GPX TV DVD Combo TDE2480 User Manual

USER’S GUIDE  
V:1153-1008-10  
TDE2480  
24” Class TV/DVD Combo  
For the most up-to-date version of this User’s Guide, go to www.gpx.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Important Safety Instructions  
1. Read these Instructions.  
FCC Warnings  
WARNING: Changes or modifications to this unit not expressly  
2. Keep these Instructions.  
approved by the party responsible for compliance could void the  
user’s authority to operate the equipment.  
3. Heed all Warnings.  
4. Follow all instructions.  
NOTE: This equipment has been tested and found to comply with  
the limits for a Class B digital device, pursuant to Part 15 of the FCC  
Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This  
equipment generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications. However,  
there is no guarantee that interference will not occur in a particular  
installation. If this equipment does cause harmful interference to  
radio or television reception, which can be determined by turning  
the equipment off and on, the user is encouraged to try to correct the  
interference by one or more of the following measures:  
5. Do not use this apparatus near water.  
6. Clean only with a dry cloth.  
7. Do not block any ventilation openings. Install in  
accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as radiators,  
heat registers, stoves, or other apparatus (including  
amplifiers) that produce heat.  
9. Do not defeat the safety purpose of the polarized or  
grounding - type plug. A polarized plug has two blades  
with one wider than the other. A grounding type plug  
has two blades and a third grounding prong. The wide  
blade or the third prong are provided for your safety.  
When the provided plug does not fit into your outlet,  
consult an electrician for replacement of the obsolete  
outlet.  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from  
that to which the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Additional Warnings  
• The apparatus shall not be exposed to dripping or splashing and  
that no objects filled with liquids, such as vases, shall be placed on  
apparatus.  
10. Protect the power cord from being walked on or  
pinched particularly at plugs, convenience receptacles,  
and the point where they exit from the apparatus.  
L’appareil ne doit pas être exposé aux écoulements ou aux  
éclaboussures et aucun objet ne contenant de liquide, tel qu’un  
vase, ne doit être placé sur l’objet.  
11. Only use attachments/accessories specified by the  
manufacturer.  
• Main plug is used as disconnect device and it should remain readily  
operable during intended use. In order to disconnect the apparatus  
from the mains completely, the mains plug should be disconnected  
form the mains socket outlet completely.  
La prise du secteur ne doit pas être obstruée ou doit être facilement  
accessible pendant son utilisation. Pour être complètement  
déconnecté de l’alimentation d’entrée, la prise doit être débranchée  
du secteur.  
Use only with a cart, stand, tripod,  
bracket, or table specified by the  
manufacturer, or sold with the apparatus.  
When a cart is used, use caution when  
moving the cart/apparatus combination to  
avoid injury from tip-over.  
12.  
• Battery shall not be exposed to excessive heat such as sunshine, fire  
or the like.  
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la  
lumière du soleil, au feu ou autres choses de semblable.  
13. Unplug this apparatus during lightning storms or when  
unused for long periods of time.  
• Caution marking is located at the rear or back of the apparatus.  
14. Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has been  
damaged in any way, such as power-supply cord or  
plug is damaged, liquid has been spilled or objects  
have fallen into the apparatus, the apparatus has been  
exposed to rain or moisture, does not operate normally,  
or has been dropped.  
Attention marquage est situé à l’arrière ou à l’arrière de l’appareil  
• The marking information is located at the rear or back of apparatus.  
Les informations de marquage est situé à l’arrière ou à l’arrière de  
l’appareil.  
This product incorporates copyright protection technology that is protected  
by U.S. patents and other intellectual property rights. Use of this copyright  
protection technology must be authorized by Rovi Corporation, and is intended  
for home and other limited viewing uses only unless otherwise authorized by  
Rovi Corporation. Reverse engineering and disassembly are prohibited.  
Customer Support: 1-888-999-4215  
GPX  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
24Class TV/DVD Combo  
Features  
Included  
23.6LED display  
Stand and 3 screws  
Remote control: requires 2 AAA batteries  
(included)  
DVD player: DVD, DVD R/RW  
CD player: CD, CD-R/RW, JPEG CD  
Resolution: 1920 x 1080  
Max color: 16.7 million  
Brightness: 300 cd/m2  
Contrast: 1000 : 1  
Response time: <5ms  
Viewing angle: H=170, V=160  
V-chip  
Closed captioning  
Electronic program guide  
Sleep timer  
Multi-language OSD  
RF input  
2 HDMI inputs  
2 RCA audio inputs  
VGA/PC video input  
3.5mm PC audio input  
2 Composite video inputs  
2 Component video inputs  
USB port  
Memory card reader  
AC power: requires an AC power cable  
(included)  
AC power cable  
* Please note, LCD panel specifications are subject to change without notice.  
4
GPX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
24” Class TV/DVD Combo                                                                                                                                         4  
Features  
Included  
Table of Contents                                                                                                                                                        5  
Introduction                                                                                                                                                                 6  
Setup                                                                                                                                                                              8  
Power  
Remote Power  
Connecting the Stand  
Television Setup                                                                                                                                                          9  
Connecting a TV Antenna  
Connecting Basic Cable  
Connecting a Set-Top Box  
Auto Scanning for Channels  
Television                                                                                                                                                                   10  
Channel List  
Saving a Channel as a Favorite  
Viewing Favorites  
Parental Controls  
Accessing the TV Menu  
Setting the Clock  
DVD                                                                                                                                                                              11  
Loading and Playing a Disc  
Programming a DVD  
Accessing the DVD Setup Menu  
Memory Card Reader                                                                                                                                              12  
Connecting a Memory Card  
Accessing the Connected Memory Card  
USB Port                                                                                                                                                                      13  
Connecting a USB Thumb Drive  
Accessing the Connected USB Thumb Drive  
Connecting Other Devices                                                                                                                                    14  
Connecting a Set-Top Box  
Connecting a Gaming Device  
Connecting a DVD Player or VCR  
Connecting a Computer  
Company Information                                                                                                                                            16  
International Support  
Contact Information  
Green Initiative  
Customer Support: 1-888-999-4215  
GPX  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
EJECT  
Press to eject  
the loaded  
disc.  
PLAY/PAUSE EJECT  
PLAY/PAUSE  
Press to play or  
pause a loaded  
disc.  
VOLUME  
Press to adjust Press to adjust  
the volume.  
CHANNEL  
MENU  
Press to view  
the television  
menu.  
SOURCE  
Press to adjust Press to power  
between  
the available  
sources.  
POWER  
the television  
channel.  
the television  
off or on.  
STEREO  
HEADPHONE  
JACK  
USB PORT  
RCA STEREO  
AUDIO INPUT 2  
COMPOSITE  
VIDEO INPUT 2  
DISC DRIVE  
COMPONENT  
VIDEO INPUT 2  
3.5mm PC AUDIO  
INPUT  
MEMORY  
CARD READER  
RCA STEREO  
AUDIO INPUT 1  
VIDEO INPUT  
1
USB  
AC IN  
Y
Pb  
Pr  
TV ANTENNA  
DRIVE  
COMPOSITE  
VIDEO INPUT 1  
RF INPUT  
COMPONENT  
VIDEO INPUT 1  
VGA/PC VIDEO  
INPUT  
HDMI INPUTS  
AC POWER  
INPUT  
SERVICE PORT  
Used for  
firmware  
upgrades.  
6
GPX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EJECT  
Press to eject a disc from the DISC DRIVE.  
NUMBER KEYPAD  
POWER  
EJECT  
POWER  
MUTE  
Press to turn the television off and on.  
DISPLAY  
Press to view the on-screen display.  
MUTE  
Press to mute the volume.  
16:9/4:3/FAV LIST  
Press to adjust the aspect ratio. Press to  
access your favorites list on the television.  
PICTURE  
Press to adjust the picture settings.  
PICTURE  
VOLUME  
Press to adjust the volume.  
SOUND  
SOUND  
SLEEP  
Press to adjust the sound settings.  
SOURCE  
Press to adjust the source.  
SLEEP  
Press to set the sleep timer.  
ARROW/ENTER  
Press to navigate DVD and system menus,  
and to make selections.  
ZOOM/CHANNEL LIST  
Press to zoom in or out on a loaded DVD.  
Press to view a list of available channels on  
the television.  
DVD  
16:9/4:3  
ZOOM  
CH LIST CHANNEL  
VOLUME FAV LIST  
CHANNEL  
DISPLAY  
Press to adjust the channel.  
SAP  
In TV mode, press to switch to an alternate  
audio option when supported.  
MENU  
SOURCE  
MENU  
Press to access the TV’s menu.  
ASPECT  
Press to adjust the aspect ratio.  
EXIT  
Press to exit the current on-screen menu.  
ENTER  
CC  
GUIDE  
Press to turn closed captioning off or on.  
Press to view the on-screen guide.  
SAP  
EXIT  
BACKWARD/FORWARD  
Press to search through an individual  
chapter or track.  
USB/SD  
Press to access USB and SD modes.  
CC  
ASPECT  
GUIDE  
USB/SD  
NEXT  
PREVIOUS/NEXT  
Press to skip between chapters or tracks on  
the loaded disc.  
STOP  
BACKWARD FORWARD PREVIOUS  
Press to stop a disc during play.  
PROG  
Press to program a loaded disc to play titles,  
chapters, or tracks in a specified order.  
DVD MENU  
Press to access the loaded DVD’s menu.  
STOP  
PROG  
PLAY/PAUSE DVD MENU DVD SETUP  
ANGLE  
TITLE  
A-B  
GOTO  
DVD SETUP  
Press to access the DVD setup menu.  
PLAY/PAUSE  
Press to play or pause a loaded disc.  
SUBTITLE  
AUDIO  
REPEAT  
GOTO  
SUBTITLE  
Press to adjust the current subtitle settings  
for the loaded DVD.  
Press to go to a specified title, chapter,  
track, or time on the loaded disc.  
REPEAT  
ANGLE  
Press to view alternate angles on supported  
DVDs.  
Press to repeat a title, chapter, track, or  
entire disc.  
AUDIO  
TITLE  
Press to view the title menu on the loaded  
DVD.  
Press adjust the current audio settings for  
the loaded DVD.  
A-B  
Press to create a repeating loop on a  
specified section of a loaded DVD.  
Customer Support: 1-888-999-4215  
GPX  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup  
Power  
Plug the attached AC cord into a standard AC  
power outlet to power the television.  
VIDEO INPUT  
1
USB  
DRIVE  
AC IN  
Y
Pb  
Pr  
TV ANTENNA  
Remote Power  
Requires 2, AAA size, batteries (included)  
Connecting the Stand  
Requires stand and 3 machine screws  
(all included)  
1. Insert a single machine screw through  
the bottom of the stand and up into the  
television. Tighten by hand using a philips-  
head screw driver.  
2. Insert the remaining two screws through  
the back of the stand and into the television.  
Tighten by hand using a philips-head screw  
driver.  
8
GPX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Television Setup  
Connecting a TV Antenna  
Connecting a Set-Top Box  
Requires a TV antenna (not included).  
Requires a Set-Top Box (not included).  
1. Connect a VHF, UHF, or HDTV antenna to the  
If your Set-Top Box has an HDMI Output:  
RF INPUT on the television.  
Connect the HDMI output on the Set-Top Box  
to the HDMI INPUT on the television using  
an HDMI cable (not included).  
The Auto Channel Scan must be run before any  
channels can be viewed on the television.  
2. Press the SOURCE button and switch to TV  
If your Set-Top Box has a Composite Video  
Output:  
mode.  
Connect the video output on the Set-Top  
Box to the COMPOSITE VIDEO INPUT on  
the television using an A/V RCA cable (not  
included). Connect the audio output on the  
Set-Top Box to the RCA STEREO AUDIO  
INPUT on the television.  
3. Press the MENU button.  
4. Use the ARROW buttons to select Channel in  
the on-screen menu. Press the ENTER button.  
5. Use the ARROW buttons to select Signal Type  
in the on-screen menu. Press the ARROW  
buttons to change the Signal Type to Air.  
If your Set-Top Box has a Component Video  
Output:  
6. Use the ARROW buttons to select Auto  
Channel Search in the on-screen menu. Press  
the ENTER button to automatically scan for  
available channels.  
Connect the component video output on  
the Set-Top Box to the COMPONENT VIDEO  
INPUTS on the television using a component  
RCA cable (not included). Connect the  
Connecting Basic Cable  
audio output on the Set-Top Box to the RCA  
STEREO AUDIO INPUT on the television.  
Requires a cable connection.  
1. Connect a cable to the RF INPUT on the  
After connecting your Set-Top Box:  
television.  
Press the SOURCE button to switch between  
TV, AV 1 or 2, YPbPr 1 or 2, HDMI 1 or 2, and  
VGA to match the connection used.  
The Auto Channel Scan must be run before any  
channels can be viewed on the television.  
2. Press the SOURCE button and switch to TV  
Auto Scanning for Channels  
mode.  
The Auto Channel Scan must be run before any  
channels can be viewed on the television.  
3. Press the MENU button.  
4. Use the ARROW buttons to select Channel in  
the on-screen menu. Press the ENTER button.  
1. Press the SOURCE button and switch to TV  
mode.  
5. Use the ARROW buttons to select Signal Type  
in the on-screen menu. Press the ARROW  
buttons to change the Signal Type to Cable.  
2. Press the MENU button.  
3. Use the ARROW buttons to select CHANNEL  
in the on-screen menu. Press the ENTER  
button.  
6. Use the ARROW buttons to select Auto  
Channel Search in the on-screen menu. Press  
the ENTER button to automatically scan for  
available channels.  
4. Use the ARROW buttons to select Auto  
Channel Search in the on-screen menu. Press  
the ENTER button to automatically scan for  
available channels.  
Customer Support: 1-888-999-4215  
GPX  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Television  
Channel List  
Parental Controls  
Press the CHANNEL LIST button on the remote  
to view a list of available channels on the  
television.  
1. In TV mode, press the MENU button.  
2. Use the ARROW buttons to select Parental  
Control in the on-screen menu. Press the  
ENTER button.  
If there are no channels in your channel list, you  
may need to re-run the Auto Scan for Channels.  
(see page 9)  
3. The default passcode for the parental lock is:  
0 0 0 0  
From the V-CHIP settings you can lock TV and  
movies that have specific ratings.  
Saving a Channel as a Favorite  
1. In TV mode, press the MENU button.  
Use the Front Panel Lock to lock the buttons on  
the television. (The remote will still work if the  
Front Panel Lock is checked)  
2. Use the ARROW buttons to select Channel in  
the on-screen menu. Press the ENTER button.  
3. Use the ARROW buttons to select Channel  
Setting in the on-screen menu. Press the  
ENTER button.  
Accessing the TV Menu  
1. In TV mode, press the MENU button.  
4. Use the ARROW buttons to select the  
Channel Number you want to save as a  
favorite.  
To exit the TV menu, press the EXIT button on  
the remote.  
Setting the Clock  
5. Use the ARROW buttons to select Favorite  
Channel. Press the ENTER button to save the  
selected channel as a favorite.  
1. In TV mode, press the MENU button.  
2. Use the ARROW buttons to select Setup in  
the on-screen menu. Press the ENTER button.  
Viewing Favorites  
1. In TV mode, press the FAVORITES LIST  
button on the remote to access your favorites  
list on the television.  
3. Use the ARROW buttons to select Clock in  
the on-screen menu. Press the ENTER button.  
4. Use the ARROW buttons to select your time  
2. Use the ARROW/ENTER buttons to highlight  
zone.  
and select a channel from the favorites list.  
5. Use the ARROW buttons to highlight Setup  
Time.  
6. Use the left and right ARROW buttons and  
ENTER button to adjust and save the date  
and time.  
10 GPX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DVD  
Loading and Playing a Disc  
1. Press the SOURCE button to switch to DVD  
mode.  
2. Insert a DVD or CD into the DISC DRIVE, label-  
side facing the rear of the TV.  
The loaded disc will begin playing  
automatically.  
3. If the loaded disc does not automatically  
play, press the PLAY/PAUSE button.  
Programming a DVD  
1. Follow the instructions for Loading and  
Playing a Disc.  
2. Press the PROGRAM button on the remote.  
3. Use the NUMBER KEYPAD and ARROW  
buttons to enter title (TT) and chapters (CH)  
from the loaded DVD in the order you want  
them to play.  
Disc title and chapter information can be  
obtained by pressing the DISPLAY button  
during DVD playback.  
4. Press the PLAY/PAUSE button or use the  
ARROW buttons to highlight the on-screen  
PLAY button and press ENTER to begin  
playing the programmed DVD.  
Accessing the DVD Setup Menu  
1. To access the DVD Setup Menu, press the  
DVD SETUP button on the remote.  
To exit the DVD setup menu, press the DVD  
SETUP button.  
Customer Support: 1-888-999-4215  
GPX 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Memory Card Reader  
Connecting a Memory Card  
1. Load an SD, MS, or MMC memory card into  
the MEMORY CARD READER as shown in  
the image to the right.  
Accessing the Connected Memory Card  
1. Follow the instructions for Connecting a  
Memory Card.  
2. Press the SOURCE button to switch to DVD  
mode.  
3. Press the USB/SD button on the remote to  
switch to CARD mode.  
4. Use the ARROW/ENTER buttons to select  
and play content from the connected  
memory card.  
12 GPX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
USB Port  
Connecting a USB Thumb Drive  
1. Connect a USB thumb drive to the USB PORT  
as shown in the image to the right.  
Accessing the Connected USB Thumb Drive  
1. Follow the instructions for Connecting a USB  
Thumb Drive.  
2. Press the SOURCE button to switch to DVD  
mode.  
3. Press the USB/SD button on the remote to  
switch to USB mode.  
4. Use the ARROW/ENTER buttons to select  
and play content from the connected USB  
thumb drive.  
Customer Support: 1-888-999-4215  
GPX 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting Other Devices  
Connecting a Set-Top Box  
Connecting a DVD Player or VCR  
You will need: a set-top box, composite  
and RCA stereo cables or component and  
RCA stereo cables or an HDMI cable. (not  
included)  
You will need: a DVD player or VCR,  
composite and RCA stereo cables or  
component and RCA stereo cables or an  
HDMI cable.  
Connect the set-top box’s audio and video  
outputs to the corresponding audio and  
video inputs on the television.  
Press the SOURCE button to switch between  
TV, AV 1 or 2, YPbPr 1 or 2, HDMI 1 or 2, and  
VGA to match the connection used.  
Connect the DVD player or VCR’s audio and  
video outputs to the corresponding audio and  
video inputs on the television.  
Press the SOURCE button to switch between  
TV, AV 1 or 2, YPbPr 1 or 2, HDMI 1 or 2, and  
VGA to match the connection used.  
Connecting a Gaming Device  
Connecting a Computer  
You will need: a gaming device, composite  
and RCA stereo cables or component and  
RCA stereo cables or an HDMI cable. (not  
included)  
Connect the gaming device’s audio and video  
outputs to the corresponding audio and  
video inputs on the television.  
Press the SOURCE button to switch between  
TV, AV 1 or 2, YPbPr 1 or 2, HDMI 1 or 2, and  
VGA to match the connection used.  
You will need: a PC with a VGA output, and a  
VGA cable. (not included)  
Connect the computer’s VGA output to the  
VGA/PC INPUT on the television.  
Power the television on and press the  
SOURCE button to switch to the VGA Mode.  
Audio from the connected PC can be input  
to the television through the TV’s PC AUDIO  
INPUT by using a 3.5mm audio cable (not  
included).  
14 GPX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Customer Support: 1-888-999-4215  
GPX 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Company Information  
International Support  
Green Initiative  
To download this User’s Guide in English,  
Spanish, or French, visit the support section at  
Para transferir esta guía de usuario en inglés,  
español, o francés, visite la sección de la ayuda  
Pour télécharger ce guide de l’utilisateur en  
anglais, espagnol, ou français, visitez la section  
Environmental Commitment to ‘Protect for Today  
and Sustain for Tomorrow’  
2009 marked the official launch of DPI, Inc.’s  
corporate campaign for a greener and cleaner  
world. DPI is building upon environmental  
initiatives introduced at all of their facilities  
to help formulate and sustain significant and  
important conservation efforts within its  
manufacturing and marketing communities.  
In addition to targeting and selecting energy  
efficient product features, and structuring ‘green  
officeprocedures, other initial program efforts  
include:  
Contact Information  
Phone:  
1-888-999-4215  
Email:  
Parts Email:  
Website:  
Reduction of all packaging sizes  
Recyclable plastics for clamshell packages,  
with a plan to eventually replace plastic with  
recyclable paper  
Recycled fiber board in place of the polyfoam  
in packing boxes  
Recycled plastics in place of the virgin  
material in product construction  
Copyright © 2010 Digital Products International (DPI, Inc.) | All other trademarks appearing herein are the property of their respective owners.  
Specifications are subject to change without notice  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Haier Dishwasher HDB18EB User Manual
Hans Grohe Plumbing Product 06091000 User Manual
Hasselblad Camcorder 3034216 User Manual
HP Hewlett Packard Flat Panel Television LC3260N User Manual
HP Hewlett Packard Graphics Tablet HP 61016A User Manual
HP Hewlett Packard Network Card EA833AA User Manual
HP Hewlett Packard Power Supply 6205B User Manual
HTC PDAs Smartphones AM171 User Manual
Husqvarna Chainsaw 1153137 49 User Manual
Husqvarna Tiller T 350 User Manual