Read all instructions BEFORE
Failure to follow
instructions coul
assembly and use of this product.
Keep instructions for future use.
We recommend that you keep these instructions
with your Pack ’N Play. A storage pocket has been
provided for them on the bottom panel of your unit.
Setting Up the Pack ’N Play
!
THIS PRODUCT REQUIRES ADULT ASSEMBLY.
!
Keep fingers clear of top corners during setup.
Be sure Pack ’N Play is completely set up before use.
Check that the four top rails are completely latched, the
center of the floor is pushed down, and the mattress is
flat and secured by the VELCRO® straps. Always follow
the instructions in the owner’s manual to set up the
Pack ’N Play.
®
Pack ’N Play
Bassinet
®
!
!
When using the bassinet make sure VELCRO patches
underneath mattress firmly attach to bassinet mesh.
OWNER’S
MANUAL
Before each use, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges.
Do not use Pack ’N Play if any parts are missing
or broken. Call 1-800-345-4109 for replacement parts
or owner’s manual. Do not substitute parts.
Model No. _________
Serial No. _________
Using the Pack ’N Play
Dear Customer,
!
The Pack ’N Play can be used as a playard, bassinet or
Please fill in the model and serial numbers
above from the label in the center of the
bottom of your new Pack ’N Play Bassinet.
sleeping crib. When used as a playard, never leave child
unattended and always keep child in view. When used as
a sleeping crib or bassinet, you must still provide the
supervision necessary for the continued safety of your
child.
Models 9045, 9046, 9346, 9640,
9643, 9716, 9726, 9741, 9743,
9745 & 9746
!
Always keep the Pack ’N Play away from hazards in the
area that may injure your child.
!
Do not add padding or other objects inside the Pack ’N
Congratulations on your purchase of a
Graco® Pack ’N Play® Bassinet!
Play that will permit your child to climb out.
!
Stop using this product when your child reaches
35 inches (890 mm) in height, weighs more than 30
pounds (14 kg), or is able to climb out.
Graco is the recognized leader in the design
and manufacture of quality baby products.
We believe your new Graco® Pack ’N Play®
Bassinet is a wise choice, promising many
hours of enjoyment for your baby.
!
Do not modify Pack ’N Play or add any attachments
that are not listed in the owner’s manual, including an
add-on bassinet.
Your Pack ’N Play® may be used as a
playard, portable crib or bassinet.
Using the Bassinet
!
Use bassinet with only one child at a time.
Customer Satisfaction
Our goal is to make every product the best
!
The bassinet must be fully assembled and installed,
including top rails, snaps and bottom pad, before using.
it can be! We are also committed to supporting our
products after purchase. If you would like to speak
to Graco about your product, please contact our
Customer Service Department at 1-800-345-4109
Our knowledgeable staff will be ready to answer
any questions you may have concerning parts, use
or maintenance. When you call, please have the
model and serial numbers ready so your call
may be processed quickly and efficiently.
Failure to
instructions coul
© 1999 Graco 361-10-99
2
Download from Www.Somanuals.com. All Manuals Search And Download.
At first your Pack ’N Play may be like a new pair of
shoes. You may need to break it in by slightly stretching
the netting and fabric. If the center does not stay down,
place some weight (several books) in the center of the
unit and let it stand overnight.
Step 3.
The top rail has a center piece
with two tubes hidden under the
fabric. The button on the bottom
of the center piece releases the
two tubes when it is pushed up.
To Use as a
Playard/Portable Crib
Place mattress into your unit
with padded side up.
Center
piece
Always use your unit with
mattress installed soft side up.
Tube
Slide the two VELCRO® straps
through slots in bottom of Pack
’N Play and fasten to VELCRO®
on underside. This will prevent
mattress from moving.
Push UP button
under fabric
Your Pack ’N Play is ready to
use.
To fold the top rail:
!
Lift up slightly on the top rail.
!
Push up on the button located under
®
!
To Fold Your Pack ’N Play
the symbol to release the two tubes.
!
Push down.
Step 1.
HINTS:
Lower the back flap. Apply
locks on wheels or casters,
if present. Release the two
VELCRO® straps under the
Pack ’N Play, and remove the
mattress.
!
If top rails do not unlatch, lift
the center of the floor higher.
!
!
Both tubes must be released
for the top rail to fold.
!
Step 2.
IMPORTANT:
Step 4.
Raise center halfway
BEFORE unlocking
rails.
Pull center up all the way.
Grasp the red handle
on the center of the floor
as shown.
Push down and turn
handle. Then pull up
approximately halfway
to the top rails.
361-10-99
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
®
To Cover Your Pack ’N Play
Step 5.
Gather your unit together.
Do not force.
Models with changing table and wheels:
If unit will not fold, look for a
partially latched top rail. Squeeze
the latch button to release the rail.
Pull the cover over your unit
as shown, making sure carry
handle attached to Pack ’N
Play mattress is lined up with
zipper.
Before pulling bag up, insert
folded changing table into the
side opposite the handle as
shown. Pull bag up to cover
Handle
end. Zip together.
Step 6.
Find the bottom corner belt loop
(only one). This loop is for holding
unit and mattress together while
carrying.
Models with wheels only:
Wheel
Foot
Turn unit upside down, so that
wheels point up. Pull the cover
over your unit. Make sure carry
handle attached to Pack ’N
Play mattress is lined up with
zipper.
Step 7.
Handle
Wrap the mattress around your unit.
Fasten together the VELCRO® straps,
attaching the bottom strap to the
bottom corner belt loop.
Push the plastic end of the bag
over wheels and feet. Turn unit
over and pull bag up to cover
end. Zip together.
Models with feet or
casters and feet:
Pull cover over your
unit. Be sure carry
handle attached to
Pack ’N Play mattress
is lined up with zipper.
Turn unit over. Pull bag
up to cover end. Zip
together.
CARE AND MAINTENANCE
FROM TIME TO TIME CHECK YOUR PACK ’N
PLAY for worn parts, torn material or stitching.
Replace or repair the parts as needed. Use only
Graco® replacement parts.
IF PACK ’N PLAY IS USED AT THE BEACH, you
MUST clean sand off your Pack ’N Play, including
the feet, before packing it into cover. Sand in top
rail lock may damage it.
On certain models:
TO CLEAN PACK ’N PLAY, use only household
soap or detergent and warm water.
The cargo bag opens on either end. Slip the bag over
the Pack ’N Play. Check that the carrying handle
attached to the Pack ’N Play mattress sticks out the
hole in the bag. Zip both ends.
TO WASH CARRY BAG AND FITTED SHEET,
machine wash in lukewarm water on delicate
cycle and drip-dry. NO BLEACH.
7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 4.
BASSINET INSTRUCTIONS
PARTS LIST
Install the end of the tube
without the red spring latch
by placing the loop end into
the slot in the plastic corner.
CHECK that you have all the parts listed below
BEFORE assembling your bassinet.
Step 5.
No tools required.
On the other end of the tube,
pull back on the red spring
latch and insert the loop into
the slot in the plastic corner.
The loop ends must be in the slots in the
corners to secure the bassinet in the Pack ’N Play. Pull
up on the tube and bassinet to ensure that the tube is
in place.
Bassinet
Loop end
Tube (2)
Tube (2)
Wire end
Step 6.
Repeat steps 4 and 5 on the
other side of the bassinet.
Round end
Red spring
latch end
Step 7.
To Install Your Bassinet
Snap both of the end flaps of
the bassinet to the Pack ’N
Play with the eight snaps
(four on each end).
The four bassinet tubes are located in storage pockets
sewn into the bassinet itself.
Step 8.
Step 1.
Place the mattress in the
bassinet soft side up. Push
down on the mattress to
secure the mattress to the
VELCRO® on the bassinet.
Insert wire end of one tube
into the round end of a tube
with a red spring latch.
Repeat with other tubes.
DO NOT use your bassinet
without the mattress
provided by Graco.
Step 2.
Slide the assembled tubes
into the tunnels on the sides
of the bassinet.
To avoid SUFFOCATION, DO NOT use
extra padding such as a water mattress, mattress, or
pillows inside the bassinet. Use ONLY mattress
provided by Graco.
Step 3.
Lift bassinet by the two tubes and lower it into the
Pack ’N Play. Make sure the printed warnings on
the end flap are facing up.
Your bassinet is now ready to use.
361-10-99
9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
To Remove Your Bassinet
Casters*
To apply the locks, push
DOWN on the levers.
Step 1.
Remove the mattress from your bassinet.
Step 2.
To release the locks, lift UP
on the levers.
Unsnap the end flaps from your Pack ’N Play.
Step 3.
Pull back the fabric at one corner of the bassinet to find the
red spring latch.
Wheels*
Step 4.
To apply the locks, push
DOWN on the levers.
Pull the red spring latch back
and lift up the tube.
To release the locks, lift UP
on the levers.
Step 5.
Pull the tube out of the bassinet
and set aside.
Parent Organizer*
Always keep objects out of child’s
reach. Remove parent organizer when child is able
Step 6.
Repeat steps 3, 4 and 5 to remove the other tube.
to pull himself up in the Pack ’N Play.
Step 7.
Step 1.
Use extreme
care when pulling the tubes
apart.
Your parent organizer
includes two plastic dividers.
Slide the plastic dividers
into the two pockets in the
section dividers of the
parent organizer.
Pull the tubes apart by twisting
the tubes as you pull. Store the
tubes in the pockets in the
bassinet.
Step 2.
ACCESSORY INSTRUCTIONS
ON CERTAIN MODELS*
Slide the tube into the
mounts on the end of
your unit.
Side Flap*
Push the button in to
get it started.
You can raise side flap if desired.
Unfasten VELCRO® straps at
bottom of flap. Roll flap up.
Fasten in place with snap loops at
top.
Pull up on the parent
organizer to make sure
that the buttons are
caught on the bottom
of the mounts.
Button
Step 3.
Cargo Bag*
To remove the parent
The cargo bag can be snapped
onto the end of the Pack ’N Play
for easy access. Unzip both ends
and tuck inside the bag.
organizer push in on the
buttons on the bottom of
the tubes and pull up.
Maximum weight 5 lbs (2.3 kg).
11
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 1.
CHANGING TABLE INSTRUCTIONS
(ON CERTAIN MODELS)
Lay changing table flat on floor with short side in front
of you and belt facing up. Gently slide one long tube into
opening on long side exactly as shown.
Parts List
CHECK that you have all parts listed below
BEFORE assembling your changing table.
Long
side
Repeat on other side.
No tools required.
Long tube (2)
Short tube (2)
Short side
Step 2.
Slide one short tube
into opening on end
as shown.
For proper orientation,
be sure folding side of
hinge faces pad as
shown.
Changing pad
Changing
table
Fold side
of hinge
DO NOT insert
other short tube
at this time.
Accessory bag
Step 3.
To Use Your Changing Table
Turn up long tube so
that its end points down.
To protect your child from falls and
other injuries:
Insert end of long tube
into opening on end of
short tube as shown.
DO NOT slide short
tube up around the bend
of long tube until you
• Always stay within arm’s reach of your child when
• using the changing table. Always use waist belt
• when child is on the changing table. Never leave
• child unattended.
Short tube side
have finished next step.
• The changing table is designed for use only with
• this Graco Pack ’N Play. Do not attempt to use it
• with any other product. Before each use, make
• sure the changing table is properly secured to
• the Pack ’N Play by pushing down firmly in the
• middle of the changing table. The changing table
• should not fall.
Make sure fabric does
not get caught in
opening when inserting
long tube into short tube.
Step 4.
• Do not use the changing table as a sleeping or
• play area.
Repeat step 3 on other
end of short tube, then
slide short tube ends up
onto long tubes.
• Weight limit for the changing table is 25 pounds
• (11.3 kg). Do not use the changing table as extra
• storage. Always remove the changing table when
• your child is in the Pack ’N Play.
TO AVOID TEARING
FABRIC, slide this end
up before proceeding
with step 5.
• The Pack ’N Play changing table can be used on
• the floor without being attached to the Pack ’N
• Play. Never place the changing table on a piece of
• furniture, bed, counter or any raised surface from
• which the changing table or your child could fall.
Slide ends up
361-10-99
13
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 5.
To Use Accessory Bag
Repeat steps 2
and 3 on other end
of changing table.
If your bassinet is already installed, unsnap the four
snaps on the bassinet end flap from either end of
Pack ’N Play.
If the short tubes
have been inserted
correctly, the changing
table should be able
to FOLD UP in the
center as shown.
Step 1.
Snap accessory bag
onto end of Pack ’N
Play with four snaps
as shown.
Fold up
Step 6.
Place pad in changing
table with vinyl side up.
Pull belt straps through
holes in center of pad.
Step 2.
Snap bassinet end flap
over the accessory bag
with the four snaps.
Step 7.
To Fold Changing Table
Insert VELCRO® straps
into the four slots at the
corners of changing table
and attach to VELCRO®
on underside of changing
table. This will prevent
pad from moving.
Step 1.
Pull up on waist belt
straps to fold.
Step 2.
Step 8.
Ends of long tubes
must point up when
folded as shown.
Place changing table on
Pack ’N Play as shown.
You may use your changing
table with or without your
bassinet installed. Make
sure tubes are securely
over the sides of the
Ends of tubes
point up
Pack ’N Play.
Check that the changing
table is supported
by the Pack ’N Play by
pushing firmly down into
center of changing table.
Step 3.
To carry or store your changing table
with your folded Pack ’N Play, see
“To Cover Your Pack ’N Play” section
in these instructions.
15
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts
Instructions for ordering Pack ’N Play® parts:
Complete form below. Your Pack ’N Play model number
MUST be included on the form to ensure proper replacement
parts. Your model number can be found on a label on the
center of the bottom of the unit. Payment must accompany
your order.
Parts List:
Price:**
Mattress ......................$17.50
Carry bag ................... $15.00
Cargo bag* ................. $15.00
Caster assembly* ....... $ 5.00 (each)/$8.00 (2)
Wheels* ...................... $ 7.00 (each)/$10.00 (2)
Fitted sheet ................ $10.00
Bassinet parts:
Bassinet ......................$17.00
Wire end tube .............$ 5.00
Round end tube ..........$ 5.00
Changing table parts:
Long tube* .................. $ 9.00
Short tube* ................. $ 7.00
Changing pad* ........... $10.00
Changing table* ..........$15.00
Accessory bag* .......... $ 7.00
* On certain models
** Prices subject to change without notice.
IF YOU NEED HELP
If you have any questions or if you need any part not list-
ed, please call toll-free:
1-800-345-4109
Return the form below with payment to:
GRACO CHILDREN’S PRODUCTS INC.
CUSTOMER SERVICE DEPARTMENT
P.O. BOX 100, MAIN STREET
ELVERSON, PA 19520
Model Number
SHIP TO:
(Must be filled in)
Name
Mattress
Carry bag
Cargo bag
Address
Caster assembly
Wheels
City, State, Zip
Fitted sheet
Bassinet
Wire end tube
Round end tube
Long tube
(
)
Telephone
Check enclosed
(payable to Graco Children’s
Products Inc.)
Short tube
Changing pad
Changing table
Accessory bag
Charge to credit card:
Visa
MasterCard
Discover
Total:
Shipping
& handling:
$5.00
Account #:
6% sales tax
(PA only):
Expiration date:
Signature:
Total amount
due:
361-10-99
17
Download from Www.Somanuals.com. All Manuals Search And Download.
|