____________
9.
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|