INSTALLATION AND
OPERATING INSTRUCTIONS
Read these instructions thoroughly before starting
POWER VENTED WATER HEATER
WARNING:
Improper installation, adjustment, alter-
ation, service, or maintenance can cause
injury or property damage. Refer to this
manual. For assistance or additional infor-
mation, consult a qualified installer, serv-
ice agency, or the gas utility.
FOR YOUR SAFETY
• Do not store or use gasoline or other
flammable vapours and liquids in the
vicinity of this or any other appliance.
• Installation and service must be per-
formed by a qualified installer, service
agency or the gas utility.
WARNING:
If the information in these instructions is
not followed exactly, a fire or explosion
may result causing property damage, per-
sonal injury or death.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do
not use any phone in your building.
• Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier,
call the fire department.
GSW Water Heating is a division of
A. O. Smith Enterprises Ltd.
PART NO. 319594-000 REV. 01 (10-11)
Download from Www.Somanuals.com. All Manuals Search And Download.
This page intentionally left blank. May be used for notes or to record other installation information.
– 3 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance.
Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word
“DANGER” or “WARNING”.
You can be killed or seriously injured if you don’t immediately follow
instructions.
DANGER
WARNING
You can be killed or seriously injured if you don’t follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the
chance of injury, and tell you what can happen if the instructions are not followed.
Examples of qualified service technicians include those
trained in the plumbing and heating industry, local gas utili-
ty personnel or an authorized service person.
I) INTRODUCTION
Thank you for purchasing a Flammable Vapour Ignition
Resistant Power Vented Water Heater. This water heater
is designed to reduce the risk of flammable vapour related
Service to the Power Vent System should only be per-
fires by shutting the burner down before flammable vapours
formed by a qualified service technician.
get into the water heater combustion chamber. This is
achieved by the means of the flammable vapour sensor.
The manufacturer and seller of this water heater will not
Properly installed and maintained, it will provide years of
assume any liability for any property damage, personal
trouble free service.
injury or death resulting from improper sizing, installation or
This gas-fired water heater has been developed to produce
failure to comply with these instructions.
potable hot water for normal residential demands and may
also be used in combination with space heating applica-
The warranty on this water heater is in effect only when the
tions. Any deviation from these applications could affect
water heater is installed and operated in accordance with
your warranty.
these instructions. A data plate identifying your water heater
can be found above the gas control/thermostat. When refer-
ring to your water heater, always have the information listed
on the data plate readily available.
User Responsibilities
This manual has been prepared to acquaint you with the
installation, operation and maintenance of your gas fired
water heater and provide important safety information in
these areas. It is your responsibility to ensure that your
water heater is properly installed and cared for.
Protect your warranty: Regularly service your water
heater as directed in the "Maintenance" section of this man-
ual.
FAILURE TO FOLLOW THE INSTRUCTIONS IN THIS
MANUAL MAY RESULT IN SERIOUS BODILY INJURY
AND/OR PROPERTY DAMAGE. THOROUGHLY READ
AND UNDERSTAND ALL INSTRUCTIONS BEFORE YOU
ATTEMPT TO INSTALL, OPERATE OR MAINTAIN THIS
HEATER.
Retain your original receipt as proof of purchase.
Do not discard this manual. You or future users of this
water heater will need it for reference.
Installation and service requires trade knowledge in the
areas of plumbing, electricity, venting, air supply and gas
supply. If you lack these skills or have difficulty understand-
ing these instructions, you should not proceed. Enlist the
help of a qualified service technician to install this water
heater.
– 4 –
Download from Www.Somanuals.com. All Manuals Search And Download.
lar products, should not be stored or used near the water
heater or air intake. Due to the nature of air movement,
flammable vapours can be carried some distance from the
point of storage. The gas-fired water heater igniter or burn-
er flame can ignite these vapours causing a flashback, fire
or explosion, which may result in severe property damage,
serious personal injury or death. If flammable liquids or
vapours have spilled or leaked in the area of the water
heater, leave the area immediately and call the fire depart-
ment from a neighbor's home. Do not attempt to clean the
spill until all ignition sources have been extinguished.
II) SAFETY
This water heater is design-certified by CSA International as
a Category III, non-direct vented water heater that takes its
combustion air either from the installation area or from air
ducted to the unit from the outside.
In addition to the installation instructions found in this man-
ual, the water heater must be installed in accordance with
all local and provincial or state codes or, in the absence of
such, with the latest editions of the following specifications.
For Installations in Canada:
Safety Warning (Scalding)
"Natural Gas and Propane Installation Code" CAN/CSA-
B149.1 and "Canadian Electrical Code (CAN/CSA
C22.1), Part I" available from:
DANGER
Canadian Standards Association,
5060 Spectrum Way,
Mississauga, Ontario, Canada
L4W 5N6
For Installations in the United States:
"National Fuel Gas Code" ANSI Z223.1 (NFPA 54) and
"National Electrical Code" (NFPA 70)" available from:
American National Standards Institute,
25 West 43rd Street,
New York, NY 10036
Hot water produced by this appliance can cause severe
burns due to scalding. The hazard is increased for young
children, the aged or the disabled when water temperatures
exceed 52°C (125°F). Use tempering valves, also known as
mixing valves, in the hot-water system to reduce the risk of
scalding at point-of-use such as lavatories, sinks and
bathing facilities (see Figure 17). Such precautions must be
followed when this heater is operated in combination with
dishwashing or space heating applications.
Massachusetts code requires this water heater to be
installed in accordance with Massachusetts Plumbing and
Fuel Gas Code 248 CMR Section 2.00 and 5.00.
Check your phone listings for the local authorities having
jurisdiction over your installation.
Safety Warning (Flammable Vapours)
WARNING
Safety Warning (Carbon Monoxide)
DANGER
Carbon Monoxide Warning
• Follow all vent system requirements by
the local authorities having jurisdiction
over your installation.
FLAMMABLES
Flammable Vapours
• Failure to do so can result in death, explo-
sion or carbon monoxide poisoning.
FIRE AND EXPLOSION HAZARD
Can result in serious injury or death
Do not store or use gasoline or other flammable vapours and liquids
in the vicinity of this or any other appliance. Storage of or use of gasoline
or other flammable vapours or liquids in the vicinity of this or any other
appliance can result in serious injury or death.
As with all fuel burning equipment, this heater requires an
adequate supply of air for combustion and ventilation. An
insufficient air supply can result in poor combustion or the
re-circulation of the flue gases. Such a condition can cause
soot build-up and present a fire hazard. Flow reversal of flue
gases can cause an increase of carbon monoxide inside of
the dwelling that could result in serious bodily harm or death
from asphyxiation.
There is a risk of property damage, personal injury or death
from the by-products of combustion (e.g., flue gases), in
using fuel-burning appliances such as water heaters. Areas
that may not be suitable for water heater installation include
those where flammable liquids, gasoline, solvents, adhe-
sives etc. are stored, or where engine-driven equipment or
vehicles are stored, operated or repaired. These, and simi-
MAKE SURE THE FLOW OF COMBUSTION AND VENTI-
LATION AIR IS NOT RESTRICTED.
– 5 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Relief Valve Requirements (T&P)
All water heaters must be fitted with a proper temperature
and pressure relief valve. These valves must be certified as
meeting the requirements of the "Standard For Relief
Valves For Hot Water Supply Systems, ANSI
Z21.22/CSA 4.4".
IMPORTANT:
This water heater must be installed strictly in accordance
with the instructions enclosed, and local electrical, fuel
and building codes. It is possible that plumbing connec-
tions to the water heater, or the water heater itself, may
develop leaks. IT IS THEREFORE IMPERATIVE that the
water heater be installed so that any leakage of the tank
or related water piping is directed to an adequate drain in
such a manner that it cannot damage the building, furni-
ture, floor covering, adjacent areas, lower floors of the
structure or other property subject to water damage. This
is particularly important if the water heater is installed in a
multi-story building, on finished flooring or carpeted sur-
faces. GSW WILL NOT ASSUME ANY LIABILITY for
damage caused by water leaking from the water heater,
pressure relief valve, or related fittings. Select a location
as centralized within the piping system as possible. In any
location selected, it is recommended that a suitable drain
pan be installed under the water heater. This pan must
limit the water level to a MAXIMUM depth of 45mm (1 3/4
in.) and have a diameter that is a minimum of 50mm (2 in.)
greater than the diameter of the water heater. Suitable
piping shall connect the drain pan to a properly operating
floor drain. When used with a fuel-fired heater, this drain
pan must not restrict combustion air flow.
Flooding/Freezing
If this water heater has been exposed to flooding, freezing,
fire or any unusual condition, do not put it into operation until
it has been inspected and approved by a qualified service
technician. THESE CONDITIONS CAN RESULT IN
UNSEEN INTERNAL DAMAGE and are not subject to war-
ranty coverage.
CAUTION
Hydrogen gas can be produced in a hot water system
served by this heater that has not been used for a long
period of time (generally two (2) weeks or more).
Hydrogen gas is extremely flammable and can ignite
when exposed to a spark or flame. To reduce the risk of
injury under these conditions, it is recommended that the
hot water faucet be opened for several minutes at the
kitchen sink before using any electrical appliance con-
nected to the hot water system. Use caution in opening
faucets. If hydrogen is present, there will probably be an
unusual sound such as air escaping through the pipe as
the water begins to flow. There should be no smoking or
open flame near the faucet at the time it is open.
45mm MAX
(1 3/4 in.)
III) INSTALLATION
Unpacking the Water Heater
WARNING
Excessive Weight Hazard
Use two or more people to move and install
water heater. Failure to do so can result in
back or other injury.
AT LEAST 50mm (2 in.)
GREATER THAN THE DIAMETER
OF THE WATER HEATER.
Important: Do not remove any permanent instructions,
labels, or the data label from outside of the water heater or
on the inside of panels.
PIPE TO
ADEQUATE
DRAIN
Figure 1 Drain Pan Installation
Location Requirements
•
•
•
Remove exterior packaging and place installation com-
ponents aside.
Inspect all parts for damage prior to installation and
start-up.
Completely read all instructions before attempting to
assemble and install this product.
The water heater must be installed indoors in an area not
subject to freezing temperatures and in a vertical position
on a level surface. Water heaters located in unconditioned
spaces (e.g., attics, basements etc.) may require insulation
of the water piping, drain piping and venting to protect
against condensation. The power vented series of water
heaters are designed to vent the products of combustion
horizontally through the wall or vertically through the roof.
The blower expels the products of combustion by means of
plastic piping to the outdoors without the need for a con-
ventional chimney.
If you observe damage to the water heater or any of its com-
ponents, DO NOT ASSEMBLE OR INSTALL IT OR MAKE
ANY ATTEMPT TO FIX THE DAMAGED PART(S). Contact
the place of purchase for further instructions.
•
After installation, dispose of packaging material in the
proper manner.
Select a location as centralized within the piping system as
possible. The heater should be located in an area where
leakage of the tank or connections will not result in damage
– 6 –
Download from Www.Somanuals.com. All Manuals Search And Download.
to the area adjacent to the water heater or to lower floors of Figure 2 may be used as a reference guide to locate the
the structure (see "IMPORTANT" notice on the previous specific clearance locations. A minimum of 600mm (24 in.)
page). Before installing this water heater, consideration and of front and top clearance and 100mm (4 in.) on each side
planning must be given to the following details:
should be provided for inspection and service.
•
Proximity to walls and other objects (see "Clearance
and Accessibility").
Access to gas supply (see "Gas Supply").
Routing and support of the vent piping and termination
(see "Venting").
Gas Supply
•
•
DANGER
•
Position of water supply and placement of water piping
and floor drain (see "Water Supply").
In Earthquake Zones
Explosion Hazard
• Use a CSA approved gas supply line.
• Install a gas supply shut-off valve.
• Do not connect a natural gas water heater
to a L.P. gas supply.
• Do not connect a L.P. gas water heater to
a natural gas supply
• Failure to follow these instructions can
result in death, an explosion or carbon
monoxide poisoning.
The water heater must be braced, anchored, or strapped to
avoid moving during an earthquake. Contact local utilities
for code requirements in your area.
Closet Installation & Floor Surfaces
The water heater may be installed in a closet with a door off
a bedroom or bathroom providing the units are installed and
vented per the manufacturer's instructions.
Important: If installing over carpeting, the carpeting must
be protected by a metal or wood panel beneath the water
heater. The protective panel must extend beyond the full
width and depth of the water heater by at least 76mm (3 in.)
in each direction or if in an alcove or closet installation, the
entire floor must be covered by the panel.
Read the data plate to be sure the water heater is made
for the type of gas you will be using in your home. This
information will be found on the data plate located above the
gas control valve. If the information does not agree with the
Clearances and Accessibility
•
The minimum clearances between the heater and com- type of gas available, do not install or attempt to start. Call
bustible materials are:
your dealer.
Top
Front
200mm (8 in.)
100mm (4 in.)
Note: An odourant is added by the gas supplier to the gas
Rear and Sides 25mm (1 in.)
used by this water heater. This odourant may fade over an
Note: These requirements are also listed on the data plate extended period of time. Do not depend upon this odourant
located on the front of the water heater.
as an indication of leaking gas.
•
The water heater is certified for installation on a com-
bustible floor.
CLOSETS
ALCOVES
AIR INTAKE *
GAS
CONTROL/
THERMOSTAT
MANUAL
GAS
SHUT-OFF
BACK
TOP TO
CEILING
VENT
SIDES
GROUND-
JOINT UNION
SIDES
76mm
(3 in.)
VENT
DRIP LEG
SENSOR *
FRONT 600mm
(24 in.) MIN.
FOR SERVICE
* DO NOT BLOCK AIR INTAKE OR SENSOR ACCESS. ENSURE ADEQUATE
CLEARANCE FOR AIR SUPPLY
Figure 2 Minimum Clearance Locations
Figure 3 Gas Piping (typical)
– 7 –
Download from Www.Somanuals.com. All Manuals Search And Download.
This gas piping must be installed in accordance with all local Gas Leak Testing
and provincial or state codes or, in the absence of such, the Important: This water heater and its gas connection must
latest edition of "Natural Gas and Propane Installation be leak tested before placing the appliance in operation.
Code" CAN/CSA-B149.1 (Canada), or "National Fuel Gas
Code" ANSI Z223.1 (NFPA 54) (U.S.A.).
•
If the code requires the gas lines to be tested at a pres-
sure exceeding 14 in. w.c. (3.5 kPa), the water heater
and its manual shut-off valve must be disconnected
from the gas supply piping system and the line capped.
If the gas lines are to be tested at a pressure less than
14 in. w.c. (3.5 kPa), the water heater must be isolated
from the gas supply piping system by closing its manu-
al shut-off valve.
Use properly sized gas piping to ensure full gas input and a
properly sized gas supply regulator to ensure adequate gas
supply pressure. The supply piping and regulator must be
large enough to satisfy the requirements of all appliances
connected to the gas service when all appliances are oper-
ating simultaneously. Undersized piping and insufficient
•
pressure can restrict the gas flow causing the water heater Gas Operating Pressures
to perform poorly. Improperly sized piping may pose a safe- The gas supply pressure and burner manifold pressure is
ty hazard.
listed on the data plate located on the front of the heater
above the gas control/thermostat. Ensure the gas supply
Note: When installing gas piping, apply sealing compounds pressure to the water heater and the burner manifold pres-
approved for use with natural and propane gas.
sure are properly adjusted while all appliances are in oper-
1. Install a readily accessible manual shut-off valve in the ation. Refer to Figure 22 (Robertshaw) or Figure 24 (White-
gas supply line as recommended by the local utility. The Rodgers) for Gas Control/Thermostat Details.
owner/operator must be shown the location of this valve
and be given instructions on how to use it to shut off the U.L.and CSA recognized fuel gas and Carbon Monoxide
gas to the heater.
(CO) detectors are recommended in all applications and
2. Install a drip leg (if not already incorporated as part of should be installed using the manufacturer's instructions
the water heater) as shown. The drip leg must be no and local codes, rules or regulations.
less than 76mm (3 in.) long for the accumulation of dirt,
foreign material, and water droplets.
3. Install a ground joint union, or other approved gas dis-
connect, between the gas control/thermostat and the
manual shut-off valve. This is to allow easy removal of
the gas control/thermostat.
4. Turn the gas supply on and check for leaks. Use a chlo-
ride-free soap and water solution (bubbles forming indi-
cate a leak) or other approved method.
WARNING
Exposure to a higher gas supply pressure
may cause damage to the control, resulting
in explosion or fire. Consult your local gas
supplier and gas authorities. DO NOT PUT
INTO SERVICE IF OVER-PRESSURIZATION
HAS OCCURRED.
Gas Supply Pressure
Important: The gas supply pressure must not exceed the
maximum supply pressure as stated on the water heater's
data plate.
Gas line purging
Air may be present in the gas lines and could prevent the
burner from lighting on initial start-up. The gas lines should
be purged of air by a qualified service technician after instal-
lation of the gas piping system.
– 8 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The top opening shall not be lower than the top of the
heater. The location of the bottom opening shall be 150-
450mm (6-18 in.) above floor level.
Air Requirements
Important: Air for combustion and ventilation must not
come from a corrosive atmosphere. Any failure due to cor-
rosive elements in the atmosphere is excluded from war-
ranty coverage.
Note: Ensure sufficient ventilation air to prevent elevat-
ed temperatures in closets and ventilated spaces.
When an exhaust fan is installed in the same room as the
water heater, the supply air openings must be of sufficient
capacity to prevent a backflow of air through the water
heater exhaust venting.
Installations in or for certain places including, but not limited
to, those listed below may require outdoor air for combus-
tion to reduce the risk of chemical exposure:
•
•
•
•
Beauty shops, Photo processing labs
Buildings with indoor pools
Water heaters installed in laundry, hobby or craft rooms
Water heaters installed near chemical storage areas
b). When using a single air supply, the duct shall terminate
within 300mm (12 in.) above and within 600mm (24 in.)
horizontally of the burner level of the appliance having
the largest input.
In such circumstances, outdoor combustion air may reduce,
but will not eliminate the presence of corrosive chemicals in
the air. Combustion air must be free of acid-forming chemi-
cals such as sulfur, fluorine and chlorine. These elements
are found in aerosol sprays, detergents, bleaches, cleaning
solvents, air fresheners, paint and varnish removers, refrig-
erants and many other commercial and household prod-
ucts. When burned, vapours from these products form high-
ly corrosive acid compounds. These products should not be
stored or used near the water heater or air inlet.
Refer to latest edition of the "Natural Gas and Propane
Installation Codes" CAN/CSA-B149-1 for air supply duct
sizes.
The area in which the heater is located is classified as either
"an unconfined space" or "a ventilated space."
An unconfined space is defined as a space having a vol-
ume not less than 50 cubic feet per 1000 BTU/hour (4.8
cubic metres per kilowatt) of combined input rating of all
appliances using the space. Adjacent open rooms may be
included as part of the unconfined space, provided there
are no closeable doors between these rooms. An exam-
ple of this is an open basement.
A ventilated space is one smaller than described above.
For buildings using tight construction (newer and renovated
structures), the air supply shall be introduced from the out-
doors, regardless of whether the space is confined or
unconfined. CHECK LOCAL CODES.
(a)
PERMANENT
OPENINGS
Ventilated Space Air Requirements for
VENTILATED
Canadian Installations
UNCONFINED
SPACE
SPACE
Refer to Figure 4 (a), or (b), for proper sizing and location of
combustion air ducts and openings. CHECK LOCAL
CODES.
a). Two permanent openings shall be provided connecting
to ventilated space (e.g. closet, small room) with the
unconfined space. Each opening shall be equal or
greater than 645cm2 (100 in2.) with a width to height
ratio of 2:1. The top opening shall be located close to
the ceiling.
EQUIPMENT LOCATED IN VENTILATED
SPACES; ALL AIR FROM INSIDE THE BUILDING.
300mm
(12 in.)
(MIN)
VENTILATED
SPACE
(b)
GRADE
COMBINATION
COMBUSTION/
VENTILATION
AIR DUCT
600mm (24 in.)
300mm (12 in.)
BASEMENT INSTALLATION, EQUIPMENT LOCATED
IN VENTILATED SPACES; ALL AIR FROM OUTDOORS
Figure 4 Combustion Air Supply Openings And Ducts
Figure 4a Air Opening Locations
(Can.)
– 9 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Ventilated Space Air Requirements for
U.S. Installations
(a)
Refer to Figure 5 (a), (b), (c) or (d) for proper sizing and
location of combustion air ducts and openings. CHECK
LOCAL CODES.
PERMANENT
OPENINGS
a) Equipment located in ventilated spaces; all air from
inside the building.
VENTILATED
SPACE
UNCONFINED
SPACE
Two permanent openings shall be provided connecting
to ventilated space (e.g. closet, small room) with the
unconfined space. Each opening shall be equal or
greater than 645cm2 (100 in2.) with a width to height
ratio of 2:1. The top opening shall be located close to
the ceiling.
EQUIPMENT LOCATED IN VENTILATED
SPACES; ALL AIR FROM INSIDE THE BUILDING.
PERMANENT
300mm VENTILATION
VENTILATED
(b)
COMBUSTION
AIR DUCT
Note: The opening shall not be lower than the top of the
heater. The location of the bottom opening shall be 150-
450mm (6-18 in.) above floor level.
SPACE
(12 in.)
AIR.
300mm
(12 in.)
ABOVE
GRADE
OR
b) Basement installation, equipment located in ventilated
spaces; all air from outdoors.
SNOW
LINE
Refer to the latest edition of the "National Fuel Gas
Code" ANSI Z223.1 for air supply duct sizes and
restrictions.
GRADE
c) Equipment located in ventilated spaces; all air from out-
doors.
BASEMENT INSTALLATION, EQUIPMENT LOCATED
IN VENTILATED SPACES; ALL AIR FROM OUTDOORS
300mm
(12 in.)
Refer to the latest edition of the "National Fuel Gas
Code" ANSI Z223.1 for air supply duct sizes and
restrictions.
OUTDOORS
AIR DUCT
(c)
d) Equipment located in ventilated spaces; all air from out-
doors through ventilated attic.
300mm (12 in.)
Refer to the latest edition of the "National Fuel Gas
Code" ANSI Z223.1 for air supply duct sizes and
restrictions.
VENTILATION
COMBUSTION
VENTILATED
SPACE
Note: Ensure sufficient ventilation air to prevent elevat-
ed temperatures in closets and ventilated spaces.
When an exhaust fan is installed in the same room as the
water heater, the supply air openings must be of sufficient
capacity to prevent a backflow of air through the water
heater exhaust venting.
EQUIPMENT LOCATED IN VENTILATED
SPACES; ALL AIR FROM OUTDOORS.
300mm (12 in.)
ATTIC LOUVERS TO OUTDOORS
(d)
OUTLET
AIR
INLET AIR
DUCT
VENTILATED
SPACE
Burn Hazard
300mm (12 in.)
EQUIPMENT LOCATED IN VENTILATED SPACES; ALL
AIR FROM OUTDOORS THROUGH VENTILATED ATTIC.
Do not touch vent.
Doing so can result in
burns.
Figure 5 Combustion Air Supply Openings And Ducts
(U.S.A.)
– 10 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Notes and Warnings
Exhaust Venting
•
This heater is certified to be installed using Schedule 40
PVC or CPVC plastic vent material. In Canada some
jurisdictions require that this material is approved to
ULC S636. ULC S636 mandates that components from
different systems must not be mixed in the same vent
runs. Check local codes to determine which materials
are allowed in your area and only use approved materi-
al. All venting material and components must be joined
with the approved primer/cleaner and solvent cement.
Do not common vent this heater with any other appli-
ance.
This heater is designed to exhaust the products of combus-
tion (flue gases) to the outdoors using a sealed piping sys-
tem. Table 2 lists the allowable vent materials and sizing
information. Figure 8 shows the general venting layout while
Figures 9-11 show various end termination details and
clearances. Connection of the venting piping to the blower
is shown in Figures 13-15.
Correct installation of the venting system is essential to the
safe and efficient operation of this water heater. Vent piping
must be installed in accordance with all applicable local and
provincial or state codes. In the absence of such codes, all
installation shall meet the requirements as stated in the lat-
est edition of the "Natural Gas and Propane Installation
Codes" CAN/CSA-B149-1 (Canada) or "National Fuel
Gas Code" ANSI Z223.1 (NFPA 54) (U.S.A.).
•
•
During operation the plastic piping will expand as it
heats up and contract as it cools down. This is normal
for this type of venting. Rigidly fastening the vent piping
can cause undue stress that may result in the cracking
or fracturing the vent piping material. A fracture of the
venting pipe poses a serious safety hazard. To prevent
stressing of the vent system, all hangers and supports
must allow the vent piping freedom to move.
NOT RECOMMENDED:
PREFERRED PRACTICE:
•
•
Use long sweep elbows wherever possible. Closely-
coupled elbows and short radius elbows can reduce the
venting capacity.
All power vented water heaters generate a certain
amount of operational noise. In order to minimize noise
transmission to the support structure, use isolation pads
between the pipe hangers and the vent pipe.
STREET ELBOW
NORMAL ELBOW
•
Most power vent installations develop some condensa-
tion in the vent piping. When using long runs of venting
or when the venting passes through cold or unheated
areas, considerable amounts of condensate from the
flue gases can develop. Provision must be made for the
condensate to drain freely from the system or to be col-
lected in a condensate trap(s) that can be drained.
Damage or fracture of the vent piping may occur if the
condensate is allowed to collect and freeze. Pooling of
condensate can restrict airflow and can cause nuisance
failures of the system.
150mm
(6 in.) min.
BACK TO BACK ELBOWS
•
•
Be aware of any concealed wiring or piping inside the
walls.
Ensure sufficient ventilation air to prevent elevated tem-
peratures in closets and ventilated spaces.
90° SHORT SWEEP ELBOW
(MORE RESTRICTIVE)
90° LONG SWEEP ELBOW
(LESS RESTRICTIVE)
Figure 6 Pipe Fittings And Practices
Note: The information provided in Figure 6 is intended as a
guideline for good vent installation practices only and is not
intended to restrict venting options beyond those restric-
tions established by the latest edition of the "Natural Gas
and Propane Installation Codes" CAN/CSA-B149-1 or
any applicable local and provincial codes.
VENT LENGTH LESS THAN OR
EQUAL TO 6.1 EQUIVALENT METRES
(20 FT.) USE THIS SCREEN.
VENT LENGTH GREATER THAN 6.1
EQUIVALENT METRES (20 FT.) USE
THIS SCREEN.
Figure 7 Rodent Screens
– 11 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Venting terminations and sizing
shown in Figure 8. The appropriate screen is to be
installed into the end of the termination elbow and
secured with a small amount of silicone sealant. This
will allow for easy removal for inspection and cleaning.
For installations using 76mm (3 in.) venting, use the
76mm (3 in.) termination elbow and screen (not sup-
plied).
•
Refer to Figure 8 and Table 2 for vent pipe materials
and sizing. Examples of the vent terminations are
shown in Figures 9 and 10. If the installation requires a
vent riser, suitable drainage must be provided to ensure
condensation does not accumulate. Termination
through a roof is shown Figure 11.
•
G/JW 40, 50 and 60-gallon heaters are supplied with a
50mm (2 in.) termination elbow and (2) plastic "rodent
screens" (see Figure.7). The screen is required to keep
foreign objects, rodents and small birds from entering
the venting system and only one (1) screen is to be
installed in the termination elbow. These screens have
been sized to ensure maximum energy efficiency of the
venting system based on the "equivalent length" of the
vent piping. How to determine the equivalent length is
•
G/JW5065 high input models are supplied with a 76mm
(3 in.) termination elbow that includes a steel mesh
rodent screen.
WATER
HEATER SUFFIX
MODEL
* VENT
MATERIAL
(SCHEDULE 40)
VENT PIPE
SIZE
MAXIMUM EQUIVALENT
VENT LENGTH
MINIMUM EQUIVALENT
VENT LENGTH
NVH,
PVH
0.76m (2.5 ft.) + one 90° elbow +
termination elbow
50mm (2 in.) PVC**, CPVC 12.3m (40 ft.) + termination elbow
G/JW40,
50, 60
NVH,
PVH
76mm (3 in.) PVC**, CPVC 24.4m (80 ft.) + termination elbow 12.3m (40 ft.) + termination elbow
SNV,
SPV
0.91m (3 ft.) + one 90° elbow +
termination elbow
G/JW5065
76mm (3 in.)
PVC, CPVC
PVC, CPVC
12.3m (40 ft.) + termination elbow
G/JW5065 LNV 76mm (3 in.)
19.8m (65 ft.) + termination elbow 6.9m (20 ft.) + termination elbow
Equivalent lengths of straight pipe for various elbows using
Schedule 40 PVC and CPVC.
Notes:
1. Use long radius elbows where possible. Minimum dis-
tance between 90º elbows should be 150mm (6 in.).
2. *Check local codes to determine which materials are
allowed in your area.
3. **Pipe assembly adapter must be used with PVC
venting material (see Figures 13, 14 & 15).
Short Sweep/ Long Sweep/
Size
Type
Short Radius
Long Radius
1.52m (5 ft.)
1.52m (5 ft.)
50mm (2 in.) 90° elbow 2.44m (8 ft.)
76mm (3 in.) 90° elbow 2.44m (8 ft.)
50mm (2 in.) 45° elbow 0.91m (3 ft.) 0.76m (2.5 ft.)
76mm (3 in.) 45° elbow 1.22m (4 ft.) 1.07m (3.5 ft.)
Table 2 Allowable Vent Lengths and Materials (Vert. and Horiz.).
NOTE: VENT PIPE MUST BE SUPPORTED EVERY 1.2m (4 ft.). TO PREVENT VIBRATION, USE ISOLATION
PADS WHEN ATTACHING STRAPS TO FLOOR JOISTS, WALLS OR CEILINGS.
TERMINATION
ELBOW
45°
ELBOW
90°
ELBOW
STRAP
RODENT SCREEN
(INSTALL INTO
ELBOW)
Example for calculating equivalent feet.
Section “A” . . . . 0.15m . . (0.5 ft.)
90° elbow . . . . . 1.83m . . (6.0 ft.)
Section B . . . . . 0.31m . . (1.0 ft.)
45° elbow . . . . . 0.91m . . (3.0 ft.)
Section C . . . . . 0.46m . . (1.5 ft.)
45° elbow . . . . . 0.91m . . (3.0 ft.)
Section D . . . . . 4.57m . (15.0 ft.)
Total Equivalent 9.14m . (30.0 ft.)
PVC ADAPTER
(SUPPLIED)
150mm
(6 in.)
MIN.
GROUND LEVEL OR
MAXIMUM SNOW
LINE*
Based on this example use the (fully open) rodent
screen for vent length greater than 6.1 equivalent
metres (20 equivalent ft.) (see Figure 7).
Figure 8 General Venting Layout
– 12 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Venting instructions
10. Insert the vent piping through this hole and secure into
position. Connect the vent pipe to the end termination
elbow as shown in Figures.9-11.
1. Plan the venting layout starting at the vent termination
and work back toward the heater. Take into considera-
tion the style and position of the vent termination, the
vent pipe routing, elbows and connectors required and
the necessary support hangers.
2. G/JW 40, 50 and 60-gallon heaters may use 50mm (2
in.) or 76mm (3 in.) venting depending on "Equivalent
Vent Length" as described in Table 2. G/JW5065 high
input models require 76mm (3 in.) venting. See also the
section on "Vent pipe connection to blower".
SEALANT
ATTACH 90°
TERMINATION
3. Venting should be as direct as possible with the fewest
number of fittings. Use long radius 45 degree and long
radius 90 degree elbows wherever possible.
4. Do not use 90 degree elbows "back to back" (other than
termination installations) and do not use street elbows.
Maintain a minimum 150mm (6 in.) straight section
between elbows. Closely coupled and short radius
elbows reduce the venting capacity (see Figure 6 and
the note below it).
ELBOW
VENT PIPING MAY BE
SLOPED
IN
ANY
RODENT SCREEN
(INSTALL INTO
ELBOW)
DIRECTION, AS LONG
AS A WATER TRAP IS
NOT CREATED IN
THE VENTING SYS-
TEM. THE SLOPE
SHOULD BE KEPT TO
300mm
(12 in.)
MIN.
SEALANT
GROUND LEVEL
OR MAXIMUM
SNOW LINE*
A
MINIMUM SO AS
NOT TO EXERT ANY
UNDUE STRESS ON
THE PIPE.
5. DO NOT USE AN ELBOW AS A SUPPORT POINT.
Elbows are not designed to carry the weight of the vent-
ing system.
* WHERE SNOW COVER IS NORMAL DURING WINTER, ENSURE
SUFFICIENT VENT CLEARANCE TO PREVENT BLOCKAGE OR ICE BUILDUP.
Figure 9 Vent Termination Exterior Installation
6. Calculate "Equivalent Vent Length" before starting. Do
not exceed the values shown in Table 2. An example of
how this length is determined is shown in Figure 8. The
value from your calculations should also be used to
determine which rodent screen to install into the vent
termination elbow.
ATTACH 90°
TERMINATION
ELBOW
BRACKET
EQUIVALENT
VENT LENGTH
MEASURED FROM
THIS POSITION
RODENT
SCREEN
(INSTALL
INTO
7. Measure the vent piping and cut to required lengths.
Pipes must be cut at right angles and deburred to
ensure a good smooth fit with sufficient overlap for the
glue joints. Correct any interference conditions.
8. Provide support hangers for horizontal vent piping every
1.2m (4 ft.) to prevent sagging and stress. Provide a
minimum of 3mm (1/8 in.) rise per 1.2m (4 ft.) of vent
piping to ensure adequate drainage. Horizontal vent
piping must not sag to form valleys where condensate
may collect. Vertical venting shall be supported every
1.5m (5 ft.). Use appropriate support straps and vibra-
tion isolators (foam pads) on straight sections only. Do
not use elbows as support points. Allow sufficient clear-
ance for expansion and contraction of the venting sys-
tem.
ELBOW)
SEALANT
300mm
(12 in.)
MIN.
VENT
RISER
GROUND LEVEL
OR MAXIMUM
SNOW LINE*
VENT PIPING TO BE
SLOPED (DOWN)
TOWARD HEATER TO
PREVENT WATER
FROM COLLECTING.
SEALANT
* WHERE SNOW COVER IS NORMAL DURING WINTER, ENSURE
SUFFICIENT VENT CLEARANCE TO PREVENT BLOCKAGE OR ICE BUILDUP.
Figure 10 Installation Of Fabricated Vent Riser.
76mm (3 in.)
MIN. LENGTH
TERMINATION
MAY BE 90°
ELBOW
9. At the point where the vent pipe exits the building, cut a
65mm (2-1/2 in.) hole for 50mm (2 in.) venting or a
90mm (3-1/2 in.) hole for 76mm (3 in.) venting.
A VENT USED IN A SPECIAL
RODENT
CAUTION:
VENTING SYSTEM WITH
POSITIVE VENT PRESSURE
AND PASSING THROUGH A
ROOF SHALL EXTEND AT
LEAST 450mm (18 in.)
SCREEN
(INSTALL
INTO
450mm
(18 in.)
Use of Solvent Cement and Primer
• Use only in well-ventilated areas.
• Do not use near flame or open fire.
• Use only the Solvent Cement and Primer
appropriate for the venting material being
used.
ELBOW)
ABOVE
THE
HIGHEST
POINT WHERE IT PASSES
THROUGH THE ROOF SUR-
FACE AND ANY OTHER
ROOF
LINE
OBSTRUCTION WITHIN
A
HORIZONTAL DISTANCE OF
450mm (18 in.). A VERTICAL
VENTING SYSTEM MUST
BE SUPPORTED EVERY
1.5m (5 ft.).
• Solvent cements for plastic pipe are flam-
mable liquids and must be kept away from
all sources of ignition.
Figure 11 Vertical Venting
– 13 –
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Dry fit all vent pipes, elbows, connectors and fittings 6. Loosen the upper clamp on the rubber coupling and
before joining any parts with solvent cement. PARTS
MUST FIT WITHOUT STRESS OR BENDING OF ANY
SECTION and each connection must overlap a mini-
mum of 13mm (1/2 in.). Do not force fit any of the con-
nections. Use only the appropriate solvent cement.
insert the sanded end of the CPVC vent pipe or the
PVC transition coupler a full 32mm (1-1/4 in.). Do not
use glue or sealant in the rubber coupling. Check that
there is no stress on the connection or the vent pipe that
may be caused by twisting or bending.
Caution: Solvent cements may produce flammable vapours. * These parts are available from your water heater supplier.
Use only in well-ventilated areas and keep away from all 7. Tighten the upper clamp so that the vent pipe is firmly
sources of ignition.
secured in the coupling and is gas tight. Do not over
tighten or cause distortion of any of the parts. Ensure
that the bottom of the rubber coupling is firmly seated
on the blower outlet and that the lower gear clamp is
also secure. Check to ensure that there is no distortion
or movement of the clamped assembly once it is com-
pleted.
12. For 50mm (2 in.) venting, install the properly sized
rodent screen into the 50mm (2 in.) outlet elbow and
secure with a small quantity of silicone sealant.
13. Outlet elbows for 76mm (3in) are installed with a metal
rodent screen.
14. Do not seal the vent piping to the wall until the venting
is properly connected to the blower assembly.
8. Complete the venting installation by sealing around the
termination assembly where it passes through the out-
side wall, inside and out, with silicone or other suitable
sealant.
Vent pipe connection to blower
1. The plastic vent piping connects into the rubber cou-
pling located on the top of the blower assembly. This
coupling includes gear clamps to connect the venting to
the blower. These connections must be properly seated
and tightened to prevent the leakage of flue gases into
the area. See Figures 15 & 15a.
2. All G/JW 40, 50 and 60 gallon models, except hi-input
5065 models, are assembled with a 76mm (3 in.) to
50mm (2 in.) transition coupler that must be used for
installations using 2 in. PVC or CPVC vent pipe.
3. For G/JW 40, 50 and 60 gallon installations using 76mm
(3 in.) PVC or CPVC vent pipe, remove the 76mm (3 in.)
to 50mm (2 in.) transition coupler from the rubber cou-
pling and connect the vent pipe directly to the rubber
coupling. See Figure 15a.
4. G/JW5065 hi input models are supplied with a 76mm (3
in.) rubber coupling and are designed to accept PVC or
CPVC vent pipe directly, as shown in Figure 15.
5. Clean and lightly sand the end of the CPVC plastic vent
pipe or PVC transition coupler that will connect into the
rubber coupling.
CAUTION:
• Do Not Overtighten The Top And Bottom
Gear Clamps Of The Rubber Coupling.
• Do Not Apply Solvent Cement Or Silicone
To The Rubber Coupling Connection.
VENT PIPE
50mm (2 in.)
VENT PIPE
76mm (3 in.)
150mm (6 in.)
150mm (6 in.)
MIN. TO 1ST
ELBOW
MIN. TO 1ST
ELBOW
NON HI-INPUT MODEL
HEATERS. BLOWER ASS’Y
WITH RUBBER COUPLING
AND TRANSITION COU-
PLER FOR 50mm (2 in.)
NOMINAL CPVC OR PVC
VENT PIPE.
HI-INPUT MODEL 5065
HEATERS. BLOWER ASS’Y
WITH RUBBER COUPLING
FOR 76mm (3 in.) NOMINAL
CPVC OR PVC VENT PIPE.
RUBBER
COUPLING
TRANSITION
COUPLER
RUBBER
COUPLING
Figure 15a
Blower, Fittings and Vent Pipe Options
Figure 15 Blower, Fittings and Vent Pipe Options
– 14 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Filling the Water Heater
Water Supply
Do not insert the power cord into the electrical receptacle
until all the following steps have been completed.
1. Make sure the drain valve is closed.
Piping Installation
Piping, fittings, and valves should be installed according to
the installation drawing (Figure 16). A pressure-reducing
valve and/or an expansion tank may be required for instal-
lations where the water pressure is high. The pressure-
reducing valve should be located on the supply to the entire
house in order to maintain equal hot and cold water pres-
sure.
2. Open all hot-water faucets served by the system to
allow air to escape from the tank.
3. Open the cold-water inlet valve.
Note: When filling, avoid water leakage. Do not allow the
insulation of the water heater to get wet as water can reduce
the effectiveness of the insulation.
Important:
4. When an uninterrupted stream of water, without appar-
ent air bubbles, flows from the open hot-water faucets,
the tank is full.
5. Close the hot-water faucets and check the system for
leaks. Repair as required and retest.
•
Do not apply heat to the water fittings on the heater as
they may contain nonmetallic parts. If solder connec-
tions are used, solder the pipe to an adapter before
attaching the adapter to the hot and cold water fittings.
Some models may contain energy saving heat traps to
prevent the circulation of hot water within the pipes. Do
not remove the inserts within the heat traps.
•
•
Please note the following:
The system should be installed only with piping that is suit-
able for potable (drinkable) water such as copper, CPVC,
PEX or polybutylene. DO NOT use PVC water piping.
DO NOT use any pumps, valves, or fittings that are not
compatible with potable water.
DO NOT use valves that may cause excessive restriction to
water flow. Use full flow ball or gate valves only.
DO NOT use any lead based solder in potable water lines.
Use appropriate tin-antimony or other equivalent material.
DO NOT tamper with the gas control/thermostat, igniter,
flammable vapour sensor or temperature and pressure
relief valve. Tampering voids all warranties. Only qualified
service technicians should service these components.
DO NOT use with piping that has been treated with chro-
mates, boiler seal, or other chemicals.
Always use a proper grade of joint compound and be
certain that all fittings are drawn up tight.
1. Install the water piping and fittings as shown in Figure
16. Connect the cold water supply to the fitting (3/4"
NPT) marked "COLD" (or "C"). Connect the hot water
supply to the fitting (3/4" NPT) marked "HOT" (or "H").
2. The installation of unions in both the hot and cold water
supply lines is recommended.
3. The manufacturer of this water heater recommends
installing a tempering valve in the domestic hot-water
line as shown in Figure 17. These valves reduce the
point-of-use water temperature by mixing cold and hot
water. Contact a licensed plumber or the local plumbing
authority.
4. If installing the water heater in a closed water system,
install an expansion tank in the cold water line as spec-
ified under "Closed System/Thermal Expansion".
5. Install a shut-off valve in the cold-water inlet line. It
should be located close to the water heater and be eas-
ily accessible. The owner/operator must be shown the
location of this valve and be given instructions on how
to use it to shut off the water to the heater.
DO NOT add any chemicals to the system piping which will
contaminate the potable water supply.
IN A CLOSED SYSTEM USE EITHER: 1.THERMAL EXPANSION TANK
OR
2.PRESSURE RELIEF VALVE.
HOT
WATER
NOTE: BLOWER
OUTLET
ASSEMBLY NOT
SHOWN FOR
CLARITY.
PRESSURE
REDUCING
VALVE
UNION
WITH
BYPASS
COLD WATER
INLET VALVE
COLD WATER
INLET
TEMPERATURE AND
PRESSURE RELIEF VALVE
DISCHARGE LINE 300mm
(12 in.) max (CANADA) OR
150mm (6 in.) max (U.S.)
ABOVE DRAIN
MASSACHUSETTS: INSTALL A
VACUUM RELIEF IN COLD WATER
LINE PER SECTION 19MGL 142
DRAIN PAN CONNECT TO
PROPERLY OPERATING
FLOOR DRAIN.
Figure 16 Water Piping Installation
– 15 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Important: Only a new temperature and pressure relief
valve should be used with your water heater. Do not use an
old or existing valve, as it may be damaged or not adequate
for the working pressure of the new water heater. Do not
place any valve between the relief valve and the tank.
FOLLOW THE
TEMPERING
VALVE MANU-
FACTURER'S
INSTRUCTIONS
TEMPERED
WATER TO
FIXTURE
TER
A
COLD W
WARNING
T&P VALVE
AND DIS-
CHARGE
LINE
TEMPERING
VALVE (SET
TO 49°C
HOT
WATER
OUTLET
(120°F))
Explosion Hazard
• If the temperature and pressure relief
valve is dripping or leaking, have a
licensed plumber repair it.
COLD
WATER
INLET
• Do not plug valve.
• Do not remove valve.
• Failure to follow these instructions can
result in death or an explosion.
Figure 17 Tempering Valve Installation
Closed System/Thermal Expansion
The Temperature and Pressure Relief Valve:
Periodic discharge of the temperature and pressure relief
valve may be due to thermal expansion in a closed water
supply system. The water utility supply meter may contain a
check valve, backflow preventer or water pressure-reducing
valve. This will create a closed water system. During the
heating cycle of the water heater, the water expands caus-
ing pressure inside the water heater to increase. This may
cause the temperature and pressure relief valve to dis-
charge small quantities of hot water. To prevent this, it is
recommended that a diaphragm-type expansion tank (suit-
able for potable water) be installed on the cold water supply
line. The expansion tank must have a minimum capacity of
5.6 litres (1.5 US gallons) for every 190 litres (50 US gal-
lons) of stored water and be rated at the working pressure
of the water heater. Contact the local water supplier or
plumbing inspector for information on other methods to con-
trol this situation.
•
•
•
Must not be in contact with any electrical part.
Must be connected to an adequate discharge line.
Must not be rated higher than the working pressure
shown on the data plate of the water heater.
The Discharge Line/Driptube:
•
Must not be smaller than the pipe size of the relief valve
or have any reducing coupling installed in the discharge
line.
•
Must not be capped, blocked, plugged or contain any
valve between the relief valve and the end of the dis-
charge line.
•
•
•
Must terminate a maximum of 300mm (12 in.) (Canada)
or 150mm (6 in.) (U.S.A.) above the floor.
Must be capable of withstanding 121°C (250°F) without
distortion.
Must be installed to allow complete drainage of both the
valve and discharge line.
Important: Do not plug or remove the temperature and
pressure relief valve.
Temperature and Pressure (T&P) Relief
Valve
For protection against excessive pressures and tempera-
tures, a temperature and pressure relief valve must be
installed in the opening marked "T&P RELIEF VALVE" (see
Figure 18). This valve must be design certified by a nation-
ally recognized testing laboratory that maintains periodic
inspection of the production of listed equipment or materials
as meeting the requirements of the "Standard For Relief
Valves For Hot Water Supply Systems", ANSI
Z21.22/CSA 4.4. The function of the temperature and pres-
sure relief valve is to discharge water in large quantities in
the event of excessive temperature or pressure developing
in the water heater. The valve's relief pressure must not
exceed the working pressure of the water heater as stated
on the data plate.
TEMPERATURE AND
PRESSURE RELIEF
VALVE
DISCHARGE LINE 19mm (3/4 in.)
MIN. DO NOT CAP OR PLUG.
DRAIN PAN. CONNECT TO
PROPERLY OPERATING
FLOOR DRAIN.
Figure 18 Temperature
Installation
&
Pressure Relief Valve
– 16 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Supply
WARNING
Electrical Shock Hazard
• Disconnect power before
servicing.
• Replace all parts and panels
before operating.
• Failure to do so can result in
death or electrical shock.
Important: The electrical controls used inside the gas con-
trol/thermostat of this water heater are polarity sensitive.
Ensure the electrical supply is connected correctly in the
receptacle box. Failure to connect correctly will prevent the
unit from functioning properly (see Figures 19 & 20). Before
performing any electrical service work, label all wires to
avoid connection errors. If wiring has to be replaced, use
only TYPE TEW 105°C wire, (except igniter wires). If there
is a problem with igniter wires, replace igniter assembly in
its entirety. In locations where a sump pump failure, flooding
or exposure to water may be present, a ground fault recep-
tacle is recommended.
Important: Do not use an extension cord to connect the
water heater to an electrical outlet.
•
Ensure that the water heater and the outlet are proper-
ly grounded. Failure to properly ground the heater can
prevent the unit from operating.
Figure 19 Wiring Diagram - Robertshaw Control
•
Ensure that the water heater is installed in accordance
with prevailing provisions of local codes, or, in the
absence of such, the latest edition of "Canadian
Electrical Code (CAN/CSA C22.1), Part I" (Canada) or
"National Electrical Code" (NFPA 70) (U.S.A.).
Before applying power to the water heater, always make
sure:
•
•
•
The voltage and frequency correspond to that specified
on the water heater wiring diagram.
The electrical outlet has the proper overload fuse or
breaker protection.
Fill the tank with water and check all connections for
leaks. Open the nearest hot-water faucet and let it run
for 3 minutes to purge the water lines of air and sedi-
ment and to ensure complete filling of the tank. The
electrical power may then be turned on. Verify proper
operation after servicing.
Note: Always reference the wiring diagram for the correct
electrical connections.
WARNING
When the unit is plugged in, 120VAC is pres-
ent at the electric connections of the gas
control/thermostat.
Figure 20 Wiring Diagram - White-Rodgers Control
– 17 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Flammable Vapour Sensor
* ROTATE LEFT (CCW)
TO REMOVE
When using a gas fired water heater there is a risk of flam-
mable vapours entering the combustion chamber, being
ignited by the burner flame and causing a flashback. In
order to detect such flammable vapours before they enter
the combustion chamber, this water heater is equipped with
a flammable vapour sensor (FVS). It is a chemical-absorp-
tion based sensor that is connected to the gas control/ther-
mostat (see Figures 22 & 24). When exposed to flammable
vapours it will trigger the control to stop the flow of gas and
enter the FVS lockout state. While in the FVS lockout state
the LED on the control will flash the gas lockout code.
(Refer to the “System Error Codes” section of this manual
for an explanation of the codes applicable to the control
installed on your water heater.) If this error occurs, check
around the water heater for sources of chemical contamina-
tion such as: flammable vapours including gas vapours, sol-
vents, paint and thinners as well as sources of water and
detergents. Remove any such sources, check the sur-
SCREW
COVER*
MOUNTING
BRACKET
FLAMMABLE
VAPOUR SENSOR
(PULL TO REMOVE)
Figure 21 Flammable Vapour Sensor (exploded view)
INLET
PRESSURE
PORT
3/4” NPT. WRAP
GAS CONTROL
WITH TEFLON TAPE
SWITCH (ON)
(2 WRAPS MIN.)
MANIFOLD
PRESSURE
ADJUSTMENT
(REMOVE
DIAL FOR
ACCESS)
GAS VALVE
SOLENOID
CONNECTOR
FLAMMABLE VAPOUR
160F MAX. DIAL
SENSOR 2 PIN
MOLEX CONNECTOR
OUTLET
PRESSURE
PORT
QUICK CONNECTS
FOR POWER SUPPLY
AND IGNITER
GAS INLET
1/2” NPT
(UNDER)
TERMINAL BLOCK BLOWER
AND JUNCTION BLOCK 8
PIN MOLEX CONNECTOR
SYSTEM
STATUS
CODES
LED INDICATOR
140F MAX. DIAL
OUTLET TO MANIFOLD
DOOR ASS’Y (UNDER)
GROUND CONNECTION
GAS CONTROL-VIEW OF ELECTRICAL
CONNECTORS, WITH COVER REMOVED
GAS CONTROL-VIEW FROM GAS INLET
WITH TEMPERATURE DIAL REMOVED
FLAMMABLE
VAPOUR
SENSOR
IGNITER
BLOWER
FLAME
SENSOR
CONNECTOR
GAS VALVE
SOLENOID
AIR PRESSURE
SWITCH
GND
HIGH LIMIT
SWITCH
L1
N
POLARITY SENSITIVE DO NOT MIS-
MATCH WIRING. FAILURE TO CONNECT
CORRECTLY WILL PREVENT THE UNIT
FROM FUNCTIONING PROPERLY.
Figure 22 Gas Control/Thermostat Details and Wiring Diagram (Robertshaw)
– 18 –
Download from Www.Somanuals.com. All Manuals Search And Download.
rounding area for damage and call a qualified service tech-
nician to service the water heater and replace the flamma-
ble vapour sensor. If there is a problem with the wiring of the
flammable vapour sensor or the flammable vapour interface
the LED will flash the failure status code.
CALL FOR
HEAT
IGNITER IS
ENERGIZED AND MAIN
VALVE IS OPENED
Resettable Lockout
The gas control/thermostat can be reset by unplugging the
power cord to remove power and then reinserting the plug
to restore the power. Robertshaw controls will automatically
attempt to reset after a 20 minute wait period. White-
Rodgers Intelli-Vent™ controls will automatically reset after
a 60 minute wait period. Also see "Troubleshooting Guide".
CONTROL CHECKS TO
ENSURE PRESSURE
SWITCH IS OPEN
MAIN BURNER ON AND
THE FLAME IS
SENSED BY CONTROL
BLOWER IS
ENERGIZED
MAIN BURNER
CONTINUES TILL THE
WATER IN THE TANK
REACHES
Water Heater Operation
THERMOSTAT
SETTING
Figure 23 shows the water heater's sequence of operation
when a call for heat is initiated. The ignition control module
will attempt to light the burner three times. If the ignition con-
trol does not detect ignition it will enter lockout mode and
flash the corresponding error code.
CONTROL CHECKS TO
ENSURE PRESSURE
SWITCH CLOSES
INDICATING BLOWER
IS OPERATING AND
THERE ARE NO
MAIN BURNER SHUTS
OFF. BLOWER
CONTINUES FOR A
POST PURGE TIME
VENTING BLOCKAGES
(INLET OR OUTLET)
Figure 23 Sequence Of Operation
3/4” NPT. WRAP
WITH TEFLON TAPE
(2 WRAPS MIN.)
GROUND
CONNECTION
TEMPERATURE
INDICATORS
TEMPERATURE
ADJUSTMENT
BUTTONS
MANIFOLD PRESSURE
ADJUSTMENT (REMOVE
CAP FOR ACCESS)
GAS INLET
1/2” NPT
OUTLET
PRESSURE
PORT
QUICK CONNECTS FOR
POWER SUPPLY AND IGNITER
LOCATED ON UNDERSIDE
GAS
FRO
GAS CONTROL
SIDE VIEW
TO BURNER
IGNITER AND FLAME
PROBE ASSEMBLY
FLAMMABLE
VAPOUR SENSOR
CONNECTOR
BLACK
WHITE
GREEN
TO POWER SUPPLY
DISCONNECT AND
OVERLOAD
PROTECTION
INTELLI-VENTTM
CONTROL
BOTTOM VIEW
HIGH
LIMIT
SWITCH
AIR
PRESSURE
SWITCH
CONNECTOR
COMBUSTION
BLOWER
GREEN
Figure 24 Gas Control/Thermostat Details and Wiring Diagram (White-Rodgers)
– 19 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Check Here
Check Here
Installation Checklist
Water Heater Location
Vent Termination
Horizontal
1.
Centrally located with the water piping system.
Located as close to gas piping and vent pipe
system as possible.
1.
300mm (12 in.) min. above grade/snow level.
2.
Away from corners, other vents, windows etc.
2.
3.
Located indoors and in a vertical position.
Protected from freezing temperatures.
Vertical
1. Exhaust vent termination 450mm (18 in.) min.
above roof/snow level.
Proper clearances from combustible surfaces
maintained and not installed directly on a car-
peted floor.
Water System Piping
1.
Temperature and Pressure relief valve proper-
4.
Provisions made to protect the area from water
damage. Drain pan installed and piped to an
adequate drain.
ly installed with a discharge line run to an open
drain and protected from freezing.
2.
3.
4.
All piping properly installed and free of leaks.
Heater completely filled with water.
5.
6.
Installation area free of corrosive elements and
flammable material.
Closed system pressure build-up precautions
installed.
Sufficient room to service the water heater.
Gas Supply and Piping
Electrical Connections
1.
Gas supply is the same type as listed on the
water heater data plate.
1.
Unit connected to a dedicated 120V electrical
supply.
2.
Gas line equipped with shut-off valve, union
and drip leg
2.
3.
4.
Proper polarity.
Water heater properly grounded.
3.
4.
5.
Approved pipe joint compound used.
Installed in accordance with prevailing provi-
sions of local codes, or in the absence of such,
the latest edition of “Canadian Electrical
Code (CAN/CSA C22.1), Part I” (Canada) or
“National Electrical Code” (NFPA 70)”
(U.S.A.).
Adequate pipe size and of approved material.
Chloride-free soap and water solution or other
approved means used to check all connections
and fittings for possible gas leaks.
Vent Pipe System
1.
2.
Vent pipe and fittings of approved material.
Acceptable size, length and number of elbows
on exhaust vent system.
If the answer to all of the questions
above is “Yes”, read the Operating
3.
Installed in accordance with prevailing provi-
sions of local codes, or in the absence of such,
the latest edition of “Natural Gas and
Propane Installation Code” CAN/CSA-
B149.1 (Canada), or “National Fuel Gas
Code” ANSI Z223.1 (NFPA 54) (U.S.A.).
Instructions and proceed with lighting
the heater.
4.
5.
Horizontal piping slopes at an upward pitch of
3mm (1/8 in.) rise per 1.2m (4 ft). away from
the water heater.
Not obstructed in any way.
– 20 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Mixing Valves
IV) OPERATING INSTRUCTIONS
Hot water can scald: Water heaters are intended to pro-
duce hot water. Water heated to a temperature that will sat-
isfy space heating, clothes washing, dish washing, and
other sanitizing needs can scald and permanently injure you
upon contact. Some people are more likely to be perma-
nently injured by hot water than others. These include the
elderly, children, the infirm, and physically/mentally handi-
capped.
CAUTION:
Read before proceeding. If you do not
follow these instructions exactly, a fire or
explosion may result, causing property
damage, personal injury or loss of life.
If any one using the hot water fits into one of these groups
or if there is a provincial, state or local code requiring a cer-
tain temperature water at the hot water faucet, then you
must take special precautions. In addition to using the low-
est possible temperature setting that will satisfy your hot-
water needs, a means such as a mixing valve, should be
used at the hot-water faucets or at the water heater. Mixing
valves are available at plumbing supply or hardware stores.
Follow manufacturer’s instructions for installation of these
valves. Before changing the factory settings on the thermo-
stat, read the “Temperature Regulation” section in this man-
ual.
This appliance is equipped with an ignition
device that automatically lights the burner.
Do not try to light manually with
a match or flame.
Temperature Regulation
This water heater’s intended purpose is to heat water. Hot
water is needed for cleaning and sanitizing (bodies, dishes,
clothing etc.). Untempered hot water can present a scald
hazard. Depending on the time element and the people
involved (adults, children, elderly, infirm etc.) scalding may
occur at different temperatures.
It is recommended that lower temperatures be used to avoid
the risk of scalding. It is further recommended that the water
temperature be set for the lowest temperature that will sat-
isfy your hot-water needs. This will also provide the most
energy efficient operation of the water heater.
WARNING
Never allow small children to use a hot-water
faucet, or to draw their own bath water.
Never leave a child or impaired person unat-
tended in a bathtub or shower. Scald burns
can result.
Short, repeated heating cycles caused by small water uses
can cause temperatures at the point-of-use to exceed the
thermostat setting by up to 17°C (30°F). This condition is
referred to as “stacking”. If you experience this type of use
you should consider using lower temperature settings to
reduce scald hazards.
Valves for reducing the point-of-use temperature by mixing
cold and hot water are available.
WARNING
DANGER
Scald burns occur in under one second with
71°C (160°F) water, which the thermostat will
deliver if the temperature is set at “VERY
HOT”. Lower settings of the temperature will
reduce the risk of scald and will reduce your
fuel bill.
Water temperature over 52°C (125°F) can cause
severe burns instantly or death from scalds.
WARNING
Risk of scalding
Hot water can produce third degree burns
in 6 seconds at . . . . . . . .60°C (140°F)
in 30 seconds at . . . . . . .54°C (130°F)
in 5 minutes at . . . . . . . . .49°C (120°F)
Children, disabled and elderly are at highest risk of
being scalded.
Feel water before bathing or showering.
Temperature limiting valves are available.
– 21 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Lighting Instructions (Robertshaw)
– 22 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Heater Shutdown
CAUTION:
1. Turn the thermostat dial to the lowest setting.
2. If the heater is running let it shut down first.
3. Turn off all electrical power to the heater or unplug the
power cord from the receptacle.
Read before proceeding. If you do not follow
these instructions exactly, a fire or explosion
may result, causing property damage, per-
sonal injury or loss of life.
4. Press the gas control switch located on the top of the
control. It will automatically turn to the “OFF” position.
5. Turn the manual gas supply valve to the water heater to
the “OFF” position.
Gas Control/Thermostat
This heater may be equipped with the Robertshaw
2000WDER gas control/thermostat and a hot-surface ignit-
er. This control is a combination gas valve, thermostat and
ignition controller for use on this power vented water heater.
The valve contains a micro-controller that supervises the
ignition sequence and monitors the temperature settings
and operation of the heater. The controller also monitors the
flammable vapour safety features of this heater.
System Error Codes
The micro-controller inside the gas control monitors the
flammable vapour safety features, the ignition sequence,
temperature settings and overall operation of the heater. If
any of these parameters does not operate properly the con-
troller will shut down the water heater, diagnose the failure
and flash an error code. Table 3 lists the System Status
Codes for the Robertshaw control. Refer to Table 3 and to
the “Trouble Shooting Guide” to diagnose the problem
before attempting corrective action. See also “Flammable
Vapour Sensor” and “Resettable Lockout”.
This heater is equipped with a hot-surface ignition sys-
tem that automatically ignites the burner. Do not
attempt to light this heater manually with a match or
flame-producing device.
Putting the Heater into Service
1. Turn the manual gas shut-off valve for the heater to the
“ON” position.
2. Turn the gas control switch to “ON”.
3. Follow the Lighting Instructions (Robertshaw) given on
the side of the water heater and also depicted in this
manual. See also “Gas Supply”, “Water Heater
Operation” and “Sequence of Operation”.
Steady ON
Slow Flash
Fast Flash
Control Failure or Miswiring.*
Water Heater is in Stand-by
Mode.
Water Heater is in Heat Mode.
1 flash
1 flash
1 flash
Ignition Failure.
2 flashes
Flammable Vapour Detected.*
Flammable Vapour Sensor
Interface Failure or Miswiring.*
Temperature Adjustment
The temperature dial is adjusted to its lowest tempera-
ture position when shipped from factory.
2 flashes
3 flashes
3 flashes
3 flashes
•
The temperature of the water can be selected by adjust-
ing the temperature dial located on the front of the con-
trol (see Figure 22).
1 flash
Pressure Switch Fails to Open.
Pressure Switch Fails to Close
or Hi-Limit Switch is Open.**
Line/Neutral Polarity Failure.**
ECO Failure.**
Flame is Present at the End of
Heat Cycle.**
3 flashes
•
•
The large arrow position of the thermostat is the pre-
ferred starting point.
Each division on the thermostat dial represents a 3°C
(5°F) water temperature change.
4 flashes
4 flashes
1 flash
2 flashes
4 flashes
5 flashes
3 flashes
-
Note: To avoid scald injury, set the control to the lowest set-
Vacation Mode.
ting that will supply your hot-water needs.
*
System lockout. Call your service provider for
assistance.
There is a hot-water scald potential if the thermostat is set
too high. In households with children, disabled or the elder-
ly, select a lower temperature setting. Tempering valves
(mixing valves) for reducing point-of-use water tempera-
tures are available and may be required by your local
authority. Consult a licensed plumber or your local plumbing
authority.
** System interruption/safety shutdown. Resettable
lock out condition.
Table 3 System Status Codes
WARNING
Risk of scalding
Hot water can produce third degree burns
in 6 seconds at . . . . . . . .60°C (140°F)
in 30 seconds at . . . . . . .54°C (130°F)
in 5 minutes at . . . . . . . . .49°C (120°F)
– 23 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Lighting Instructions (White-Rodgers)
– 24 –
Download from Www.Somanuals.com. All Manuals Search And Download.
The temperature of the water can be selected by using the
temperature adjustment buttons on the front of the gas con-
trol (see Figure 25) as follows:
CAUTION:
Read before proceeding. If you do not follow
these instructions exactly, a fire or explosion
may result, causing property damage, per-
sonal injury or loss of life.
1. “Wake up” the temperature indicators by holding down
both the “COOLER” and “HOTTER” temperature adjust-
ment buttons at the same time for one second. One or
two of the temperature indicators will light up. After 30
seconds, if no other buttons are pushed, the control will
go back to “Sleep” mode and both buttons will again
have to be pressed to see the water temperature set-
ting.
2. Release both of the temperature adjustment buttons.
3. The current water temperature setting will be indicated.
See Table 4 for an explanation of the temperature indi-
cators.
Gas Control/Thermostat
Alternatively, this heater may be equipped with the White-
Rodgers Intelli-VentTM gas control/thermostat and a hot-sur-
face igniter. This control is a combination gas valve, ther-
mostat and ignition controller for use on this power vented
water heater. The valve contains a microcomputer that
supervises the ignition sequence and monitors the temper-
ature settings and operation of the heater. The computer
also monitors the flammable vapour safety features of this
heater.
a. To decrease the temperature press and release the
“COOLER” button once. The temperature indicators
will now display the new temperature setting. Press
and release the “COOLER” button until you have
reached the desired setting.
b. To increase the temperature press and release the
“HOTTER” button once. The temperature indicators
will now display the new temperature setting. Press
and release the “HOTTER” button until you have
reached the desired setting.
This heater is equipped with a White-Rodgers Silicon
Nitride Igniter system that automatically ignites the
burner. Do not attempt to light this heater manually with
a match or flame-producing device.
Putting the Heater into Service
1. Turn the manual gas shut-off valve for the heater to the
“ON” position.
Note: Holding down the button will not continue to lower the
setting. The button must be pressed and released for each
temperature change desired.
Note: To avoid scald injury, set the control to the lowest set-
ting that will supply the hot water for your needs. Refer to
Table 4 to determine the approximate temperature setting,
and the approximate time for scald injury at that tempera-
ture.
2. Follow the Lighting Instructions (White-Rodgers) given
on the side of the water heater and also depicted in this
manual. See also “Gas Supply”, “Water Heater
Operation” and “Sequence of Operation”.
3. Upon start up all the indicator lights on the front of the
control will come on and then turn off. This indicates
that the control has completed a self-diagnostic test and
is ready for operation.
Note: If any of the indicator lights remain on, this indicates
a system fault that needs correcting. See the “System Error
Codes” and “Troubleshooting Guide (White-Rodgers)” for
corrective action.
4. When you have completed setting the control wait 30
seconds for the temperature indicators go off and the
control to enter “Sleep” mode.
APPROXIMATE
TEMPERATURE
°C (°F)
Temperature Adjustment
The control is adjusted to its lowest temperature setting
(approximately 21°C (70°F)) when shipped from factory.
DISPLAY
21°C (70°F)
(VACATION)
TEMPERATURE
INDICATORS
43°C (110°F)
46°C (115°F)
49°C (120°F)
52°C (125°F)
54°C (130°F)
57°C (135°F)
60°C (140°F)
63°C (145°F)*
65°C (150°F)*
TEMPERATURE
ADJUSTMENT
BUTTONS
71°C (160°F)*
FLASHING
* These settings are not available on Hi-input models.
Figure 25 Temperature Indicators and Adjustment
Table 4 Temperature Settings
– 25 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: All the temperature indicators will be off during normal Heater Shutdown
operation. If any time you see the indicators on, there may 1. Turn off all electrical power to the heater or unplug the
be
a
system error and you should consult the
power cord from the receptacle.
“Troubleshooting” section of this document, or contact a 2. Turn the manual gas supply valve to the water heater to
trained service professional.
the “OFF” position.
System Error Codes
WARNING
The computer inside the gas control monitors the flammable
vapour safety features, the ignition sequence, temperature
settings and overall operation of the heater. If any of these
parameters does not operate properly the computer will
shut down the water heater and flash an error code. See the
Scald burns occur in under one second with
71°C (160°F) water, which this thermostat will
deliver if the temperature is set at “VERY
HOT”. Lower settings of the temperature will
reduce the risk of scald and will reduce your
fuel bill.
“System
Error
Codes
(White-Rodgers)”
and
“Troubleshooting Guide (White-Rodgers)” to diagnose the
problem before attempting corrective action. See also
“Flammable Vapour Sensor” and “Resettable Lockout”.
There is a hot-water scald potential if the thermostat is set
too high. In households with children, disabled or the elder-
ly, select a lower temperature setting. Valves for reducing
point-of-use temperature by mixing hot and cold water are
available. Consult a licensed plumber or the local plumbing
authority.
TM
Intelli-Vent System Error Codes
SYMPTOM
CORRECTIVE ACTION
POSSIBLE CAUSE(S)
An open earth ground circuit to 1. Check that the earth ground conductor is properly connected at the
Error 1
the ignition system.
fuse box or breaker panel and the water heater.
2. Check that the grounding conductors on the water heater are prop-
erly connected and secure.
The self diagnostic test detect- 1. Check for proper connection of the line neutral and line hot wires.
ed a wiring error, reversed 2. Check that the appliance is securely connected to earth ground.
polarity or a high resistance to
Error 2
Error 3
Error 4
earth ground.
The pressure switch remained 1. The pressure switch wiring is incorrect.
closed longer than 5 seconds 2. The pressure switch is defective and must be replaced.
after the call for heat began.
Blower does not start.
The pressure switch remained 1. The pressure switch wiring is incorrect.
open longer than 5 seconds 2. The pressure switch tubing is not connected correctly.
after the combustion blower 3. Obstructions or restrictions in the water heater air intake or exhaust
was energized.
flue.
4. Check the high temperature limit switch.
The self diagnostic test has 1. Check that all wiring is correct and secure.
detected an error in the hot- 2. Disconnect the igniter connector and measure the igniter resistance
Error 5
Error 6
surface igniter circuit.
with an accurate ohmmeter between pins 1 and 2. Resistance
should be between 11.5 and 18.8 ohms. If the reading is incorrect,
replace the hot-surface igniter.
3. If the above checks are good, replace the control.
The maximum number of igni- 1. Ensure the igniter is positioned correctly.
tion retries or recycles has 2. Ensure the voltage to the water heater is 115-125 VAC.
been reached and the system 3. Clear any obstructions or restrictions in the water heater air intake
is in lockout for an hour. Cycle
the power to the water heater
off and on to reset.
or exhaust flue.
Table 5 Intelli-VentTM System Error Codes.
– 26 –
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMPTOM
CORRECTIVE ACTION
The self-diagnostic test found 1. Cycle power to the water heater “OFF” for 10 seconds and then
POSSIBLE CAUSE(S)
Error 7
a problem with the gas valve
driver circuit.
back “ON”.
2. If the above step did not clear the error, the control must be
replaced.
The self-diagnostic test has 1. Cycle the external power “OFF” for 10 seconds and then back “ON”.
detected a problem with the 2. If the above step does not clear the error, the control must be
Error 8
Error 9
internal microcomputer.
replaced.
The self-diagnostic test has 1. Cycle the external power “OFF” for 10 seconds and then back “ON”.
detected a problem with the 2. If the above step does not clear the error, the control must be
internal circuit.
replaced.
Flame signal sensed out of 1. Insure flame sensor ceramic insulator is not cracked.
Error 10
Error 11
Error 12
proper sequence.
2. Turn power off for 10-20 seconds, and then on again to clear the
error code.
3. Replace the control.
The high temperature thermal 1. Turn the power off for 10-20 seconds then on again to clear the
cutoff is open.
error code.
2. Replace the control.
The self-diagnostic test has 1. Make sure that there are no objects leaning against the front of the
detected one of the tempera- control.
ture adjust buttons stuck 2. Lightly press and release each of the buttons once.
closed.
3. If the above actions do not clear the error, the control will continue
to regulate water temperature at the last setting, but you will not be
able to change settings unless you replace the control.
The self-diagnostic test has 1. Turn the power off for 10-20 seconds then on again to clear this
detected that the water tem- error code.
perature sensor is either open 2. If no wiring problems are found the control must be replaced.
or short circuited.
Error 13
Error 14
The self-diagnostic test found 1. Check that all wiring is correct and that there are no open or short
a problem with the Flammable
Vapour Wiring.
circuits.
The control detected the pres- 1. Check for and remove any sources of flammable vapours.
ence of flammable vapours 2. Check the resistance of the FV sensor. If the resistance is more
Error 15
near the appliance and
entered lockout.
than 100K ohms replace the sensor.
3. If the water heater is in operating condition replace the control.
Table 5 (cont’d) Intelli-VentTM System Error Codes.
– 27 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Smoke/Odour
V) OPERATION
The water heater may give off a small amount of smoke and
odour during the initial start-up of the unit. This is due to the
burning off of oil from metal parts of a new unit and will dis-
appear after a few minutes of operation.
Burner Flames
Inspect the burner flames through the viewport and com-
pare them to the drawings in Figure 26. A properly operat-
ing burner should produce a soft blue flame. Blue tips with
light blue inner cones are satisfactory. The tips of the flame
may have a slight yellow tint. The flame should not be all
yellow or have a sharp blue-orange colour. Contaminated
air may cause an orange coloured flame. Contact a qualified
service technician if the flame is not satisfactory.
Anode Rod/Water Odour
Each water heater contains at least one anode rod, which
will slowly deplete while protecting the glass-lined tank from
corrosion and prolonging the life of the water heater. Once
the anode is depleted, the tank will start to corrode, eventu-
ally developing a leak. Certain water conditions will cause a
reaction between this rod and the water. The most common
complaint associated with the anode rod is a "rotten egg
smell" produced from the presence of hydrogen sulfide gas
dissolved in the water. Do not remove this rod perma-
nently as it will void any warranties, stated or implied. A
special anode can be ordered if water odour or discoloura-
tion occurs. This rod may reduce, if not eliminate, water
odour problems. The water supply system may require
special filtration equipment from water conditioning compa-
ny to successfully eliminate all water odour problems.
Artificially softened water is exceedingly corrosive because
the process substitutes sodium ions for magnesium and cal-
cium ions. The use of a water softener may decrease the life
of the water heater tank. The anode rod should be inspect-
ed every year. If the rod is more than 50% depleted, the
anode rod should be replaced. See “Anode Rod
Replacement” in the Maintenance section of this manual.
BLUE TIPS
LIGHT BLUE INNER
INCORRECT
CONES ARE SATIS-
FLAME LAZY
FACTORY
YELLOW
CORRECT FLAME
SOFT BLUE
Figure 26 Flame Characteristics
Operational Conditions
Condensation
Moisture from the products of combustion condenses on the
tank surface and forms drops of water that may fall onto the
burner or other hot surfaces. This will produce a "sizzling" or
"frying" noise. This condensation is normal and should not
be confused with a leaking tank. Condensation may
increase or decrease at different times of the year. High effi-
cient energy saver water heaters will produce larger
amounts of condensation on initial start-up or when a large
amount of hot water is being used. Do not confuse this with
a "tank leak". Once the water reaches a temperature of
49°C (120°F) and the tank warms up (usually 1-2 hours),
the condensation will stop.
VI) MAINTENANCE
Draining and Flushing
It is recommended that the tank be drained and flushed
every 6 months to remove sediment that may build up dur-
ing operation. The water heater should be drained if being
shut down during freezing temperatures. To drain the tank,
perform the following steps:
Important: It is always recommended that a suitable drain
pan be installed under the water heater to protect the area
from water damage resulting from condensation, a leaking
tank or piping connections. Refer to "Location
Requirements". Under no circumstances is the manufactur-
er to be held responsible for any water damage in connec-
tion with this water heater.
1. Turn off the gas to the water heater at the manual gas
shut-off valve.
2. Turn off the electrical supply to the water heater.
3. Close the cold-water inlet valve.
4. Open a nearby hot-water faucet.
5. Connect a hose to the drain valve and terminate it to an
adequate drain.
Note: The drain hose should be rated for at least 93°C
(200°F). If the drain hose does not have this rating, open the
cold-water inlet valve and a nearby hot-water faucet until
the water is no longer hot.
6. Open the water heater drain valve and allow all the
water to drain from the tank. Flush the tank with water
as needed to remove sediment.
Water Heater Sounds
During the normal operation of the water heater, sounds or
noises may be heard. These noises are common and may
result from the following:
1. Normal expansion and contraction of metal parts during
periods of heat-up and cool-down.
2. Condensation causes sizzling and popping within the
burner area and should be considered normal.
3. Sediment buildup in the tank bottom will create varying
amounts of noise and may cause premature tank fail-
ure. Drain and flush the tank as directed under
"Draining and Flushing".
7. Close the drain valve, refill the tank, and restart the
heater as directed under "Water Heater Operation".
If the water heater is going to be shut down for an extended
period, the drain valve should be left open.
Important: Condensation may occur when refilling the tank
and should not be confused with a tank leak.
– 28 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Anode Rod Replacement
Temperature and Pressure Relief Valve
To replace the anode:
WARNING
1. Turn off gas supply to the water heater.
2. Shut off the water supply and open a nearby hot-water
faucet to depressurize the water tank.
3. Drain approximately 20 litres (5 US gallons) of water
from tank (Refer to "Draining and Flushing" for proper
procedures.) Close drain valve.
4. Remove old anode rod.
5. Use Teflon® tape or approved pipe sealant on threads
and install new anode rod.
Explosion Hazard
• If the temperature and pressure relief
valve is dripping or leaking, have a
licensed plumber repair it.
6. Turn on water supply and open nearby hot-water faucet
to purge air from water system.
• Do not plug valve.
• Do not remove valve.
• Failure to follow these instructions can
result in death or an explosion.
7. Restart the water heater as directed under "Operating
Your Water Heater." See the "Parts Reference
Illustration" for anode rod location.
Manually operate the temperature and pressure relief valve
at least once a year to make sure it is working properly (see
Figure 27). To prevent water damage, the valve must be
properly connected to a discharge line that terminates at an
adequate drain. Standing clear of the outlet (discharged
water may be hot), slowly lift and release the lever handle
on the temperature and pressure relief valve to allow the
valve to operate freely and return to its closed position. If the
valve fails to completely reset and continues to release
water, immediately shut off the manual gas valve and the
cold-water inlet valve and call a qualified service technician.
Routine Preventative Maintenance
Important: If you lack the necessary skills required to prop-
erly perform this visual inspection, you should not proceed,
but get help from a qualified service technician.
At least annually, a visual inspection should be made of the
venting and air supply system, piping systems and main
burner. Check the water heater for the following:
•
Build up of soot and carbon on the main burner. Check
for a soft blue flame.
•
•
Leaking or damaged water and gas piping.
Presence of flammable or corrosive materials in the
installation area.
Temperature and Pressure
Relief Valve
•
•
Presence of combustible materials near the water
heater.
Verify proper operation after servicing this water heater.
Manual Relief Valve
Gas Control
There are no user serviceable parts in this control. The con-
trol is supplied with tamper resistant screws. DO NOT
attempt to repair or adjust the control. If you experience
problems, discontinue use and replace the control immedi-
ately. Continuing to use a damaged control could result in
fire and/or explosion.
Discharge line to drain
If you wish to verify that the water heater is operating prop-
erly:
Figure 27 T&P Valve Test
1. Make sure there is power to the water heater.
2. Make sure that the gas is turned on to the water heater.
3. Initiate a call for heat by either drawing hot water from a
nearby faucet or raising the temperature setting (see
section “Temperature Regulation”).
4. Note any error codes that appear and proceed to the
“Troubleshooting” section.
– 29 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Venting System and Blower
WARNING
Keep the area around the heater clear and
unobstructed.
Inspect the venting system periodically (minimum twice
annually) to make certain that the vent passageways, vent
terminal and blower assembly are free and unobstructed.
Ensure that any condensate is draining freely. Clean as nec-
essary.
•
Inspect the vent piping, elbows and connections for
signs of stress cracking or deterioration. Make certain
the venting is free to move and that all pipe hangers and
isolation supports are properly positioned and securely
attached. Replace any broken components and rectify
any installation problems.
•
Particles, especially lint, can clog the vent blower
wheel. This can be problematic, especially where con-
densation is present, as particles may adhere to the
venting surfaces. These conditions can result in nui-
sance failures. In areas that have a high level of air-
borne particulate (e.g. lint, sawdust, process smoke,
laundry areas, etc.) inspection and cleaning may need
to be done more frequently. Clean the blower wheel and
venting as required to ensure proper performance.
Inspect the flue collector area for signs of corrosion.
This can be an indication of contaminated air, a wet
environment, poor burner set up, or high levels of con-
densation occurring at the flue collector. Determine and
correct any poor operating conditions.
•
DRAFT
AIR PRESSURE
DIVERTER
TUBING
AIR INTAKE
MOTOR
VENTILATION
OPENINGS
OPENING FOR
DRAFT DIVERTER
BLOWER
MOTOR
L I M I T
SWITCH
LIMIT
SWITCH
WIRES
Figure 28 Blower Maintenance
– 30 –
Download from Www.Somanuals.com. All Manuals Search And Download.
VII) COMBO HEATING
2. Install a drain valve at the lowest point of the heating
loop so that water can be drained from the heating mod-
ule without affecting the water heater.
3. If the air handler does not have a venting means at the
highest point of the piping arrangement, install an air
bleed at the highest point of the plumbing arrangement.
This section serves as a guide for the installation and use of
"Combo" heating systems utilizing a domestic water heater
that has been specifically approved for such use. It is writ-
ten for those knowledgeable in the required trades and pro-
fessionals involved in the design and installation of Combo
Heating Systems.
It is the responsibility of the installer/designer to follow
all applicable codes to ensure the effectiveness and
safety of the installation.
System Requirements
The following requirements must be met for the installation
of Combo Heating Systems:
1. All components used for the distribution of water in the
heating loop must be suitable for potable water. These
include all piping, fittings, solder and fluxes, pumps for
circulation of water, valves, etc.
CHECK VALVE
EXPANSION TANK
COLD
SUPPLY
(IF USED
REQUIRES
EXPANSION
TANK)
(OPTIONAL)
HOT WATER
TO HOUSE
FIXTURE
MIXING
VALVE
2. The water heater must not be connected to a hydronic
heating system that has been used previously.
3. No boiler treatment chemicals of any kind shall be intro-
duced into the system.
C
H
8in TO 12in
MAX.
M
CHECK
VALVE
COLD
INLET
H
O
T
4. The Combo System components must be selected and
sized to meet and maintain the total calculated
demands for both domestic service hot water and space
heating requirement. The sizing and installation must be
performed in accordance with good engineering prac-
tice such as "ASHRAE Handbooks", HRAI,
"Hydronics Institute Manuals", CSA B149.1, NFPA
54, ANSI Z223.1, CSA F280, National/Provincial
Building Codes, CSA C22.1, ANSI/NFPA 70, CSA
B51 and/or codes having jurisdiction.
OUTLET
EXTERNAL
CIRCULATOR
FLOW
CONTROL
SUPPLY
HOSE BIB
(OPTIONAL)
WATER
HEATER
RETURN
DRAIN/PURGE
VALVE
I N T E R N A L
CIRCULATOR
5. The air handler (fan coil) and/or the circulating pump in
a baseboard hydronic loop will require a dedicated
120V circuit. This must be provided and identified for
this purpose.
AIR HANDLER
Figure 29 Combo Heating - Air Handler
CHECK VALVE
(IF USED
REQUIRES
EXPANSION
TANK)
6. All piping between the water heater and the air handler
or hydronic baseboard loop must be adequately insulat-
ed to reduce heat loss.
7. If the local jurisdiction requires a back-flow preventer in
the cold water line, an expansion tank of adequate size
must be installed.
EXPANSION TANK
COLD
SUPPLY
(OPTIONAL)
HOT WATER
TO HOUSE
FIXTURE
MIXING
VALVE
8. "Combo" Heating Systems require higher water temper-
atures than other applications. When the system is
used to supply water for Combo Heating applications, a
means, such as mixing valve, must be installed to tem-
per the water in order to reduce scald hazard potential
(see Figures 29 & 30).
C
H
8in TO 12in
MAX.
M
CHECK
VALVE
COLD
INLET
H
O
T
OUTLET
EXTERNAL
CIRCULATOR
FLOW
CONTROL
SUPPLY
HOSE BIB
(OPTIONAL)
Installation
WATER
HEATER
The heating mode may be one of the following options:
A. A fan coil/air handler (Figure 29).
RETURN
B. A hydronic baseboard (finned tube) loop/In floor heating
(Figure 30).
The following is a list of requirements for the installation of
the heating loop to the water heater.
HYDRONIC
BASEBOARDS
(SERIES CON-
NECTED
SHOWN)
1. Install shut-off valves and unions so that the water
heater can be isolated from the heating module should
servicing of the water heater become necessary.
Figure 30 Combo Heating - Baseboard
– 31 –
Download from Www.Somanuals.com. All Manuals Search And Download.
VIII) TROUBLESHOOTING GUIDE
Robertshaw 2000WDER and White-Rodgers Intelli-Vent
TM
SYMPTOM
CORRECTIVE ACTION
POSSIBLE CAUSE(S)
1. No Power to unit.
2. Thermostat setting too low.
1. Plug in power cord, check fuses/supply
voltage.
3. Defective air pressure switch (must be 2. Increase thermostat temperature set-
BLOWER WILL NOT
START.
open at start-up before blower is ener-
gized).
4. Defective blower.
ting.
3. Replace air pressure switch.
4. Replace blower.
5. Disconnected or loose wire.
6. Control locked out.
5. Repair/reconnect wires.
6. Reset – determine cause of lockout.
1. Air pressure switch not closing due to 1. Determine cause of insufficient draft.
insufficient draft - check for:
Check draft with manometer at pres-
sure switch (refer to Table 2 for mini-
mum acceptable draft settings).
a) remove blockage,
b) reduce vent length/increase vent
size,
a) vent piping blocked,
b) piping length too long,
c) frozen vent termination,
d) clogged/dirty blower.
2. Disconnected, torn or blocked pressure
c) clear termination of snow/ice,
d) clean blower wheel.
BLOWER RUNS
CONTINUOUSLY.
sensing tubing from air pressure switch 2. Reconnect or replace pressure sensing
to blower housing. tubing.
3. Air pressure switch not closing due to 3. Replace defective pressure switch.
defective switch.
4. High limit switch open due to excessive
vent temperature or defective switch.
4. Determine cause of overheating check
for: overfiring, insufficient air supply,
high ambient air temperature (once
activated high limit must be replaced).
1. 120VAC polarity reversed at 120VAC 1. Reverse polarity at 120VAC outlet
outlet receptacle.
2. Defective hot-surface igniter.
receptacle.
HOT-SURFACE IGNITER
NOT GLOWING FOLLOW-
ING WARM-UP PERIOD.
2. Replace igniter (Check for 120VAC
across I1 & I2, Robertshaw only).
3. Replace control.
3. Defective Control.
4. Defective Flammable Vapour Sensor.
4. Replace Flammable Vapour Sensor.
1. No gas supply.
1. Check/turn on gas supply.
2. Gas control switch in “OFF” position.
3. Insufficient gas supply.
2. Turn control switch to “ON” position.
3. Ensure correct supply pressure for gas
type (Nat Gas 7.0 in. w.c. (1.74 kPa))
(Propane 11.0 in. w.c. (2.74 kPa)).
4. Check/adjust for correct manifold gas
pressure (NG 3.5 in. w.c.(0.87 kPa)),
(Propane 10.0 in. w.c. (2.49 kPa)).
5. Ensure correct gas type for water
heater model.
4. Incorrect manifold gas pressure.
5. Incorrect gas type.
6. Defective igniter/loose or disconnected
wire.
CONTROL LOCKED OUT.
6. Replace defective igniter/reconnect
wiring.
7. Improperly positioned, dirty, or defec-
tive flame rod/loose or disconnected 7. Reposition, clean, or replace defective
wire.
flame rod/reconnect wiring.
8. Remove obstruction.
9 Remove blockage/clean flue.
10.Replace Control.
8. Burner orifice clogged.
9. Blocked water heater flue.
10.Defective control.
11.Defective Flammable Vapour Sensor.
11.Replace Defective Flammable Vapour
Sensor.
1. Internal control fault.
1. Replace control.
2. ECO failure – excessive water temper- 2. Replace control.
ature.
CONTROL LOCKED OUT.
*SOLID GREEN LED.
3. Excessive humidity/damp environment. 3. Allow control to dry.
– 32 –
Download from Www.Somanuals.com. All Manuals Search And Download.
IX) REFERENCE PARTS
19. Air Inlet Snorkel
Reference Parts Listing
Replacement parts may be ordered through your plumber or
the local distributor. When ordering replacement parts,
always have the following information ready:
1. Model, Serial and Product number
2. Type of gas
3. Item number
4. Parts description
See "Parts Reference Illustration" for a list of available
repair parts.
20. Combo Heating System Supply Outlet (Optional)
21. Power Cord
22. Air Switch (inside box)
23. Junction Box
24. Junction Box Cover
25. Air Tubing
26. Rubber Coupling
27. Gear Clamp
28. Draft Diverter
29. Hot-Water Outlet Nipple
30. Anode (under cap)
31. Cold-Water Inlet Nipple
32. Flexible Manifold Tube
33. Viewport
34. Hot-Surface Igniter
35. Gas Orifice
36. Sheet Metal Burner
37. Gas Manifold
38. Flame Sensor Rod
39. Manifold Door Gasket
40. Manifold Door
41. Two Piece Grommet With Clip
42. *Gas Control/Thermostat (White-Rodgers) (not shown)
1. Vent Termination Elbow with Rodent Screen
2. **Vent Pipe
3. **Vent Pipe Coupling (if required)
4. **Vent Pipe Elbow (long radius)
5. Limit Switch
6. T&P Valve
7. Diptube
8. Baffle Assembly
9. Driptube
10. *Gas Control/Thermostat (Robertshaw)
11. Gas Control/Thermostat Cover (Robertshaw)
12. Drain Valve
13. Outer Gas Door
14. Manifold Door Assembly (behind outer door)
15. **Floor Drain
16. **Drain Pan
17. Flammable Vapour Sensor (under cover)
18. Combo Heating System Return Inlet (Optional)
*
Robertshaw and White-Rodgers systems are not
interchangeable.
** Items not supplied with the water heater.
– 33 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Reference Illustration
27
31
6
28
29
30
1
2
3
4
5
26
25
23 24
22
21
20
19
6
Rear View
7
8
9
33
32
34
35
42
11
36
10
12
18
17
37
38
14
13
15
16
39
41
40
*Robertshaw Equipped
Front View
*
Robertshaw and White-Rodgers systems are not
interchangeable.
34
38
36
35
32
33
37
39
40
41
*White-Rodgers Equipped
Figure 31 Parts Reference
– 34 –
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
When referencing the water heater for service or warranty, please refer to the rating plate afꢀxed to the unit for the following
information:
Use Copper Conductors Only
Model Number
AUTOMATIC STORAGE WATER HEATER
For currenlly installed rating see element marking.
Caution: Pressure relief valve Iimiting the pressure
to 1034 kPa (150 psI) musl be installed.
For safe operation, do not block pressure relief.
This lank is equipped with
a
temperature limit
Warranty Code:
P
3
1
R
5
1
S
6
1
U
8
2
V
9
1
W
Y
Catalogue Number
(SKU)
device located under the upper access door.
CAUIlON: Risk of electrlc shock. Turn off power
before opening access door. Do not turn on electric
current until tank is full of water. Elements wlll bum
out if tank is operated without water.
Pour seulement conducteurs copper
ACCUMIl.ATlON AUTOMATIQUE
La puissance installee est indiquee sur l'element.
ATTENTION: Une soupape de securite limitant la
CHAUFFE-EAU
A
Inner Tank Warranty Years:
Component Part Warranty Years:
10 12
pression
a
1034 kPa (150 psi) doit etre installee.
Pour un fonctionment securitaire, ne pas enlever
ou bloquer cette soupape.
Ce reservoir est muni d'un dispositif reglage
automatique de la temperature situe sous la porte
d'acces superieure.
ATTENTION: Risque de choc electrique. Coupez le
courant avant d'ouvrir la porte d'acces. Ne
remettez pas le courant en marche avant que le
reservoir soit remplis d'eau. Si le reservoir
fonctionment sans eau, les elements bruleront.
Rating Plate
1
1
Serial Number
The Serial Number contains the warranty and manufacture date information for the unit as follows:
U9999 F999999
Example: U1005 F001234
Warranty code
Year of manufacture
Week of manufacture
Manufactured in week 5
Manufactured in 2010
8 year tank, 2 year parts warranty
The Warranty Code indicates the inner tank and component part warranties as shown in the table above.
LIMITED WARRANTY
RESIDENTIAL STORAGE TANK TYPE WATER HEATER FOR INSTALLATION IN A SINGLE FAMILY DWELLING
A. WHO IS COVERED.
GSW WATER HEATING AND ITS SUPPLIERS, (herein collectively referred to as “Manufacturer”) warrants only to the
original consumer purchaser (hereinafter “Owner”) of the water heater, within the boundaries of the continental United
States or Canada, or their territories, so long as he or she continuously occupies the single family dwelling in which this
water heater is initially installed for the period speciꢀed below. This Warranty is not transferable. This Warranty is reduced
to one year if the water heater is used in a commercial or industrial application, or if the water heater is used to supply
more than one dwelling unit. Consumers must retain point-of-sale proof of purchase to validate warranty entitlement.
B. WHEN IT IS COVERED.
The water heater is warranted only when it is installed, operated, and maintained in accordance with the printed instruc-
tions accompanying the water heater. The water heater shall/must be installed in such a manner that, if the tank or any
connection thereto should leak, the resulting ꢁow of water will not cause damage to the area in which it is installed. The
water heater’s temperature and pressure relief valve must be piped to the nearest drain to avoid damage in the event the
valve is actuated. For detailed instructions, read the manual accompanying the water heater and review drawings in the
manual.
C. WHAT THE MANUFACTURER WILL DO AND THE PERIOD OF COVERAGE.
1. The Inner Tank. If the inner tank leaks within the warranty period shown in the table above after the original installa-
tion, the Manufacturer will furnish a new water heater of the Manufacturer’s then prevailing comparable model. If in-
dustry standards, regulatory changes, product improvements, or product obsolescence prohibits the Manufacturer from
furnishing an identical model replacement water heater under this Warranty, the Owner will be furnished with a new
water heater of comparable capacity; however, the Owner will be charged for the additional value of the item(s) which
the Manufacturer has incorporated in the replacement water heater. A prior authorization number must be obtained
from the Manufacturer before replacing the water heater. This Warranty is limited to one replacement water heater at
the original installation site.
2. Component Part. If any component, part other than the inner tank, proves to the Manufacturer’s satisfaction to be
defective in material or workmanship within the warranty period shown in the table above after the original installation,
the Manufacturer will furnish the Owner with a replacement for the defective part(s). This Warranty is limited to one
replacement component part for each original part.
3. Return of Defective Water Heater and Component Parts. The Manufacturer reserves the right to examine the al-
leged defect in the water heater or component part(s). As such, it will be the Owner’s obligation (see paragraph D. 3) to
return the water heater and/or component part(s) to the Manufacturer.
a. When returning a water heater, it must include all component parts and the rating plate label.
b. When returning component part(s), they must be individually tagged and identiꢀed with the water heater’s Model
Number, SKU, Serial Number, date of purchase, and date of installation.
c. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. THIS
EXPRESS WARRANTY IS, WHERE PERMITTED BY LAW, IN LIEU OF AND EXCLUDES AND REPLACES ALL
OTHER CONDITIONS, WARRANTIES, GUARANTEES, REPRESENTATIONS, OBLIGATIONS OR LIABILITIES
OF THE MANUFACTURER OF ANY NATURE OR KIND, EXPRESS OR IMPLIED, HOWEVER ARISING (WHETH-
ER BY CONTRACT, CONDUCT, STATEMENT, STATUTE, NEGLIGENCE, PRINCIPLES OF MANUFACTURER’S
LIABILITY, OPERATION OF LAW, OR OTHERWISE) WITH RESPECT TO THE UNIT OR ITS FIRNESS FOR A
PARTICULAR PURPOSE, METCHANTABILITY, INSTALLATION, OPERATION, REPAIR, OR REPLACEMENT.
THE MANUFACTURER EXPRESSLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES. IN NO EVENT WILL
THE MANUFACTURER’S LIABILITIES EXCEED THE COST OF THE DEFECTIVE PART(S) OR UNIT.
D. WHAT THIS WARRANTY DOES NOT COVER.
1. The Unit must not be installed where water damage can result from a leak, while provision(s) shall be made for direct-
ing any water escaping from the Unit to a properly operating drainpipe. As all units of this type may eventually leak,
you must protect against any potential water damage. The Manufacturer accepts no responsibility for such damage,
nor any incidental or consequential loss, nor damage(s) related thereto, suffered by the Owner of the Unit nor by any
third party.
2. The Manufacturer shall not be liable under this Warranty and this Warranty shall be void and have no effect if the fol-
lowing events occur:
a. The water heater or any of its component parts have been subject to misuse, alteration, neglect, or accident; or
Download from Www.Somanuals–.co3m5. A–ll Manuals Search And Download.
b. The water heater has not been installed in accordance with the applicable local plumbing and/or building code(s)
and/or regulations or, in their absence, with the latest edition of the Natural Gas and Propane Installation Code,
and/or the Canadian Electrical Code; or
c. The water heater is not installed, operated, and maintained in accordance with the Manufacturer’s instructions,
including if the water heater has any additional aftermarket equipment introduced into the sealed system not ap-
proved by the Manufacturer; or
d. The water heater or any of its component parts are damaged or fails from operation with an empty or partially empty
tank (such as, but not limited to elements burned out in a dry tank); or
e. The water heater or any part has been under water; or
f. The water heater is exposed to highly corrosive atmospheric conditions. No warranty extends, for example, and
without limitation of the foregoing, to Units exposed to: salts, chemicals, exhausts, pollutants, or contaminants; or
g. The water heater is not continuously supplied with potable water; or
h. The water heater replacement is requested for reasons of noise, taste, odour, discolouration, and/or rust; or
i. The water heater is operated at temperatures exceeding the maximum setting of the thermostat and/or high limit
control provided by the Manufacturer, or at water pressures exceeding the pressure reading stated on the Unit; or
j. The water heater is operated without an operating anode; or
k. The water heater is supplied or operated with deionized water; or
l. The water heater is removed from its original installation location; or
m.The water heater is installed outdoors (this water heater is intended only for indoor installation); or
n. The water heater is converted, or is attempted to be converted, from one voltage or wattage to another, if an electric
water heater, or from one gas type to another, if a gas water heater; or
o. The water heater has not been ꢀred at the factory rated input and fuel for which it was factory built; or
p. The water heater or any of its component parts fail due to sediment build-up; or
q. The water heater does not have installed a properly operating temperature and pressure relief valve, certiꢀed to
ANSI Z21.22/CSA “Requirements for Relief Valves for Hot Water Supply Systems”; or
r. The water heater or any of its component parts fail because of ꢀre, ꢁoods, lightning, or any other act of God, or any
other contingency beyond the control of the Manufacturer; or
s. The water heater is installed in a closed system without adequate provision for thermal expansion.
3. Except when speciꢀcally prohibited by the applicable law, the Owner, and not the Manufacturer, shall be liable for
and shall pay for all charges for labour or other expenses incurred in the removal, repair, or replacement of the water
heater or any component part(s) claimed to be defective or any expense incurred to remedy any defect in the product.
Such charges may include, but are not necessarily limited to:
a. All freight, shipping, handling, and delivery costs of forwarding a new water heater or replacement part(s) to the
Owner.
b. All costs necessary or incidental in removing the defective water heater or component part(s) and installing a new
water heater or component part(s).
c. Any material required to complete and/or permits required for the installation of a new water heater or replacement
part(s), and
d. All costs necessary or incidental in returning the defective water heater or component part(s) to a location desig-
nated by the Manufacturer.
4. The terms of this Limited Warranty cannot be modiꢀed by any person, whether or not he/she claims to represent or
act on behalf of the Manufacturer.
E. HOW THE ORIGINAL OWNER CAN MAKE A WARRANTY CLAIM.
1. The Owner should submit the warranty claim direct to the Manufacturer’s Service Department, at the address or phone
number listed below, and the Manufacturer will arrange for the handling of the claim.
2. Whenever any inquiry or request is made, be sure to include the water heater’s Catalogue Number, Model Number,
Serial Number, date of purchase, date of installation, and location of installation.
This Warranty and the Manufacturer’s obligations shall be construed and determined in accordance with the laws of both the
Province of Ontario, and of Canada in force therein. This Warranty does not affect speciꢀc legal rights of a consumer under
applicable law, except to the extent that such rights may e waived or replaced, and the provisions hereof are deemed to be
amended to the extent necessary. The unenforceability of any provision, in whole or in part, of this Certiꢀcate shall not affect
the remaining provisions. Any and all repair and/or replacement of part(s) or Unit are the sole and exclusive remedy avail-
able against the Manufacturer.
GSW Water Heating
599 Hill Street West
Fergus, ON Canada N1M 2X1
Should you have any questions, please
E-mail us at [email protected], or
Call our Technical Support line at 1 888 GSW TECH (479 8324)
Download from Www.Somanuals–.co3m6. A–ll Manuals Search And Download.
|