Instructions–Parts List
Quiet ViscountR II
Hydraulic Motor
308048K
ENG
Used as hydraulic drive for reciprocating pumps.
For professional use only.
Model 223646, Series B
1500 psi (10 MPa, 103 bar) Maximum Hydraulic Fluid Input Pressure
Patent No. 4,792,291
Foreign Patents Pending
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
Table of Contents
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Mounting Hole Layout . . . . . . . . . . . . . . . . . . . . 14
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Graco Phone Number . . . . . . . . . . . . . . . . . . . . 16
04471
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
SKIN INJECTION HAZARD
Spray from the gun, hose leaks or ruptured components can inject fluid into your body and cause
extremely serious injury, including the need for amputation. Fluid splashed in the eyes or on the skin
can also cause serious injury.
D
F
l
u
i
d
i
n
j
e
c
t
e
d
i
n
t
o
t
h
e
s
k
i
n
m
i
g
h
t
l
o
o
k
l
i
k
e
j
u
s
t
a
c
u
t
,
b
u
t
i
t
i
s
a
s
e
r
i
o
u
s
i
n
j
u
r
y
.
G
e
t
i
m
m
e
d
i
a
t
e
s
u
r
g
i
-
cal treatment.
D Do not point the gun at anyone or at any part of the body.
D Do not put your hand or fingers over the spray tip.
D Do not stop or deflect leaks with your hand, body, glove or rag.
D Do not “blow back” fluid; this is not an air spray system.
D Always have the tip guard and the trigger guard on the gun when spraying.
D Check the gun diffuser operation weekly. Refer to the gun manual.
D Be sure the gun trigger safety operates before spraying.
D Lock the gun trigger safety when you stop spraying.
D
F
o
l
l
o
w
t
h
e
P
r
e
s
s
u
r
e
R
e
l
i
e
f
P
r
o
c
e
d
u
r
e
o
n
p
a
g
e
7
i
f
t
h
e
s
p
r
a
y
t
i
p
c
l
o
g
s
a
n
d
b
e
f
o
r
e
c
l
e
a
n
i
n
g
,
checking or servicing the equipment.
D
T
i
g
h
t
e
n
a
l
l
f
l
u
i
d
c
o
n
n
e
c
t
i
o
n
s
b
e
f
o
r
e
o
p
e
r
a
t
i
n
g
t
h
e
e
q
u
i
p
m
e
n
t
.
D
C
h
e
c
k
t
h
e
h
o
s
e
s
,
t
u
b
e
s
,
a
n
d
c
o
u
p
l
i
n
g
s
d
a
i
l
y
.
R
e
p
l
a
c
e
w
o
r
n
,
d
a
m
a
g
e
d
,
o
r
l
o
o
s
e
p
a
r
t
s
i
m
m
e
d
i
a
t
e
l
y
.
Permanently coupled hoses cannot be repaired; replace the entire hose.
D
U
s
e
o
n
l
y
G
r
a
c
o
a
p
p
r
o
v
e
d
h
o
s
e
s
.
D
o
n
o
t
r
e
m
o
v
e
a
n
y
s
p
r
i
n
g
g
u
a
r
d
t
h
a
t
i
s
u
s
e
d
t
o
h
e
l
p
p
r
o
t
e
c
t
t
h
e
hose from rupture caused by kinks or bends near the couplings.
MOVING PARTS HAZARD
Moving parts can pinch or amputate your fingers.
D
K
e
e
p
c
l
e
a
r
o
f
a
l
l
m
o
v
i
n
g
p
a
r
t
s
w
h
e
n
s
t
a
r
t
i
n
g
o
r
o
p
e
r
a
t
i
n
g
t
h
e
p
u
m
p
.
D
B
e
f
o
r
e
s
e
r
v
i
c
i
n
g
t
h
e
e
q
u
i
p
m
e
n
t
,
f
o
l
l
o
w
t
h
e
P
r
e
s
s
u
r
e
R
e
l
i
e
f
P
r
o
c
e
d
u
r
e
o
n
p
a
g
e
7
t
o
p
r
e
v
e
n
t
t
h
e
equipment from starting unexpectedly.
308048
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
FIRE AND EXPLOSION HAZARD
Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and
result in a fire or explosion and serious injury.
D
G
r
o
u
n
d
t
h
e
e
q
u
i
p
m
e
n
t
a
n
d
t
h
e
o
b
j
e
c
t
b
e
i
n
g
s
p
r
a
y
e
d
.
R
e
f
e
r
t
o
G
r
o
u
n
d
i
n
g
o
n
p
a
g
e
6
.
D If there is any static sparking or you feel an electric shock while using this equipment, stop spray-
ing immediately. Do not use the equipment until you identify and correct the problem.
D
P
r
o
v
i
d
e
f
r
e
s
h
a
i
r
v
e
n
t
i
l
a
t
i
o
n
t
o
a
v
o
i
d
t
h
e
b
u
i
l
d
u
p
o
f
f
l
a
m
m
a
b
l
e
f
u
m
e
s
f
r
o
m
s
o
l
v
e
n
t
s
o
r
t
h
e
f
l
u
i
d
being sprayed.
D Keep the spray area free of debris, including solvent, rags, and gasoline.
D Before operating this equipment, electrically disconnect all equipment in the spray area.
D Before operating this equipment, extinguish all open flames or pilot lights in the spray area.
D Do not smoke in the spray area.
D
D
o
n
o
t
t
u
r
n
o
n
o
r
o
f
f
a
n
y
l
i
g
h
t
s
w
i
t
c
h
i
n
t
h
e
s
p
r
a
y
a
r
e
a
w
h
i
l
e
s
p
r
a
y
i
n
g
o
r
w
h
i
l
e
t
h
e
r
e
a
r
e
a
n
y
f
u
m
e
s
in the air.
D
D
o
n
o
t
o
p
e
r
a
t
e
a
g
a
s
o
l
i
n
e
e
n
g
i
n
e
i
n
t
h
e
s
p
r
a
y
a
r
e
a
.
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
D
K
n
o
w
t
h
e
s
p
e
c
i
f
i
c
h
a
z
a
r
d
s
o
f
t
h
e
f
l
u
i
d
y
o
u
a
r
e
u
s
i
n
g
.
D
S
t
o
r
e
h
a
z
a
r
d
o
u
s
f
l
u
i
d
i
n
a
n
a
p
p
r
o
v
e
d
c
o
n
t
a
i
n
e
r
.
D
i
s
p
o
s
e
o
f
h
a
z
a
r
d
o
u
s
f
l
u
i
d
a
c
c
o
r
d
i
n
g
t
o
a
l
l
l
o
c
a
l
,
state and national guidelines.
D
A
l
w
a
y
s
w
e
a
r
p
r
o
t
e
c
t
i
v
e
e
y
e
w
e
a
r
,
g
l
o
v
e
s
,
c
l
o
t
h
i
n
g
a
n
d
r
e
s
p
i
r
a
t
o
r
a
s
r
e
c
o
m
m
e
n
d
e
d
b
y
t
h
e
f
l
u
i
d
a
n
d
solvent manufacturer.
4
308048
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
NOTICE
WARNING
Recommended Hydraulic Oil
Maximum Hydraulic Input Pressure
The maximum safe hydraulic input pressure to this
motor depends on the pressure rating of the dis-
placement pump to which it is connected.
Use Graco-approved Hydraulic Oil, Part No. 169236
(5 gal) or 207428 (1 gal)) or a premium, ISO grade
46 petroleum-based hydraulic oil containing rust and
oxidation inhibitors and anti-wear agents.
Refer to the lower manual and the pump manual
for the maximum fluid working pressure and the
ratio. Never exceed the maximum fluid working
pressure of the pump. Serious injury or damage to
the equipment may result.
Before using any other type of oil in this motor,
contact your Graco distributor. Unauthorized use of
lesser grade oil or substitutes may void the warranty.
Hydraulic Oil Working Temperature
The recommended hydraulic oil operating tempera-
ture is 80–115_ F (27–45_ C). The motor seals will
wear faster and leakage may occur if the pump is
operated at higher oil temperatures.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 7.
If the hydraulic oil temperature approaches 130_ F
(54_ C), check the hydraulic fluid supply cooling
system, filters, etc. and clean or repair as needed.
Be sure you always shut off the supply line shutoff
valve (E) first, and then the return line shutoff
valve. This is to prevent overpressurizing the motor
or its seals. When starting up the hydraulic system,
open the return line shutoff valve first.
Refer to the complete pump manual for detailed instal-
lation information or contact your Graco distributor.
NOTE: A 1 in. npt seal (7) is supplied in a plastic bag
with the motor. Thread the seal onto the threads of
your hydraulic return line fitting (A). Thread the fitting
into the upper housing (53) and torque as needed.
Then tighten the seal (7) against the motor to provide a
secure seal. See Fig. 1.
NOTICE
Keep the hydraulic system clean
53
To reduce the risk of damaging the hydraulic power
supply, blow out all hydraulic lines with air, flush
thoroughly with solvent, and then blow out with air
again before connecting the lines to the motor.
A
Always plug the hydraulic inlets, outlets and lines
when disconnecting them to avoid introducing dirt
and other contaminants into the system.
Carefully follow the manufacturer’s recommendations
on reservoir and filter cleaning, and periodic changes
of hydraulic fluid.
04467
7
Fig. 1
308048
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
4. Spray gun: obtain grounding through connection to
Grounding
a properly grounded fluid hose and pump.
5. Fluid supply container: according to local code.
6. Object being sprayed: according to local code.
WARNING
For your safety, read the FIRE AND EXPLOSION
HAZARD WARNINGS on page 4, and ground
your entire system as instructed below. This sec-
tion also includes details on how to connect the
grounding wire and clamp to the various hydraulic
motors.
7. Any pails used when flushing: Use only metal,
grounded pails when flushing. Make firm metal-to-
metal contact between the metal part of the spray
gun and the pail. Use the lowest possible pres-
sure.
Proper grounding is an essential part of maintaining a
safe system.
8. To maintain grounding continuity when flushing or
relieving pressure, always hold a metal part of the
gun firmly to the side of a grounded metal pail, and
then trigger the spray gun.
To reduce the risk of static sparking, ground the pump.
Check your local electrical code for detailed grounding
instructions for your area and type of equipment. Be
sure to ground all of this equipment:
1. Pump: use a ground wire and clamp as shown to
the right. Loosen the locknut (A) of the grounding
lug and washer. Insert one end of the wire (B) in
the grounding lug (14) and tighten the locknut
securely. See Fig. 2. Connect the other end of the
wire to a true earth ground, as recommended by
your local code. Order Part No. 237569, Ground
Wire and Clamp.
B
2. Hydraulic hoses and fluid outlet hoses: use only
electrically conductive hoses.
14
A
3. Hydraulic power supply and air compressor:
04468
Fig. 2
follow manufacturer’s recommendations.
6
308048
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Pressure Relief Procedure
Before you start:
Be sure you have all necessary parts on hand.
WARNING
1. Repair Kit 223654 is available. The kit must be
purchased separately. An asterisk behind a refer-
ence number in the parts list, for example (21*),
indicates that the part is included in the repair kit.
SKIN INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally. Fluid
under high pressure can be injected through the
skin and cause serious injury. To reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
2. Clean all parts as you disassemble them and
inspect them for wear or damage. Replace parts
as necessary. Use Loctite
r
TL–242 thread
sealant, or the equivalent, when thread sealant is
specified.
D are instructed to relieve the pressure,
D stop spraying,
D check or service any of the system equipment,
D or install or clean the spray tip.
Disassembly (Refer to Fig. 3)
NOTE: Use all the replacement parts that are in the
repair kit.
1. Lock the gun trigger safety.
1. Flush the displacement pump if possible.
2. Shut off the hydraulic power supply.
3. Close the supply line shutoff valve, and then the
return line shutoff valve.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 7.
4. Unlock the gun trigger safety.
5. Hold a metal part of the gun firmly to the side of a
grounded metal pail, and trigger the gun to relieve
pressure.
2. Relieve the pressure.
6. Lock the gun trigger safety.
3. Stop the pump at the bottom of its stroke.
7. Open the drain valve (required in your system),
having a container ready to catch the drainage.
NOTICE
Avoid getting dust or dirt in the motor during service.
Cleanliness is essential when repairing an hydraulic
motor.
8. Leave the drain valve open until you are ready to
spray again.
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, very slowly loosen the
tip guard retaining nut or hose end coupling and relieve
pressure gradually, then loosen completely. Now clear
the obstruction.
4. Disconnect the displacement pump hoses. Discon-
nect the hydraulic hoses and plug all hydraulic
connections and lines to prevent contamination.
308048
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
13. Unscrew the top and bottom compression nuts (B)
Disassembly (continued – refer to Fig. 3)
on the hydraulic tube (4). Rotate the upper housing
(53) and remove the tube, being careful not to
damage the flare (A). Allow the oil to drain from
the motor into the pan.
NOTICE
When removing the displacement pump, hold it
securely. The pump is heavy and could fall off the
motor.
NOTE: With the tie rods removed, the assembly may
separate at the joints between the cylinder (29) and
the upper and lower housings (53 and 25).
5. Disconnect the displacement pump from the
motor, as explained in your separate pump manu-
al.
14. Rock the upper housing (53) to work it free and lift
it about 3 inches off the cylinder (29). The cylin-
der can stay in the lower housing (25).
6. Place the hydraulic motor in a bench vise.
7. Push or lightly tap the piston (30) up as far as
possible.
15. Hold the trip rod (31) with an adjustable wrench on
the flats of the rod, and remove the top hex nut
(46) from the trip rod.
NOTE: The tie rod nuts (19), socket screws (51), cap
screws (36), and retainer (34) are fastened with Loc-
titer TL–242. Heat may be used sparingly to soften
adhesive sealant during disassembly.
16. Remove the upper housing (53).
17. Remove the trip rod guides (37), compression
springs (45) and valve spool (38) from the upper
housing. Inspect the bearing inside of the guide
(35) in place. If bearing is damaged replace item
35.
8. Remove the cap screws (12), the drip pan (16),
the drip cover (18), and machine screw (20) before
loosening the tie rod nuts. Then remove the four
tie rod nuts (19). Loosen the nuts (B) on the hy-
draulic tube (4) and loosen the tie rods (57).
NOTE: Inspect the trip rod (31) above the shoulder for
damage. There must be no reduction in diameter.
Replace if necessary.
9. Remove the motor from the vise and lay it in a
pan.
10. Remove one detent assembly: retaining plug (39),
o-ring (41), spring (40), ball guide (42) and ball
(43). If the ball or other parts stick in the upper
housing (53), turn the motor over and tap lightly.
Do not allow the parts to fall into the motor. Repeat
the procedure for the other detent assembly.
18. Pull the trip rod and piston from the lower housing
(25) and cylinder (29). Place the piston flats (30) in
a vise; tighten the vise on the flats of the piston.
Use a face spanner to remove the retainer (34).
Remove the trip rod (31) from the piston (30).
19. Remove the trip rod locknut (27) and piston stop
(28). If the piston is replaced, remove the spring
(26) to use in the new piston.
11. Remove the tie rods (57), but do not remove the
crown nuts (44).
12. Remove the socket screws (51) and the end cap
(47). Pull the stop plug (48) from the upper hous-
ing (53).
20. Remove the bearing (23), packings (24), and
o-ring (21).
8
308048
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
50
51
47
48
44
52
33*
57
*49
55a
55
53
B
29
54
54a
56
43
33*
42
40*
41
B
7a
39
24*
25
54
7
58
5
54a
46
6a
37
A
B
4
6
45*
31
23*
24*
38
*45
37
3
3a
34
B
A
A
28
27
21*
2
35
36
*32
26
14
15
19
18
30
20
16
13
12
*17
NOTE: Circled letters refer to connected points.
04466
Fig. 3
308048
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
10. Remove the adjustable wrench. Seat the upper
Reassembly (Refer to Fig. 4)
housing (53) onto the cylinder (29), so the tube
1. Install the bearing (23*) in the lower housing (25).
Lubricate the seals (24*) with hydraulic oil. Install
them in the lower housing (25) with the lips facing
up toward the top of the motor.
fittings align with those on the lower housing (25).
Reinstall the hydraulic tube (4) and loosely tighten
the compression nuts.
2. Install the o-ring (21*) onto the lower housing (25).
11. Replace the o-ring (49*) on the stop plug (48).
Seat the plug into the upper housing (53).
3. Place the piston flats in a vise. Install the spring
(26) inside the piston (30). The compression rings
(32*) must be positioned with the joints about 180
opposed. Be sure the o-ring (17*) is in place.
_
12. Install the end cap (47), using thread sealant on
the socket screws (51).
4. Install the piston stop (28) and locknut (27) on the
trip rod. Torque the nut to 117–123 in-lb (13.2–13.9
N.m). Slide the trip rod (31) into the piston (30).
Apply thread sealant to the retainer (34) threads.
With the piston flats in a vise, tighten the retainer
until it is flush or below the piston surface. This is
important to prevent the retainer from backing out
during operation and damaging the motor.
13. Lubricate the threads of the tie rods (57) and install
them with lockwashers (52). If the crown nuts (44)
were removed, reinstall them and torque them
onto the rods to 70–80 ft-lb (95–108 N.m).
14. Torque tie rods into base, apply thread sealant to
tie rod threads, then torque the tie rod nuts (19) to
70–80 ft–lb (95–108 N.m).
NOTE: Set base (2) on workbench during reassembly.
15. With the motor on its side, install one detent
assembly: the ball (43), guide (42) with the con-
cave surface toward the ball, spring (40*), o-ring
(41) and retaining plug (39). Torque the plug to
145–160 in-lb (16–18 N.m). Repeat for the other
side of the motor.
5. Install the o-ring (33*) onto the cylinder (29). Install
the cylinder (29) into the lower housing (25).
6. Install the trip rod and piston into the cylinder (29)
and lower housing (25) so the piston is recessed at
least 1 inch (25 mm) from the top of the cylinder.
7. If the bearing and guide (35) was removed, install
it on the upper housing (53) with the three screws
(36) (apply thread sealant).
16. Slide the drip cover (18) onto the piston (30) up to
the o-ring (17). Install screw (20) into the piston.
Attach the drip pan (16) to the base using screws
(12).
8. Hold the flats of the trip rod with an adjustable
wrench and install the upper housing (53). The trip
rod will protrude from the top.
17. Snugly tighten the compression nuts on the hy-
draulic tube (4) and torque to 60–80 ft-lb (81–108
N.m).
9. Slide the lower trip rod guide (37) and spring (45)
onto the trip rod. Install the spool (38) with the
detent at the top. Install the top spring (45) and
guide (37) on the trip rod. Install the top hex nut
(46). Torque the nut to 82–88 in-lb (9.3–9.9 N.m).
18. Install the motor on the displacement pump. Re-
connect all fluid lines. Be sure the ground wire is
connected before operating the pump.
10 308048
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
50
51
33*
5
47
48
44
52
*49
4
57
29
3
4
55a
55
53
B
54
54a
56
43
42
33*
24*
40*
41
39
B
7a
9
2
54
7
58
5
54a
46
8
6a
25
37
A
6 B
6
45*
31
4
38
23*
24*
*45
37
3
3a
2
34
5
7
B
A
6
A
28
27
21*
2
35
5 36
*32
26
1
14
15
1
Rings must be positioned with joints opposed
Lips must face up toward top of motor
Lubricate threads
2
5
4
3
4
5
6
19
18
Torque to 70–80 ft-lb (95–108 N.m)
30
20
16
Apply thread sealant
Torque to 60–80 ft-lb (81–108 N.m)
13
12
7
Torque to 117–123 in-lb (13.2–13.9 N.m)
*17
8
9
Torque to 82–88 in-lb (9.3–9.9 N.m)
Torque to 145–160 in-lb (16–18 N.m)
04466
Fig. 4
308048 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 223646, Series B
50
33*
57
51
47
48
44
52
*49
55a
55
53
B
29
54
54a
56
43
33*
42
40*
41
B
7a
39
24*
25
54
7
58
5
54a
46
6a
A
37
6
45*
31
4
23*
24*
38
*45
3
3a
34
37
A
28
27
21*
2
35
36
Y
1
*32
26
14
15
9Y
Y
1
1
19
30
20
18
13
16
*17
12
NOTE: See the service section for important
torque and lubrication information.
NOTE: Circled letters refer to connected points.
04466
12 308048
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 223646, Series B
Ref.
No.
Ref.
No.
Part No. Description
Qty.
Part No. Description
Qty.
1
2
3
Y
290331
186221
110797
LABEL, instruction, English
BASE
ELBOW, male, 3/4 npt
Includes item 3a
.O-RING, nitrile rubber
TUBE
ADAPTER, 3/4 npt (f) x
1–1/16–12
TEE, 7/8–14 unf–2a x 1 1/16–
12un–2a, 37_ flare for 3/4 in. dia.
tube, Includes item 6a
.O-RING, nitrile rubber
ADAPTER, 1 –11-1/2 npt x
1 5/16–12un–2a, Includes item 7a
.O-RING, nitrile rubber
LABEL, identification not shown
LABEL, warning
SCREW, type “u” drive,
No. 4 x 0.188 in.
PLATE, warning
SCREW, cap, hex hd;
1/4–20 x .0.5 in.
ADAPTER, barbed hose, 1/8
npt x 0.25 in. (6.4 mm) ID hose
GROUNDING LUG
WASHER
PAN, drip
O-RING, nitrile rubber
COVER, drip
NUT, hex jam, 5/8–18
SCREW, machine, hex hd;
No. 10–20 x 0.375 in.
O-RING, buna–N
1
1
33*
34
35
36
166071
171398
210292
108538
O-RING, nitrile rubber
RETAINER
BEARING and GUIDE
SCREW, soc flat hd, self locking,
1/4–20 x 1/2 in.
GUIDE, trip rod
SPOOL, valve
RETAINER, spring
SPRING, helical compression
O-RING, nitrile rubber
GUIDE, ball
2
1
1
1
1
1
3a
4
5
110926
210108
112574
3
2
1
2
2
2
2
2
4
2
1
1
1
1
1
37
38
39
40*
41
42
43
44
45*
46
47
48
49*
50
51
183659
183658
186222
108522
110801
167210
101701
104143
171411
104105
180953
171416
104093
108132
101864
1
6
110791
1
1
6a
7
110926
110876
BALL, 1/4 in. dia.
NUT, crown, 5/8–18
SPRING, compression
NUT, hex lock, 1/4–20
CAP, end
PLUG, stop
O-RING, nitrile rubber
RING, lift
CAPSCREW, soc hd,
5/16–18 x 1 in.
LOCKWASHER, spring, 5/8 in.
HOUSING, upper
ELBOW, 90_ , 7/16–20 unf–2a(m)
x 9/16–18 unf–2a(m), 37_ flare for
3/8 in. dia. tube, Includes item 54a
.O-RING, nitrile rubber
PLUG, 9/16–18 unf–2b,
Includes item 55a
.O-RING, nitrile rubber
TUBE, drain
ROD, tie
1
1
1
1
7a
8
110927
183695
172975
100508
9Y
10
4
1
11
12
Y
172815
100333
3
4
1
3
52
53
54
100128
186217
110792
13
103875
1
1
1
1
1
1
4
14
15
16
17*
18
19
20
104029
104582
210110
165295
171397
100155
101577
2
2
54a
55
110801
110799
1
1
1
4
55a
56
57
110925
223608
171405
105430
1
1
21*
23*
110800
186223
58
NUT, seal, 1 in. npt
supplied in a plastic bag
BEARING, piston,
1
bronze-filled PTFE
SEAL, u-cup, polyurethane
HOUSING, lower
SPRING, compression
NUT, hex, self-locking, 5/16–18
STOP, piston
CYLINDER
PISTON
ROD, trip
RING, piston, compression
1
2
1
1
1
1
1
1
1
2
*
These parts are also included in Repair Kit 223654,
which may be purchased separately.
24*
25
26
27
28
29
30
31
32*
110795
186218
104664
103450
181243
186219
188087
171407
104103
Y Replacement Danger and Warning labels, tags and
cards are available at no cost. Label 290331 is also
available in the following languages:
German (Part No. 290396)
French (Part No. 290397)
Spanish (Part No. 290398).
308048 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Hole
Layout
Dimensions
1
2
5
4
6
3
2
4
1
2
02589
1
2
3
Four 0.437 in. (11.1 mm) dia. mounting holes
3.712 in. (9.45 cm)
3
3.464 in. (8.79 cm)
1
2
1 in. npt Outlet
4.0 in. (9.84 cm)
4
5
6
3/4 in. npt Inlet
2.0 in. (5.08 cm)
11.25 in. dia. (285.8 mm)
24.94 in. (633.8 mm)
1.8 in. to top of 4.69 in. stroke
Three 5/8–11 UNC (2B) tapped holes
3
4
5
5
7
Gasket 161806 is not shown. Order Separately
02631
14 308048
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Category
Data
Maximum hydraulic fluid input pressure
1500 psi (10 MPa, 103 bar). Also see the WARNING on
page 5.
Maximum hydraulic fluid flow
Hydraulic fluid consumption
Effective piston area
Piston rod diameter
12 gpm (45.6 liter/min)
1 gal. (3.8 liter) per 5 cycles
2
4.9 sq. in. (31.6 cm )
2.5 in. (64 mm)
Stroke length
4.69 in. (119.1 mm)
7300 psi (32 472 N)
approx. 96 lb. (43.5 kg)
Thrust at 1500 psi (10 MPa, 103 bar)
Weight
Loctiter is a registered trademark of the Loctite Corp.
Sound Data
Hydraulic Pressure
dB(A) at 20 cycles
per minute
dB(A) at 30 cycles
per minute
dB(A) at 60 cycles
per minute
1500 psi (10 MPa, 103 bar)
70
78
79
308048 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Warranty and Limitation of Liability
Graco warrants all equipment listed in this manual which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of
any special extended or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or
replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed,
operated and maintained in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or
substitution of non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance or structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT
NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, gas engines,
switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance
in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties
reconnaissent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures
judiciaires exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you:
Phone: 612–623–6921 or Toll Free: 1–800–328–0211 Fax: 612–378–3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 308048
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
Copyright 1990, Graco Inc. is registered to ISO 9001
Revised 08/2010
16 308048
Download from Www.Somanuals.com. All Manuals Search And Download.
|