MODEL H8067
FLAT IRON STYLE
MANDOLIN KIT
OWNER'S MANUAL
COPYRIGHT © NOVEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL8554 PRINTED IN JAPAN
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
SECTION 1: SAFETY....................................................................................................................... 2
SECTION 2: INTRODUCTION ......................................................................................................... 3
Foreword .................................................................................................................................... 3
Contact Info................................................................................................................................ 3
SECTION 3: PARTS INVENTORY................................................................................................... 4
Inventory..................................................................................................................................... 4
Supplies/Tools............................................................................................................................ 4
Identification ............................................................................................................................... 5
SECTION 4: SANDING .................................................................................................................... 6
Body ........................................................................................................................................... 6
Neck ........................................................................................................................................... 6
Fretboard.................................................................................................................................... 6
SECTION 5: ASSEMBLY................................................................................................................. 7
Neck to the Body........................................................................................................................ 7
Fretboard.................................................................................................................................. 10
Shaping Neck........................................................................................................................... 11
Shaping Fretboard ................................................................................................................... 11
Final Sanding ........................................................................................................................... 12
Finishing................................................................................................................................... 13
Nut............................................................................................................................................ 14
Tailpiece................................................................................................................................... 14
Tuning Machines...................................................................................................................... 15
Fitting Bridge............................................................................................................................ 15
Placing Bridge.......................................................................................................................... 16
Winding Strings........................................................................................................................ 17
String Height ............................................................................................................................ 17
Tuning ...................................................................................................................................... 18
SECTION 6: REFERENCE INFO ................................................................................................... 19
Accessories.............................................................................................................................. 19
WARRANTY AND RETURNS........................................................................................................ 21
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
Always wear safety glasses or goggles when operating equipment. Everyday glasses or read-
ing glasses are not safety glasses. Be certain the safety glasses you wear meet the appropri-
ate standards of the American National Standards Institute (ANSI).
Because there are various ways to cut and join wood, you can make substitutions for the methods
stated in this plan. We try to suggest the easiest methods possible. However, only you know your
skills with each piece of machinery. Never compromise your safety by using a cutting method
with which you are not comfortable. Instead, find an alternative approach that will yield the same
result.
These instructions assume that you are intimately familiar with the safe operation and use of wood-
working machinery and woodworking tools, and understand the techniques used to reproduce this
project. If you do not qualify for both of these criteria, STOP building this project for your own
safety. Read and understand the owners manual for the machinery you intend to use, take a wood-
working class or visit your local library for more information. Woodworking machinery and tools
are inherently dangerous because they use sharp edges that can and will cause serious personal
injury including amputation and death. Do not underestimate the ability of these tools and machin-
ery to cause injury. Never operate any tool without all guards in place and always wear approved
safety glasses. For your own safety, please heed this warning.
-2-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INTRODUCTION
Foreword
Contact Info
We are proud to offer the Model H8067 Flat Iron
Style Mandolin Kit. This kit is a part of a growing
Grizzly family of fine woodworking projects. When
assembled according to the guidelines set forth in
this manual, you can expect years of enjoyment
from your mandolin.
If you have any comments regarding this manual,
please write to us at the address below:
Grizzly Industrial, Inc.
C
/O
Technical Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: [email protected]
We are pleased to provide this manual for the
Model H8067 Flat Iron Style Mandolin Kit. It was
written to guide you through assembly, review
safety considerations, and cover general informa-
tion. It represents our effort to produce the best
documentation possible.
We stand behind our products. If you have any
service questions or parts requests, please call or
write us at the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
-3-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: PARTS INVENTORY
Inventory
9
11
REF PART #
DESCRIPTION
QTY
1
10
1
PH8067001 Mandolin Body
PH8067002 Neck
2
1
3
PH8067003 Fretboard
PH8067004 Bridge
1
13
12
4
1
5
PH8067005 Tuning Machines
PH8067006 Tailpiece
PH8067007 Nut
2
Figure 2. Additional components.
6
1
7
1
8
PH8067008 Endpin
1
Supplies/Tools
9
PH8067009 Dowels
2
10
11
12
13
PH8067010 Strings
8
The majority of the wood components in this kit
come fully machined and ready for assembly. A
small amount of sanding and finish work is need-
ed to complete the mandolin.
PH8067011 Bushings
PH8067012 #3 x 3/4" SS Screw
PH8067013 #1 x 3/8" SS Screws
8
1
14
Recommended Tools & Supplies:
•
•
•
•
•
Wood Glue—Titebond Original Wood Glue
#80 to #320 Sanding Paper
Flexible Sanding Block
“000” Grade Steel Wool
Clamps or Rubber Strips (made from cut up
inner tubes)
1
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Electric/Cordless Drill
3
Drill Bit (1/16")
8
7
5
Small Brad Nails
Wire Cutters
Razor Blades
Chisel
Phillips Screwdriver
Masking Tape
Lightweight Hammer
Rubber Dead Blow Hammer
Steel Straight Edge
Sharp Pencil
File Assortment
Finishing Materials
Electronic Tuner
4
6
Figure 1. Boxed components.
Coat Hanger
NIOSH Approved Respirator
ANSI-Approved Safety Glasses
-4-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification
Bridge
Tailpiece
Fret
Nut
Neck
Endpin
Figure 3. Model H8067 main features.
Tuner or Tuning Machine
Tuning Peg
Headstock
Figure 4. Model H8067 headstock features.
-5-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: SANDING
Body
Neck
The mandolin neck has been rough sanded at
the factory. Personalize the fretboard and neck
headstock with additional cutting, inlay, or design
work before final sanding.
The mandolin body was rough sanded at the
factory. To get a good finish the body must be
sanded further with a series of sandpaper grits.
To sand the mandolin body:
Note: Take your time and consider testing your
designs in scrap wood before performing the
work on the actual fretboard and headstock.
1. Wear a NIOSH-approved respirator and
a ANSI-approved safety glasses when
sanding wood!
Wait until the fretboard is installed before
sanding the neck.
2. Use a sanding block with #150 grit alumi-
num-oxide sanding paper to sand the man-
dolin body until there is a consistent scratch
pattern on the entire surface. Sand as little
as possible in the neck area at this time
Fretboard
Note: When hand sanding, always sand in
the same direction as the wood grain.
The fretboard requires no sanding.
Note: Sanding the fretboard will affect the play-
ability of the mandolin and could lead to perma-
nent damage.
3. Resand the entire mandolin body with #220
grit sanding paper and lightly round over the
sound hole and edges of the body.
4. Wipe the mandolin body with a damp cloth to
“raise” the wood grain.
5. Wait until the wood is dry and resand the
entire body with #220 grit sandpaper.
6. Repeat Steps 4-5.
7. Fill the wood pores in the back of the rim with
a paste filler according to the manufacturer's
instructions. DO NOT fill the grain in the
mandolin top (soundboard).
8. When the paste filler is dry, use “000” grade
steel wool to remove the residue and polish
the wood surface.
-6-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: ASSEMBLY
Neck to the Body
A precise fit is important for the neck-to-body
joint. This joint affects the placement of the strings
and bridge, and these determine the sound qual-
ity of the mandolin. Dry fit and check all the parts
before gluing.
Components and Hardware Needed:
Qty
Neck .................................................................. 1
Body .................................................................. 1
Dowels............................................................... 2
Tailpiece ............................................................ 1
Nut ................................................................... 1
Figure 6. Adjusting the fit of the neck.
3. Dry fit the neck and mark the center of both
To install the neck:
ends of the body, and the neck.
1. Test fit the neck by pushing the dowels into
the body of the mandolin and sliding the neck
onto the dowels as shown in Figure 5. DO
NOT glue the joint at this time.
4. Place a straightedge across your center
marks as shown in Figure 7.
Center
Line Marks
Figure 5. Test fitting the neck.
Figure 7. Checking neck and body alignment
2. Check for gaps between the body and the
along center line.
neck.
—If center marks are aligned, move to Step
6.
—If the neck fits tightly, go on to Step 3.
—If there are gaps, remove the neck and
dowels, and hold sandpaper on the surface
of the mandolin body with the grit facing out
(See Figure 6). Rub the neck up and down
on the sandpaper until the neck conforms
to the body shape.
—If the center marks are not aligned, move
to Step 5.
-7-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Align the neck by using the sanding tech-
nique described in Step 2. Apply extra pres-
sure toward the part of the neck that needs to
be shifted.
Note: Check alignment frequently. A little bit
of sanding can cause large adjustments.
6. Place the tailpiece on the edge of the
soundboard and align it to the center mark.
1
7. Use a screw or drill a hole with a ⁄16" bit to
Fretboard
Nut
mark the centers of the screw holes (Figure
8) and then set the tailpiece to the side.
Figure 9. Marking the nut position.
9. Remove the nut and place the fretboard on
the neck, aligning it with the top of the line
drawn in Step 8.
10. Mark the edge of the fretboard binding onto
both sides of the neck, drawing a line 11⁄2
"
from the body toward the headstock as
shown in Figure 10.
Figure 8. Marking tailpiece mounting holes.
Note: The tailpiece will not be installed until
after the finish is applied to the mandolin (see
Page 14), but the alignment of the tailpiece is
easier before final sanding.
8. Place the nut at the end of the neck so it is
straight across as shown in Figure 9, and
draw a line along the bottom edge of the nut.
Do not place the nut on the pegboard, the
piece that slopes downward from the neck.
Figure 10. Marking fretboard binding edges onto
neck.
-8-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Remove the fretboard, turn the mandolin
over, and draw a line on the end of the neck
where the body intersects it as shown in
Figure 11. Extend this line around the neck
using a straightedge.
15. Apply a thin coat of wood glue into the dowel
holes in the mandolin body, insert the dowels
and wipe away excess glue.
16. Spread a thin layer of wood glue on the heel
of the neck, the dowels, and the body where
it will connect to the neck.
17. Press the neck firmly onto the dowels.
18. Use rubber strips or clamps to hold the neck
in place until the glue dries (Figure 13).
Note: If using clamps, use wooden blocks
and pads to protect the instrument.
Figure 11. Marking bottom of neck.
12. Remove the neck from the body.
13. Use a 4-in-1 shoe rasp to file the end of the
neck down to the line you drew in Step 10 as
shown in Figure 12. Shape both sides of the
neck, then sand smooth with #220 grit sand-
paper.
Figure 13. Example of gluing the neck.
19. Scrape away excess glue with a sharp knife
when it sets, then allow the glue to dry for 24
hours before the next step.
Figure 12. Shaping end of neck.
14. File the end of the neck down to the line you
marked in Step 11. This will make the bottom
of the neck even with the mandolin body.
-9-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Fretboard
Components and Hardware Needed:
Qty
Mandolin Body................................................... 1
Fretboard........................................................... 1
To attach the fretboard to the neck:
1. Check to see if the neck is flat by laying it
down on an even surface.
Brad Nails
Figure 15. Trimming brad nails.
—If neck is flat, move on to Step 2.
—If there are gaps between the surface and
the neck, place sandpaper, grit side up, on
the flat surface and rub the neck on the
sandpaper (as shown in Figure 14) until
the neck is flat.
4. Center the fretboard on the neck, aligning the
top with the line drawn in Step 2.
Note: The neck is wider than the fretboard
and will be shaped to match later.
5. Place a wooden block on the fretboard and
tap the block lightly with a hammer to leave
marks in the back of the fretboard.
1
6. Drill ⁄8" deep holes in the marks made in
Step 5.
Note: To ensure that you do not drill through
the fretboard, use a depth stop or wrap tape
around the bit 1⁄8" from the tip.
7. Spread a light layer of glue on the flat surface
of the neck and the back of the fretboard,
then position the fretboard on the neck using
the brad nails as guides.
Figure 14. Flattening the neck.
2. Drill positioning holes near the ends of the
surface of the neck using a drill bit that is
slightly smaller than the brad nails used for
positioning.
8. Use rubber strips or clamps to hold the
fretboard in place until the glue dries.
Note: Use wooden blocks and pads between
the clamps and the neck to protect the instru-
ment.
3. Nail the brads into the positioning holes and
use wire cutters to cut the heads off no more
than an 1⁄8" above the surface of the neck as
shown in Figure 15.
9. Scrape away the excess glue when it sets,
then allow the glue to dry for 24 hours.
-10-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Fill the wood pores in the neck with a paste
filler according to the manufacturer's instruc-
tions.
Shaping Neck
The rest of the neck must be shaped to match the
width of the fretboard and then sanded smooth.
8. When the paste filler is dry, use “000” grade
steel wool to remove the residue and polish
the wood surface.
Components and Hardware Needed:
Qty
Mandolin Body................................................... 1
To shape and sand the neck:
Shaping Fretboard
1. Wear a NIOSH-approved respirator and
ANSI-approved safety glasses during the
next step to protect against dust!
The binding and fret ends must be filed down.
Components and Hardware Needed:
Mandolin Body................................................... 1
Qty
2. Use a 4-in-1 shoe rasp to shape the neck
until it matches the width of the fretboard
(Figure 16).
To clean up the binding and fret ends:
1. Use a fine machinist's file to make the binding
even with the fretboard surface as shown in
Figure 17. File up to the edge of the frets.
Note: File the binding at an angle so you do
not damage the fretboard surface.
Figure 16. Shaping the neck.
3. Use a flexible sanding block with #150 grit
aluminum-oxide sanding paper to sand the
neck until there is a consistent scratch pat-
tern on the entire surface.
Note: When hand sanding, always sand in
the same direction as the wood grain.
Figure 17. Filing fretboard binding.
4. Resand the neck with #220 grit sanding
paper.
5. Wipe the neck with a damp cloth to raise the
wood grain.
6. Wait until the wood is dry and resand the
neck with #220 grit sandpaper. Dampen
again and resand.
-11-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Use a fine flat file to angle the metal fret ends,
as shown in Figure 18.
Final Sanding
Components and Hardware Needed:
Qty
Mandolin Body................................................... 1
To prepare the mandolin for finishing:
1. Inspect the entire mandolin under bright
lights and take note of any glue residue,
dents, scratches, and areas needing further
sanding.
2. Carefully scrape away any glue residue with
a sharp chisel held perpendicular to the sur-
face as shown in Figure 20.
Figure 18. Filing fret ends.
Note: File enough of the fret ends so they are not
sharp, as shown in Figure 19.
Figure 20. Example of removing glue residue.
3. Wear a NIOSH-approved respirator and
ANSI-approved safety glasses during the
next step to protect against dust!
Figure 19. Example of correctly angled fret
ends.
4. Use #220 grit sandpaper to smooth any flaws
found when inspecting the mandolin.
5. Final sand the entire mandolin, except the
fretboard, with #320 grit sandpaper.
-12-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Finishing
Most finishes are hazard-
ous to your health. Wear a
NIOSH/OSHA approved res-
pirator with particulate and
gas/vapor filters, safety
glasses, rubber gloves, and
work in a well ventilated area
when finishing.
Finishing supplies are not included with this
mandolin kit. Finishing options include stains,
lacquers, varnishes and oil finishes. All can be
applied by spray or brush. Finish materials and
books on finishing instruments can be ordered
through Grizzly Industrial or numerous luthier sup-
ply catalogs.
Components and Hardware Needed:
Mandolin Body................................................... 1
Qty
4. Apply several thin coats of the finish (follow-
ing the manufacturer's instructions). Multiple
thin coats usually produce a better quality
finish than one heavy coat.
To finish the mandolin:
1. Mask off the surface of the fretboard. Carefully
press all the masking tape edges securely
to the fretboard. The finish coat should not
be allowed to seep under edges, or flood-
corners, and places where the frets meet the
fingerboard.
5. Hang the instrument in a dust free area to
dry.
6. When finishing is complete, remove the
masking tape from the fretboard.
7. Carefully scrape any excess finish off the
2. Form a piece of wire into a U shaped hanger
fretboard with a razor blade.
with hooks on both ends.
Painting/Finishing Tips
3. Thread the hooks through the upper pegholes
Dust particles suspended in the air will settle
on wet finishes, causing less than satisfactory
results. To avoid this problem:
and hang the instrument in the finish room.
•
•
•
•
Leave the finishing room undisturbed for 24
hours prior to applying the finish.
Avoid making unnecessary movements upon
entering the finish room.
Apply the finish to the desired mandolin parts
and immediately leave the finish room.
DO NOT return to the room until the speci-
fied drying time has elapsed.
Figure 21. Instrument ready to be finished.
-13-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Nut
Tailpiece
The nut holds the peghead end of the strings the
correct distance above the frets. It is not neces-
sary to cut the string notches in the nut.
The tailpiece holds and separates the ends of the
strings.
Components and Hardware Needed:
Qty
Components and Hardware Needed:
Mandolin Body................................................... 1
Nut ................................................................... 1
Qty
Mandolin Body................................................... 1
Tailpiece ............................................................ 1
#1 x 3/8" Stainless Steel Screws........................ 2
#3 x 3/4" Stainless Steel Screw.......................... 1
Endpin ............................................................... 1
To install the nut:
1. Use a chisel to carefully scrape all of the fin-
ish out of the nut slot (Figure 22). DO NOT
remove any wood from the nut slot.
To install the tailpiece:
1. Place the tailpiece on the edge of the
soundboard and align the screw holes with
the marks made earlier.
2. Secure the tailpiece to the mandolin with two
#1 x 3/8" screws as shown in Figure 23.
Nut Slot
Figure 22. Example of cleaning out the nut slot.
2. Spread a thin layer of glue in the nut slot and
on the end of the fretboard.
Figure 23. Tailpiece components.
3. Place the nut in the nut slot and hold it in
place with rubber strips or clamps until the
glue dries.
3
3. Insert a #3 x /4" screw through the endpin
(strap button).
Note: Use wood blocks and pads between
the clamps and the neck to protect the instru-
ment.
4. Screw the endpin into the center hole of the
tailpiece.
4. Wipe away excess glue before it sets, then
allow the glue to dry for 24 hours.
-14-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Tuning Machines
Fitting Bridge
Components and Hardware Needed:
Qty
Components and Hardware Needed:
Mandolin Body................................................... 1
Bridge................................................................ 1
Qty
Mandolin Body................................................... 1
Tuning Machines ............................................... 2
Bushings............................................................ 8
#1 x 3/8" Stainless Steel Screws...................... 10
This mandolin has a scale of 350mm, which
means that the bridge will be placed 350mm
(13.8") from the nut. Mandolin bridges are not
glued into place, but are held in place with the
string pressure, so final placement of the bridge
occurs when the strings are tuned.
To install the tuning machines:
1. Place the eight bushings in the pegholes as
shown in Figure 24.
To fit the bridge to the soundboard:
1. Place the bridge on a piece of sandpaper,
grit side up, 350mm from the nut as shown in
FIgure 26.
Bushing
Direction of
Sanding
Figure 24. Peghead bushings.
2. Use a rubber dead blow hammer or a wood
block to seat the bushings so the bushing
flanges are flush with the peghead surface.
3. Turn the mandolin over and insert the tuning
machines into the back of the pegholes.
Figure 26. Fitting the bridge to the soundboard.
4. Attach both tuning machines to the peghead
with the #1 x 3/8" screws (Figure 25).
2. Hold the sandpaper firmly (to avoid marring
the finish), and move the bridge back and
forth between the sound hole and the tail-
piece.
3. Remove the sandpaper and place the bridge
on the soundboard. Look for gaps between
the bridge and the soundboard. Repeat Step
2 until there are no gaps.
Figure 25. Tuning machines installed
in the peghead.
-15-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Make sure that the bridge is located 350mm
(13.8") from the nut and 175mm (6.89") from
the 12th fret. (See Figure 28).
Placing Bridge
Components and Hardware Needed:
Qty
Mandolin Body................................................... 1
Bridge................................................................ 1
To place the bridge:
1. Use a narrow file to make slots in the bridge.
Angle the slots toward the tailpiece. See
Figure 27 for an example of string spacing on
the bridge.
Note: Make the bridge slots the same depth
as the nut slots. If you make the slots too
deep, it will be harder to make adjustments.
Figure 28. Bridge placement.
6. Set the position of the bridge by lightly touch-
ing the 1st string directly above the twelfth
fret and pluck the string to play a harmonic
note.
�����
�
�����
�
7. Now pluck the string while holding it against
the twelfth fret. If this note is sharper than
the note played in Step 6, move the bridge
toward the tailpiece. If this note is flat in com-
parison, move the bridge toward the neck.
�����
�
������
�
Note: This can also be done with an elec-
tronic tuner by tuning the harmonic note to
be exactly in tune and then adjusting the
bridge until the note played in Step 7 is also
in tune.
Figure 27. String slot example.
2. Lay the bridge flat on the mandolin so the
taller side points toward the top of the body.
3. Follow the Winding Strings instructions on
Page 17.
4. Slide the strings into their slots and tune.
-16-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Winding Strings
String Height
Correct string height is crucial to prevent fret buzz
and maximize playability. The string height is
measured from the top face of the fret to the bot-
tom of the string (Figure 30).
Components and Hardware Needed:
Qty
Mandolin Body................................................... 1
Strings ............................................................... 8
Bridge................................................................ 1
To install the mandolin strings:
1. Bend the looped end of the strings and
place them over the hooks on the tailpiece
as shown in Figure 29. Work from the thin-
nest string (E string-treble) to the thickest (G
string-bass).
String Height
Fretboard
String
Fret
Tip: Try bending the loops over the end of a
sharpened pencil. You will have more control
than with your fingers.
Figure 30. String height measurement.
�
�
�
�
Measurements are taken at the following loca-
tions along the first and eight strings.
•
•
1st fret
12th fret
To check the string height at the first fret:
Figure 29. String placement.
1. Measure the string height at the first fret. The
2. Route the strings through the tailpiece, over
the bridge, and into the inside of the tuning
posts.
1
first string measurement should be /64", the
8th string should be 1/64"-1/32".
—If the string heights are correct (Figure
31), measure the string heights at the 12th
fret.
Note: Allow enough string slack for 2-3 com-
plete winds around the tuning peg.
3. Turn the knobs to tighten the strings.
—If the string heights are incorrect at the 1st
fret, this is an indication that the string nut
grooves must either be deeper or shal-
lower.
-17-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Mandolin
Body
String Nut
8th String:
1⁄64"–1⁄32"
Tuning
Correct tuning is the most important aspect of
performance for a mandolin. If the mandolin is
not in tune with itself, or with other instruments in
an ensemble, the resulting music will not please
the ear. The standard mandolin tuning notes are
shown in Figure 33.
1st String: 1⁄64"
1st Fret
Figure 31. Correct 1st fret string heights.
To check the string height at the 12th fret:
G
A
4
2
D
E
3
1
1. Measure the string height at the 12th fret
(Figure 32). The first string measurement
should be /32-7/64"; the 8th string should be
3
7/64"-9/64".
Mandolin
8th String:
Body
Figure 33. Standard tuning notes.
7⁄64"–9⁄64"
Important issues to consider when tuning a
mandolin:
•
Get into the habit of tuning the mandolin
every time you play it.
•
Always tune the strings “up.” The final tuned
tension of each string should be reached by
tightening the string, not by loosening it. If
the string is tensioned too far, release the
tension and tune “up” again.
1st String: 3⁄32"-7⁄64"
12th Fret
Figure 32. Correct 12th fret string heights.
•
The easiest way to tune a mandolin is using
an electronic tuner such as the Grizzly
H3097 Chromatic Tuner shown on Page 19.
—If the string height is correct, then continue
to the next sub-section.
—If the string height is incorrect at the 12th
fret, the bridge slots must be deeper or
shallower.
-18-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: REFERENCE INFO
H1302—Standard Earmuffs
Accessories
H4979—Deluxe Twin Cup Hearing Protector
H4977—Work-Tunes Radio Headset Earmuffs
Protect yourself comfortably with a pair of cush-
ioned earmuffs. Especially important if you or
employees operate for hours at a time.
G7984—Face Shield
H1298—Dust Sealed Safety Glasses
H1300—UV Blocking, Clear Safety Glasses
H2347—Uvex® Spitfire Safety Glasses
H0736—Shop Fox® Safety Glasses
H1302
Safety Glasses are essential to every shop. If
you already have a pair, buy extras for visitors
or employees. You can't be too careful when it
comes to shop safety!
H4979
H4977
H1300
H1298
G7984
Figure 36. Our most popular earmuffs.
H5097—Constructing a Bluegrass Mandolin
This beautifully detailed manual gives clear, step
by step directions from raw materials to a magnifi-
cently finished mandolin through the use of simply
stated texts, photos and templates. Spiral bound
and includes 19 full-sized blueprints covering
each phase of construction. 56 pages.
H0736
H2347
Figure 34. Our most popular safety glasses.
H3097—Chromatic Tuner
An absolute must for any guitar player, this tuner
allows you to tune your acoustic or electric guitar
dead on. Includes 9V battery.
H5332—Titebond Original Wood Glue, 16 Oz.
The industry standard for luthiers.
Figure 37. Model H5332 Titebond Wood Glue.
Figure 35. Model H3097 Chromatic Tuner.
-19-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
H5750—Vinyl Washcoat/Sealer, 1Qt
H5751—Nitrocellulose Lacquer, Gloss, 1 Qt
H5752—Nitrocellulose Lacquer, Gloss, 1 Gal
H5753—Nitrocellulose Lacquer, Satin, 1 Qt
H5754—Nitrocellulose Lacquer, Satin, 1 Gal
H5755—Retarder for Lacquer, 1 Qt
H5756—Natural Filler, 1 Pint
H5757—Mahogany Filler, 1 Pint
H5759—Filler Reducer, 1Qt
McFadden's nitrocellulose lacquer is the leading
lacquer used by custom guitar builders. It sprays
and buffs really well and is capable of giving you
a finish that looks "wet."
H2499—Small Half-Mask Respirator
H3631—Medium Half-Mask Respirator
H3632—Large Half-Mask Respirator
H3633—Disposable Cartridge Filter Pair
H3635—Disposable Cartridge Filter Pair
This lightweight elastomeric facepiece has cradle
suspension, easy adjust headstraps and low
profile for greater field of vision and compatibility
with normal use of glasses or goggles. Purchase
cartridges separately depending upon intended
application.
Model H3633 protects against organic vapor,
sulfur dioxide, hydrogen chloride and chlorine.
Model H3635 protects against all particulate
aerosols.
Figure 38. Model H5750-59 McFadden's
Lacquers and Fillers.
Figure 40. Half-mask respirator and disposable
G8979—6 Pc. Mini File Set
cartridge filters.
For delicate work, this mini file set includes an
assortment of oval, flat, half round, round, trian-
guular and square files with comfortable handles.
Figure 39. Model G8979 mini file set.
-20-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
-21-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
-22-
H8067 Flat Iron Style Mandolin Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
�������������
���������������������������������������������������������������������������������� �
������������������������������������������������������������������������������������
����� ����������������������� ������������������������������� ���� ���������������������
���������������������������� ������ ������������������������ ���������������������������
���������������������������� ������������������������������� ���������������������������
�������������������������������������������������������������������������������������������������������������������
����������������������������������������������������������������������������������
��� ���������������������������
�
����� ��������������
� ���� �������
� ���� ��������
����� �������
����� ������
�
����� ����������
��� �����������������������������������������������������
���� �������������
���� ���������������
���� �����������
���� �����������������
���� ���������������
���� �������������������
���� �������������������
���� �����������������
���� �����������������
���� ����������
���� �����������������
���� ����
���� �����������
���� �������������
���� ���������
���� �����
���� �������������������
���� ����������������������
���� ����������
���� �������������������
���� ��������
���� ��������
���� ���������������
���� ��������������������
���� ������
���� ����
���� ����������
���� �����������������
���� ������������
��� �������������������������������������
�
����� ����������������
� ���� ����������������
����� ���������������
����� ��������
�
����� ����������������
� ���� ����������������
��� �����������������������
�
����� ������
� ���� ������
� ���� ������
����� �����
����� ���
�
����� ������
��� ������������������������������������������������
����� ���������� ����� ���������� ����� ������������
�
� �������������
��� �����������������������������������������������
����� ���� ����� ����
�
����� ����
� �������
� ������
� ������
��� ���������������������������������������������������
��� ����������������������������������������������������
����������
����������
��� ��������������������������������������������������������������������������������������
�������������������������������������������� ���������� � ������
�
���� �������������������������������������������������������������������������������
� ����������������������������������������������������������������������������������
� ����������������������������������������������������������������������������������
Download from Www.Somanuals.com. All Manuals Search And Download.
����������������������
�����
�����
����
������������������������
�������������
��������������������������
����������������������
�����������������������������������
�����������������������������������
�������������������������������������
��������������������������������������
��������������������������������������
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
�����������������������������������������������������������������������
�������������������������������������
������������������������������������
�����������������
��������������������������������
���������������������������������
����
�����������������
����
������������������
Download from Www.Somanuals.com. All Manuals Search And Download.
|