25.4CC
COMPACT CHAINSAW
PCH25
INSTRUCTION MANUAL
Code: PCH25
Date: 080318
Black
Cyan
Magenta
Yellow
Edition: 11
Op: DJ
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Description of symbols
Your new GMC power tool will more than satisfy
your expectations. It has been manufactured under
stringent GMC Quality Standards to meet superior
performance criteria.
The rating plate on your tool may show symbols.
These represent important information about the
product or instructions on its use.
Conforms to relevant safety standards.
You will find your new tool easy and safe to operate,
and, with proper care, it will give you many years
of dependable service.
Wear hearing protection.
Wear eye protection.
Wear head protection.
CAUTION. Carefully read through this entire Instruction
Manual before using your new GMC Power Tool. Take
special care to heed the Cautions and Warnings.
Read these instructions for use carefully.
Wear safety footwear.
Your GMC power tool has many features that will make
your job faster and easier. Safety, performance, and
dependability have been given top priority in the
development of this tool, making it easy to maintain
and operate.
Wear safety gloves.
Warning.
Use at a distance of at least 10m
from other people.
Environmental protection
Recycle unwanted materials instead
of disposing of them as waste. All tools,
hoses and packaging should be sorted,
taken to the local recycling centre and
disposed of in an environmentally safe way.
Explosive material.
Extremely hot surface. Do not touch a hot muffler,
gear box or cylinder, you may get burned. These
parts get extremely hot from operation and remain
hot for a short time after the unit is turned off.
WARNING! Danger of kickback.
Do not operate unit in the rain.
Do not attempt to hold saw with one hand.
Do not use the point of the bar.
Hold saw properly with both hands.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Symbols on the machine
Specifications
Fuel inlet.
(Position: under the fuel tank cap.)
Engine displacement:
Maximum engine power:
Engine type:
25.4cc
900W
Chain oil inlet.
(Position: next to the oil tank cap.)
Air cooled, single
cylinder, two-stroke cycle
On/Off.
(Position: on the on/off switch.)
Recommended maximum
engine speed at idling:
Setting the on/off switch to Off, stops the engine
immediately.
3200min-1
Maximum engine speed
with cutting attachment:
Run position.
11000min-1
Start position (when engine is warm.)
Start position (when engine is cold.)
Fuel type:
Unleaded petrol/
2-stroke oil (35:1)
1 Litre of unleaded petrol:
5 Litre of unleaded petrol:
28.5ml of oil
145ml of oil
Choke control
(Position: next to knob on the filter cover)
Fuel tank capacity:
Oil tank capacity:
Spark plug:
230ml
160ml
High run adjustment screw.
Low run adjustment screw.
LD L8RTF NGK BM6A
Champion CJ8
Idle adjustment screw.
(Position: left side of machine close to
pull start handle.)
Oil feeding system:
Sprocket wheel:
Automatic pump
6–teeth x 9.53mm
(3/8”) pitch
Chain brake released (hollow arrow) and
activated (solid arrow.) (Position: right side
of machine, on chain drive cover.)
Guide bar type:
Chain bar length:
Chain type:
Sprocket nose
305mm (12”)
Chinese Chain
9.53mm (3/8”)
Chain pitch:
Weight (including
guide bar and chain):
3.85kg
Sound pressure level:
110 dB(A)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
f) If devices are provided for the connection of dust
extraction and collection facilities ensure that these
are connected and properly used. Use of these
devices can reduce dust-related hazards.
General safety instructions
WARNING. Read and understand all instructions.
Failure to follow all instructions listed below may result
in fire and/or serious injury.
Save these instructions
1) Work area
3) Power tool use and care
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
a) Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b)Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks which
may ignite the dust or fumes.
b)Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
c) Turn tool off completely before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk
of starting the power tool accidentally.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under the
influence of drugs, alcohol, or medication. A moment
of inattention while operating power tools may result in
serious personal injury.
d)Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
b)Use safety equipment. Always wear eye protection.
Safety equipment such as a dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c) Remove any adjusting key or wrench before turning
the tool on. A wrench or a key that is left attached to
a rotating part of the power tool may result in personal
injury.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
d)Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
g)Use the power tool, accessories and tool bits etc.,
In accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power tool
for operations different from intended could result in a
hazardous situation.
e) Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not use the chainsaw in rainy or windy conditions or in
poor light.
4) Service
a) Have your power tool serviced by a qualified repair
personnel using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
• Find a suitable position before beginning work.
• When working on slopes, the saw operator must stand
beside or above the wood to cut, i.e. felled trees.
• Use the chainsaw holding it firmly with both hands.
Additional safety rules for petrol chainsaws
Note. For safety reasons the chainsaw is shipped with the
chain brake fully engaged. This brake must be released
before the saw becomes operational.
• Never cut into the ground.
• Never cut into wire fences.
• Never cut into samplings.
• Make a wedge-shaped cut before felling the tree, then
the felling cut leaving a hinge for the felling direction.
• Beware of any falling branches after felling operations.
• Beware of wood splinters when cutting chopped wood.
• Ensure your chainsaw is suitable for the job.
• Never work above shoulder level or reach out to cut a
branch: ensure you have stable footing at all times.
• Never cut into prepared wood.
• Use the chainsaw to cut only wood.
• Do not operate in a hazardous location. Such areas
include where there is a risk of explosion of petrol fumes,
leaking gas or explosive dust.
• It is advisable to provide a support for the chainsaw
when cutting branches. Do not cut using the bar point
and beware of branches under tension.
• Do not operate in a confined area. Exhaust gases, smoke
or fumes could reach dangerous concentrations.
• Children under 18 must not use chainsaws.
• Protect your tool. This chainsaw is NOT WEATHERPROOF
and should not be exposed to direct sunlight, high
ambient temperature and damp, wet or high humidity
conditions.
• Keep people away from the chainsaw when in use.
• Check the following conditions before beginning work:
– There should be no people in the felling area.
– Make sure there is a second person within
• Take care not to spill fuel. When refuelling the chainsaw
ensure that the motor has been switched off. Prevent the
spilling of fuel as this may also ignite with the hot motor.
Never refuel whilst the engine running.
calling distance.
– The working area should be free from obstacles.
• Wear suitable clothes which do not hinder movement.
• Be careful where you store the chainsaw. Store the tool in
a dry area away from flammable liquids.
• Use specific protection during operations involving head,
hands, feet, eyes and ears.
• Keep your distance. The chainsaw emits exhaust fumes.
Ensure bystanders keep a safe distance.
• It is recommended the use of a helmet with a visor during
felling, branch cutting and chopping operations.
• Operating instructions and instructions for common
cutting tasks, including the use of personal protection
equipment, the need for adequate training and the risks
involved when operating the unit while tired, ill or under
the influence of alcohol or other drugs.
• Wear gloves with an external protection when using the
chainsaw.
• Use ear protection to prevent hearing injuries.
• Wear safety boots when using the chainsaw.
• During transport the brake must be applied to avoid
accidental start-up.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
• Ensure you use oil-mix fuel. Ensure that you mix 35 parts
unleaded fuel to 1 part 2-stroke oil. If not, the engine will
overheat and cause damage to your chainsaw.
DANGER!
BEWARE OF KICKBACK!
WARNING! Kickback can lead to dangerous loss of control
of the chainsaw and result in serious or fatal injury to the
saw operator or to anyone standing close by. Always be
alert. Rotational kickback and pinch kickback are major
chainsaw operational dangers and the leading cause of
most accidents.
• Never fill fuel tank indoors. Never fill fuel tank when
engine is running or hot. Do not smoke when filling
fuel tank.
Kickback safety precautions
• Kickback may occur when the tip of the guide bar
touches an object, or when the wood closes in and
pinches the saw chain.
Unpacking
Due to modern mass production techniques, it is unlikely
that your GMC Power Tool is faulty or that a part is missing.
If you find anything wrong, do not operate the tool until the
parts have been replaced or the fault has been rectified.
Failure to do so could result in serious personal injury.
• If the bar tip or point contacts, it can produce a rapid
reverse reaction, kicking the guide bar up and back
towards the operator. This is known as rotational
kickback.
• Pinching the saw chain along the top of the guide
bar may push the guide bar rapidly back towards the
operator. This is known as pinch kickback.
Contents of carton
The GMC Petrol Chainsaw is supplied with the following
accessories as standard.
• Either of these reactions can cause loss of control of the
saw, resulting in serious personal injury.
•
•
•
•
Chain
• Do not rely exclusively on the safety devices built into
your saw. Take the following steps to help avoid accident
or injury:
Guide bar
Double ended wrench
Screwdriver
• Reduce the element of surprise by understanding what
causes kickback.
• Keep a firm grip on the chainsaw using both hands, the
right hand on the rear handle and the left hand on the
front handle when the motor is running. A firm grip will help
maintain control. Do not let go whilst the motor is running.
• Make sure that the area of operation is free of
obstructions. Do not let the point of the guide bar contact
a log, branch or any other object.
• Use high speeds when cutting.
• Do not overreach or cut above shoulder height.
• Carefully follow the sharpening and maintenance
instructions given in this manual.
• Use only replacement bars and chains specified by the
manufacturer.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Know your product
1. Guide bar
2. Chain
12
20
19
9
8
28
3. Chain tensioning screw
4. Chain drive cover
5. Chain drive cover nut
6. Bucking spikes
7. Air filter
27
8. Front guard (chain brake)
9. Top handle
10. Filter cover
11. Filter cover knob
12. Rear handle
13. Recoil starter
14. Idling adjustment screw
15. HIGH (Fast) run adjustment screw
16. LOW (Slow) run adjustment screw
17. Choke control
4
3
5
21
1
2
18. On/Off switch
19. Trigger switch
13 17
18
11 10
29
14
20. Lock off switch
21. Chain catcher
22. Oil tank cap
23. Fuel tank cap
24. Drive sprocket wheel
25. Spacer (for shipping
purposes only,
please dispose of)
26. Chain tensioner pin
27. Double ended wrench
28. Screwdriver
16 15
29. Priming bulb
6
26
7
22 23
24
25
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Place the guide bar (1) in position over the threaded
stud with the chain tensioning pin (26), in the hole in the
guide bar.
Installing the guide bar and chain
WARNING. The chain has sharp
edges. Use work gloves for safety.
IMPORTANT. Front guard (chain
brake) must be disengaged when
installing the guide bar and chain.
1. Pull the front guard (8) towards
the rear of the saw until there
is a “click” to make sure that
the chain brake is released.
2. Remove the chain drive cover nut (5) with the double
ended wrench (27) and remove the chain drive cover (4).
6. Place the chain (2) around the
drive sprocket wheel (24) with
the chain links in the direction
shown on the bar and fit the
chain around the guide bar.
7. Fit the chain drive cover and
fasten the nut (5), finger tight.
8. Tighten the chain tensioner
screw (3) until the links of the
chain just touch the bottom
edge of the guide bar.
3. Once the chain drive cover (4) has been removed, the
transport- protecting spacer (25) must be removed and
disposed of so that the chain bar can be positively located.
9. Tighten drive nut.
4. Fully loosen the chain tensioning screw (3).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Check that the chain can be
smoothly pulled around the
guide bar by hand and that
it maintains contact with the
guide bar, top and bottom.
To check tension, rotate the
chain to its tightest condition
• Do not run the tank dry, as this will cause damage to
the engine.
����
• Do not use oil meant for 4-stroke engines, it will cause spark
plug fouling, exhaust blocking and piston ring sticking.
�����
�����
• Do not use fuel mixtures that have been left standing for one
month or more, they can cause clogging of the carburettor.
Before storing the chainsaw for an extended period,
empty the fuel tank, clean it then run the motor to empty
the carburettor.
then suspend a 0.9kg weight from the chain at the mid
point of the underside of the bar. The maximum distance
between the driving links and the bar should be 6.5mm.
Note. Do not discard an unwanted fuel container with
household waste. It must be taken to an authorised
repository site.
Note. Ensure the engine is switched off when making any
adjustments to the chain and bar.
CAUTION. A new chain will stretch after just a few minutes
of use. Check and, if necessary, re-adjust the chain tension.
A loose chain causes rapid wear to both the chain and the
guide bar and could derail causing a major safety hazard.
Mixing fuel (35:1 mixing ratio)
1. Measure out the quantities of petrol and oil to be mixed.
2. Put some of the petrol into a clean, approved fuel container.
3. Pour in all of the oil and mix well.
Filling up with fuel and oil
4. Pour in the rest of the petrol and again mix well (at least
one minute).
WARNINGS. Petrol is very flammable. Avoid smoking or
causing any sparks or flames near fuel. Make sure that
you stop the motor and allow it to cool before refuelling the
machine. Select outdoor bare ground for fuelling and move at
least 3m away from the fuelling point before starting the motor.
5. It is very important to mix the two ingredients properly to
prevent unnecessary engine wear.
6. Make sure that the container
is clearly labelled that it is
2-stroke mixture.
• Only use oil that is expressly labelled for use with air-
cooled 2-stroke engines. DO NOT use BIA or TCW
(2-stroke water-cooling type) mixed oil.
Fuelling the chainsaw
The recommended mixing ratio is PETROL 35: OIL 1
1. The engine must be stopped
and cool. Place the chainsaw
on its side with the fuel tank
cap facing upwards.
• Use unleaded petrol with a minimum Octane number of
89. If you use petrol with an Octane number lower than 89,
there is a danger that the engine might overheat and the
piston seize.
2. Make sure that the fuel
mixture is well mixed.
• Poor quality petrol or oil may damage sealing rings, fuel
lines or the fuel tank. Do not use wasted or regenerated
oil, it can damage the oil pump.
3. Remove the fuel tank cap (23).
4. Fill the fuel tank to about 80%
of its capacity.
CAUTION. To maximise the lifetime of the engine, avoid the
following:
5. Fasten the fuel cap securely
and wipe up any fuel spillage
around the machine.
• Do not use raw petrol, it will severely damage the engine
very quickly.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Depress the priming bulb (29)
6 times or when the bulb is full
of fuel.
Note: 1 Litre of unleaded fuel: 28.5ml of oil.
5 Litre of unleaded fuel: 145ml of oil
Adding chain oil
Note. This is not required if
engine is warm or is being
restarted.
WARNING. Never start work
unless the chain and bar are
lubricated.
It returns automatically when the
trigger switch is operated.
1. Place the chainsaw on its
side with the oil cap facing up.
Untwist and remove the oil
tank cap (22).
5. Hold the chainsaw securely on
the ground and pull vigorously
on the recoil starter (13).
Repeat (at least 15 times) until
the engine “kicks” (attempts
to start).
2. Fill the tank to 80% capacity
with chain oil.
3. Fasten the cap and wipe up
any oil spillage.
6. With the lock off switch (20)
held depressed slightly pull on
the trigger switch (19) and then
release it. The choke control will
click back one position.
Starting the chainsaw
WARNING. Do not start the motor whilst the saw hangs
from one hand. This is very dangerous as the chain may
come in contact with your body.
1. Fill the fuel and oil tanks
respectively and tighten the
caps securely.
7. Pull the recoil starter (13)
again and restart the engine.
Allow the engine to warm up.
8. When the engine is warm first
depress the lock off switch
then pull fully on the trigger
switch for a short burst. The choke control will fully retract
to the RUN position, your chainsaw is now ready for use.
2. Set the on/off switch (18) to
On (the I position). Make sure
the brake is ON when starting
for safety, by pushing the front
guard forward.
9. When restarting the engine when it is still warm, set the
choke control to the START
position. Hold the chainsaw
securely on the ground and
3. When the machine is cold first
pull out the choke control (18)
to the CHOKE position. (Fully
withdrawn).
pull vigorously on the recoil starter (13). Allow the
engine to run for a few moments with the trigger switch
pulled slightly.
10. When the engine is fully
warm, pull on the trigger
switch. The choke control will
fully retract to the RUN position.
Note. Once the choke control
has been pulled out, it cannot be
pushed back to the run position.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
11. When ready to start cutting, release the brake, by
pulling the front guard back.
4. Start the engine and let it warm up with the trigger switch
half pulled in. When the engine is warm, release the
trigger switch.
Stopping the chainsaw
1. Release the trigger switch.
2. Set the on/off switch (18) to
Off (the O position).
5. Turn the L screw (17) slowly clockwise until the idling
speed is at its maximum then turn the screw back
(anticlockwise) 1/4 of a turn.
6. Turn the idling adjusting screw (T) (14) anticlockwise until
the chain does not turn.
7. If the idling speed is too slow, turn screw (T) clockwise.
8. Make a test cut and adjust screw (15) for best cutting
power, not for maximum speed.
Checking the oil supply
Run the engine at medium
Chain brake
speed and check that the chain
splatters a thin line of oil which
can be seen on the ground when
the bar is pointed downwards.
This is normal. If there is no
line of chain oil, stop the motor
immediately and investigate the
cause. The oil tank could be
empty or the oil supply to the
chain blocked. This may require
removal of the bar and checking
that the upper oil hole in the bar
is clear of any blockages.
The chain brake operates automatically in the event of
kickback. As the guide bar (1) kicks up, the wrist of the
operator’s hand on the top handle knocks against the front
guard (8) causing the front guard to move forward and
activating the chain brake.
1. The chain brake can be
operated manually by moving
the front guard forward.
2. To release the chain brake,
pull the front guard towards
the top handle until a “click”
is heard.
Adjusting the carburettor
The carburettor is factory set and
should not require adjustment.
Changes in operating conditions
may require fine tuning of the
carburettor. Proceed as follows.
CAUTION. Check that the chain
brake is operating correctly each time the chainsaw is used.
H
L
T
Bucking spikes
The Chainsaw has bucking
spikes (6) to assist with cutting
and reduce the chance of
1. Stop the engine and screw in
both the H and L needles (15)
using screwdriver (28). Do not
force.
kickback, use them as follows:
2. Turn the H screw (15) back 3/4 of a turn.
3. Turn the L screw (16) back 1-1/2 turns.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
take the tool to an authorised repair centre to have the
brake band and clutch drum replaced. Disengage the chain
brake by pulling the front guard backwards until you hear
a click. Do not use the chainsaw if the chain brake is not
operating correctly.
Operation
WARNINGS.
• Always follow the safety instructions given at the front
of this manual. This chainsaw must only be used for
cutting wood. It must not be used for cutting other types
of material. Do not use the chainsaw as a lever for lifting,
moving or splitting objects.
• Be constantly aware of the position of the upper quadrant
of the blade tip. This is the part that triggers a kickback
when it hits resistance.
• Do not attach the chainsaw to a fixed stand.
• Never engage the upper quadrant of the guide bar with
whatever you are cutting and avoid contact with any
hidden branches or obstructions. Ensure there is a clear
work area.
• Do not attach any devices to the chainsaw other than
those specified by the manufacturer.
Helpful hints
• Do not force the saw into the cut. Apply only light pressure
whilst running the engine at full throttle.
• Always clear away brush, vegetation and any obstructing
debris before attempting a cut that might trigger a
kickback.
• If the saw chain gets caught in the cut, do not try to
remove it by twisting the guide or pulling forcibly. Use a
lever or wedge to open up the cut so that the saw chain
is freed.
• Avoid cuts that will cause the chainsaw to jam in a tree
trunk or limb.
• Observe the size of wood shavings, if they become dusty
your chain could need sharpening.
While cutting, always:
Felling a tree
WARNING. Felling a tree should only be done by
• Run the chainsaw motor at full revs. This makes the job
safer, as there is less chance of pull-in or kick-back.
trained operators.
• Position your body to the left of the chainsaw so if it kicks
back uncontrollably, it goes over your right shoulder,
never stand in the cutting line of the saw.
Decide the direction in which
you wish the tree to fall taking
into account the direction
of the wind, the position of
branches, lean of the tree,
ease of subsequent limbing
and bucking and other factors
prevalent at the time.
• Keep a firm grip with your left hand on the front handle,
with your thumb securely below the handle.
• The swivel of your wrist in a kick-back situation will
activate the chain brake.
• Make sure the chain is tensioned correctly.
1. Clear the area around the tree and make sure that you
have a good foothold and clear retreat path.
Guard against kickback
Check the operation of the chain brake each time you use
the chainsaw.
Run the saw at full throttle for 1-2 seconds then push the
front guard (8) forwards. The chain should stop immediately.
If the chain is slow to stop or only slows down you must
2. Ensure that others in the area are aware of the felling
and ensure people and animals are well clear.
3. Make a notch cut one-third of the way into the tree on the
felling side.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Make the felling cut on the opposite side to the initial
notch and slightly higher than the notch. As the felling cut
gets close to the notch cut, the tree will begin to fall.
CAUTION. Avoid cutting into the ground as this will very
quickly dull the saw chain.
Pruning
Pruning is the removal of a limb
5. Remove the saw from the cut, stop the engine with the
on/off switch (18), put the saw down and leave the area
along the retreat path.
2
or branch from a standing tree.
1
WARNINGS. Do not use an
Limbing
Limbing is the process of
removing the branches from
a fallen tree.
1
unstable foothold or ladder. Do
not overreach. Do not saw above
shoulder height. Always use both
hands to hold the saw.
2
Check the direction in which a branch will bend before
cutting it. Always cut on the opposite side to the bending
direction so that the guide bar is not pinched in the cut.
For large limbs that cannot be removed in one cut, make
an initial cut from the bent side and finish by sawing from
the opposite direction. Do not remove limbs that are
supporting the fallen tree on the ground until the tree has
been cut into lengths.
First cut up from the bottom and finish down from the top.
Maintenance
Note. Before cleaning your chainsaw or carrying out any
maintenance procedure, make sure that the engine is off
and is cool. Disconnect the spark plug to prevent
accidental starting.
Maintenance to be preformed after each use
1. Loosen the filter cover knob (11) and remove the filter
cover (10).
WARNINGS. Always keep a balanced stance. Do not stand
on the log. Be alert to the fact that the log may roll over.
When working on a slope, always stand on the uphill side
of the log.
2. Remove the air filter (7).
3. Split the air filter into its two
halves and clean the mesh.
Dry particles can be removed
by tapping on a hard surface.
More stubborn dirt may
require washing out the filter
with petrol or using an air
compressor.
Bucking
Bucking is cutting a log into
lengths for easier handling.
To saw a log lying on the ground,
first saw halfway, then roll the log
over and cut from the opposite
side. To saw the end of a log
supported off the ground, first
1
2
2
1
4. Re-assemble the two halves
and replace the airfilter, filter
cover (10) and knob (11).
saw up from the bottom one-third through the log then finish
by sawing down from the top. To saw a log in the middle of
two supports holding it off the ground, first saw down from
the top one-third through the log then finish by sawing up
from the bottom.
5. Take off the guide bar (1)
and maintain it as follows,
remove any sawdust from the
groove in the guide bar.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Make sure that the oil port is
not clogged. Grease the nose
sprocket at the tip of the
guide bar.
WARNING. Wear heavy
gloves when handling the chain.
Hold the guide bar (1) securely
in a vice.
7. Check for fuel and oil leakage
and loose fastenings,
especially those securing the
handles and the guide bar. If
any defects are found, take
the tool to an authorised
repair centre.
Sharpen each cutter using a
chain file. Always use outward
strokes.
After sharpening, the cutters
must all have the same width and length. After every 3-4
times use an authourised repair centre to professionally
sharpen your saw chain. They have the special tools
necessary to ensure the correct cutting angles and depths.
8. Clean any dust away from the cooling vents as clogged
vents can cause overheating.
Guide bar wear
Chain sharpening
Reverse the guide bar every 8 working hours to ensure
uniform wear. Check the bar rails frequently and if
necessary remove burs and square-up the rails using
a flat file.
Sharpen the chain regularly to maintain optimum
performance of the saw. Signs of a dull chain are:
• The sawdust becomes powder-like
• Extra force is required to execute a cut
• The cut does not track in a straight line
• Increased vibration
• Increased fuel consumption
15
Download from Www.Somanuals.com. All Manuals Search And Download.
GMC customer assist
If your product needs repairing, replacing,
technical service or you simply need help or advice,
please contact us on our Customer Assist Line
1300 880 001 (Australia) or 0800 445 721 (New Zealand).
For prompt service we suggest you log your service request
access to the Internet, please contact our service department
on 1300 880 001 (Australia) or 0800 445 721 (New Zealand).
7am –7pm, 7days a week (AEST).
Please note that if repair or replacement is required,
you must provide a valid original purchase receipt.
You will need the following details at hand to log your service request;
Personal details: First & Last name, address, pick up address,
contact phone numbers, email address
Product details: Product number, date of purchase, retailer bought from,
State & postcode, receipt number, reason for the request,
copy of official purchase receipt
Attach your purchase receipt and save with this Manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
|