MODEL T21543/
T21544/T21545
ELECTRONIC KEYPAD SAFE
INSTRUCTIONS
Specifications
Overall Dimensions:
Safe Keys
The safe keys can be used to unlock the safe door
instead of your personal code or the emergency
code.
T21543.................... 14" W x 101⁄4" D x 10" H
T21544.................14" W x 173⁄4" D x 781⁄4" H
T21546.................16" W x 133⁄4" D x 121⁄4" H
Locking Devices ..........Electronic Keypad or Key
Power Requirement....................4 "AA" Batteries
if you have used the key to unlock the safe door,
you will have to use it to re-lock the door so that
you can remove the key from the door.
Inventory
However, the key cannot be used to re-lock the
safe door if a code was used to open it.
Keys................................................................... 2
"AA" Batteries .................................................... 4
Hex Wrench 4mm.............................................. 1
Mounting Hardware ................................... Varies
Refer the next section for detailed instructions
regarding using the safe key.
Mounting
Opening Safe Door the First Time
There are mounting holes provided through the
safe walls that are accessed from inside the safe.
Use the provided hardware or fasteners of your
choice to firmly anchor your safe to a solid and
stable surface. Models T21543 and T21545 are
designed to mount on a wall or shelf, and the door
must open horizontally to operate correctly. Model
T21544 is a floor safe and the door must open
vertically for proper operation.
1. After you remove your new safe from the
shipping box, detach the two safe keys from
the outside of the safe.
2. Use a 4mm hex wrench to remove one of the
button head cap screws that secure the brass
nameplate, then let the nameplate swing
down to expose the keyhole (see Figure 1).
NOTICE
Key
NEvER keep the safe keys inside the safe.
We recommend that you keep each key in
a separate secure and accessible location.
In the event that both your personal and
emergency codes have been forgotten or
misplaced, these physical keys will be the
only way to unlock your safe.
nameplate
Hand indent
Figure 1. nameplate moved out of the way to
If you need help with your new safe, call our Tech
Support at: (570) 546-9663.
use the key (Model T21543 shown).
COPyRigHT © DECEMBER, 2009 By gRizzLy inDUsTRiAL, inC.
WARNINg: NO PORTION OF ThIS MANUAL MAY bE REPRODUCED IN ANY ShAPE
OR FORM WIThOUT ThE WRITTEN APPROvAL OF gRIzzLY INDUSTRIAL, INC.
#Ts12358 PRinTED in CHinA
Download from Www.Somanuals.com. All Manuals Search And Download.
To change the emergency code:
batteries
The digital keypad and locking mechanism require
four "AA" batteries to operate. Under normal con-
ditions, new or fully charged batteries should last
approximately one year.
1. With the safe door unlocked, push the " "
*
key twice. The LED window will display the
word "PROG".
2. When the LED window clears, enter the cur-
if the batteries have lost their charge and the digi-
tal keypad does not respond, use the safe key to
open the door and replace the batteries.
rent emergency code.
—if the current emergency code is entered
successfully, the LED window will display
the word "NEW". Continue to Step 3.
Note: The emergency code is stored in perma-
nent memory so that, in the event the digital key-
pad loses power, this code will remain the same.
—if the code is not entered correctly, the
word "Error" will be displayed. Restart the
procedure with Step 1.
Maintenance
Wipe the surfaces of your safe with a clean,
slightly damp cloth. if the door develops a squeak,
open it and apply a drop or two to the hinge rod
contact points.
NOTICE
If you change the emergency code from
the factory default and forget or misplace
it, you will not be able to reset or change
it. Always record the new emergency code
below, then store these instructions in a
secure location.
Troubleshooting
Problem: The door will not close all the way.
Solution: Make sure there is nothing obstructing
the door. if the locking rods protrude to
the left of the safe door, use the safe
key to fully retract them back into the
door.
3. After the LED window clears, enter the new
six-digit emergency code. The LED window
will display the word "AGAIN".
Problem: The digital keypad does not respond.
Solution: The batteries may be low or fully dis-
charged. Use the safe key to open the
door and replace the batteries with
new or fully charged ones.
4. When the LED window clears again, re-enter
the new code.
—if the second entry of the new emergency
code matches the first entry, the LED win-
dow will display the word "DONE" and this
procedure is complete.
Problem: The personal code does not open the
door.
Solution: Use the safe key or emergency code to
open the door, then follow the Personal
Code instructions on Page 2 to create
a new personal code.
—if the second entry of the new emergency
code does not match the first entry, the
word "Error" will appear in the LED win-
dow and the previous emergency code will
remain active. Re-start at Step 1 to change
the current emergency code.
Problem: The personal and emergency codes
have been forgotten or misplaced.
Solution: Use the safe key to open the door, then
follow the Personal Code instructions
on Page 2 to create a new personal
code. The emergency code cannot be
reset or changed if it is forgotten or
misplaced.
Emergency Code:
-3-
T21543/T21544/T21545 Electronic Keypad safe
Download from Www.Somanuals.com. All Manuals Search And Download.
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
~Since 1983~
Visit Our Website Today For
Current Specials!
ORDER
24 HOURS A DAY!
1-800-523-4777
Download from Www.Somanuals.com. All Manuals Search And Download.
|