Graco Yard Vacuum 253597 User Manual

Instructions - Parts List  
Carbon Steel  
1000cc Lower  
311717E  
ENG  
Designed for low to medium pressure, medium volume circulation of finishing materials.  
For professional use only.  
Not approved to European explosive atmosphere requirements.  
1180 psi (8.1 MPa, 81 bar) Maximum Working Pressure  
Important Safety Instructions  
Read all warnings and instructions in this manual and in  
your 1000cc Dura-Flo Pump manual 311833. Save all  
instructions.  
Model 253597, Series A  
UHMWPE/Leather Packings  
Model L10XCS, Series A  
UHMWPE/PTFE Packings  
Patent Pending  
TI8337a  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Warnings  
WARNING  
EQUIPMENT MISUSE HAZARD  
Misuse can cause death or serious injury.  
Do not operate the unit when fatigued or under the influence of drugs or alcohol.  
Do not exceed the maximum working pressure or temperature rating of the lowest rated system  
component. See Technical Data in all equipment manuals.  
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all  
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information  
about your material, request MSDS forms from distributor or retailer.  
Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-  
facturer’s replacement parts only.  
Do not alter or modify equipment.  
Use equipment only for its intended purpose. Call your distributor for information.  
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.  
Do not kink or over bend hoses or use hoses to pull equipment.  
Keep children and animals away from work area.  
Comply with all applicable safety regulations.  
MOVING PARTS HAZARD  
Moving parts can pinch or amputate fingers and other body parts.  
Keep clear of moving parts.  
Do not operate equipment with protective guards or covers removed.  
Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,  
follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.  
TOXIC FLUID OR FUMES HAZARD  
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or  
swallowed.  
Read MSDS’s to know the specific hazards of the fluids you are using.  
Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.  
Always wear impervious gloves when spraying or cleaning equipment.  
PERSONAL PROTECTIVE EQUIPMENT  
You must wear appropriate protective equipment when operating, servicing, or when in the operating  
area of the equipment to help protect you from serious injury, including eye injury, inhalation of toxic  
fumes, burns, and hearing loss. This equipment includes but is not limited to:  
Protective eyewear  
Clothing and respirator as recommended by the fluid and solvent manufacturer  
Gloves  
Hearing protection  
SKIN INJECTION HAZARD  
High-pressure fluid from dispense valve, hose leaks, or ruptured components will pierce skin. This may  
look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical  
treatment.  
Do not point dispense valve at anyone or at any part of the body.  
Do not put your hand over the end of the dispense nozzle.  
Do not stop or deflect leaks with your hand, body, glove, or rag.  
Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,  
checking, or servicing equipment.  
311717E  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operation  
Operation  
6. Open all fluid drain valves in the system, having a  
waste container ready to catch drainage. Leave  
drain valve(s) open until you are ready to spray  
again.  
Pressure Relief Procedure  
7. If you suspect the spray tip or hose is clogged or  
that pressure has not been fully relieved after follow-  
ing the steps above, VERY SLOWLY loosen tip  
guard retaining nut or hose end coupling to relieve  
pressure gradually, then loosen completely. Clear  
hose or tip obstruction.  
1. Engage trigger lock.  
2. Air-Powered Pumps only: Close the bleed-type  
master air valve.  
Hydraulic-Powered Pumps only: Close the hydraulic  
supply line valve first, then the return line valve.  
CAUTION  
Hydraulic-Powered Pumps only: When shutting down  
the hydraulic system, always shut off the hydraulic  
supply line shutoff valve first, and then the return line  
shutoff valve to prevent overpressurizing the motor or  
its seals. When starting the hydraulic system, open  
the return line shutoff valve first.  
3. Disengage the trigger lock.  
4. Hold a metal part of the gun firmly to a grounded  
metal pail. Trigger the gun to relieve pressure.  
5. Engage the trigger lock.  
4
311717E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Repair  
Repair  
Piston  
To service the pump assembly, see manual  
311833.  
1. Remove the intake valve as explained above.  
2. Pull the cylinder (24) down, off the piston assembly.  
To service the air motor, see manual 311238.  
3. Unscrew the piston retainer screws (12). Remove  
the piston parts from the displacement rod (22).  
Disconnect the Lower  
4. Clean all parts thoroughly, and inspect them for  
wear or damage. Replace parts as needed.  
5. Place the gasket (49) and ball (3) on the piston  
retainer (27). Install these parts in the displacement  
rod.  
1. Flush the pump, if possible. Relieve the pressure,  
see Pressure Relief Procedure on page 4.  
2. Disconnect the hoses from the lower and plug the  
ends to prevent fluid contamination.  
The piston retainer (27) must not obstruct the ports  
in the displacement rod (22).  
3. Remove the pump from its mounting and place it in  
a vise.  
6. Install one cup packing (17) on the displacement rod  
(22). Be sure the lips of the packing face up.  
4. Disconnect the lower from the motor as explained in  
your separate pump manual.  
7. Install the packing spacer (16). Position one cup  
packing (17) on the displacement rod so the lips of  
the packing face down.  
Lower Repair  
8. Install the piston guide (21). Install the four screws  
(12) through the piston assembly and screw them  
into the displacement rod (22). Torque the screws  
evenly to 30-40 ft-lb (41-54 N•m), using a  
criss-cross tightening pattern.  
Intake Valve  
1. Remove the hex nuts (1) and washers (30) from the  
tie rods (18). Unscrew the tie rods from the intake  
valve. Remove the intake valve from the pump.  
9. If no further service is need, go to Throat Packings.  
If no further service is needed, slide the cylinder  
(24) and gaskets (49*) over the piston assembly.  
Install the intake valve. Torque the nuts (1) evenly to  
50-60 ft-lb (68-81 N•m).  
2. Disassemble the intake valve. Take note of which  
set of holes the ball stop pin (14) is in.  
3. Clean all parts thoroughly, and inspect them for  
wear or damage. Replace parts as needed.  
Throat Packings  
4. Reassemble the valve. Place the ball stop pin (14) in  
the same holes from which it was removed. If you  
want to change the fluid flow through the pump,  
place the pin in a different set of holes. Refer to  
Check Valve Adjustment, page 6.  
1. Remove the intake valve and the cylinder (24) as  
explained in the previous sections.  
2. Remove the wet cup (45).  
3. Pull the displacement rod (22) out of the bottom of  
the outlet housing (46).  
5. If no further service is needed, reinstall the intake  
valve on the pump. Torque the hex nuts (1) evenly to  
50-60 ft-lb (68-81 N•m), using a criss-cross tighten-  
ing pattern.  
4. Remove the throat packings and glands from the  
outlet housing (46).  
5. Clean all parts thoroughly, and inspect them for  
wear or damage. Replace parts as needed.  
311717E  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
     
Repair  
Reconnect the Lower  
Always replace the male gland (40) and the bearing  
(47) when the throat packings are replaced.  
1. Reinstall the displacement pump on the motor as  
explained in your pump manual.  
6. Install the throat packings into the outlet housing  
(46) one at a time in the following order, with the lips  
of the v-packings facing down:  
2. Reconnect the ground wire to the motor.  
Check Valve Adjustment  
The fluid piston and intake valves are factory-set for  
high-volume pumping of heavy, spray-viscosity fluids.  
The male gland (40*), two UHMWPE v-packings  
(41*), one leather v-packing (42*), one UHMWPE  
v-packing, one leather v-packing (42*), one UHM-  
WPE v-packing, and the bearing (41). Loosely  
install the wet cup (45).  
For lighter fluids or lower volume requirements, or to  
reduce surging at the stroke change-over, decrease the  
travel of the balls (3 and 4). Move the pins (2) to a lower  
set of holes. See Parts, page 8 and refer to disassembly  
procedure above.  
7. Push the displacement rod (22) up into the outlet  
housing (46) until it protrudes from the wet cup (45).  
Continue reassembling the pump in the reverse  
order of disassembly. Tighten the wet cup just tight  
enough to prevent leakage.  
If the ball travel is too short for the fluid being  
pumped, the fluid flow will be restricted.  
For heavier fluids or to increase the flow, increase the  
travel of the balls (3 and 4). See Parts, page 8 and refer  
to disassembly procedure above.  
6
311717E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Repair  
6
51  
1
30  
47  
3
5
1
1
41  
42  
41  
42  
41  
40  
7
46  
18  
22  
11  
24  
14  
3
2
49  
17  
27  
16  
14  
2
12  
4
2
4
1
2
3
4
5
6
7
Apply anti-seize lubricant to all packings.  
Torque to 30-40 ft-lb (22-30 N•m).  
Torque to 50-60 ft-lb (37-44N•m).  
Apply thread sealant.  
48  
11  
TI8390a  
Apply medium strength threadlocker.  
Torque 75-80 ft-lb (55-59 N•m).  
Lips of v-packings must face down.  
FIG. 1  
311717E  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts  
Parts  
3
49  
27  
51  
6
5
17*  
16  
45  
17*  
21  
47  
1
7
42*  
1
7
1 41*  
4
2
12  
1 3  
30  
11*  
40*  
7
1
34  
35  
24  
18  
46  
14  
11*  
4
22  
49  
48  
2*  
TI8335a1  
1
2
3
Apply anti-seize lubricant to all packings.  
Torque to 30-40 ft-lb.  
Torque to 50-60 ft-lb.  
4
Apply thread sealant.  
5
6
7
Apply medium strength threadlocker.  
Torque 75-80 ft-lb.  
Lips of v-packings must face down.  
8
311717E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Parts  
Model 253597 and L10XCS, Carbon Steel  
Lowers  
Repair Kit 223439, for Model 253597  
Qt  
y.  
Part  
Description  
Qt  
y
Ref. Part  
Description  
100103  
100579  
111334  
188846  
104260  
108845  
104263  
PIN, cotter; 1.5 in. (38 mm long)  
PIN, cotter; 1 in (25.4 mm) long  
O-RING; PTFE  
1
4
2
2
1
4
2
1
100127 NUT; mscr, hex  
100579 PIN; cotter  
4
4
1
1
2
4
2
1
2
4
1
1
1
1
1
4
2
1
1
4
2*  
3
101178 BALL; metallic  
101718 BALL; steel  
PACKING, cup; UHMWPE  
GLAND, male  
4
11*  
12  
14  
16  
17*  
18  
21  
22  
24  
27  
111334 O-RING, PTFE  
104272 SCREW; cap; sch  
161599 PIN; ball stop  
V-PACKING; UHMWPE  
V-PACKING; leather  
Repair Kit 224443, for Model L10XCS  
166597 SPACER; packing  
188846 PACKING; cup, UHMWPE  
171692 ROD; tie  
Qt  
y.  
Part  
Description  
171696 GUIDE; piston  
178508 ROD; displacement  
181269 CYLINDER; motor; hydr  
223438 RETAINER; piston  
100103  
100579  
111334  
188846  
104260  
108845  
111327  
186056  
PIN, cotter; 1.5 in. (38 mm long)  
PIN, cotter; 1 in (25.4 mm) long  
O-RING; PTFE  
1
4
2
2
1
4
2
1
PACKING, cup; UHMWPE  
GLAND, male  
28172479 TAG; warning  
30  
100128 WASHER; lock  
V-PACKING; UHMWPE  
V-PACKING; PTFE  
34  
100055 SCREW; drive; #6  
178509 PLUG; disp. rod  
38  
BEARING, PEEK  
40*  
41*  
104260 GLAND; pkg; male  
108845 PACKING; vee, UHMWPE  
PACKING; vee; leather; used on Model  
253597  
42*  
104263  
111327  
2
PACKING, vee; PTFE; used on Model  
L10XCS  
45  
46  
47  
48  
49  
51  
186054 CUP; wet  
1
1
1
1
1
1
15J780 HOUSING; outlet; pump  
186056 BEARING, PEEK  
223437 HOUSING; valve; intake  
110728 GASKET  
15H773 ADAPTER  
*
Included in Repair Kit 223439 (for Model 253597) or  
Repair Kit 224443 (for Model L10XCS).  
** Recommended spare parts. Keep these spare parts on  
hand to reduce down-time.  
Replacement Danger and Warning labels, tags, and cards  
are available at no cost.  
311717E  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Outlet Housing Mounting Hole Layout  
Outlet Housing Mounting Hole Layout  
3.464 in. (88 mm)  
3.464 in. (88 mm)  
2 in. (51 mm)  
4 in. (102 mm)  
2 in. (51 mm)  
4 in. (102 mm)  
TI11492a  
10  
311717E  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Dimensions  
Dimensions  
A
Weight  
(approx)  
lb (kg)  
(Height)  
in. (mm)  
B
(Inlet)  
C
(Outlet)  
22.1 (561)  
2 in. npt(f)  
1-1/2 in. npt(f) 50 (22.5)  
A
C
TI8337a  
B
Technical Data  
Maximum Fluid Working Pressure . . . . . . . . . . . . . . . . . . 1180 psi (8.1 MPa, 81 bar)  
Wetted parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303 Grade Stainless Steel, Carbon Steel, Chrome Steel,  
Chrome, Zinc, and electroless Nickel Plating, Buna-N,  
Tungsten Carbide, Nylon, Ultra-High Molecular Weight  
Polyethylene, Leather, PTFE, Polyetheretherketone  
(PEEK)  
311717E  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Graco Standard Warranty  
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in  
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty  
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by  
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with  
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or  
maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of  
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned  
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will  
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED  
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.  
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to  
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these  
warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or  
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,  
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la  
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite  
de ou en rapport, directement ou indirectement, avec les procédures concernées.  
Graco Information  
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.  
Phone: 612-623-6921 or Toll Free: 1-800-328-0211 Fax: 612-378-3505  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
Original instructions. This manual contains English. MM 311717  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441  
Copyright 2006, Graco Inc. is registered to ISO 9001  
Revised 03/2011  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   

Haier Water Heater QBJ1 130A58E User Manual
Harbor Freight Tools Laser Level 90980 User Manual
Honeywell Smoke Alarm ANN RLY User Manual
HP Hewlett Packard Computer Accessories 86720A User Manual
HP Hewlett Packard Computer Monitor 705 User Manual
Humminbird Fish Finder 717 User Manual
Humminbird Fish Finder 531338 1_C User Manual
Hunter Fan Fan 22438 User Manual
Husqvarna Lawn Mower 155 User Manual
Ikelite Digital Camera F60fd User Manual