MODEL H6167
2000 LB. WINCH
w/STEEL CABLE
INSTRUCTIONS
To reduce the risk of serious personal injury
while using this winch:
1. Always wear ANSI approved eye protec-
tion when operating the winch.
2. Be sure the cable is not damaged. If the
cable shows any signs of fraying or any
other damage, do not use the winch.
3. Do not exceed the pulling capacities of
the winch.
4. Do not stand in line with cable while
operating the winch. If the cable breaks
it will whip back along this line.
5. Keep all loose clothing, hair, jewelry
and hands away from winch during
operation.
Figure 1. Model H6167.
If you need help with your new item, call our Tech
Support at: (570) 546-9663.
6. Use a spotter to help ensure safety
when using the winch. Be sure the spot-
ter is out of the way of the vehicle and
the cable before operating the winch.
7. Do not replace the cable with one of
lesser strength.
8. Do not loop the cable around an object
and back to itself. Use a chain or towing
strap if necessary.
Specifications
Horizontal Pulling Capacity ................. 2000 Lbs.
Cable .............................................32' x 1⁄4" Steel
Ratchet .................Two-Direction with Freewheel
Gear Ratios ........................................4:1 and 8:1
Mounting Bolt Hole Size..................................3⁄8
"
Bolt Grade .............................................. Grade 8
9. Do not use the winch to lift vertical
loads. It is designed for horizontal loads
only. Lifting vertical loads may cause
the winch to fail and drop the load.
10. Do not use the winch to support loads
for long periods of time.
11. Avoid dynamic loading caused by yank-
ing or jerking of the cable. This may
cause the winch to release its load.
CoPyRiGHT © oCToBeR, 2008 By GRizzLy inDuSTRiaL, inC.
WARNINg: NO pORTION OF THIS MANUAL MAy BE REpRODUCED IN ANy SHApE
OR FORM WITHOUT THE WRITTEN AppROvAL OF gRIzzLy INDUSTRIAL, INC.
#JB11231 PRinTeD in CHina
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove the lock nut that secures the handle
gear Ratios
to the shaft.
The Model H6167 has a two available gear ratios.
By placing the handle on one of the two shafts,
you can change the gear ratio to a 4:1 or an 8:1
ratio.
3. Remove handle and handle bracket, reposi-
tion them to the necessary shaft, making sure
to align the flats on the shaft with the flats
on the handle bracket, then replace the lock
nut.
To change the gear ratio:
1. use Figure 4 to determine which handle
position is required for the desired ratio.
—if the handle is already placed in that posi-
Damage to your eyes could
result from using this item
without proper protective
eyewear.
tion, no further action is required.
—if the gear ratio you want requires the han-
dle to be repositioned, continue to Step 2.
Operations
1. Move the ratchet control lever to the free-
wheel position to feed slack until the cable
hook reaches the load.
4:1 Ratio
Shaft
8:1 Ratio
Shaft
Handle Bracket
Handle
2. Hook the load, then move the lever to the
winching position. Crank the handle to move
the load. once the load is secured by other
means, release the hook from the load.
Lock nut
Figure 4. Gear ratios.
-3-
H6167 2000 LB. Winch w/Steel Cable
Download from Www.Somanuals.com. All Manuals Search And Download.
"UY $IRECT AND 3AVE WITH 'RIZZLY® n 4RUSTEDꢀ 0ROVEN AND A 'REAT 6ALUEꢁ
6ISIT /UR 7EBSITE 4ODAY !ND $ISCOVER
7HY 'RIZZLY® )S 4HE )NDUSTRY ,EADERꢀ
s 3%#52% /2$%2).'
s /2$%23 3()00%$ 7)4(). ꢃꢄ (/523
s %ꢂ-!), 2%30/.3% 7)4(). /.% (/52
ꢂ/2ꢂ
#ALL 4ODAY &OR !
&2%%
&ULL #OLOR #ATALOG
Download from Www.Somanuals.com. All Manuals Search And Download.
|