Graco Inc Power Roller 244279 User Manual

INSTRUCTIONS–PARTS LIST  
Important Safety Instructions  
309323E  
D
Read all warnings and instructions  
in this manual. Save these  
instructions.  
Pressure Roller with 20”  
Fixed Extension  
Model 244279, Series C  
D 20 in. (50 cm) heavy-duty extension  
D 9 in. (23 cm) roller frame  
D 1/2 in. (13 mm) nap roller cover  
D 45° swivel adapter  
ti6623a  
3600 psi (24.8 MPa, 248 bar) Maximum Fluid Inlet Pressure  
*
The best operating pressure is the lowest pressure that provides  
*
an even paint supply to the roller and typically does not exceed  
300 psi (2.1 MPa, 21 bar).  
CAUTION  
Never leave water in the pump, gun, or pressure roller.  
Doing so could cause corrosion and damage from freezing.  
For storage, flush the system with Graco Pump Armort or  
mineral spirits/paint thinner.  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441  
ECOPYRIGHT 2001, GRACO INC.  
Graco Inc. is registered to I.S. EN ISO 9001  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pressure Roller, Model  
244279, Series C  
Cleaning  
23  
This is the procedure for flushing the pressure roller.  
The pump and gun you are using may have additional  
flushing steps, such as cleaning filters and screens.  
See the pump and gun flushing instructions.  
4
1
NOTE: Leave the pressure roller attached to the gun  
for this procedure.  
See Pressure Relief  
Procedure on page 2.  
5
2
1. Relieve the pressure.  
2. Remove roller cover (19) and diffuser (23) from  
roller frame as follows (see Parts Drawing):  
12  
19  
a. Using your thumb, press down on clip (5) to  
release end caps (2 &4), diffuser (23) and  
roller cover (19) into a pail.  
ti10641a  
14  
b. Remove roller cover (19) from diffuser (23).  
c. Pull end caps (2 & 4) off diffuser (23).  
3. Clean roller cover (19), caps (2 & 4) and diffuser  
(19) with water or a compatible fluid for oil–based  
materials.  
4. Place roller frame (1) in paint pail. Be sure the  
holes in roller frame (1) are facing inside the paint  
pail.  
5. Prime pump with water or flushing fluid for  
oil–based materials. Use the lowest pump priming  
pressure setting.  
7
6. Turn prime/spray valve to SPRAY.  
17  
NOTE: Perform Step 7 at the lowest pressure  
possible.  
7*  
7. Trigger gun until flushing fluid begins to dilute the  
paint.  
Parts List  
8. Place roller frame (1) in another bucket and  
continue flushing until fluid coming out of the roller  
frame (1) is clear.  
Ref.  
No.  
Part No. Description  
Qty.  
9. Shut off the pump. Turn prime/spray valve to  
1
2
4
FRAME, roller  
CAP, end (includes seal and retainer)  
CAP, end (includes seal, retainer, and  
o–ring)  
CLIP, roller  
GASKET  
1
1
PRIME.  
245999  
246277  
Storage  
1
1
2
5
7
197106  
15H622  
If you are going to store the airless equipment for an  
extended period of time after flushing with water-base  
fluid, flush again with Graco Pump Armor or mineral  
spirits/paint thinner. Leave the fluid in the system  
during storage.  
12  
14  
19  
115524  
232122  
107590  
GASKET  
1
1
EXTENSION, 20 in. (50 cm)  
ROLLER, cover, 9 inch,  
1/2 in. (13 mm) nap  
1
2
1
23  
25  
15B065  
224399  
DIFFUSER  
SWIVEL, 45°  
309323  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Graco Standard Warranty  
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the  
date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco,  
Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be  
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by  
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or  
substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility  
of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,  
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for  
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The  
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect  
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and  
transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT  
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other  
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any  
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the  
date of sale.  
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection  
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured  
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide  
purchaser with reasonable assistance in making any claim for breach of these warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment  
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,  
breach of warranty, the negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings  
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties  
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures  
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.  
TO PLACE AN ORDER, contact your Graco distributor, or call 1–800–690–2894 to identify the distributor closest to you.  
All written and visual data contained in this document reflect the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
This manual contains English. MM 309323  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441  
309323E  
8/2001 Rev. 9/2007  
4
309323  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Grizzly Saw G1023ZX User Manual
Guardian Technologies Portable Generator 5209 User Manual
Harman Kardon Home Theater System HKTS 5 User Manual
Hasbro Games 06591 User Manual
Hasbro Games 08189 User Manual
Honeywell Humidifier HE280 User Manual
Honeywell Thermostat CT1700A User Manual
Hotpoint Refrigerator HTS17CBT User Manual
HP Hewlett Packard Crib Toy 8510w User Manual
HP Hewlett Packard Portable Media Storage 9840 User Manual