INSTRUCTION MANUAL
1/5 HP / 2/5 HP / 2/3 HP / 1/2 HP
Bench Grinders
BG125A
BG150A
BG200A
NTS2000A
• Melbourne • Perth • Auckland • Hong Kong • Shanghai
031222 ED8 DR
• Taipei • New York • Verona • London • Paris
Download from Www.Somanuals.com. All Manuals Search And Download.
Dear Customer
Description of symbols
If you require any help with your product, whether it is a
Warranty claim, spare part or user information:
The rating plate on your tool may show symbols. These
represent important information about the product or
instructions on its use.
Please phone our Help Line for an immediate response.
Phone 1300 880 001 in Australia or 0800 445 721 in
New Zealand.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Conforms to relevant standards for
electromagnetic compatibility.
Introduction
Your new GMC power tool will more than satisfy your
expectations. It has been manufactured under stringent
GMC Quality Standards to meet superior
performance criteria.
Specifications
Nominal voltage: 230 – 240Vac ~ 50Hz
You will find your new tool easy and safe to operate, and,
with proper care, it will give you many years of
dependable service.
Caution. Carefully read through this entire Instruction
Manual before using your new GMC Power Tool. Take
special care to heed the Cautions and Warnings.
Your GMC power tool has many features that will make
your job faster and easier. Safety, performance and
dependability have been given top priority to the
development of this tool, making it easy to maintain
and operate.
Model/Wheel
BG125A/1
BG125A/2
BG150A/1
BG150A/2
BG200A/1
BG200A/2
NTS2000A/1
NTS2000A/2
HP
Spindle speed
2800RPM
2800RPM
2800RPM
2800RPM
2800RPM
2800RPM
2800RPM
130RPM
Grit
36
60
36
60
36
60
36
100
1/5 HP
1/5 HP
2/5 HP
2/5 HP
2/3 HP
2/3 HP
1/2 HP
1/2 HP
Model/Wheel
BG125A/1
BG125A/2
BG150A/1
BG150A/2
BG200A/1
BG200A/2
NTS2000A/1
NTS2000A/2
Diameter
125mm
125mm
150mm
150mm
200mm
200mm
150mm
200mm
Width
16mm
16mm
20mm
20mm
20mm
20mm
20mm
40mm
Bore
Environmental protection
Recycle unwanted materials instead of
disposing of them as waste. All batteries,
tools, hoses and packaging must be sorted,
taken to the local recycling centre and
recycled or disposed of in an environmentally
safe way.
12.7mm
12.7mm
16mm
16mm
16mm
16mm
16mm
20mm
3
Download from Www.Somanuals.com. All Manuals Search And Download.
• Damage to hearing if effective earmuffs are not worn.
• Damage to eyes if eye protection is not worn
Safety instructions
The tool must be used only for the prescribed purpose.
Any uses other than those mentioned in this manual will
be considered a case of misuse. The user and not the
manufacturer shall be liable for any damage or injury
resulting from such cases of misuse.
• Damage to lungs if breathing protection is not worn
• Always remove the plug from the mains socket before
making any adjustments or maintenance, including
changing the wheel.
To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operating
instructions to be found in this Manual. All persons who
use and service the machine have to be acquainted with
this Manual and must be informed about its potential
hazards. Children and infirm people must not use this
tool. Children should be supervised at all times if they are
in the area in which the tool is being used. It is also
imperative that you observe the accident prevention
regulations in force in your area. The same applies for
general rules of occupational health and safety.
The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
Warning. Before connecting a tool to a power source
(mains power point receptacle, outlet, etc.), be sure that
the voltage supply is the same as that specified on the
nameplate on the tool. A power source with a voltage
greater than that specified for the tool can result in
serious injury to the user, as well as damage to the tool.
Warning. When using power tools, basic safety
precautions should always be taken to reduce the risk of
fire, electric shock and personal injury. Also, please read
and heed the advice given in the additional important
safety instructions.
1. Keep the work area clean and tidy. Cluttered work
areas and benches invite accidents and injury.
2. Consider the environment in which you are working.
Do not use power tools in damp or wet locations. Keep
the work area well lit. Do not expose power tools to
rain and high humidity. Do not use power tools in the
presence of flammable liquids or gases.
3. Keep visitors away from the work area. All visitors
and onlookers, especially children and infirm persons
should be kept well away from where you are working.
Do not let others in the vicinity make contact with the
tool or extension cord.
4. Store tools safely. When not in use, tools should be
stored in a dry, high place or locked up out of reach.
5. Do not force the tool. The tool will do the job
better and safer working at the rate for which it
was designed.
If in doubt, do not plug in the tool. Using a power source
with a voltage less than the nameplate rating is harmful
to the motor.
6. Use the correct tool for the job. Do not force small
tools or attachments to do the job best handled by a
heavier duty tool. Never use a tool for a purpose other
than that for which it was intended.
Even when the tool is used as prescribed it is not possible
to eliminate all residual risk factors. The following hazards
may arise in connection with the tool’s construction
and design:
7. Dress correctly. Do not wear loose clothing or jewelry.
They can be caught in moving parts. Rubber gloves and
non-slip footwear are recommended when working
outdoors. If you have long hair, wear a protective
hair covering.
• Contact with the wheel.
• Kickback of work piece and parts of work piece.
• Wheel fracture.
• Catapulting of wheel pieces.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Use safety accessories. Safety glasses and earmuffs
should always be worn. A face or dust mask is
also required.
18. Stay alert. Watch what you are doing. Use common
sense. Do not operate a power tool when you
are tired.
9. Connect dust extraction equipment. If devices are
provided for the connection of dust extraction and
collection facilities, ensure that these are connected
and properly used.
10. Do not abuse the power cord. Never pull the cord to
disconnect the tool from the power point. Keep the
cord away from heat, oil and sharp edges.
11. Secure the work piece. Use clamps or a vice to hold
the work piece. It is safer than using your hand and
frees both hands to operate the tool.
19. Check for damaged parts. Before using a tool, check
that there are no damaged parts. If a part is slightly
damaged, carefully determine if it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, proper mounting and any other
conditions that may affect the operation of the tool.
A part that is damaged should be properly repaired or
replaced by an authorised service facility, unless
otherwise indicated in this Instruction Manual.
Defective switches must be replaced by an authorized
service facility. Do not use a tool if the switch does
not turn the tool on and off correctly.
12. Do not overreach. Keep your footing secure and
balanced at all times.
13. Look after your tools. Keep tools clean and sharp for
better and safer performance. Follow the instructions
regarding lubrication and accessory changes. Inspect
tool cords periodically and, if damaged, have them
repaired by an authorised service facility. Inspect
extension cords periodically and replace them if
damaged. Keep tool handles dry, clean and free from
oil and grease.
14. Disconnect idle tools. Switch off the power and
disconnect the plug from the power point before
servicing, when changing accessories and when the
tool is not in use.
20. Guard against electric shock. Prevent body contact
with grounded objects such as water pipes, radiators,
ranges and refrigerator enclosures.
21. Use only approved parts. When servicing, use only
identical replacement parts. Use an authorised service
facility to fit replacement parts.
Warning. The use of an accessory or attachment,
other than those recommended in this Instruction
Manual, may present a risk of personal injury.
15. Remove adjusting keys and wrenches. Form the
habit of checking to see that keys and adjusting
wrenches are removed from the tool before switching
it on.
16. Avoid unintentional starting. Always check that the
switch is in the OFF position before plugging in the
tool to the power supply. Do not carry a plugged in
tool with your finger on the switch.
17. Use outdoor rated extension cords. When a tool is
used outdoors, use only extension cords that are
intended for outdoor use and are so marked.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
• When using the grinder, use safety equipment including
safety goggles or shield, ear protection, dust mask and
protective clothing including safety gloves.
Additional safety rules for bench grinders
• Always remove the plug from the mains socket before
making any adjustments or maintenance, including
changing the wheel.
Wear goggles
• Always wear eye protection and check that the eye
shields on the grinder are properly adjusted.
• Always turn the grinder off when it is not in use and
never leave it unattended without first switching off
and removing the power plug. Never leave the grinder
until the grinding wheels have come to a complete stop.
• Make sure that any replacement wheel is rated at
3000RPM or higher.
• Do not let anyone under 18 years operate this tool.
Wear ear protection
Wear a breathing mask
Unpacking
Due to modern mass production techniques, it is unlikely
that your GMC Power Tool is faulty or that a part is
missing. If you find anything wrong, do not operate the
tool until the parts have been replaced or the fault has
been rectified. Failure to do so could result in serious
personal injury.
• Rags, cloths, cord, string and the like should never be
left around the work area.
Connecting to the power supply
The GMC Bench Grinders covered in this manual are
designed to operate from a standard household supply of
230-240V AC. Prior to plugging in the tool, check the
rating label on the rear of the grinder and ensure that it
states the tool’s operating voltage is 240V.
All the grinders are of Class 1 Category (earthed) and are
fitted with a 3-core cable and plug. Should the cable or
plug be damaged, the product should be serviced by an
authourised Service Centre to avoid a hazard.
• If you are interrupted when operating the tool,
complete the process and switch off before looking up.
• Periodically check that all nuts, bolts and other fixings
are properly tightened.
• Do not use a wheel that has received a blow, especially
to the side of the wheel.
• Replace a cracked or suspect wheel.
• Always allow a new wheel to run for a few minutes at
full speed before using it. Stand to one side at start up.
• Check that the wheel rotates freely each time before
start up.
• Do not use the grinder unless all the guards are properly
fitted and secure.
• Check that the tool rests are properly adjusted before
commencing use.
• Do not overload the grinder. Allow the grinder to run at
full speed, or close to full speed during use.
• Never apply excessive pressure to the wheel. It might
shatter causing personal injury.
• Make sure that the wheel is not in contact with the
work when you start the grinder.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Eye shield
2. Grinding wheel
3. Outer guard
4. Rubber coated
mounting position
5. Base
7. Adjustable tool rest
8. Wheel guard
9. Eye shield bracket
10. Water bath
11. Sharpening wheel
12. Guard exhaust
(not shown)
Know your product
Before using the bench grinder, familiarise yourself with
all the operating features and safety requirements.
The GMC Bench Grinders are designed for light to
moderate duty applications in a home environment. They
are not intended for use by trade persons. They are ideal
for sharpening tools such as drill bits and chisels. The
larger tools can be applied to heavier grinding
applications on steel sections. These grinders are not a
continuously rated tool and should not be operated for
more than 10 minutes continuously at a time under load.
If the tool is used for this period of time under load the
grinder should then be turned off for a minimum of
30 minutes.
6. On/Off switch
9
1
All the bench grinders can be fitted with a wire wheel
provided that the wheel is rated for use at 3000RPM
or higher.
Guard exhaust
3
2
7
All grinders are fitted with a rear guard
exhaust. This exhaust is provided to assist
in the prevention of grinding dust build up
within the guard assembly. Grinding sparks
and dust will project from these exhausts
from the rear. Ensure the following:
8
6
4
5
• Combustable items are not
directly behind the grinder.
• During use ensure other
persons are not directly
behind the grinder.
• Never attempt to connect
any form of dust extraction
machine to the grinder.
11
9
1
2
7
10
8
6
4
5
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution. During use it is important not to overload the
grinder. The grinder should run at close to full speed. If
you are applying too much pressure the grinder will start
to slow down. Under these conditions, remove the part
being ground and allow the grinder to return to full
speed. Re-apply the part to the grinder, but with a little
less force.
All of the grinding wheels are supplied with grinding
wheels designed for metal use only. The grinding of
Copper, Brass, Aluminium, Wood or other similar materials
will “clog” the grinding wheel.
through both the bracket
(9) and eye shield (1).
Tighten the screw to the
point where the eye shield
will move with firm
resistance.
5. Slide the eye bracket
inward or outwards so the
edge of the bracket is less
than 6mm from the surface
of the wheel as shown, but not touching the wheel.
Warning. Never attempt to grind Magnesium.
6. Rotate the wheel by hand one full revolution to ensure
the wheel can rotate without contacting the bracket.
Firmly tighten the screw retaining the bracket.
Important. Ensure that the washers as shown in the
photograph are correctly positioned.
Fitting and adjusting the eye shields
and brackets.
Important. Prior to fitting the eye shield brackets, ensure
the grinder is turned off and the power plug is removed
from the socket.
Fitting the tool rests.
The tool rests (7) are required for each high speed
grinding wheel to assist in the grinding operation. (They
are not required on the sharpening wheel on the
NTS2000A).
Caution. Never use a Bench Grinder on which the tool rest
has not been fitted or where the tool rest has not been
correctly adjusted.
Note. Always check to ensure the eye shields (1) are
correctly fitted and the eye shield brackets (9) are
correctly adjusted each time the grinder is used. Eye
shields and brackets must be fitted over each grinding
wheel on all the bench grinders in the range, except the
sharpening wheel (11) on Model NTS2000A.
1. Remove the top screw of
the wheel guard (8).
The tool rests supplied are left or right handed.
2. Fit the eye shield bracket (9).
Important. Prior to fitting the tool rests, ensure the
grinder is turned off and the power plug is removed from
the socket.
1. Remove the lower screw on
the wheel guard (8).
2. Hold the tool rest (7) in
the correct position against
the outer surface of the
inner wheel guard. Fit the
screw through the tool rest
and then both sides of the
guard ensuring the square
3. Fit a flat steel washer on to
the wheel guard screw and
then pass the screw through
the eye shield bracket,
guard and then the eye
shield bracket again. Fit
another flat washer,
followed by the spring washer and then the nut.
Tighten the nut so the bracket can slide.
4. Fit the eye shield (1) to the top of the bracket. Secure
the eye shield by passing the 45mm x 5mm screw
8
Download from Www.Somanuals.com. All Manuals Search And Download.
section under the screw
head fits into the slot of
the tool rest. Fit the star
washer and then the large
flat washer.
3. Fit the plastic coated
thumb nut to the screw
and tighten the nut
Note. The four rubber suction caps should remain in place
if mounting screws are used.
Using the On/
Off switch
1. To turn the grinder on,
press the top of the rocker
switch (6) marked “I”
sufficiently to support the
tool rest but still allowing
the tool rest to slide inward and outwards.
4. Slide the tool rest to within a max of 1.5mm from the
wheel. Rotate the wheel one full revolution by hand to
ensure the wheel does not contact the tool rest.
2. To turn the grinder
off, press the bottom of
the rocker switch (6)
marked “O”.
Operation
Important. Prior to using the grinder, check that the eye
shields and tool rests are fitted and correctly adjusted and
that you are wearing safety gear including eye, hearing
and breathing protection.
1. Turn the wheel by hand to make sure it does not touch
the guard and runs freely.
5. Tighten the thumb nut firmly to retain the assembly.
Repeat the assembly operation for the second
grinding wheel.
Important. Ensure that the washers as shown in the
photograph are correctly positioned.
2. Stand to one side, turn the switch (6) on and allow the
motor to reach full speed.
3. Support the work piece on the tool rest (7) and
gradually feed the work piece onto the wheel. Use pliers
to hold small work pieces.
Bench mounting the grinder
The GMC Bench Grinders are supplied with 4 rubber suction
caps which assist in reducing the transmission of vibration.
It is strongly recommended that the grinder be firmly
mounted to a bench or stand for safe operation.
The base of the grinder has a 7mm hole in each corner.
These holes accept screws or bolts up to 6mm diameter.
Mounting screws are not supplied with the unit.
Where the grinder is to be mounted on to a steel work
bench, it is advisable to place a piece of timber between
the bench and grinder then screw or bolt through the
grinder and timber into the bench. This further assists to
reduce vibration.
Important. When directly mounting the grinder ensure:
• The surface under the grinder is flat and clean.
• The 4 mount screws are applied evenly and not
over tightened.
Note. Traverse the work piece across the full width of the
wheel to prolong its flat surface.
4. If the grinding operation causes the motor speed to
noticeably decrease, pull back the work piece, allow
the motor to regain full speed and restart the
grinding operation, but apply less force.
Warnings. Only use the front face of the grinding wheel,
not the sides. Note that the work piece can get very warm.
It may be necessary to cool a work piece by dipping it in a
coolant or in water. Do not apply coolant or water to the
grinding wheel.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Replace the retaining nut.
(See the Note above
regarding the direction of
rotation of the nut).
7. Hold the wheel whilst you
tighten the nut. Do not
over tighten.
Changing a grinding wheel
(high speed wheel)
Important. Prior to changing
a wheel, ensure the grinder is
turned off and the power plug
is removed from the socket.
Make sure that the
replacement wheel is rated at
3000RPM or higher.
8. Replace the guard and eye
shield assembly.
1. Remove the retaining screw
and take off the tool rest (7).
9. Re-adjust the tool rest and
eye shield.
2. Remove the retaining screw
and take off the eye shield
bracket (9) and eye
shield (1).
10. Rotate the wheel by hand
to check for free
movement and proper
adjustments.
3. Take off the third retaining
screw and remove the outer
guard (3).
4. Remove the retaining nut
(see note below for correct
direction of rotation), outer
flange and the wheel.
Note. The wheel on the left-
hand side of the grinder has a
left-hand thread and is
11. Plug in the grinder, put
on eye protection, stand
to one side and run the
grinder at full speed for several minutes.
Changing the sharpening wheel (low speed
wheel for Model NTS2000A)
The NTS2000A is a combination Bench Grinder / Sharpener,
fitted with a wet bath on the sharpening wheel.
The sharpening wheel rotates at a much slower rate at
130RPM, and together with the water bath assists to keep
the part being sharpened cool and thus not damaging the
cutting edge.
The water also assists in keeping the wheel clean.
Water should be drained at the completion of the
unscrewed in a clockwise
direction. The wheel on the
right-hand side of the grinder
has a right-hand thread and is
unscrewed in an
anti-clockwise direction.
sharpening task via the small drain hole on the bottom of
the water bath. Ensure the rubber plug is firmly replaced.
5. Fit the replacement wheel
on the shaft ensuring that
there is a blotter between
the wheel and clamp
washers on each side of the
wheel, and ensure the
When filling the bath with water ensure the water is clean
and fill the bath sufficiently to allow the wheel to be
approx 12mm into the water. As you add the water to the
bath, the sides of the wheel will become wet, thus
indicating the depth of the wheel in the water. Do not
overfill the bath.
wheel is a slide fit (not
loose) on the spindle.
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
1. Drain all the water from the bath (10).
2. Remove the two securing screws at the top of the bath.
10. Fit the outer flange against
the outer blotter of the
wheel, followed by the steel
washer and then the
retaining nut.
11. Tighten the retaining nut
firmly by rotating the
spanner in a clockwise
direction.
12. Replace the water bath in the reverse direction as the
removal procedure given above.
How to true and dress the wheels
3. Loosen, but do not remove
the lower retaining screw.
4. Push the top clips of the
bath clear of housing and
then lower the bath clear of
the housing.
Dressing a wheel cleans and levels the front surface to
increase efficiency of operation and prevent vibration.
1. Dressing a wheel involves the use of a wheel dresser
which is not supplied with the grinder. Follow the
manufacturers instructions of the wheel dresser.
2. Adjust the tool rest to allow the front part of the wheel
dresser to fit between the tool rest and wheel.
3. Start the motor and move the dresser across the front
of the wheel a sufficient number of times until the
surface is level. It is not necessary to apply excessive
force in an attempt to dress the wheel in one pass of
the wheel dresser.
5. Using an 18mm spanner,
remove the wheel retaining
nut by turning the nut in an
anti-clockwise direction.
6. Remove the washer and the
outer flange, followed by
the wheel.
4. Adjust the tool rest so that it is no more than 1-1.5mm
from the wheel.
5. Adjust the eye shield bracket to ensure the gap between
the bracket and wheels is less than 6mm.
7. Ensure the new wheel
conforms to the replacement
wheel specifications in this
manual.
8. Ensure the clamping surfaces
are clean and fitted with
blotters.
9. Fit the wheel on to the
spindle and directly against
the inner flange.
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
Grinder adjustments
During the life of the grinder some adjustments are
required to maintain a safe working environment. Please
ensure the following:
Cleaning
1. Keep the outside of the grinder clean by brushing grinding
dust and dirt away from all areas where the dust tends to
build up.
• Always adjust the eye shields to the most
comfortable and most effective angle to suit the task
being performed.
• As the wheels wear, the top eye shield bracket must be
adjusted to ensure the gap between the bracket and the
wheel does not exceed 6mm.
2. Wipe the guards and grinder with a soft damp cloth. A
mild detergent can also be used.
3. Wipe the eye shields with a soft damp cloth, making
sure not to scratch the surface. A mild detergent can also
be used.
Caution. Never use caustic agents, petrol based cleaners,
• As the wheels wear the tool rests must also be adjusted alcohol or any other cleaning agents. Do not wet down
so there in never a gap of greater than 1.5mm between the grinder.
the wheel and the edge of the tool rest.
General inspection
Maintenance
Prior to any maintenance ensure the power has been
turned off and the plug is removed so that the grinder is
fully disconnected from the 240V supply.
1. Regularly check that all the fixing screws are tight. They
may vibrate loose over time.
Repairs
1. Only an authorised service centre should replace the
cordset or carry out other repairs. If the cordset is
damaged or worn, have it repaired or replaced by an
authorised service centre.
Lubrication
1. All models use pre-lubricated sealed ball bearings for
the motor and do not require lubrication.
2. If the wheels do not rotate freely, the bearings should
be replaced by an authorised service centre.
3. On the wet and dry grinder/sharpener, the lubrication of
the worm drive should be checked after each 50 hours
of operation by an authorised service centre.
Download from Www.Somanuals.co1m2. All Manuals Search And Download.
Carefully read the entire Instruction Manual
before using this product.
With continuing product development changes may
have occurred which render the product received
slightly different to that shown in this instruction
manual. The manufacturer reserves the right to
Before returning this product for a
Warranty Claim or any other reason
Please Call 1300 880 001 (Australia)
or 0800 445 721 (New Zealand)
change specifications without notice. Note:
Specifications may differ from country to country.
When you make your call, please have
the following information at hand:
• GMC Product Type • GMC Product Code
A GMC Service Engineer will take your call and, in
most cases, will be able to solve your problem over
the phone.
The GMC 777 Helpline operates from 7am to
7pm, 7 days a week (EST). This allows you
to contact GMC directly with any queries and
technical questions you have regarding
our products.
You are welcome to use this phone-in service to
make suggestions or give comments about any
GMC product.
45–55 South Centre Road
Melbourne Airport
Victoria, Australia 3045
Tel: (03) 8346 1100 Fax: (03) 8346 1200
Save this Manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
|