Instructions–Parts List
307043ZAA
ENG
Monarkr Air Motor
For use with Graco fluid handling pumps.
180 psi (1.2 MPa, 12 bar) Maximum Air Working Pressure
Model 206955, Series K
For STANCHION TUBE mounting
Model 205997, Series K
Model 215363, Series D
Model 222791, Series D
For 3 tie rod mounting
Model 207546, Series H
For hinged clamp mounting
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
See page 2 for Table of Contents.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
SKIN INJECTION HAZARD
Spray from the gun/dispensing valve, leaks or ruptured components can inject fluid into your body and
cause extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the
skin can also cause serious injury.
D Fluid injected into the skin might look like just a cut, but it is a serious injury. Get immediate
surgical treatment.
D Do not point the gun/valve at anyone or at any part of the body.
D Do not put your hand or fingers over the spray tip/nozzle.
D Do not stop or deflect leaks with your hand, body, glove or rag.
D Do not “blow back” fluid; this is not an air spray system.
D Always have the tip guard and the trigger guard on the gun/valve when spraying.
D Check the gun diffuser operation weekly. Refer to the gun manual.
D Be sure the gun trigger safety operates before spraying.
D Lock the gun trigger safety when you stop spraying.
D Follow the Pressure Relief Procedure on page 6 if the spray tip/nozzle clogs and before clean-
ing, checking or servicing the equipment.
D Tighten all fluid connections before operating the equipment.
D Check the hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
Do not repair high pressure couplings; you must replace the entire hose.
D Use only Graco approved hoses. Do not remove the spring guard that is used to help protect the
hose from rupture caused by kinks or bends near the couplings.
MOVING PARTS HAZARD
Moving parts, such as the air motor piston, can pinch or amputate your fingers.
D Keep clear of all moving parts when starting or operating the pump.
D Before servicing the equipment, follow the Pressure Relief Procedure on page 6 to prevent the
equipment from starting unexpectedly.
3
307043
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
D Ground the equipment and the object being sprayed. Refer to Grounding on page 5.
D If there is any static sparking or you feel an electric shock while using this equipment, stop spray-
ing/dispensing immediately. Do not use the equipment until you identify and correct the problem.
D Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid
being sprayed/dispensed.
D Keep the spray/dispense area free of debris, including solvent, rags, and gasoline.
D Electrically disconnect all equipment in the spray/dispense area.
D Extinguish all open flames or pilot lights in the spray/dispense area.
D Do not smoke in the spray/dispense area.
D Do not turn on or off any light switch in the spray/dispense area while operating or if fumes are
present.
D Do not operate a gasoline engine in the spray/dispense area.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D Know the specific hazards of the fluid you are using.
D Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state and national guidelines.
D Always wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and
solvent manufacturer.
4
307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
5. To maintain grounding continuity when flushing or
Grounding
relieving pressure, always hold a metal part of the
gun/valve firmly to the side of a grounded metal
pail, then trigger the gun/valve.
WARNING
FIRE AND EXPLOSION HAZARD
Before operating the pump, ground the
system as explained below. Also read
the section FIRE AND EXPLOSION
HAZARD on page 4.
To ground the pump:
To ground the pump, loosen the grounding lug locknut
(W) and washer (X). Insert one end of a 12 ga (1.5
mm@) minimum ground wire (Y) into the slot in lug (Z)
and tighten the locknut securely. Connect the other
end of the wire to a true earth ground. Order 222011,
Ground Wire and Clamp.
Proper grounding is an essential part of maintaining a
safe system.
Z
To reduce the risk of static sparking, ground the pump.
Check your local electrical code for detailed grounding
instructions for your area and type of equipment. Be
sure to ground all of this equipment:
Y
1. Pump: use a ground wire and clamp as shown in
Fig. 1.
X
2. Air and fluid hoses: use only electrically conductive
W
hoses.
3. Air compressor: follow manufacturer’s recommen-
dations.
04111
Fig. 1
4. Fluid supply container: according to local code.
5
307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor Service
Pressure Relief Procedure
Disassembly
1. Flush the pump.
WARNING
SKIN INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure above.
starting or spraying/dispensing acciden-
tally. Fluid under high pressure can be injected
through the skin and cause serious injury. To re-
duce the risk of an injury from injection, splashing
fluid, or moving parts, follow the Pressure Relief
Procedure whenever you:
2. Relieve the pressure.
D are instructed to relieve the pressure,
D stop spraying/dispensing,
D check or service any of the system equipment,
D or install or clean the spray tip/nozzle.
3. Remove the pump according to the instructions in
the pump manual.
4. Place the air motor base (F) in a vise with the air
motor up.
1. Close the pump air regulator and the bleed-type
master air valve (required in your system).
5. Loosen the cap nut (B). Pull up the cap nut, grip
the trip rod (C) with the padded pliers, and screw
the cap nut off of the rod.
2. Hold a metal part of the spray gun/dispensing
valve firmly to a grounded metal waste container
and trigger the gun/valve to relieve the fluid pres-
sure.
CAUTION
Before You Start
Do not damage the plated surface of the trip rod (C).
Damaging the surface of the trip rod can result in
erratic air motor operation. Use the special padded
pliers 207579 to grasp the rod.
D Be sure you have all necessary parts on hand.
Air Motor Repair Kit 206728 includes repair parts
for the motor. Use all the parts in the kit for the best
results. Parts included in the kit are marked with an
asterisk, for example (19*), in the text and dra-
wings. See Parts List on pages 10 – 14.
6. Remove the six screws (D) holding the cylinder (E)
to the base (F). Carefully pull the cylinder straight
up off of the piston assembly (G).
D For best results keep parts marked with one aster-
isk on hand to reduce down time.
D Two accessory tools should be used: Padded
Pliers, 207579, are used to grip the trip rod without
damaging its surface, and a 0.145-in. (3.7 mm)
Gauge, 171818, is used to assure the proper
clearance between the poppets and the piston.
CAUTION
To avoid damaging the cylinder wall, lift the cylinder
straight up off of the piston. Never tilt the cylinder as
it is being removed.
6
307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor Service
7. Pull the piston assembly (G) from the air motor
11. Use a screwdriver to push down on the trip rod
yoke (O), and snap the toggles down. See Fig. 3.
base (F), and set it aside.
8. Remove the bearing housing assembly (26 or 27)
for all Models except Model 206955. Remove and
wipe the seat clean with a cloth. For model
206955, remove retainer ring (3) and bearing (4).
Remove seal (2, 27 or 28).
WARNING
MOVING PARTS HAZARD
To reduce the risk of pinching or ampu-
tating your fingers, keep your fingers
clear of the toggle assemblies when you
are snapping the toggles (U in Fig. 3 ) up
or down.
9. Remove the base from the vise, and set it upright
on the workbench.
10. Place the piston rod flats in a vise.
B
12. In this step, while you are prying with the screw-
driver with one hand, cover the toggle assemblies
with your other hand so as to catch the spring-
loaded toggle assemblies when they snap out of
the lugs. Place the tip of a screwdriver into the
piston between the piston lugs (P) below the pivot
pins (Q) on the toggles, pry up with the screw-
driver handle to compress the springs on the
toggle assembly (U) up and away from the piston
lugs, and remove the parts. See Fig. 3.
C
E
G
D
F
A
05703
Fig. 2
7
307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor Service
13. Straighten the lockwires (L*) and remove them
Reassembly
from the upper valve nuts (J*). Screw the upper
valve nuts off. Remove the trip rod yoke (O),
actuator (V), and trip rod (C).
1. Place the piston rod (A) flats in the vise with the air
motor up.
2. Pull the exhaust valve poppets (M*) into the valve
actuator (V), and clip off the top parts of the pop-
pets (shown with dotted lines in the Cutaway View
in Fig. 3).
14. Unscrew the bottom valve nuts (K*), and remove
the poppets (N*). Make sure the valve bar spring
clips (W) are not worn or damaged and that they
properly guide the actuator (V).
3. Install the grommets (Y*) in the actuator (V), place
the inlet valve poppets (N*) in the piston, and
thread the bottom valve nuts (K*) onto the inlet
valve poppets until there are a few threads left
before the threads run out.
15. Remove the exhaust valve poppets (M) by cutting
them with a side cutter, then pull them out of the
actuator (V).
NOTE: If you thread the valve nuts too far down onto
the poppets, they will run off of the threaded part of the
poppets.
16. Remove piston o-ring (Z) and internal base o-ring
(15* or 19*). Inspect o-rings.
4. Place the actuator (V) in the yoke (O) and insert
the trip rod (C) through them. Thread a 5/16–18
unc nut on the trip rod to prevent it from sliding into
the piston when assembling. Grease the trip
rod/actuator/yoke assembly heavily and place into
the piston with the inlet valve poppets (N*) going
through the grommets (Y*).
17. Clean all the parts carefully in a compatible solvent
and inspect them for wear or damage. Use all the
repair kit parts during reassembly, and replace
other parts as necessary.
18. Check the surfaces of the piston, piston rod, and
cylinder wall for scratches or wear. A scored rod
will cause premature packing wear and leaking.
5. Thread the top valve nuts (J*) onto the inlet valve
poppets (N*) until one thread of the inlet valve
poppets is exposed above the valve nuts.
Cut off the tops of the poppets
as indicated by the dotted lines
Z
T
R
C O U
L
T
U
S
Q
J
V
W
M
X
X
Insert Screw
Driver Here
J
Y
K
P
Z
G
F
0.145 in.
(3.7 mm)
G
N
04118
04119
Cutaway View
Fig. 3
8
307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Air Motor Service
6. Install the toggle pins (Z) in the yoke (O). As-
13. Grease and install the bearing housing assembly
(26 or 27) for all Models except Model 206955, or
seal (2*), ring retainer (3) and bearing (4) for
Model 206955 into the air motor base (F).
semble the toggle assembly (U) by placing a well
greased spring onto the toggle arm (T) and then
the toggle rocker (S). Place the toggle arm (T)
ends of the toggle assembly (U) onto the toggle
pins, and snap the pivot pin (S) ends of the toggle
assembly into the lugs (P).
14. Slide the piston rod (A) down through the bearing
housing assembly, and lower the piston assembly
(G) into the air motor base (F).
7. Set gap on inlet valve (N) using the .145 in. (3.68
mm) side of gauge 171818. Rotate valve stem (X*)
until snug against gauge, then back off until valve
stem slot is lined up with wire holes in valve nut
(J*) (do not back off more than 1/2 turn). See the
Cutaway View Fig. 3.
15. Carefully lower the cylinder (E) straight down onto
the piston assembly (G). Tighten the six screws
(D) holding the cylinder to the base (F).
CAUTION
To avoid damaging the cylinder wall, lower the cylin-
der straight down onto the piston. Never tilt the
cylinder as it is being lowered.
8. Tighten the bottom valve nuts (K*) securely by
hand.
9. Align the holes in the valve nuts (K*) and the slots
on the tops of the inlet valve poppets (N*), and
drop the lock wires (L*) through the holes in the
valve nuts and into the slots in the inlet valve
poppets. Pull the lock wires down tightly, and bend
the ends about 120_ with needle-pliers so that they
cannot be pulled back out of the holes.
16. Grip the trip rod (C) with padded pliers. Remove
the 5/16 nut from the top of the trip rod. Screw the
cap nut (B) onto the trip rod (C), push the cap nut
down, and screw it into the top of the cylinder (E).
WARNING
MOVING PARTS HAZARD
CAUTION
Never re-use the old lock wires. They will get brittle
and break easily from too much bending.
Never operate the air motor with the air
motor identification plates removed. The
piston and associated parts can ampu-
tate a hand or finger caught between
them.
Do not score the lock wires when you bend them
because they will break on the scoring.
10. Grease and install the new o-rings on the piston
assembly (G) and in the groove in the air motor
base (F).
17. Replace the identification plates (19, 23 or 26)
before operating the air motor.
11. Clamp the air motor base (F) in a vise by closing
the vise jaws on the flange.
18. Before remounting the the air motor to the pump,
connect an air hose and run the air motor slowly,
starting with just enough air pressure to make the
air motor run, and make sure that it operates
smoothly.
12. Grease and install the seal (2, 27 or 28) into the air
motor base (F). Install bearing (4) and ring retainer
(3) into the base for Model 206955. Grease and
install the bearing housing assembly (26 or 27) for
all other models.
19. Reconnect the ground wire before regular opera-
tion.
9
307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
HINGED CLAMP MOUNTING: SANITARY
Model 207546, Series H, Air Motor Assembly
Includes items 1–36
20
n3
21
4
11
5
13
10*
9*
n7
6
24*
8*
32
9*
n31
33
34
25
*12
17
23*
18
28
29
26
n27
*15
NOTE:
Seal lips face upward
n14
30
2
19Y
36
35
22
1
05704
10 307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
HINGED CLAMP MOUNTING: SANITARY
Model 207546, Series H, Air Motor Assembly
Includes items 1–36
Ref.
No.
Ref.
No.
Part No. Description
Qty.
Part No. Description
Qty.
1
114422
101578
SCREW , phillips hd mach;
no. 8–32 x 0.375 in. (10 mm) long. 8
SCREW, hex head;
5/16 x 0.875 in. (10 mm) long
O-RING; buna-N
YOKE, rod, trip
PIN, toggle
ROCKER, toggle
SPRING, helical compression
GROMMET, rubber, air intake
NUT, adjusting
LOCKWIRE, transfer valve
ACTUATOR, valve
O-RING, nitrile rubber
ARM, toggle
O-RING, buna-N
O-RING, buna-N
GASKET; copper
ROD; piston
PLATE, warning (English)
NUT, cap
CYLINDER
PLATE, identification
POPPET, valve; urethane
POPPET, valve; urethane
ROD, trip
BEARING HOUSING Assy;
Includes items 27–29
S SEAL
28
29
101526
S BEARING
1
S HOUSING, bearing
(not sold separately)
BASE
PISTON Assy;
Includes items 32–34 (also includes
2
1
1
6
1
1
2
2
2
2
4
2
1
1
2
1
1
1
1
1
1
1
1
2
2
1
30
239113
3n
4
5
6
7n
8*
156698
158360
158362
158364
167585
158367
160261
160618
172867
160621
160623
31n 214036
repair kit 206728 when ordered as
a replacement part)
S SCREW, rd hd mach;
no. 6–32 x 0.25” (6.3 mm)
S CLIP, spring
S PISTON, bare
(not sold separately)
1
32
102975
172866
2
2
9*
33
34
10*
11
12*
13
1
1
1
35
36
104029
104582
LUG, grounding
WASHER, tab
14n 160624
15* 160625
17n 160932
18 177136
19Y 172573
n Keep these spare parts on hand to reduce down
time.
*
These parts are included in Repair Kit 206728,
which may be purchased separately. See page 16.
20
169627
169628
172572
236079
170709
203965
207547
21
22
23*
24*
25
26
Y If you have operators who do not read English, or-
der one of the following labels from your Graco dis-
tributor. Paste the label over the English warning
plate (19).
290460
290461
290462
FRENCH
GERMAN
SPANISH
1
1
27n 16H224
11
307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
STANCHION TUBE MOUNTING
Model 206955, Series K,
Air Motor Assembly
25
Includes items 1–37
n7
24
8
15
9
17
14*
13*
n11
10
28*
12*
31
13*
29
n30
32
33
*16
23
27*
21
3
4
n2
NOTE:
Seal lips face upward
*19
n18
20
5
26
36
Y37
35
34
6
1
05705B
12 307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
STANCHION TUBE MOUNTING
Model 206955, Series K, Air Motor Assembly
Includes items 1–37
Ref.
No.
Ref.
No.
Part No. Description
Qty.
Part No. Description
Qty.
1
114422
SCREW, phillips hd mach;
no. 8–32 x 0.38 in. (10 mm) long. 16
28*
29
170709
203965
POPPET, valve; urethane
ROD, trip
2
1
2n
3
4
16H224
101525
101526
101578
SEAL
RING, retainer
BEARING
SCREW, hex head;
5/16 x 0.875 in. (10 mm) long
UNION, straight adapter;
3/8 npt(mxf)
O-RING; buna-N
YOKE, rod, trip
1
1
1
30n 214036
PISTON Assy; Includes items
31–33 (also includes
repair kit 206728 when
ordered as a replacement part)
S SCREW, rd hd mach;
no. 6–32 x 0.25” (6.3 mm)
S CLIP, spring
S PISTON, bare
(not sold separately)
LUG, grounding
WASHER, tab
5
1
6
31
102975
172866
6
155665
2
2
1
1
1
2
2
2
2
4
2
1
1
2
1
1
1
1
1
1
1
1
2
32
33
7n
8
9
156698
158360
158362
158364
1
1
1
1
1
PIN, toggle
34
35
36
104029
104582
180233
10
ROCKER, toggle
SPRING, helical compression
GROMMET, rubber, air intake
NUT, adjusting
LOCKWIRE, transfer valve
ACTUATOR, valve
O-RING; nitrile rubber
ARM, toggle
O-RING, buna-N
O-RING, buna-N
BASE
ROD; piston
GASKET; copper
CYLINDER
11n 167585
LABEL, warning
PLATE, warning (English)
12*
13*
14*
15
16*
17
158367
160261
160618
172867
160621
160623
37Y 241650
n Keep these spare parts on hand to reduce down
time.
*
These parts are included in Repair Kit 206728,
which may be purchased separately. See page 16.
18n 160624
19*
20
21
160625
160885
160886
Y If you have operators who do not read English, or-
der one of the following labels from your Graco dis-
tributor. Paste the label over the English warning
plate (37).
23n 160932
24
25
26
27*
164186
164704
241651
236079
NUT, cap; with carry handle
PLATE, identification
POPPET, valve; urethane
290460
290461
290462
FRENCH
GERMAN
SPANISH
13
307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 205997, Series K
Air Motor Assembly
Includes: 1, 3–19, 23, 25–34, 36–43
21
36
Model 215363, Series D
Air Motor Assembly
Includes: 1, 3–19, 21, 23, 25–34, 37–43
n4
46,18
5
Model 222791, Series D
Air Motor Assembly
Includes: 1–23, 25–34, 39–43
11
6
13
10*
9*
n19
n7
25*
8*
32
9*
n31
33
34
26
*12
17
24*
22, 37
29
30
27
n28
*15
NOTE:
Seal lips face upward
n14
20, 38, 44
23
2
3
40
39
Y43
1
05706B
14 307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 205997, Series K Air Motor Assembly
Includes: 1, 3–19, 23, 25–34, 36–43
Model 215363, Series D Air Motor Assembly
Includes: 1, 3–19, 21, 23, 25–34, 37–43
Model 222791, Series D Air Motor Assembly
Includes: 1–23, 25–34, 39–43
Ref.
No.
Ref.
No.
Part No. Description
Qty.
Part No. Description
PISTON Assy;
Qty.
1
114422
SCREW, phillips hd mach;
31n 214036
no. 8–32 x 0.375 in. (10 mm)
Includes items 32–34 (also includes
long
16
1
repair kit 206728 when ordered
2
3
100361
101578
PLUG, pipe; 1/2 in. npt
SCREW, hex head;
5/16 x 0.875 in. (10 mm) long
O-RING; buna-N
YOKE, rod, trip
as a replacement part)
S SCREW, rd hd mach;
no. 6–32 x 0.25” (6.3 mm)
S CLIP, spring
S PISTON, bare
(not sold separately)
NUT, cap
ROD, piston
BASE
LUG, grounding
WASHER, tab
1
32
102975
172866
6
1
1
2
2
2
4
2
1
1
2
1
1
1
1
2
1
1
1
1
2
2
1
2
2
4n
5
6
7n
8*
9*
10*
11
12*
13
156698
158360
158362
158364
158367
160261
160618
172867
160621
160623
33
34
PIN, toggle
1
1
1
1
1
1
1
1
1
1
ROCKER, toggle
GROMMET, rubber, air intake
NUT, adjusting
LOCKWIRE, transfer valve
ACTUATOR, valve
O-RING, nitrile rubber
ARM, toggle
O-RING, buna-N
O-RING, buna-N
GASKET; copper
CYLINDER
SPRING, helical compression
BASE
NUT, cap; with carry handle
ROD; piston
PLATE, identification
POPPET, valve; urethane
POPPET, valve; urethane
ROD, trip
36
37
38
39
40
42
161435
177136
205998
104029
104582
180233
LABEL, warning
PLATE, warning (English)
BASE
43Y 241650
44
46
14n 160624
15* 160625
17n 160932
18 164186
19n 167585
609354
609353
CYLINDER
n Keep these spare parts on hand to reduce down
time.
20
21
22
23
24*
25*
26
27
184270
164704
164705
241651
236079
170709
203965
205529
*
These parts are included in Repair Kit 206728,
which may be purchased separately. See page 16.
Y If you have operators who do not read English, or-
der one of the following labels from your Graco dis-
tributor. Paste the label over the English warning
plate (43).
BEARING HOUSING;
Includes 28–30
S SEAL
S BEARING
S NUT, packing
1
1
1
1
28n 16H224
290460
290461
290462
FRENCH
GERMAN
SPANISH
29
30
101526
164701
15
307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
BLEED-TYPE MASTER AIR VALVE (REQUIRED)
GROUNDING WIRE 222011
25 ft (7.6 m) long, 12 awg
For grounding pump
300 psi (21 bar, 2.1 MPa) Maximum Working Pressure
Relieves air trapped in the air line between the pump
air inlet and this valve when closed.
107141 3/4 npt (m x f) inlet and outlet
107142 1/2 npt (m x f) inlet and outlet
GAUGE 171818
For adjusting the air transfer valves.
TRIP ROD PLIERS 207579
Special padded pliers for gripping the air motor trip rod.
AIR MOTOR REPAIR KIT 206728
Contains replacements parts noted in the Parts.
SILENCER KIT 215354
Fits Monark Air Motors Models 206955, 222991,
MONARK MUFFLER CONVERSION KIT 241953
205997 and 215363. See Instruction Manual 307361.
Converts Monark motors to new style muffler plates.
16 307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensional
Drawings
Mounting Hole
Layouts
3 Tie Rod Pumps
4.38 in. (111.3 mm)
diameter
13.25 in.
(336.6 mm)
2.5 in. (64 mm)
5 in. (127 mm)
0.28 in. (7.1 mm)
diameter
05707
11.75 in.
(298.4 mm)
15.75 in.
(400.1 mm)
for 206955
5.75 in.
(146.1 mm)
2 Stanchion Tube Pumps
161322
gasket
Three 0.34 in. (8.6 mm)
diameter holes
on 6.38 in. (162.1 mm) bolt
circle
05709
45_
1 in. (25 mm)
radius
45_
2.5 in. (64 mm)
4 in. (102 mm)
2.5 in.
(64 mm)
05708
Technical Data
Maximum Working Pressure
Air Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Urethane
Valve mechanism . . . . . . . . . . . . . . Balanced; detented
Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nitrile rubber
Approximate weight . . . . . . . . . . . . . . . . . . 13 lb (5.9 Kg)
. . . . . . . . . . . . . . . . . . . . . . . . . . 180 psi (12 bar, 1.2 MPa)
2
2
Effective piston area . . . . . . . . . . . . . . . . 7 in. (45 cm )
Effective piston diameter . . . . . . . . . . . . . 3 in. (76 mm)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 in. (76 mm)
Sound Data*
Sound Level . . . . . . at 180 psi, 25 cycles/min: 96 dBa
Sound Power . . . . at 180 psi, 25 cycles/min: 112 dBa
* Tested in accordance with ISO 3744.
17
307043
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from
defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended,
or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the
equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained
in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor, or call one of the following numbers
to identify the distributor closest to you:
1–800–328–0211 Toll Free 612–623–6921 612–378–3505 Fax
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 307043
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
Copyright 1970, Graco Inc. is registered to ISO 9001
Revised 3/2011
18 307043
Download from Www.Somanuals.com. All Manuals Search And Download.
|