Operation
™
333428E
JetRoller
EN
For spray rolled application of architectural paints and coatings.
Not approved for use in explosive atmospheres or hazardous locations.
Model 24U170, 24U172, 24V820, 24V926, 24X605, 24V490,
24V491, 24V492, 24V493, 24W128, 24W129
3600 psi (24.8 MPa, 248.2 bar) Maximum Working Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual and in your sprayer, in-line valve, and
™
CleanShot manuals. Save all instructions.
Related Manuals
™
309642
CleanShot Shutoff Valve
™
309315
Contractor In-Line Valve
ti23593b
180º Spray Nozzle
308244
Roller
Frame
Includes
Model
TIP
In-Line Valve 45° Swivel
CleanShot 180° Swivel
24U170
24U172
24V820
24V926
24X605
24V490
24V491
24V492
24V493
24W128
24W129
9”
9”
9”
LTX721
9.5”
10.5”
18 cm
25 cm
18 cm
25 cm
12” - 18”
12” - 18”
LTX821
PAA515
PAA721
PAA515
PAA721
WR1223*
* - For 18” setting, see page 5 for additional tip options.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
•
•
Do not operate the unit when fatigued or under the influence of drugs or alcohol.
Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See
Technical Data in all equipment manuals.
•
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment
manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request
MSDS from distributor or retailer.
•
•
•
Do not leave the work area while equipment is energized or under pressure.
Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.
Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s
replacement parts only.
•
Do not alter or modify equipment. Alterations or modifications may void agency approvals and create safety haz-
ards.
•
•
•
•
•
•
Make sure all equipment is rated and approved for the environment in which you are using it.
Use equipment only for its intended purpose. Call your distributor for information.
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
Do not kink or over bend hoses or use hoses to pull equipment.
Keep children and animals away from work area.
Comply with all applicable safety regulations.
PRESSURIZED ALUMINUM PARTS HAZARD
Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical reaction and
equipment rupture. Failure to follow this warning can result in death, serious injury, or property damage.
•
Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids contain-
ing such solvents.
•
•
Do not use chlorine bleach.
Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier for com-
patibility.
CALIFORNIA PROPOSITION 65
This product contains a chemical known to the State of California to cause cancer, birth defects or other
reproductive harm. Wash hands after handling.
3. Close the bleed-type master air valve. Disengage
Setup
the trigger lock.
4. Rotate the CleanShot knob fully counter-clockwise
to the FLUSH position.
Pressure Relief Procedure
5. Hold the metal extension firmly to a grounded metal
pail. Trigger the gun to relieve pressure.
Follow the Pressure Relief Procedure whenever
you see this symbol.
6. Engage the trigger lock.
7. Open all fluid drain valves in the system, having a
waste container ready to catch drainage. Leave
drain valve(s) open until you are ready to spray
again.
This equipment stays pressurized until pressure is
manually relieved. To help prevent serious injury
from pressurized fluid, such as skin injection,
splashing fluid and moving parts, follow the Pressure
Relief Procedure when you stop spraying and before
cleaning, checking, or servicing the equipment.
8. If you suspect the spray tip or hose is clogged or
that pressure has not been fully relieved:
a. VERY SLOWLY loosen tip guard retaining nut
or hose end coupling to relieve pressure gradu-
ally.
b. Loosen nut or coupling completely.
c. Clear hose or tip obstruction.
1. Engage trigger lock.
2. Remove roller handle.
333428E
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
For best results use sprayer
pressure shown below. Al-
ways spray at the lowest
pressure necessary to get de-
sired results.
Read your sprayer, in-line valve, and CleanShot manuals.
1
2
Assemble JetRoller as shown. Snug extension fittings with wrenches.
Then tighten another 1/4 turn [~100 in-lb (11 N•m)]. Attach to gun
sprayer hose. Prime sprayer as directed in sprayer manual.
OK
1500
1000
2000
103.4
10.3
68.9
6.89
2500
500
bar
MPa
0
ti23592a
3000
PSI
ti23598a
3
Adjust CleanShot position so
spray fan hits below roller cover.
OK
ti23643a
To narrow pattern, loosen roller handle and
move roller cover toward CleanShot. To
widen pattern, loosen roller handle and
move roller cover away from CleanShot.
Quickly trigger once and release to check pattern. Pattern
should be as wide as roller.
NOTE: CleanShot knob may be adjusted to optimize spray fan.
4
ti23640a
ti23647a
4
333428E
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Spray and roll on down stroke, release trigger and roll on upstroke. For best
results near floors and baseboards, release trigger 12-24” (30-60 cm) above
floor and continue to roll to bottom on down stroke. Back roll on upstroke.
NOTE: See your in-line valve manual for changing the spray tip and for
clearing a clog.
6
Hand roll sensitive wall areas
(outside corners, adjacent walls,
etc.).
5
50%
ti23614a
7
Read your sprayer, in-line valve,
and CleanShot manuals for clean-
ing instructions.
17
4
11
17a
1
17b
14
17c
17d
7
15
8
6
5
17e
3
2
12
18
16
9
8
8
ti24116b
Part
Ref. Number Description
Part
Ref. Number Description
Part
Ref. Number Description
12 224399 SWIVEL, 45°
Qty
1
Qty
Qty
1
1
1
24V829 HANDLE, roller, 9”
24V937 HANDLE, roller, 9.5”
24X651 HANDLE, roller, 10.5”
24V830 HANDLE, roller, 18 cm
24V831 HANDLE, roller, 25 cm
24V832 EXTENSION, JetRoller
includes 8
PAA821 TIP, spray, latex, rac x,
40 cm
WR1223 TIP, spray, latex, rac x,
13 222385 TAG, warning (not
shown)
18”
14 235486 SWIVEL, 180° includes 8
15 17A078 PAD, friction
16 24W131 KIT, arm, 18”
17 24W130 KIT, handle, roller 18”
includes 16 qty 2, 17a-e
17a 24X633 KIT, cap
17b WR1223 TIP, spray, rac x
17c 17D651 KIT, nut, hex, flange,
head
17d 24X632 HANDLE
17e 24X631 KIT, handle includes 16
qty 2
18 17D695 TAG, instructions
Replacement Danger and Warning labels,
tags, and cards are available at no cost.
1
1
2
1
5
6
246215 GUARD, rac x w/ seat
and seal
232122 EXTENSION, roller,
fixed (0.5M) (includes 8)
244161 VALVE, in-line
15H622 GASKET
1
1
2
3
4
1
1
1
287030 VALVE, spray,
7
8
1
1
1
1
CleanShot includes 8
LTX721 TIP, spray, latex, rac x,
9”, 9.5”, and 14”
1
1
9 17B476 LABEL, warning
11 24V833 KIT, repair, 9” roller
frame
LTX821 TIP, spray, latex, rac x,
10.5”
1
1
24V938 KIT, repair, 9.5” roller
PAA515 TIP, spray, latex, rac x,
18 cm
frame
PAA721 TIP, spray, latex, rac x,
1
25 cm
333428E
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 333428
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Revision E, March 2015
Download from Www.Somanuals.com. All Manuals Search And Download.
|