Golden Technologies Wheelchair GP600 CC User Manual

Compass  
Owner’s Manual  
Compass  
Center-Wheel Drive Power Chair  
GP600 SS/GP600 CC  
401 Bridge Street, Old Forge PA 18518  
Tel: (800) 624-6374 Fax: (800) 628-5165  
Y O U R L I F E I N M O T I O N  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
Thank you for purchasing your Compass GP600 power chair. We are honored you have  
chosen Golden Technologies for your mobility needs.  
Compass Model GP600  
Standard Packing List:  
1 Owner’s Manual  
Base unit  
1 Seat  
2 Seat Arms  
1 Joystick Control  
1 Seat Belt  
1 Battery Charger  
FOR YOUR RECORDS  
Please fill in your Compass information below. This information will be useful in the  
event that you ever need to contact Golden Technologies, Inc. concerning your power chair.  
Your Compass  
Model __________________  
Date of Purchase _______  
Options ________________  
Serial Number _______________  
Body Color __________________  
Your Golden Technologies, Inc. representative or dealer  
Name ____________________________________  
Company ________________________________  
Address _________________________________  
Please remember to fill in and return your warranty registration card.  
DISCLAIMER  
We ask that you read this manual completely before operating your new Golden Compass.  
Golden Technologies, Inc. is not and cannot be held responsible for any damage or injury  
incurred due to improper or unsafe use of the Golden Compass GP600, power chair. Golden  
Technologies, Inc. specifically disclaims responsibility for any bodily injury or property  
damage that may occur during any use that does not comply with applicable federal, state,  
or local laws or ordinances.  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
CONTENTS  
INTRODUCTION …………………………………………………… 4-5  
SAFETY..............................................................……….. 5-9  
EMI/RFI ........................................................…….…….. 10  
SPECIFICATIONS…………………………………………………… 11  
ASSEMBLY…………………………………………………………… 12-16  
COMFORT SETTINGS…………………………………………….. 17-22  
OPERATION/DIAGNOSTICS ……………………………………. 23-29  
BATTERY CHARGING ……………………………………………. 30-31  
CARE AND MAINTENANCE …………………………………….. 32  
DISASSEMBLY ……………………………………………………… 33  
WARRANTY …………………………………………………………. 34-35  
REGISTRATION CARD …………………………………………… 36  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
INTRODUCTION  
Congratulations on the purchase of your new Compass power chair. The Center-wheel  
drive Compass combines cutting-edge technology with an attractive design that is also  
highly functional in today’s world. We at Golden Technologies, Inc. know that you have  
chosen a power chair that will give you years of dependable operation and also will enhance  
the quality of your life by providing you with the mobility to experience an active daily  
lifestyle.  
Even though your new Compass is both user-friendly and designed for maximum  
maneuverability in even the tightest spaces, we ask that you please read, understand and  
follow all of the instructions and suggestions in this manual before you operate your  
Compass for the first time. The safe use of your new power chair is very important to us.  
If you feel that you do not understand the instructions and suggestions presented in this  
owner’s manual, or if, for any reason, you do not feel capable of performing the activities  
necessary to assemble, disassemble, operate, or maintain your Compass please contact  
your local Golden Technologies, Inc. representative or call Golden Technologies, Inc.  
Technical Support Services at (800) 624-6374.  
Golden Technologies, Inc. cannot be held responsible for personal injury or property  
damage resulting from the unsafe or the improper use of any of our broad range of health  
and personal mobility products. Our Research and Development Department, our Quality  
Control Department, and our Engineering Department have used the latest product  
specifications and the latest product design information to produce this owner’s manual.  
Golden Technologies, Inc. reserves the right to implement changes into our product lines  
when those changes become desirable or necessary. If changes are implemented into our  
product line, there may be minor differences between the product you purchased and the  
illustrations and instructions in this owner’s manual.  
Please fill out and mail the enclosed warranty registration card on page 32. We at Golden  
Technologies, Inc. would appreciate hearing about the dependability of your Compass and  
about the convenience of mobility it has provided for you. We would also appreciate  
hearing about the service you received from your local Golden Technologies, Inc.  
representative.  
Golden Technologies, Inc.  
401 Bridge Street  
Phone:  
Fax:  
(570) 451-7477  
(570) 451-7494  
Old Forge, PA 18518  
Toll free: (800) 624-6374  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
INTRODUCTION  
ACCESSORIES for the Compass POWER CHAIR:  
A variety of accessories are available for your Golden Compass power chair. Please contact  
your Authorized Golden Technologies Dealer for more information or to order.  
• Cane Holder Tube  
• Oxygen Tank Holder  
• Cup Holder  
• Quad Cane Holder  
• Rear Basket  
• Safety Flag  
• Swing-Away Footrests  
(Optional)  
• Stump Support  
(Optional)  
• Elevating Leg Rests  
(Optional)  
• Power Chair Cover  
• Touch-up Paint  
• Deluxe Pack N’ Go  
• Swing-Away Joystick  
Bracket (Optional)  
• Walker Holder  
• Crutch Holder  
*Some accessories require a mounting bracket or mounting clips. Please check with  
your dealer to find out if the accessory you would like to order requires a mounting  
bracket or mounting clips.  
Safety Guidelines  
The symbols below are used in the owner's manual and/or on the product to identify  
warnings and to notify you of important safety information. Make sure you read and  
understand them completely.  
WARNING! Indicate(s) a hazardous situation which, if not avoided, could  
result in death or serious injury. This icon is represented as a black symbol on  
a yellow triangle with a black border.  
MANDATORY! Failure to perform mandatory actions can cause personal  
injury and/or equipment damage. This icon is represented as a white symbol  
on a blue dot with a white border.  
PROHIBITED! Indicate(s) an action(s) that should not be performed under any  
circumstance. Failure to adhere can cause personal injury and/or equipment  
damage. This icon is represented as a black symbol with a red circle and red  
slash.  
Safety Symbols  
The symbols below identify warnings, mandatory actions, and prohibited actions. They  
can be found in the owner’s manual and/or on the product. Make sure you understand  
all safety labels before operating the product. Do not remove safety labels from the  
product.  
Explosive conditions exist!  
Read and follow the  
owner’s manual!  
Indoor use only!  
Use only AGM or  
Gel-Cell batteries!  
Avoid transmitters!  
Hot surface!  
Pinch/Crush Hazard!  
Do not place into trash!  
Recycle  
Electrical hazard!  
Corrosive chemicals  
inside battery!  
Do not use  
personal  
electronic devices!  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
SAFETY  
Your Compass is a battery-operated personal mobility vehicle. Please exercise caution  
and consideration when you are operating it. Driving your Compass carefully and  
thoughtfully will help ensure your personal safety and the safety of other people.  
MANDATORY! Read and follow the owner’s manual before operating your  
power chair.  
NOTE: Before learning to operate your Compass , have your Golden Technologies, Inc.  
representative determine if it is advisable for you to practice getting on and off your  
Compass and operating it in the presence of an attendant.  
BEFORE GETTING ON YOUR Compass  
Check to be certain that the power is turned off. See “Operation” on pages 23-29.  
This will eliminate the possibility of accidentally activating the joystick and causing  
injury to yourself or to others.  
Check to be certain that your Compass is not in freewheel mode. See the  
“Operation” section on pages 23-29.  
Flip up the armrests.  
If your chair is equipped with leg rests, move them to the sides.  
If your chair is equipped with a footrest, flip it to the “up” position.  
GETTING ON YOUR Compass  
While being careful not to entangle yourself in the leg rests or the footrest, seat  
yourself comfortably and securely on the seat.  
Adjust the leg rests or flip down the footrest.  
Flip down or replace the armrests.  
Fasten the lap belt, if your chair is so equipped.  
GETTING OFF YOUR Compass  
Make certain that the power is turned off.  
Unfasten the lap belt, if your chair is so equipped.  
Flip up the armrests.  
Flip up the footrest, or move the leg rests to the sides.  
While being careful not to entangle yourself in the leg rests or the footrest, carefully  
stand and step away from the chair.  
MAXIMUM WEIGHT  
Your Compass has been rated to a maximum payload (passenger and anything else  
)  
being carried on the Compass of 300 pounds. Exceeding the maximum weight rating  
will void the warranty.  
Exceeding the maximum weight capacity will void your  
warranty and may result in injury to yourself and/or others.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
SAFETY  
DRIVING ON AN INCLINE  
Drive with caution when attempting to negotiate any incline, even handicap access  
ramps.  
Try to keep your Compass moving when climbing an incline. If you do come to a  
stop, restart and accelerate slowly and carefully.  
Always climb or descend a gradient by driving straight up or straight down the face  
of the slope.  
Do not traverse or drive across the face of a gradient.  
Do not attempt to negotiate an incline that is covered with snow, ice, cut or wet  
grass, leaves, or any other potentially hazardous material.  
Do not back down an incline.  
Do not try to descend or climb an incline that is greater than the maximum incline  
stated in the specifications section of this manual.  
If, while you are driving down a slope, your chair starts to  
move faster than you feel is safe, gently release the joystick and allow your  
Compass to come to a stop. When you feel that you again have control of your  
power chair, adjust the speed control to a lower setting then push the joystick  
forward and continue safely down the remainder of the slope.  
MEDICATION  
Always check with your physician to determine if any of the medications you are taking  
may affect your judgment and/or your ability to operate your Compass .  
Do not connect or allow anyone except an authorized  
Golden Technologies, Inc. representative to connect any electrical or mechanical  
device to your Compass . Unauthorized accessories will void the warranty and  
may cause injury.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
SAFETY  
SAFETY RULES  
Do not attempt to use your Compass on an escalator. Always use an elevator.  
Do not carry passengers on your power chair.  
Do not operate your Compass if it is not functioning properly.  
Use caution when driving on soft or uneven surfaces such as grass, gravel, and on  
decks where there is no railing.  
Never drive on the roadway, except when you must cross the street.  
Always cross streets at intersections and use the most direct route, making sure  
that your path is clear and that you are visible to motor traffic.  
It is not recommended to drive your Compass up or down a step or curb that is  
higher than 1 1/2 inches.  
Never back up or down a step or curb.  
Never operate your Compass while you are under the influence of alcohol.  
Do not operate or store your power chair where it will be exposed to rain, snow,  
mist, and below freezing temperatures.  
Do not operate your power chair on slippery, icy or salted surfaces.  
Never sit on your power chair when it is in freewheel mode and on an incline or  
decline.  
Do not modify your power chair in any way that is not authorized by Golden  
Technologies.  
Do not disassemble the tire. If disassembly is required, have your authorized  
Golden Compass dealer perform any necessary maintenance or repair.  
Do not attempt to inflate the tires of your Golden Compass . Your Golden  
is equipped with foam-filled flat free tires that do not require inflation.  
Compass  
Never sit on your Compass when it is being transported.  
Always fasten down your Compass securely with an approved tie-down system while  
transporting your power chair.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
SAFETY  
Please be sure to follow this important warning when transferring onto or off of the  
Golden Compass power wheelchair:  
NEVER TRANSFER ONTO OR OFF OF THIS POWER WHEELCHAIR USING THE  
SEAT BACKREST FOR SUPPORT DURING TRANSFER. THE SEAT BACK MAY FOLD  
DOWN AND MAY CAUSE YOU TO LOSE YOUR BALANCE AND COULD RESULT IN  
PERSONAL INJURY.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
EMI/RFI  
The rapid development of electronics, especially in the area of communications, has  
saturated our environment with electromagnetic (radio) waves that are emitted by  
television transmitters, cellular phones, citizen’s band radios (CBs), amateur radios  
(ham radios), wireless computer links, microwave transmitters, paging transmitters,  
etc. These electromagnetic (EM) waves are invisible and increase in strength the closer  
one gets to the source of transmission. When these energy waves act upon electrical  
devices and cause them to malfunction or to function in an erratic or uncontrolled  
manner, they are referred to as Electromagnetic Interference (EMI) or Radio Frequency  
Interference (RFI).  
EMI/RFI AND YOUR Compass  
All electrically powered vehicles, including power chairs are susceptible to EMI/RFI.  
This interference could result in abnormal, unintended movement of a power  
wheelchair.  
Unintended movement or brake release could cause an accident  
or injury.  
The FDA has determined that each make and model of power chair can resist EMI/RFI  
to a certain level. The higher the level of immunity, the greater the degree of protection  
from EMI/RFI measured in volts per meter (V/m). The FDA has also determined that  
current technology is capable of providing 20 V/m of immunity to EMI/RFI, which  
would provide useful protection against common sources of interference. This product  
has been tested and has passed an immunity level of 20 V/m.  
EMI/RFI RECOMMENDATIONS  
PROHIBITED! Do not turn on or use hand-held personal electronic  
communication devices such as cellular phones, walkie-talkies, and CB  
radios while your power chair is turned on.  
Be aware of any nearby transmitters (radio, television, microwave, etc.) on your  
intended route and avoid operating your chair close to any of those transmitters.  
Turn off the power if your Compass is going to be in a stationary position for any  
length of time.  
Be aware that adding accessories or components or modifying your power chair may  
make it more susceptible to EMI/RFI.  
If unintended movement or brake release occurs, turn your power chair off as soon  
as it is safe to do so.  
Report all incidents of unintended movement or brake failure to your Golden  
representative or to Golden Technologies, Inc. at (800) 624-6374.  
Turn off your power chair as soon as it is safely possible if  
unintended or uncontrollable motion occurs or if unintended brake release  
occurs.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
SPECIFICATIONS  
Model  
GP600 SS  
K0822  
GP600 CC  
K0823  
6 degrees  
300lbs.  
5 mph  
20 miles  
3.5”  
Medicare Code  
Maximum Incline  
Weight Capacity  
Maximum Speed  
Operating Range1  
Ground Clearance  
Turning Radius  
Type Batteries  
Colors  
6 degrees  
300 lbs.  
5 mph  
20 miles  
3.5”  
20 "  
20 "  
2-U1 or 2-NF22  
Red, Blue  
Off Board  
2-U1 or 2-NF22  
Red, Blue  
Off Board  
Charger  
Dynamic Shark  
50 Amp  
Dynamic Shark  
50 Amp  
Controller  
Remote  
Remote  
Dimensions:  
Length  
38.5"  
24.5"  
38.25” – 42.75”  
45.25” – 53.75”  
17.75” – 22.25”  
10  
38.5"  
24.5"  
38.25” – 42.75”  
45.25” – 53.75”  
19.75” – 24.25”  
10  
Width (outside of tires)  
Height (ground to top of back of seat)  
Height (ground to top of back of headrest)  
Ground to Top of Seat  
Number of Seat Height Positions  
Size of Increments  
0.5”  
0.5”  
Weight of Unit: (assembled)  
Total Weight with U1 Batteries  
Total Weight with NF22 Batteries  
Base  
Seat Arms  
Seat (18 X 18 Solid Pan Seat)  
Seat (18 X 18 Captain's Chair Seat)  
182 lbs  
212 lbs  
92 lbs  
14 lbs  
32 lbs  
185 lbs  
215 lbs  
92 lbs  
14 lbs  
35 lbs  
U1 - 22 lbs  
NF22 - 37 lbs  
U1 - 22 lbs  
NF22 - 37 lbs  
Batteries  
Tires:  
Center Drive Wheels (2)  
Casters (4)  
Flat Free  
Flat Free  
10”  
10”  
6”  
6”  
Standard Seat:  
Back Height-no headrest  
Back Height with headrest  
Width x Depth  
Color  
Captain’s Van/Pan  
23”  
Captain’s Highback  
21”  
30.5” – 34.5”  
28.5” – 32.5”  
16” x 16”, 18” x 18”, 20” x 2016” x 16”, 18” x 18”, 20” x 20”  
Coffee/Sand, Charcoal/Gray Coffee/Sand, Charcoal/Gray  
Electric Rise Seat (Option)  
Footrest:  
Yes  
Yes  
Height adjustable  
Angle adjustable  
Warranty:  
3" - 7”  
0 – 35 degrees  
3" - 7”  
0 – 35 degrees  
Frame  
Lifetime  
13 months  
13 months  
Lifetime  
13 months  
13 months  
Drive Train  
Electronics2  
1. Battery range will vary due to rider weight, drive surface, and terrain.  
2. Electronics warranty excludes batteries.  
Literature is current at the time of printing. Golden Technologies reserves the right to make changes to the product  
or literature at any time.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
ASSEMBLY  
Your Compass is shipped partially disassembled in order to maximize the protection  
of all its parts during the shipping process. Please follow the instruction below to  
quickly and easily assemble the power chair for your use.  
You will need only basic tools. If you do not have the required tools,  
or if you do not feel capable of safely assembling your power chair, please contact  
your local Golden Technologies, Inc. representative.  
Main Components  
1. Frame with power module, controller cable & connectors for battery cables  
2. Battery box cover (Two – one for U1 batteries, one for NF22 batteries)  
3. Seat assembly  
4. Joystick  
5. Batteries (Two – U1 or NF22)  
Seat Assembly  
Motor Shroud  
Battery Box Cover  
Caster Wheel  
Fenders  
Caster Arm Shroud  
Joystick  
Batteries  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
ASSEMBLY  
JOYSTICK INSTALLATION  
1. Position the joystick on the joystick bracket. Match the holes in the joystick with the  
holes in the bracket. See figure 1.  
2. Insert the 4 Allen-head screws with lock washers through the bracket and into the  
holes in the joystick.  
3. Use an Allen wrench to tighten the screws.  
4. Connect the joystick cable to the controller cable. See figure 2.  
5. Use the provided Velcrotie-wraps and under arm clip to secure the controller cable  
to the armrest bracket.  
Allen-head screws  
Joystick Bracket  
Figure 1  
Joystick Cable  
Figure 2  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
ASSEMBLY  
SEAT REMOVAL/INSTALLATION  
The standard (18x18) seat assembly weighs about 49 pounds.  
Please ask for help if you do not feel capable of safely lifting that much weight.  
Removal of arms will significantly reduce the weight of seat.  
Be sure the seat is correctly installed and locked before operating  
your power chair.  
Never pull on the arms or use them as a handle to move the power  
chair as they could inadvertently pull out of the receiver bar causing injury.  
REMOVAL  
1. Disconnect the controller cable from the joystick. “Unclip” from arm and remove  
Velcrotie-wraps. See figure 2 on page 13.  
2. Lift the front and rear seat lock handles and slide the seat until all (4) of the seat  
guides are out of the receivers.  
INSTALLATION  
The seat can be installed from either side of the power chair.  
1. To install the seat, align the seat guides (front and rear) with the seat receivers  
(front and rear).  
2. Slide the seat towards the center of the power chair until the seat locks securely  
in place. The front and rear locks must engage.  
3. Reconnect the controller cable to the joystick cable.  
Rear Seat  
Lock Handle  
Front Seat  
Lock Handle  
Front Seat  
Lock Handle  
Figure 3  
Figure 4  
Seat Locking  
Handle  
Rear Seat  
Lock Handle  
Seat Height & Angle  
Adjustment Pins  
Seat Guides  
Seat Receiver  
Figure 5  
Figure 6  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
ASSEMBLY  
Accessing the batteries  
After removing the seat, locate the (2)  
“Battery Box Cover Locks”.  
Depress both locks and lift the cover.  
Note: On the inside of the battery box  
cover there is a battery connection  
diagram.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
ASSEMBLY  
BATTERY INSTALLATION  
The batteries weigh 24 to 39 pounds each (depending on type).  
Please ask for help if you do not feel capable of safely lifting that much weight.  
Figure 7  
Figure 8  
Figure 9a  
Figure 9b  
Make certain that the controller power is turned off and that the chair  
is NOT in freewheel mode before attempting to perform assembly or disassembly.  
1. Place the batteries in the battery box. Be certain to position the terminals on each  
battery toward the front of the unit as shown in Figure 7. Secure the batteries in  
place using the hook and loop straps.  
2. Use the screws, washers, and nuts provided to connect the positive (red booted)  
connector of each cable to the positive (+) terminal of each battery. See figure 8.  
3. Use the screws, washers, and nuts provided to connect the negative (black booted)  
connector of each cable to the negative (-) terminal of each battery.  
4. Connect the connectors of each battery cable to the corresponding connector on the  
main wire harness. See figure 9a for NF22, figure 9b for U-1.  
5. Cover the battery terminals with the protective caps provided. See figure 9a for NF22,  
figure 9b for U-1.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models GP600 SS, GP600 CC  
Revised 052313  
COMFORT SETTINGS  
You may be spending a great deal of time on your Compass . To provide you with the  
maximum seating comfort, Golden Technologies, Inc. has designed this power chair to  
incorporate the following adjustments for operator comfort.  
COMFORT SETTINGS  
1. Seat height  
5. Footrest height  
6. Extending the footrest  
7. Armrest angle  
9. Joystick bracket length  
10. Armrest width  
2. Headrest height  
3. Backrest angle  
4. Footrest angle  
8. Armrest height  
Make certain that the power to your Compass is turned off  
before making any adjustments, to eliminate the risk of the joystick being  
accidentally bumped and activating the power chair.  
If you do not feel capable of safely making these adjustments, please  
contact your local Golden representative.  
Seat height adjustment  
The seat frame is a 4-post design that is adjustable in height and seating angle.  
Adjustment is made by removing ball detent pins, raising or lowering seat posts to  
desired height/angle and re-installing the ball detent pins.  
*Front/Rear height difference can be 3 inches.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
COMFORT SETTINGS  
Adjusting the seat with a front to rear angle  
Bottom of  
Seat  
Seat  
Guide  
Adjusting  
Bolts  
Loosen seat guide adjusting bolts using a 6mm Allen wrench provided in the charger bag  
and a pair of pliers or a 13mm open end wrench. Place the seat receivers in the lowest  
position and insert the ball detent pins through the towers and seat receiver legs. Leave  
the seat guide adjusting bolts loose. Slide the seat into the receivers, adjust seat to the  
desired height and angle using the (4) detent pins. Leave the seat in the seat receivers  
and tighten the seat guide adjusting bolts. This process is more easily accomplished with  
two people. Note: seat receivers must be 2” higher when using NF22 battery cover.  
Front Seat Locking  
Handle  
Seat Guides  
Seat  
Tower  
Seat Angle  
Adjusting Pins  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
COMFORT SETTINGS  
HEADREST HEIGHT ADJUSTMENT  
1. Push and then release the clamp on the left post of the headrest while you are pulling  
up or pushing down on the head rest. See figure 10.  
2. The headrest will “click” to a stop in one of the preset positions.  
3. Repeat step 1 until the headrest is at the desired height.  
Backrest Angle  
Adjustment Lever  
Headrest Clamp  
Figure 10  
Figure 11  
BACKREST ANGLE ADJUSTMENT  
NOTE: The backrest can be folded down to minimize chair height during transport.  
1. Pull up on the adjustment lever (see figure 11) and push against the backrest until the  
backrest is in the desired position.  
2. Release the lever.  
3. To return the backrest to the upright position, pull up on the lever and move the  
backrest to the desired position.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
COMFORT SETTINGS  
FOOTREST ANGLE ADJUSTMENT  
1. Fold the footrest upward for easy access to the angle adjustment bolt. See figure 12.  
2. Use a wrench to turn the adjustment bolt counter-clockwise to increase the footrest  
angle.  
3. Use a wrench to turn the adjustment bolt clockwise to decrease the footrest angle.  
Footrest Angle  
Adjustment Bolt  
Figure 12  
FOOTREST HEIGHT ADJUSTMENT  
1. Remove front cover.  
2. Use an Allen wrench to remove the bolts indicated in figure 13.  
3. Slide the footrest to the desired height.  
4. Align the bolt holes in the footrest and the footrest bracket.  
5. Install and tighten the bolts.  
Footrest Height  
Adjustment Bolts  
Figure 13  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
COMFORT SETTINGS  
EXTENDING THE FOOTREST  
Refer to the pictures below.  
1. Insert a 5mm Allen wrench from the top side into the (2) adjustment screws.  
2. Place a 10mm wrench on the backside onto the (2) nuts and loosen the (2) footrest  
adjustment screws.  
3. Slide the footrest plate to the desired position and tighten the adjustment screws.  
NOTE: The maximum extended length is not at the end of the slots.  
Footrest  
Adjustment  
Nuts (10mm)  
Footrest  
Adjustment  
Screws (5mm)  
Top View  
Bottom View  
ARMREST ANGLE ADJUSTMENT  
Refer to the picture below.  
1. Lift armrest up.  
2. Turn jam nut counter-clockwise to loosen.  
3. Turn the adjustment bolt using a 6mm Allen wrench to raise or lower the armrest-  
angle. Turning the bolt counter-clockwise will raise the angle. Turning the bolt  
clockwise will lower the angle. Turn until desired angle is reached.  
4. Re-tighten jam nut by turning clockwise.  
5. Repeat steps 1-4 on the other armrest.  
Adjustment Bolt  
(6mm Allen)  
Jam Nut  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
COMFORT SETTINGS  
Joystick Holder  
Joystick Bracket  
Armrest Height  
Adjustment Knob  
Joystick Position  
Set Screw  
Figure 14  
Figure 15  
Armrest Width  
Adjustment Knobs  
Figure 16  
ARMREST HEIGHT ADJUSTMENT  
1. Loosen “Armrest Height Adjustment Knob” (Figure 14) until you can pull it outward.  
Note: The knob is retained in its housing with a spring.  
2. While keeping the knob pulled, raise or lower the armrest to the desired position then  
release the knob. After releasing the knob, you may have to raise or lower the  
armrest until it aligns with the nearest locking position.  
3. Tighten the height adjustment knob.  
JOYSTICK BRACKET LENGTH ADJUSTMENT  
1. Loosen the setscrew that adjusts the joystick position. See Figure 15.  
2. Slide the joystick bracket in or out of the joystick holder to desired position.  
3. Tighten the setscrew.  
ARMREST WIDTH ADJUSTMENT  
1. Loosen the adjustment knobs at the rear of the seat. See Figure 16.  
2. Slide the arms in or out.  
3. Tighten the adjustment knobs. See Figure 16.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
OPERATION  
Your Compass is simple to operate. However, for your safety and the safety of others,  
Golden Technologies, Inc. recommends that you carefully read and understand the  
following operating instructions. We also recommend that you practice operating your  
Compass in an area free of any obstacles. Once you have gained confidence in your  
ability to control your power chair, you will more easily be able to operate it in normal  
daily conditions.  
Before turning on the power of your Compass , take note of your  
environment and set your speed control accordingly. (See “The Speed Control Buttons”  
Figure 17) For indoor driving, we recommend that you select the lowest speed setting.  
For outdoor driving, we recommend that you select a speed setting at which you feel  
comfortable, safe, and in control of your power chair. Familiarize yourself with the  
features of your Compass described below and follow the instructions to safely operate  
your power chair.  
DRIVING: The Joystick On/Off Switch  
Push the on/off button to turn on the power to your Compass . See figure 17.  
The 8 LEDs (Light Emitting Diodes) will flash once and a number of LEDs will remain  
depending on the state of the battery charge.  
The LED array, that functions as the battery charge gauge, will light up. See “Battery  
Charging” on page 30-31.  
Pressing the on/off button again will turn off the power to your Compass .  
Speed Control - Slower  
Battery Charge LED  
Array  
On/Off Button  
Joystick  
Speed Setting LED  
Horn Button  
Array  
Speed Control - Faster  
Figure 17  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
OPERATION  
The Speed Control Buttons  
These buttons provide you with a way to control the maximum speed of your Compass .  
Press the “turtle” button repeatedly to set your chair’s speed to the slowest setting  
(recommended for indoor operation). Slowest speed is indicated by one (1) lit LED  
section on the speed indicator scale.  
Press the “rabbit” button repeatedly to set your chair’s speed to its highest setting.  
Highest speed is indicated by five (5) lit LED sections on the speed indicator scale.  
NOTE: For your safety, the controller automatically sets the reverse speed, acceleration,  
and deceleration in proportion to the speed control setting.  
The Joystick  
The joystick (see figure 17 on previous page) controls the speed (up to the maximum limit  
set by the speed control knob) and direction of your power chair.  
NOTE: When you are not pushing on the joystick, or when you release the joystick, the  
joystick will automatically return to the neutral position, the chair will decelerate, as the  
electromagnetic brakes are applied, and come to a smooth stop.  
Pushing the joystick away from the neutral (center) position will move your  
Compass™ in the direction that the joystick is pushed.  
The farther forward or backward you push the joystick, the faster your power  
chair will go.  
To operate your power chair, gently push the joystick in the direction in  
which you want to travel.  
Gentle operation of the joystick will provide you with smoother changes in speed  
and direction.  
Sharp or jerky operation of the joystick will result in quick and drastic changes in  
direction and speed.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
OPERATION  
The Joystick Display  
The joystick display (see figure 17 on page 23) is a multifunctional visual display.  
This display provides three types of information.  
1. On/Off status  
2. Battery charge level  
3. Fault diagnostics  
1. On/Off Status  
When you turn on the power to your Compass , the LED array will light up  
(see figure 17 on page 23).  
If the LED array is not lit, the controller and the power chair are not in  
operating mode.  
2. Battery Charge Level  
The joystick LED array is composed of six LED’s.  
Two red  
Two amber  
Four green  
When all eight (8) LEDs are lit continuously, there is a full charge on the batteries. As  
you use your power chair and the batteries discharge, LEDs in the array will begin to  
turn off in descending order. A single lit red LED indicates the lowest state of operable  
charge on the batteries. The batteries should be charged immediately.  
NOTE: To ensure a dependable battery charge, we recommend that you charge the  
chair’s batteries overnight. Doing this will prolong the life of the batteries and spare you  
loss of operational power while you are using your chair normally.  
3. Fault Diagnostics  
The joystick LED array is also designed to help you diagnose any problems with the  
electrical components of your power chair. The LED array does this by flashing on  
and off in a coded sequence.  
See the table on the following page to see the list of diagnosable problems and the  
flash code sequence.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
OPERATION/DIAGNOSTICS  
For Compass Units with the SHARK Controller  
Flash codes indicate the nature of an abnormal condition directly from the SHARK  
Information Gauge. Without the use of any servicing tools, the condition can be  
simply diagnosed.  
Flash  
Code  
Description  
User Fault  
Recommended Action  
Possible stall timeout or user error. Release  
the joystick to neutral and try again.  
1
Check the batteries and cabling. Try charging  
the batteries. Batteries may require replacing.  
Check the right motor, connections and  
cabling.  
Check the left motor, connections and  
cabling.  
2
3
Battery Fault  
Right Motor Fault  
Left motor fault  
4
Check the right park brake, connections and  
cabling.  
Check the left park brake, connections and  
cabling.  
Check the SHARK Communications Bus con-  
nections and wiring. Replace the Control Unit  
5
Right park brake fault  
Left park brake fault  
SHARK Control Unit Fault  
6
7
Check SHARK connections and wiring.  
Replace the Power Module.  
SHARK Power Module  
Fault  
8
Check SHARK connections and wiring.  
Replace the SHARK Control Unit.  
Check all connections and wiring. Consult a  
service agent.  
SHARK Communications  
Fault  
9
10  
Unknown Fault  
The SHARK modules are not user serviceable. Do not attempt to repair Shark  
modules.  
Note that joystick OONAPU (Out Of Neutral At Power Up) is not a fault. Simply by  
removing your hand from the joystick and allowing it to return to the neutral position,  
the fault will immediately clear. If the condition persists after removing your hand, the  
joystick may be damaged. Consult a Service agent.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
OPERATION  
Figure 18  
Figure 19  
FREEWHEEL MODE  
To disengage the gears and put your power chair in freewheel mode, turn the  
freewheel levers as shown. See figure 18.  
To re-engage the gears and take your chair out of freewheel mode, turn the levers as  
shown. See figure 19.  
Never put your power chair in freewheel mode when it is on a  
slope or incline of any type.  
Never put your power chair in freewheel mode while you are  
operating your power chair.  
THERMAL ROLLBACK  
Your Compass is equipped with a safety system. A microprocessor monitors the  
operating temperatures of the controller. In the event of excessive heat occurring in the  
controller, the controller will decrease the speed of your chair. This is done to reduce the  
load on the electrical system and allow the components to dissipate heat. The controller  
will automatically set the chair’s speed back to full normal when the operating  
temperature returns to normal levels.  
THE MAIN CIRCUIT BREAKER  
The main circuit breaker is another safety feature incorporated into your Compass .  
This device monitors the amount of current being drawn from the batteries when the  
chair is in use. When the motors are heavily strained and too high a current draw is  
being placed on the batteries, the main circuit breaker will trip and bring your chair to  
a stop.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
OPERATION  
Reset Button  
(Circuit breaker)  
Figure 20  
Reset Button  
If the main circuit breaker trips, please wait for approximately 1 minute and then push  
the reset button to reset the main circuit breaker. See figure 20.  
NOTE: Usually, the thermal rollback feature is more sensitive than the main circuit  
breaker. We recommend that you turn off the power to the chair and wait for five  
minutes when the chair suddenly loses speed or power. Doing so will allow the  
overheated electrical components to cool to their normal operating temperatures.  
SWING-AWAY DESK ARM  
Your Compass is equipped with a swing-away desk arm that provides you with the con-  
venience of positioning your chair close to a work surface such as a table or desk.  
To swing the desk arm simply push on the side of the joystick until the joystick swings to  
the retracted position. See figures 21, 22, and 23.  
Figure 21  
Figure 22  
Figure 23  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
OPERATION  
POWER SEAT (Requires an optional 75 amp controller/joystick with seat control)  
Your power chair may be equipped with a power seat. The power seat actuator is  
designed to raise or lower the seat with minimal effort by the user. The power seat switch  
is located on the joystick control. See figure below. (Power Seat Mode Activated)  
ON/OFF  
SWITCH  
Power Seat Switch  
Lower Speed (Rabbit)  
Raise Speed (Rabbit)  
Joystick control panel  
Before attempting to operate the power seat for the first time,  
make sure your power chair is level and stationary and the speed adjustment dial is  
set to its slowest (turtle) setting.  
To operate the power seat:  
1. Press the on/off button to power on the chair.  
2. Press the power seat button to activate the power seat.  
3. Press the joystick lever forward to raise the seat. Release the lever when you have  
reached your desired height or upon reaching the highest position.  
4. Pull the joystick lever back to lower the seat. Release the lever when you have reached  
your desired height or upon reaching the lowest position.  
5. Press the power seat switch to return to drive mode.  
How the Power Seat Functions:  
By elevating the power seat to approximately one-half its maximum height your power  
chair’s speed will be limited to half the speed dial setting. If the power seat is elevated to  
approximately three-quarters its maximum height, the power chair will not move if the  
throttle control lever is pressed. The power seat must be lowered to slightly under, three-  
quarters of its maximum height in order to drive the power chair again. The power chair  
cannot be driven at full speed until the power chair’s seat is lowered to under one-half its  
maximum height.  
Problem Solving:  
If you encounter an instance where after using the power seat feature that the power  
chair will not run, try lowering your seat. Depending on how high the power seat is  
raised, your power chair’s speed will be reduced or the power chair may stop operating  
and give a fault code. For details, refer to the above section “How the Power Seat  
Functions.”  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
BATTERY CHARGING  
You must use only the charger that is supplied with your  
Compass . The use of any other charger on this power chair will void the warranty.  
Using unauthorized chargers may also result in severe damage to the batteries and/ or  
damage to the chair. Using the wrong charger may also be a hazard.  
Operational Range  
Depending on the use, the terrain, and the driving conditions, the batteries of your  
Compasswill provide fifteen to twenty miles of operation (with the use of NF22  
batteries).  
WARNING! Corrosive chemicals contained inside battery.  
Explosive battery conditions exist.  
WARNING! Charger surface can become HOT.  
Electrical hazard!  
BATTERIES AND CHARGING  
Battery maintenance is the most important part of maintaining your power chair.  
Keeping the batteries fully charged helps to extend battery life. Use the following  
guidelines to help keep your batteries in optimum condition.  
IMPORTANT! New batteries MUST be fully charged prior to the initial use of your power  
chair.  
Charge new batteries for 12 hours even if the battery gauge already shows a full  
charge. This is to condition your new batteries for maximum performance.  
• For daily use, keep batteries fully charged. We recommend that you plug in the off-  
board charger after each use and charge 6-8 hours.  
“For best results please charge your batteries overnight after every use.”  
• If you are not going to use the power chair for more than a week, fully charge the  
batteries and then disconnect them from the power chair. Refer to page 16.  
Charging Guidelines Checklist to Maximize Battery Life  
Use only the automatic off-board charger supplied for all routine charging.  
Never use an automotive or wet type charger.  
Avoid deep discharges and never drain the batteries completely.  
Do not leave batteries in a low state of charge for extended periods. Charge a  
discharged battery as soon as possible.  
Fully recharge batteries regularly.  
Always store batteries fully charged.  
Check stored batteries once a month and recharge as necessary.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
BATTERY CHARGING  
CHARGING THE BATTERIES  
Your Compass’s charging system is designed for your safety and for your convenience.  
Follow the steps below to recharge the batteries.  
1. Position your Compass close to a standard wall electrical outlet.  
2. Turn off the power on the joystick.  
3. Remove the charger from the SEAT POCKET. See figure 24.  
4. Insert the matching charger plug into the joystick’s charging socket that is located at  
the front of the joystick. See figure 25.  
NOTE: MAKE SURE THE STANDARD ELECTRICAL OUTLET YOU ARE USING IS NOT  
CONTROLLED BY A LIGHT SWITCH CAUSING THE CHARGER TO SHUT OFF WHEN  
IT IS ACTIVATED.  
5. Insert the plug at the other end of the charger power cord into a standard electrical  
wall outlet.  
6. Disconnect the charger power cord from the wall outlet and from the joystick charging  
socket when the batteries are fully charged.  
NOTE: The batteries will be fully charged in approximately eight hours. A full charge is  
indicated when the green light on the battery charger side panel turns on and all 8  
joystick LEDs are lit when joystick is turned on.  
Charging Socket  
Figure 24  
Figure 25  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
CARE AND MAINTENANCE  
Your Compass is designed to require minimal maintenance. We recommend that you  
periodically check the following:  
Tire Tread: Regularly visually inspect the tire tread. If the remaining tread is less than  
1/32 of an inch, have your local Golden representative replace the worn tires.  
Motor Brushes: Have your local Golden representative inspect the motor brushes once a  
year.  
Joystick and Controller: Protect the joystick and controller from adverse weather  
conditions. Moisture will damage the controller and void your power chair’s warranty.  
Battery Terminals: Regularly inspect the condition of the battery terminals. Make  
certain that they are not corroded. Also check to see that the terminals are securely  
tightened.  
Cleaning: Use only a water-dampened soft cloth to clean the ABS shroud. The shroud  
has a protective coat that is very easy to maintain.  
Do not use free-flowing water to clean your Compass . Water  
and extreme temperatures are the main elements that can adversely affect your  
power chair and its performance.  
Water, Rain, Sleet, and Snow  
Water, in any form, will cause electronic malfunction or corrosion of the electrical  
components, connections, and the chair frame.  
Temperature  
At extremely low temperatures, the batteries of your power chair may freeze, pre-  
venting your Compass from operating.  
At extremely high temperatures, your power chair may operate at slower speeds due  
to the controller’s thermal rollback feature that is designed to prevent damage to the  
motors and to the other electrical components of the chair.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
DISASSEMBLY  
Make certain that the controller power is turned off and that  
the chair is NOT in freewheel mode before attempting to perform disassembly.  
SEAT REMOVAL  
1. Disconnect the joystick cable from the joystick. See figure 2 on page 13.  
2. See page 14 to complete the removal.  
The standard (18x18) seat assembly weighs about 49 pounds.  
Please ask for help if you do not feel capable of safely lifting that much weight.  
Removal of arms will significantly reduce the weight of seat.  
BATTERY REMOVAL for Transportation  
After removing the seat and battery box cover:  
1. Disconnect the battery connectors and unfasten battery straps. See figures 7 and 9  
on page 15.  
2. Use the battery handles to lift the batteries out, one at a time.  
The batteries weigh 25 to 39 pounds each (depending on type).  
Please get help if you do not feel capable of safely lifting that much weight.  
For Replacement  
After removing the seat and battery box cover:  
1. See pages 10 and 11.  
2. Disconnect the battery connectors and unfasten battery straps.  
3. Use the battery handles to lift the batteries out, one at a time.  
4. Remove the protective caps from the battery terminals.  
5. Disconnect the positive (+) battery cables from the battery terminals, one at a time.  
6. Disconnect the negative (-) battery cables, one at a time.  
7. Install new batteries. See BATTERY INSTALLATION on page 15 or see the instructions  
on the inside of battery box lid and follow the steps.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
Consumer Limited Warranty  
Power Wheelchairs  
The following warranty is granted only to the INITIAL Consumer who has purchased our product and  
commences on the Date of Purchase by the Consumer from an Authorized Golden Technologies’  
Provider. The Consumer must have a warranty registration card filed with Golden Technologies to  
receive service. This warranty supersedes all previous warranties for all power chair models.  
The warranty covers the following power wheelchair models unless otherwise noted:  
Alanté Jr GP200  
Alanté GP201  
Compass GP600  
Compass GP601  
Compass TRO GP615  
Compass GP620  
Alanté DX GP204  
Alanté LT GP215  
Compass Sport GP605  
Alanté Sport GP205  
LiteRider PTC GP160  
Limited Lifetime Warranty:  
In the event of defective materials or workmanship, Golden Technologies will repair or replace at  
our option any of the following structural frame components found to be defective by an  
authorized Golden Technologies representative:  
Steel Frame*  
Frame Welds*  
Seat Post*  
*The GP615TRO, GP620, GP204, GP215, GP160 and the GP205 are warranted for FIVE YEARS.  
Thirteen- Month Limited Warranty:  
For the period of thirteen months from the date of purchase, in the event of defective materials  
or workmanship, Golden Technologies will repair or replace at our option any of the following  
structural frame components found to be defective by an authorized Golden Technologies  
representative:  
Caster Beam  
Anti-Tip Forks  
Caster Forks  
Armrests  
Footrest  
For the period of thirteen months from the date of purchase, in the event of defective materials  
or workmanship, Golden Technologies will repair or replace at our option any of the following  
drive train components found to be defective by an authorized Golden Technologies  
representative:  
Motor/Gearbox Assembly  
Brake Assembly  
(electrical function only)  
Note: An increase in operating noise of the motor/gearbox DOES NOT constitute a defect. With  
normal wear and tear, operating noise is expected to increase.  
For the period of thirteen months from the date of purchase, in the event of defective materials or  
workmanship, Golden Technologies will repair or replace at our option any of the following electronic  
assemblies found to be defective by an authorized Golden Technologies representative:  
Electronic Controller  
Battery Charger  
Wire Harness(es)  
(excludes boot covers)  
While charging batteries, it is normal for the battery charger to heat up. Heat coming  
from the battery charger DOES NOT constitute a defect.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
Consumer Limited Warranty  
Power Wheelchair (continued)  
For the period of thirteen months from the date of purchase, in the event of defective materials  
or workmanship, Golden Technologies will repair or replace at our option any of the following  
parts found to be defective by an authorized Golden Technologies representative:  
Bearings  
Bushings  
Seat swivel  
mechanism  
Rubber Components  
(excludes tires and all  
wear parts)  
Plastic  
Components  
(excludes body &  
all wear parts)  
Items not mentioned or listed are covered at the discretion of Golden Technologies. Any  
accessories, standard or optional, supplied by Golden Technologies, are covered for a period of  
one year from the date of purchase with the particular unit.  
Warranty Exclusions:  
Golden Technologies does not provide warranty on any of the following items which may require  
replacement due to the normal wear and tear of day to day usage:  
Tires and Tubes  
ABS Plastic Shrouds  
Armrest Pads  
Motor Brushes  
Bulbs/Fuses  
Battery Cases  
Brake Pads  
Upholstery  
This warranty also excludes the following:  
Batteries (Please consult battery manufacturer for any implied warranty)  
Loss or theft of components  
Damage caused by:  
Battery fluid spillage or leakage  
Abuse, misuse, accident or negligence.  
Improper operation, maintenance or storage.  
Commercial use or use other than normal.  
Repairs and/or modifications made to any part without the specific consent  
of Golden Technologies.  
Exceeding the specified weight capacity of the unit.  
Accessories other than those supplied or approved by Golden Technologies.  
Failure to adhere to the product instructions  
Acts of Nature, such as lightning strikes, earthquakes, etc….  
Circumstances beyond the control of Golden Technologies.  
ANY PARTS ALTERED OR REPAIRED BY UNAUTHORIZED PERSON.  
Warranty Service:  
Warranty Service must be performed by an authorized Golden Technologies representative.  
Golden Technologies reserves the right to replace warranted part(s) with refurbished or new  
part(s) at our discretion. All labor charges, service calls, transportation costs or any other  
charge(s) associated with the installation of any warranted part(s) are the responsibility of the  
consumer. Warranty is for the replacement of the parts only and does not include freight for  
the replacement parts. Consumers are not to return any item(s) to Golden Technologies without  
prior written authorization. Any damages incurred while warranted part(s) are in transport are  
the sole responsibility of the consumer.  
There is no other express warranty.  
Implied warranties, including those of merchantability and fitness for a particular purpose are  
excluded. Liabilities for consequential damages are excluded.  
This warranty gives you specific rights and you may also have other rights which may vary from  
state to state.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Compass Owner’s Manual – Models: GP600 SS, GP600 CC  
Revised 05/23/13  
Golden Technologies  
Product Registration Form  
Please fill out this product registration form or you can also register your product online  
should service be required.  
OWNER INFORMATION:  
Name: ____________________________________________________________  
Address: __________________________________________________________  
City: _____________________________________ State: ______ Zip: ____________  
PRODUCT INFORMATION:  
Serial Number: _____________________________________________________  
Purchased From: ____________________________________________________  
City: ______________________________________ State: ______ Zip: ____________  
Date Purchased: _______________  
MAIL COMPLETED FORM TO:  
Golden Technologies  
401 Bridge St.  
Old Forge, PA 18518  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fold Here First  
Place  
Stamp  
Here  
Golden Technologies  
401 Bridge St.  
Old Forge, PA 18518  
Fold Here Second  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
401 Bridge Street, Old Forge PA 18518  
Tel: (800) 624-6374 Fax: (800) 628-5165  
Y O U R L I F E I N M O T I O N  
CompassOwner’sManual.052313  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Dyson Vacuum Cleaner DC 14 User Manual
Electro Voice Microphone HM1x User Manual
Euro Pro Carpet Cleaner SC618HD User Manual
Everpure Water System EV9318 60 User Manual
Extron electronic Network Card PoleVault System A V Source Inputs User Manual
Fluke Furnace 9112A User Manual
Frigidaire Dehumidifier FAD504DUD User Manual
Galil Home Theater Server DMC 13X8 User Manual
Garland Oven PS 36RB 26 User Manual
Gianni Industries Door DG 25 User Manual