Global Machinery Company Portable Generator LS LINE REDEYE User Manual

INSTRUCTION MANUAL  
Deluxe Laser Line  
Generator  
Electronic alignment made easy  
• Melbourne • Perth • Auckland • Hong Kong • Shanghai  
LSLINE  
Taipei • New York • Verona • London • Paris  
040504 ed09 JJ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Description of symbols  
Dear Customer  
The rating plate on your tool may show symbols. These  
represent important information about the product or  
instructions on its use.  
If you require any help with your product, whether it  
is a Warranty claim, spare part or user information,  
please phone our Help Line for an immediate response.  
Phone 1300 880 001 in Australia or 0800 445 721 in  
New Zealand.  
Conforms to relevant standards for  
electromagnetic compatibility.  
Do not stare into beam. Only turn laser beam  
on when tool is on work piece. Class 2 laser  
product.  
Introduction  
Your new GMC laser hand tool will more than satisfy your  
expectations. It has been manufactured under stringent  
GMC Quality Standards to meet superior performance  
criteria.  
You will find your new tool easy and safe to operate,  
and, with proper care, it will give you many years of  
dependable service.  
Caution. Carefully read through this entire Instruction  
Manual before using your new GMC laser hand tool. Take  
special care to heed the Cautions and Warnings.  
Your GMC laser hand tool has many features that will  
make your job faster and easier. Safety, performance,  
and dependability have been given top priority in the  
development of this tool, making it easy to maintain  
and operate.  
Specifications  
Recommended Use:  
Indoor  
Length of laser line: Up to 10m  
Laser diode type:  
Laser class:  
Red laser diode 650nm  
Class 2, maximum power  
output less than or  
equal to 1mW  
Operation area:  
Up to 10m distance and/or up  
to 10m length of visible laser line  
(with help of red laser enhancing  
glasses, indoor)  
Laser fan beam angle: 100°  
Power supply:  
2 x AA – 1.5 volt batteries  
Environmental protection  
(not supplied)  
Recycle unwanted materials instead of  
disposing of them as waste. All tools, hoses  
and packaging should be sorted, taken to  
the local recycling centre and disposed of  
in an environmentally safe way.  
Battery life:  
40 hours of continuous use  
with alkaline batteries  
Operation temperature: -1°C to 40°C  
Dimensions:  
Weight:  
115mm x 54mm x 80mm  
Unit only (no batteries) 240g  
Base  
Batteries  
90g  
50g  
Accuracy:  
+/- 13mm at 10m  
CAUTION. Laser radiation is emitted from the  
line generator.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety rules for laser line generators  
Additional safety rules for laser  
line generator  
The laser line generator is Class 2 with maximum 1mW and  
400nm – 650nm wavelengths. These lasers do not normally  
present an optical hazard, although staring at the beam  
may cause flash blindness.  
The laser line generator emits a laser fan beam, which acts  
like an invisible surface in the actual three dimensions  
space. When used indoors, it generates a visible laser line  
on the surfaces the laser fan beam crosses.  
WARNING. Do not stare directly at the laser beam.  
The liner is a Class 2 laser tool and is manufactured to  
Australian standards, AS 2397 and AS/NZS2211.  
A hazard may exist if you deliberately stare into the beam,  
please observe all safety rules as follows;  
The two vials on the top of the laser line generator are  
for the laser fan beam alignment reference only. The unit  
is not a level and can not be used as a level. The laser  
line generator is not designed as a height measuring  
instrument and must not be used as such. It is designed  
to be referred to its projected line only.  
WARNING. Read and understand all instructions. Failure  
to follow all instructions may result in hazardous radiation  
exposure, electric shock, fire and/or bodily injury.  
Do not remove or deface any labels. Removing labels  
increases the risk of exposure to laser radiation.  
Do not stare directly at the laser beam as serious eye  
injury could result.  
The laser shall be used and maintained in accordance with  
the manufacturer’s instructions.  
Never aim the beam at any person or an object other than  
the work piece.  
The laser beam shall not be deliberately aimed at  
personnel and shall be prevented from being directed  
towards the eye of a person for longer than 0.25s.  
Always ensure the laser beam is aimed at a sturdy work  
piece without reflective surfaces. i.e. wood or rough  
coated surfaces are acceptable. Bright shiny reflective  
sheet steel or the like is not suitable for laser use as  
the reflective surface could direct the beam back at the  
operator.  
Do not project the laser beam directly into the eyes of  
others.  
Do not place the laser in a position which may cause  
anyone to stare into the laser beam intentionally or  
unintentionally.  
Do not change the laser light assembly with a  
different type. Repairs must be carried out by the laser  
manufacturer or an authorized agent.  
CAUTION. Use of controls, adjustments  
or performance of procedures other than  
those specified herein may result in  
hazardous radiation exposure.  
Do not use optical tools such as a telescope or transit  
to view the laser beam.  
LASER RADIATION  
IS EMITTED THROUGH  
THIS APERTURE  
Please refer to the relevant Australian  
Do not operate the laser line generator around children  
or allow children to operate the tool.  
Keep children and bystanders away while operating the  
laser line generator.  
standards, AS 2397 and AS/NZS2211  
LSLINE Deluxe Laser  
for more information on Lasers.  
Line Generator  
LASER LIGHT LASER RADIATION  
Do not stare into beam.  
Class 2 laser product.  
Turn the laser line generator off when it is not in use.  
Leaving the laser on increases the risk of staring into  
the laser beam.  
Made in China  
N380  
Do not operate the laser line generator in explosive  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
atmospheres, such as in the presence of flammable  
liquids, gases, or dust.  
a qualified repair facility. Repairs performed by  
unqualified personnel could result in serious injury.  
Do not push the pin push-button of the aluminium base  
unless you intend to fix the base on the dry wall or soft  
wood like material, it may result injury because of the  
sharp pins.  
To avoid injury, always make sure the push pins are  
fully retracted before handling or storing the laser line  
generator and keep the units and the base out of reach  
of children and other untrained persons.  
Do not disassemble the laser line generator.  
Disassembling the unit will void all warranties on the  
product.  
Do not disassemble any part of the product except  
removing the batteries cap when replacing batteries.  
Do not modify the product. Modifying the product  
in any way may result in hazardous laser radiation  
exposure.  
Position the laser line generator securely. Damage to  
the laser line generator or some injury could result if  
the unit falls.  
Use of control or performance of procedures other than  
those specified in this manual may result in hazardous  
laser radiation exposure.  
Use only accessories that recommended by the  
manufacturer for your model. Accessories that may be  
suitable for a specific laser line generator, may create a  
risk of injury when used on another laser line generator.  
Keep work area clean and well lit. Cluttered and dark  
areas invite accidents.  
Repairs and servicing can be only performed by  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Know your product  
Before using the laser line generator, familiarise yourself  
with all the operating features and safety requirements.  
Laser line generator  
1. Laser switch  
2. Laser line rotating dial  
3. Level vials  
4. Battery cover  
5. Magnetic base  
6. Front locating groove  
7. Rear locating groove  
Leveling base  
8. Vertical adjustment knob  
9. Horizontal adjustment knobs  
10. Locating pin  
11. Mounting thread  
15  
Pin mounting base  
12. Locating pin  
13. Pin push buttons  
14. Pin protective cover  
15. Laser enhancing glasses  
4
8
13  
14  
12  
9
1
11  
6 2  
3
5
7
10  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.If the floor is level, ensure the surface is made of  
soft material such as soft wood, then press both pin  
buttons (13) down into the flat surface and make sure  
it fixes firmly.  
Changing the laser line generator batteries  
1. Ensure that the laser line generator is switched OFF by  
checking that the laser lswitch (1) has been pulled up.  
2. Turn the battery cover (4) anticlockwise and remove  
the cap.  
Option 2: Flat surfaces – no mounting base  
1.Place the unit on the floor and check the vials (3) to  
ensure that the surface is level. If the floor is not level,  
go to option 3.  
3. Remove and replace both AA batteries, taking care  
to insert the new batteries with the correct polarity.  
4. Replace the battery cover (4) by turning it clockwise.  
CAUTION. Remove the laser line generator batteries when  
the tool is to be stored without use for a few days or  
more. If left in position, the batteries might leak and  
damage the laser light assembly.  
Damage due to leaking batteries is not covered under  
warranty.  
Operating the laser line generator  
The laser line generator has a number of different  
mounting methods. It is important to select the mounting  
method first as illustrated in the following options.  
Option 3: Uneven surfaces – leveling base  
1. Place the unit onto the leveling base ensuring you align  
the front locating groove (6) with the locating pin (10).  
Selecting the mounting method  
Option 1: Flat surfaces – pin mounting base  
1.Place the base of the unit onto the pin mounting base  
ensuring you align the front locating groove (6) with  
the locating pin (12).  
2.Place this assembly on a flat surface and check the vials  
2.Check vials (3) to see if  
the unit assembly is level.  
If not, make appropriate  
adjustments to both the  
vertical adjusting knob (8)  
and the horizontal adjusting  
knob (9).  
(3) to ensure that the surface is level. If the surface is  
not level, go to option 3.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Projection of inclined laser line  
on the opposite surfaces  
Switch ON the laser line  
generator and adjust the  
rotating dial (2) to the  
required inclined angle on the  
opposite surface.  
Projection of laser lines on the floor  
Once the mounting method has been selected you may  
commence with the projection of the laser line.  
The laser line rotating dial (2) is designed to adjust the  
line from horizontal to vertical and all angles in between.  
Switching it on  
To switch the laser line  
NOTE. Position the laser line  
generator ON, push down the  
laser switch (1) and the laser  
will then automatically appear.  
generator a maximum of 10m  
from the wall surface. It is  
recommended to use red laser  
enhancing glasses (15) to improve the visibility of the  
laser line especially in a bright light environment.  
Projection of laser line when fixed on a wall  
The laser line generator is built with a large laser fan  
angle (up to 100° of fan beam). When this is used in  
conjunction with the 90° rotating system dial (2), it  
offers wide range of line projections across main surfaces  
for different alignment applications.  
1. Attach the laser line generator to  
the pin mounting base.  
Projection of vertical  
laser line  
Switch ON the laser line  
generator and adjust the  
rotating dial (2) anticlockwise  
to achieve a vertical line.  
2. Position this mounting  
assembly onto the wall and  
check the vial (3) to ensure  
that the unit is in the  
general leveling position.  
Projection of horizontal  
laser line  
Switch ON the laser line  
generator and adjust the  
rotating dial (2) clockwise to  
achieve a horizontal line.  
3. Press both the pin buttons  
(13) onto the dry wall  
and check to ensure the  
assembly has been securely  
attached.  
4. Once the base has been  
secured you can still  
manouvre the laser line  
generator (if required)  
to achieve the correct  
horizontal level.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Switch ON the laser line  
generator.  
6. Adjust the rotating dial  
(2) to achieve desired line  
projection.  
Maintenance  
1. The laser line generator must be handled with care.  
2. Avoid shock, vibrations and extreme heat.  
3. Always store the tool indoor, switch to OFF position and  
put it in its protective case.  
4. Avoid dust and liquid into the tool, use damp cloth and  
mild soap to clean the tool.  
5. Keep the laser line generator dry and clean.  
6. Check the batteries regularly to avoid deterioration.  
7. No special maintenance operation is required to be  
carried except the change of batteries as per description  
given in this manual.  
Note: This tool is not to be tampered with and should  
only be repaired by a qualified Service Technician with  
laser experience.  
Troubleshooting  
Problem  
Possible cause  
Weak batteries  
Solution  
Faint laser line projection  
Replace batteries  
Bright lighted room  
Switch is not ON  
Use the laser enhancing glasses  
Laser line is not projected  
Check that the switch has been  
pushed down  
Batteries are flat  
Replace batteries  
Laser line angle appears not to line  
up with a reference point  
The rotating dial has not been  
positioned correctly  
Adjust the rotating dial to the  
correct position  
Mounting surface is not on a  
flat plane  
Check the vials. Use the leveling  
base and level the unit with the  
adjusting knobs  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Carefully read the entire Instruction Manual  
before using this product.  
With continuing product development changes may  
have occurred which render the product received  
slightly different to that shown in this instruction  
manual. The manufacturer reserves the right to  
Before returning this product for a  
Warranty Claim or any other reason  
Please Call 1300 880 001 (Australia)  
or 0800 445 721 (New Zealand)  
change specifications without notice. Note:  
Specifications may differ from country to country.  
When you make your call, please have  
the following information at hand:  
GMC Product Type GMC Product Code  
A GMC Service Engineer will take your call and, in  
most cases, will be able to solve your problem over  
the phone.  
The GMC 777 Helpline operates from 7am to  
7pm, 7 days a week (EST). This allows you  
to contact GMC directly with any queries and  
technical questions you have regarding  
our products.  
You are welcome to use this phone-in service to  
make suggestions or give comments about any  
GMC product.  
45–55 South Centre Road  
Melbourne Airport  
Victoria, Australia 3045  
Tel: (03) 8346 1100 Fax: (03) 8346 1200  
Save this Manual for future reference.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Eclipse Fujitsu Ten MP3 Player CD1200 User Manual
Fisher Paykel Cooktop 599127 User Manual
Fortinet Network Card FSAE User Manual
Frigidaire Air Conditioner THRU THE WALL ELECTRONIC CONTROL AIR CONDITIONER User Manual
FujiFilm Digital Camera Zoom Date 110ez User Manual
Fujitsu Server TX150 S4 User Manual
Fusion Marine Instruments MS RA50 User Manual
Fusion Speaker CP SW100 User Manual
Generac Portable Generator 004692 2 User Manual
Gitzo Camcorder Accessories G1504 User Manual