MODEL T10050
RIGHT ANGLE
IRON BENDER
INSTRUCTIONS
Damage to your eyes, face, and hands could
result from using this item without proper
protective gear, such as safety glasses or a
face shield, and gloves.
Figure 1. Model T10050.
Inventory (Figure 2)
A. Bender (not shown).................................... 1
B. Bender Handle ........................................... 1
C. Work Stop Rod........................................... 1
D. Hex Bolts M10-1.5 x 40 (Handle)............... 2
E. Flat Washers 10mm (Handle) .................... 2
F. Work Stop................................................... 1
G. Work Stop Knob......................................... 1
H. Hex Nut M12-1.75 (Work Stop Rod).......... 1
B
C
H
F
G
d
Specifications
e
Maximum Workpiece Thickness........ 3 Ga.(15⁄64")
Maximum Workpiece Width..............................4"
Machine Weight.........................................81 lbs.
Figure 2. inventory.
If you need help with your new machine, call our
Tech Support at: (570) 546-9663.
Copy RiGHT © July, 2008 By G Rizzly iNdu STRial, iNC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JB10791 pRiNTed i N CHiNa
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Thread the work stop knob into the work stop,
then slide the work stop onto the work stop
rod (Figure 7).
Assembly
The Model T10050 requires only minimal assem-
bly before use.
Work Stop
To assemble the machine:
1. Connect the bender handle to the machine
with the M10-1.5 x 40 hex bolts and 10mm
flat washers (Figure 5).
Hex Bolt
x2
Work Stop Rod
Knob
Figure 7. Work stop.
Flat Washer
Handle
Figure 5. Attaching handle.
2. insert the stop rod with the M12-1.75 hex nut
into the base. Tighten the hex nut against the
base to secure it (Figure 6).
Hex Nut
Work Stop Rod
Figure 6. Attaching work stop rod.
-3-
T10050 Right angle iron Bender
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting
Operations
once you have confirmed that your machine is
assembled and functioning properly, mount it to a
workbench through the holes in the base. Be sure
the workbench will remain stable when bending
force is applied to the machine. if necessary,
anchor the workbench to a wall or the floor to
provide the necessary stability.
Creating Bends
1. lift the clamp cam shaft to release the clamp
die. Rotate the clamp die as necessary to
accommodate the thickness of your work-
piece, then slide the clamp cam shaft back
into the base (Figures 10 & 11).
The strongest mounting option is a "Through
Mount" where holes are drilled all the way through
the workbench, and hex bolts, washers, and
hex nuts are used to secure the machine to the
workbench.
Cam Shaft
7dai
die
;aViꢀLVh]Zg
-ACHINE "ASE
Figure 10. Lifting clamp cam shaft and die.
7ORKBENCH
;aViꢀLVh]Zg
AdX`ꢀLVh]Zg
=ZmꢀCji
Figure 8. example of a through mount setup.
another option for mounting is a "direct Mount"
where the machine is simply secured to the work-
bench with a lag screw.
AV\ꢀHXgZl
Figure 11. Clamp die positions.
;aViꢀLVh]Zg
-ACHINE "ASE
7ORKBENCH
Figure 9. example of a direct mount setup.
-4-
T10050 Right angle iron Bender
Download from Www.Somanuals.com. All Manuals Search And Download.
2. place the workpiece into the clamp and adjust
the workpiece position as needed. Rotate the
clamp cam shaft to clamp the workpiece
(Figure 12).
4. use the handle to bend the workpiece to the
desired angle (Figure 14).
Figure 14. Bending workpiece.
Figure 12. Clamping workpiece.
5. loosen the bending plate and clamp cam
shaft to release the workpiece (Figure 15).
—if the clamp die does not move far enough
to fully clamp the workpiece, repeat Steps
1 & 2.
88L
3. adjust the bending plate to support the work-
piece while bending (Figure 13).
8L
Figure 15. Releasing workpiece.
Figure 13. Tightening bending plate.
NOTICE
Use the machine only as it is intended to be
used. Adding cheater bars or other meth-
ods of increasing leverage may damage the
machine and will void the warranty.
-5-
T10050 Right angle iron Bender
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Bend the workpiece to the desired angle,
then slide the angle stop against the bender
base. Turn the angle stop to lock it in position
(Figure 17).
Repetitive Bends
To ensure consistent and accurate bends when
performing multiple, identical operations, use the
work stop and angle stop.
To use the work stop and angle stop:
7ZcYZgꢀ7VhZ
1. place the workpiece in the machine as need-
ed, then slide the work stop against the end
of the workpiece. Tighten the work stop knob
(Figure 16).
6c\aZꢀHide
8L
Figure 17. Using angle stop.
Ldg`ꢀHide
3. With each new workpiece, place the work-
piece against the work stop, clamp it, then
bend it until the moving bender base contacts
the angle stop.
Ldg`e^ZXZ
Figure 16. Using work stop.
-6-
T10050 Right angle iron Bender
Download from Www.Somanuals.com. All Manuals Search And Download.
parts Breakdown & List
.
'&
-
'%
+
&'
'*
*
'%
'(
')"&
&(
&.
&."&
&,
,
&*
)
')
'
''
&+
&
(
&)
&)"&
&-
REF PART #
DESCRIPTION
REF PART #
DESCRIPTION
1
PT10050001
PT10050002
PT10050003
PT10050004
PT10050005
PT10050006
PT10050007
PT10050008
PT10050009
PT10050012
PT10050013
PT10050014
BODY
15
16
17
18
19
PT10050015
WORK STOP
2
CRANK
PT10050016
PSW03-1
WORK STOP ROD
KNOB M10-1.5 x 35
PLASTIC GRIP
3
HANDLE
4
STATIONARY JAW
BENDING PLATE
BENDING PLATE KNOB
PT10050018
PB31M
5
HEX BOLT M10-1.5 X 40
FLAT WASHER 10MM
6
19-1 PW04M
7
BENDING PLATE LEADSCREW
CLAMP DIE
20
21
22
23
24
PSB14M
PRP08M
PN09M
CAP SCREW M8-1.25 X 20
ROLL PIN 6 X 30
8
9
CLAMP CAM SHAFT
COVER PLATE
HEX NUT M12-1.75
CAP SCREW M10-1.5 X 25
HEX BOLT M10-1.5 X 35
HEX NUT M10-1.5
12
13
14
PSB64M
PB14M
END PLATE
ANGLE STOP
24-1 PN02M
25 PT10050025
14-1 PSN05M
SQUARE NUT M12-1.75
PIVOT PIN
-7-
T10050 Right angle iron Bender
Download from Www.Somanuals.com. All Manuals Search And Download.
"UY $IRECT AND 3AVE WITH 'RIZZLY® n 4RUSTEDꢀ 0ROVEN AND A 'REAT 6ALUEꢁ
6ISIT /UR 7EBSITE 4ODAY !ND $ISCOVER
7HY 'RIZZLY® )S 4HE )NDUSTRY ,EADERꢀ
s 3%#52% /2$%2).'
s /2$%23 3()00%$ 7)4(). ꢃꢄ (/523
s %ꢂ-!), 2%30/.3% 7)4(). /.% (/52
ꢂ/2ꢂ
#ALL 4ODAY &OR !
&2%%
&ULL #OLOR #ATALOG
Download from Www.Somanuals.com. All Manuals Search And Download.
|