2400W
SILENT SHREDDER
SHS2400
INSTRUCTION MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING. Keep spectators away. Beware of
objects being flung out.
Introduction
Your new GMC power tool will more than satisfy
your expectations. It has been manufactured under
stringent GMC Quality Standards to meet superior
performance criteria.
WARNING. Do not put hands or feet under the
cover of the machine when it is running.
WARNING. Rotating blades.
You will find your new tool easy and safe to operate,
and, with proper care, it will give you many years
of dependable service.
The blades will continue to rotate after the machine
has been switched off.
CAUTION. Carefully read through this entire Instruction
Manual before using your new GMC Power Tool. Take
special care to heed the Cautions and Warnings.
WARNING. Remove the plug from the wall socket
before carrying out any kind of maintenance.
Do not leave this electrical tool in the rain.
Your GMC power tool has many features that will make
your job faster and easier. Safety, performance, and
dependability have been given top priority in the
development of this tool, making it easy to maintain
and operate.
WARNING. Rotating blades keep hands away
from discharge.
Specifications
Environmental protection
Voltage:
230–240 Vac ~ 50Hz
2400W
46 min-1
Recycle unwanted materials instead
of disposing of them as waste. All tools,
hoses and packaging should be sorted,
taken to the local recycling centre and
disposed of in an environmentally safe way.
Input power:
Speed:
Maximum shredding diameter: 40mm
Blade cylinder size:
Blade length:
Insulation:
88mm
Description of symbols
The rating plate on your tool may show symbols. These
represent important information about the product or
instructions on its use.
70mm
Earthed appliance
24.5Kg
Weight:
Wear hearing protection.
Wear eye protection.
Protection:
IPX4
Wear breathing protection.
Conforms to relevant standards for electromagnetic
compatibility.
Read these instructions for use carefully.
Wear protective gloves.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Personal safety
General safety rules
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
WARNING. Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury. The term “power tool” in all of the
warnings listed below refers to your mains operated (corded)
power tool or battery operated (cordless) power tool.
Save these instructions
1. Work area
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
c. Avoid accidental starting. Ensure the switch is in the
off position before plugging in. Carrying power tools with
your finger on the switch or plugging in power tools that
have the switch on invites accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
c. Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
• During use, the machine should be level and on a
firm surface.
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
• Ensure that all screws and nuts are properly tightened
before use.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work to be performed. Use of the power tool for
operations different from those intended could result in a
hazardous situation.
• Only use the machine in dry conditions and never
outdoors when it is raining.
• Never use the machine with damaged safety devices
or without protection.
• Keep hands, other parts of your body and clothing away
from the feeding hopper and the discharge chute.
• Keep your face and the rest of your body away from the
feeding hopper.
• Do not leave the machine unsupervised, switch off the
motor and disconnect the plug.
• Hard objects such as stones, bottle, cans or pieces of
metal must not be fed into the inlet chute. This can cause
damage to the machine.
• If the machine becomes blocked, stop the motor and
disconnect the plug. Pull out any objects and check
for damage.
• If the fuse blows or if the overload protection is triggered,
this is a sign that the machine is overloaded and/or
that too many appliances are connected to the same
extension cable. Check the cause and remedy. Do not
install a more powerful fuse.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
• Do not tug on the extension cable. Do not hold the cable
taut. This can cause damage in the plugs or in
the cables insulation. Such damage is invisible but can
be dangerous.
Additional safety rules for shredders
• This appliance is not intended for use by young children
or infirm persons unless they have been adequately
supervised by a responsible person to ensure that they
can use the appliance safely.
• Always keep the extension cable away from the machine.
Disconnect the plug from the electric socket and check
the cable regularly for signs of damage or ageing. Do not
use the machine with a damaged extension cable.
• Young children should be supervised to ensure that they
do not play with the appliance.
• If the cable is damaged, it must be replaced by an
authorised service centre in order to avoid a hazard.
• Wear protective gloves, protective glasses and hearing
protectors. Avoid loose clothing.
• Never move the machine by pulling the cable. The
machine must not be moved with the motor running.
• Always stand steadily and in balance. Do not stretch
towards the machine.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
The GMC Shredder is supplied with the following
accessories as standard:
• Allen key
Unpacking
Due to modern mass production techniques, it is unlikely
that your power tool is faulty or that a part is missing.
If you find anything wrong, do not operate the tool
until the parts have been replaced or the fault has
been rectified. Failure to do so could result in serious
personal injury.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Know your product
1. Shredder body
2. On/off switch
3. Forward/Reverse Switch
4. Overload protection button
5. Handle
1
18
6. Inlet chute
7. Discharge chute
8. Leg (x 2)
3
9. Wheel (x 2)
10. Wheel cover (x 2)
2
11. Axle
4
12. Axle tube
13. Wheel bush (x 2)
14. Hex bolt (x 2)
15. Washer (x 4)
7
16. Nut (x 2)
17. Allen key
18. Blade adjusting screw
19. Wave washer (x 2)
20. Spring washer (x 2)
8
13
12 11
17
20 19
16
9
10
15
14
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Position the remaining
washers and the locking
nuts (16) on each end of
the axle and tighten both
the wheel nuts using a
suitable spanner.
Assembly
Attaching the legs and wheels
WARNING. You may need assistance when lifting the
machine out of the box and assembling.
Note. The legs should be splayed out at the bottom to give
stability to the unit.
5. Push the wheel covers (10)
firmly onto the wheels.
��
�
WARNING. Take care when
tilting the unit onto its wheels
as the unit has an uneven
weight distribution when
tilted and during wheeled
transportation.
��
��
��
��
��
1. Position the axle tube (12) between the two wheel
supports (8).
Fitting the legs
to the shredder
2. Slide the axle (11) through the hole in one of the wheel
supports (8) then through the axle tube (12) and out
through the hole in the other wheel support.
1. Turn the shredder over onto
its side to reveal the wheel
support fixing holes on the
underside of the shredder
body (1).
2. Push the legs (8) into
position.
3. Align the holes in the
legs with the fixing holes in
the shredder body (1).
4. Secure the legs using
the hex bolts (14) and
wave washers (21) using
the small allen key (17)
supplied.
3. Position the washers (15),
and wheel bushes (13) on
each end of the axle.
Push the wheels (9) onto
each end of the axle (11).
WARNING. To ensure the
stability of the shredder, make
sure that the cap headed
bolts and wave washers are
securely tightened.
Note. The wheels must be
fitted the correct way round
to allow the nuts to tighten on
each end of the axle.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing direction of rotation
WARNING. The rotation direction switch can only be used if
the shredder is switched off.
Operation of the shredder
Starting the motor
WARNING. Ensure that the shredder is empty before
starting the motor.
Position
For forward action turn the
forward/reverse switch to the
right. The cutting blades pull
the material in and
1. Connect the shredder power cord to an appropriate
extension cord and plug it in to the mains power.
2. To start the motor, first make sure the yellow switch is in
the forward position and then press the green section of
the on/off switch (2) marked with an .
shred it.
Position
The cutting blades run in the
opposite direction and release
the clogged material.
Press the green on switch
(2) after you have moved the
forward/reverse switch to the
left
.
The cutting blades run now
in the opposite direction.
If you release the on/off
switch the shredder will stop
automatically.
Stopping the motor
Stop the motor by pressing the
red section of the
on/off switch (2) marked O.
Overload protection
WARNING. Do not feed in any
material after the motor has
been stopped. This will get
caught in the machine and can
make restarting impossible.
The shredder is equipped with a built-in motor protection
which prevents the motor being overloaded.
In the event of overloading, the current is broken and the
main switch is turned off
automatically .
Disconnect shredder from
power supply and move the
direction of rotation switch to
O position before attempting
to unblock any jams.
Allow at least 5 minutes for
the motor to cool down.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Push in the overload protection button (3) to re-set, mains
power can now be switched on.
To prevent damage to the machine, you are recommended
not to exceed the following maximum sizes of twigs and
branches:
• 40mm in diameter.
The material that is to be mulched is fed into the inlet chute
(1) and, assuming it is not too bulky, automatically pulled
down through the slowly rotating spiral cutter to the blades.
Branches and twigs should be mulched shortly after being
cut. They become extremely hard when they dry out, and
the maximum diameter of what can be mulched is reduced.
Heavy material or twigs will jam the blades if you let the
machine cut continually. A large proportion of garden waste
contains a lot of water and therefore sticks easily. Such
material should be allowed to dry for a few days before
being processed.
If the cutting blades are jammed turn the rotation direction
switch to position , before switching the shredder back
on again, to clear any clogged material.
Disconnect switch
Check all the material you want to shred carefully. Make
sure it doesn’t contain any stones or nails as this might
severely damage the shredder.
The machine is equipped with a disconnect switch. This
means that the main switch is automatically disconnected
in the event of a loss of current. The machine can be
started again by reconnecting the plug and turning on
the main switch.
Be aware of vibrations. Heavy vibrations are caused by
damaged or worn out blades. Store the shredder indoors in
a dry place.
Mulching
Mulching palm fronds
The following types of material can be mulched in the
shredder:
The GMC shredder is designed to effectively handle palm
fronds, reducing them to an easily disposable waste.
• Twigs and branches.
If the head of the palm frond is particularly large or
hard it may have to be removed before it is inserted into
the shredder.
• Waste from cutting bushes.
• Waste from hedge-trimming.
If the material is particularly fibrous or hard then you may
have to loosen the blade adjustment screw (10) as outlined
in section ‘Adjusting the cutting gear’ and run the material
through once to soften it. Then retighten the adjustment
screw and insert the material a second time to effectively
shred it.
Examples of materials which are not suitable for
mulching include:
• Glass, metal, plastic bags, stones, fabric,
earth covered roots.
• Waste that does not have a firm consistency,
e.g. kitchen waste.
Composting
• Soft Leafy material.
The processed material can be composted in various ways:
• The material can be placed in a heap directly on the
ground (cold composting).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
• The material can be placed in a plastic container,
wooden crate, skeleton container or similar (cold
composting).
2. If you are shredding heavy materials (such as harder
or large materials) they may need to be put through the
shredder twice, to crush the material before cutting it
completely. To loosen the adjusting screw, turn the allen
key anti-clockwise half a turn, in the CRUSH direction.
• The material can be placed in an insulated compost
holder. The heat is then held for longer and the rotting
process also continues during the winter. This method
produces faster results (warm composting).
After you have completed the adjustment, check if the blade
cuts efficiently. To avoid and damage to the shredder make
sure that the cutting blade does not come into contact with
the anvil blade.
• The material can be spread directly onto the garden
(surface composting).
Maintenance and storage information
Adjusting the cutting gear
WARNING. Prior to cleaning or any maintenance, always
ensure the power plug has been removed from the
electrical power supply.
0 - 0.5mm
B
Always wear protective gloves to avoid injury.
Generally speaking, shredders require very little
maintenance. In order to maintain the efficiency of the
machine and to achieve a long service life, observe
the following:
10
A
• Keep the air openings clean and free of
obstructing material.
The anvil blade B should be adjusted the have a distance of 0.5
to 1mm from the cutting bladeA. This distance should be kept to
guarantee effective operation of
• Check the customer-installed nuts and
screws (tighten if necessary).
• Spray the spiral cutter after each use with an
environmentally-friendly, biodegradable spray oil to
protect against corrosion.
the machine.
Soft materials or wet twigs can get torn instead of cut properly
due to wrong adjustment. Also a blunt anvil blade from frequent
use produces the same problem.
Cleaning
Always clean the shredder after each use.
On the right hand side of the
WARNING. Never use a high-pressure washer or running
water when cleaning the shredder!
shredder you will find the blade
adjustment screw (10). To adjust
the distance turn the screw to the
right, with the supplied allen key.
Brush away dirt and plant residue which may be caught in the
spiral cutter. Wipe clean the outside of the shredder with a cloth
which has been moistened with a mild detergent and water.
1. For lighter material,
|you can cut through the
material completely
turn the allen key clockwise
half a turn, in the CUT
direction.
Power cord maintenance
If the supply cord needs replacing, the task must be carried
out by the manufacturer, the manufacturer’s agent, or an
authorised service centre in order to avoid a safety hazard.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
GMC customer assist
If your product needs repairing, replacing,
technical service or you simply need help or advice,
please contact us on our Customer Assist Line
1300 880 001 (Australia) or 0800 445 721 (New Zealand).
For prompt service we suggest you log your service request
access to the Internet, please contact our service department
on 1300 880 001 (Australia) or 0800 445 721 (New Zealand).
7am –7pm, 7days a week (AEST).
Please note that if repair or replacement is required,
you must provide a valid original purchase receipt.
You will need the following details at hand to log your service request;
Personal details: First & Last name, address, pick up address,
contact phone numbers, email address
Product details: Product number, date of purchase, retailer bought from,
State & postcode, receipt number, reason for the request,
copy of official purchase receipt
Attach your purchase receipt and save with this Manual for future reference.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
|