Model SMD-401
Smoke Dampers
APPLICATION
Model SMD-401 is a class I leakage rated smoke damper. High strength,
streamlined extruded airfoil blades insure lowest resistance to airflow in
HVAC systems with velocities to 3000 fpm (15.2 m/s) and 6 in. wg (1.5
kPa). Model SMD-401 may be installed vertically (with blades running
horizontal) or horizontally and is rated for airflow and leakage in either
direction.
Extruded Airfoil Blades
UL 555S Leakage Class I
Model SMD-401 meets the requirements for smoke
dampers established by:
National Fire Protection Association
RATINgS
NFPA Standards 92A, 92B, 101 & 105
Leakage:
UL 555S leakage class I. Leakage
rated in both directions
IBC International Building Codes
New York City (MEA listing #260-91-M)
California State Fire Marshall
Listing#: 3230-0981:108 (smoke)
Velocity:
Operational rated to 3000 fpm
(15.2 m/s) for sizes up to
48 in. W x 108 in. H or 144 in. H x 36 in. H
(1219mm x 2743mm) or
(3658mm x 914mm) or
2000 fpm (10.2 m/s) for sizes
greater than that. Rating is for
airflow in either direction through
damper.
250°F (121°C) with all actuators.
6 in. (1.5 kPa)
“UL CLASSIFIED (see complete marking on
product)”
Temperature:
Maximum Pressure:
“UL CLASSIFIED to Canadian safety standards
(see complete marking on product)”
Standard 555S (Listing #R13317)
STANDARD CONSTRUCTION
Frame:
5 in. x 1 in. (127mm x 25mm)
galvanized steel hat channel with
reinforced corners. A low profile
head and sill are used on sizes less
than 17 in. (432mm) high to
maximize free area and
performance.
Blades:
Seals:
Airfoil shape constructed of heavy
gauge extruded aluminum.
Structural reinforcement through
the entire length.
Extruded silicone rubber blade
seals. Flexible stainless steel jamb seals.
Concealed in jamb.
1⁄2 in. (13mm) dia. plated steel.
Bronze sleeve type
Linkage:
Axles:
Bearings:
SIzE LIMITATIONS:
Minimum Size:
Maximum Size:
Single Section:
8 in. W x 8 in. H (203mm x 203mm)
LH
H*
48 in. W x 60 in.
(1219mm W x 1524mm H)
192 in. W x 72 in. H
Multiple Section:
(4877mm W x 1829mm H) or
48 in. W x 288 in. H
W*
(1219mm W x 7315mm H) or
384 in. W x 36 in. H
(9754mm W x 914mm H)
RH
*W&H dimensions furnished approximately 1/4 in. (6mm) undersize.
(Add sleeve thickness for overall sleeved damper dimension)
Right hand drive is shown. Left hand drive is available upon request.
Optional Features:
• Galvanized steel sleeves
• Stainless steel bearings
• OCI (Open closed indication switches)
• Electric or pneumatic actuators to accomplish smoke
management and system functions.
• POC retaining angles
• Smoke detector
• Momentary switch
• Transformer
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Data
Damper Sideplate and Sleeve Dimensional Data
The drawings below illustrate the factory standard sideplate and sleeve mountings for the SMD-401. The standard "A" dimen-
sions listed in the table provide adequate space for the mounting of actuators and controls.
If space constraints are a problem the "A" dimension can be varied between 5 3⁄8 in. (136mm) and 12 in. (305mm).
Sleeve
Sideplate
1
1
/2" max.
"A" Dimension
Sleeve
in. (mm)
Sideplate
Standard
Maximum
12 (305)
All Dampers*
7 3/16 (183)
6 3/16 (157)
33/4"
When height is
11 in. (279) or
less with OCI
11 3/16
(284)
12
(305)
10 3/16
(259)
6 in.
Varies
53/8"
*With the exception of dampers 11 in. (279mm) high or less (12 in.
(305mm)high or less if width is greater than 64 in. (1625mm)) with OCI
option.
5 in.
A
5"
Sleeve Length
** On dampers 11 in. (279mm) high or less (12 in. (305mm)high or less if
width is greater than 64 in. (1625mm)) with OCI option, sideplate is 16 in.
(406mm)
A
12 in.**
T*
Space Envelopes Required for
Actuators and Accessories
S
Externally mounted actuators always require space
outside of the damper sideplate or sleeve. The “S” dimen-
sion illustrates the clearance required for various available
actuators.
On dampers less than 18 in. (457mm) high, actuators may
also require clearances above and/or below the sideplate
or sleeve. “B” and “T” dimensions are worst case clear-
ance requirements for some dampers less than 18 in.
(457mm) high. All damper sizes under 18 in. (457mm) high
do not require these worst case clearances. If space avail-
ability above or below the damper sleeve is limited, each
damper size should be individually evaluated.
B*
Actuator
Type/Model
B*
T*
S
With OCI
With OCI
120 Volt AC
5 1/4 in. (133mm) 3/4 in. (19mm)
ML4XXX Series Honeywell
MS4XXX Series Honeywell
MS4120 Series Honeywell
6 in. (152mm)
6 in. (152mm)
6 in. (152mm)
6 in. (152mm)
6 in. (152mm)
3/8 in. (10mm)
3/8 in. (10mm)
24 Volt AC
5 1/4 in. (133mm) 3/4 in. (19mm)
ML8XXX Series Honeywell
MS8XXX Series Honeywell
MS8120 Series Honeywell
6 in. (152mm)
6 in. (152mm)
6 in. (152mm)
6 in. (152mm)
6 in. (152mm)
3/8 in. (10mm)
3/8 in. (10mm)
Pneumatic (psi)
331-4551 Siemens
331-2976 Siemens
MK2-7121 Invensys
1 in. (25mm)
6 1/4 in. (159mm)
6 1/2 in. (165mm)
2 3/8 in. (60mm)
3 3/4 in. (95mm)
12 1/8 in. (308mm) 9 1/4 in. (235mm)
16 1/2 in. (419mm) 10 in. (254mm)
* For dampers 18 in. (457mm) or more in height these dimensions are 0 in. .
Download from Www.Somanuals.com. All Manuals Search And Download.
Damper Sizing Information
Dampers larger than maximum single section size are supplied as a factory
assembly of two or more sections of equal size.
The following figure shows the size damper section that has been qualified
for operation with a single actuator. Larger sizes can be accommodated using
multiples of these assembles.
ꢀꢁꢂJOꢃ
ꢄꢅꢄꢆNNꢇ
ꢈꢉꢂJOꢃ
ꢄꢊꢅꢀNNꢇ
Transitioned Damper When a fire/smoke damper is being used in conjunction with round or oval ductwork, the
SMD-401 can be supplied in a factory sleeve with round or oval transitions on both ends
of the sleeve. Dampers should be ordered to the duct dimensions. Drawings below show
overall damper size.
Dimensions
D*+
2 in. (51mm) +T
s
W*+ 2 in. (51mm)+T
s
W*+ 2 in. (51mm)+T
s
D*+ 2 in. (51mm)+T
s
H*+ 2 in. (51mm)+T
H*+ 2 in. (51mm)+T
s
s
H*
H*
21/8in.
21/8in.
(54mm)
21/8in.
(54mm)
(54mm)
*
W
W*
D*
16 in. (406mm)
Min.
16 in. (406mm)
Min.
16 in. (406mm)
Min.
TYPE R
TYPE O
TYPE C
These dimensions are furnished approximately 1/4 in. (6mm) undersize, except round and oval dimensions which are approximately 1/8 in. (3mm) undersize.
*
T
= (2)(Sleeve Thickness)
s
Specifications
Smoke Dampers meeting the following specifications
shall be furnished and installed where shown on plans
and/or as described in schedules. Dampers shall meet the
requirements of NFPA 92A, 92B, 101, & 105 and further shall
be tested, rated and labeled in accordance with the latest
edition of UL Standard 555S. Smoke dampers shall be of low
leakage design qualified to UL 555S Leakage Class I.
Damper blades shall be hollow extruded aluminum airfoil
type with structural reinforcing tube running full length of
each blade. Damper frame shall be galvanized steel formed
into a structural hat channel shape with reinforced corners.
Bearings shall be sintered bronze sleeve type rotating in
extruded holes in the damper frame. Blade edge seals shall
be silicone rubber designed to inflate and provide a tighter
seal against leakage as pressure on either side of the damper
increases. Jamb seals shall be stainless steel compression
type.
Each damper/actuator combination shall have a UL555S
elevated temperature rating of 250°F (121°C) minimum and
shall be rated to operate at maximum design airflow at its
installed location. Each damper shall be supplied with an
appropriate actuator installed by the damper manufacturer
at the time of damper fabrication. Damper actuator shall be
(specifier select one of the following) electric type for 120, 24,
or 240 Volt operation or pneumatic type for 25 psi minimum
(30 psi maximum operation.
Damper must be rated for mounting vertically (with blades
running horizontal) or horizontally and be UL 555S rated for
leakage and airflow in either direction through the damper.
The basis of design is Greenheck Model SMD-401.
Copyright ©2007 Greenheck Fan Corporation
SMD-401 Rev. 5 April 2007
Download from Www.Somanuals.com. All Manuals Search And Download.
|