Gianni Industries Door DG 30 User Manual

DG-30 Digital Keypad / Proximity Entry system  
Operation User's Manual  
1. Product Characteristic:  
Allows up to 150 Proximity cards / tokens or PIN codes  
Tamper Switch Included  
Door Reed Switch Input for Anti-Trailing  
Fully Programmable via keypad and master code  
Extendable from keypad only to proximity controller  
Supports 26 or 34-bit Wiegand auxiliary reader  
Logical memory to prevent duplication  
Non-Volatile Memory  
Invalid PIN Lock-out  
2. Specifications:  
Operating Voltage: 12 Vdc  
Current Draw: 60mA Max @12VDC  
Input: request-to-exit, time out reed switch contact, auxiliary reader  
Relays Electric Current: 2A MAX @30Vdc 0.4A @ 120Vac  
Memory Volume: 150 PIN codes or 100 Proximity cards/tokens and 50 PIN codes  
Format: 26 or 34-bit Wiegand hexadecimal.  
Relay 1 is controlled by 001~100 user slotsCards or PIN codes)  
Relay 2 is controlled by 101~150 user slotsPIN codes)  
PIN codes: 5 digit codes only  
Case Material: ABS UL94V0)  
Operating Temperature: -20~+70  
Ambient Humidity: 5~95% relative humidity non-condensing  
Visual Signals:  
Red: Power on  
Green: Relay activated  
Tri-color LED:  
Yellow: Program Mode  
Red: The slot is registeredLock-out  
Green: This slot may register the card or PIN codes.  
Factory Master Code: 12345  
Invalid PIN Lock-out: The system will shut down for 60 seconds while 32 codes of  
incorrectly Master Codes enrolled or PIN codes attempted.  
EPROM: Non-volatile memory, System will retain all programs and codes after a total  
loss of power.  
Output: Dual relay, N.O./N.C./Com. Output (free voltage contact) Tamper switch  
Relay Activation Time: (*10、*20)  
Strike Time: 1~99 secondsadjustable)  
Strike mode: Access Timer or Latch  
Color: Dark gray/ Beige White  
Copyright Gianni Industries, Inc. All Rights Reserved.  
P-MU-DG30 Ver. A Publish:2004.08.26  
Page: 1/ 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Followed By 03」:This will set the system to be used as : Slots 001~150 for PIN  
codes only  
Note: When system format has the change, there’s a possibility the card stored would be  
invalid. Please reset the system and input all cards /tokens.  
Add card and deletion  
Enter the Programming mode, Enter the slot position code 001~100」  
A. Green light comes on: This slot position is ready to register the card  
1.  
Present card in front of the readerÆYellow LED blinks (beep) Æ enrolled  
completed Ærepeat)  
2.  
Present card in front of the readerÆ (3 audible beeps) another card has already  
been input (duplicate card).  
B. Red light comes on: This slot already has a code registered  
1.  
Press「**」(deletion) Æ Green light Æ Enter the slot position code again  
ÆPresent the card in front of the reader Æsame as Step “A”﹞  
Enter another slot card position  
2.  
Add PIN codes and deletion  
Enter the Programming mode, Enter the slot position code 101~150」  
A. Green light comes on: This slot position code may register the PIN codes  
Input 5 digit PIN codes ÆYellow LED blinks (beep) Æ enrolled Ærepeat)  
B. Red light comes on: This slot position code is registered  
1. Press「**」(deletion) Æ Green light Æ Press the slot position code again Æ  
Input 5 digit PIN codes Æsame as Step “A”﹞  
2. Enter another slot card position  
Note 1: The codes"12345" or master code are not be used for PIN code.  
Note 2: PIN codes operate open door:「???????????*****#」  
???….random codes,「*****」5 digit PIN codes,「#」Enter  
To Program Relocking Timer  
Enter the Programming mode,  
A. Relay 1Press「*10Followed by the number of seconds the relay should  
open05=5 seconds01 ~99 = secondsbeepenrolled Press  
#to exit from the programming mode, or program other operating.  
B. Enter00Sets the relay to latching mode. (Correct code entered opens the relay,  
and the relay stays open until the correct code is entered again).  
C. Relay 2Press「*20Followed by the number of seconds the relay should  
open05 =5 seconds (01 ~99 = seconds). beepenrolled Press  
#to exit from the programming mode, or program other operating.  
D. Enter00Sets the relay to latching mode. (Correct code entered opens the relay,  
and the relay stays open until the correct code is entered again).  
Changing the Master codes:  
Enter the Programming mode, Enter「*00Followed by the new 5 digit master  
codebeepenrolledEnter #to exit from the programming mode, or  
program other operating.  
Copyright Gianni Industries, Inc. All Rights Reserved.  
P-MU-DG30 Ver. A Publish:2004.08.26  
Page: 3/ 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reset to Factory  
Master Code reset to Factory 12345」  
Insert the jumper RES1Æ 1-2 positionÆ5 audible beepsÆReset successfulÆ Return  
Insert the jumper to 2-3 position  
Remove all stored information  
Insert the jumper RES1Æ 1-2 positionÆ5 audible beepsÆ Master Code reset to  
Factory 12345Æ after 5 secondsÆ5 audible beepsÆ Remove all stored  
information Æ Return Insert the jumper to 2-3 position.  
Note: If you only wish to reset the Master Code to the Factory default, remove the  
jumper after exactly 5 audible beeps, otherwise all cards / codes will be deleted.  
5. Wiring diagram:  
Auxiliary Reader  
(Wiegand 26 or  
34-bit Format)  
Auxiliary Reader  
(Data/CLK Format)  
Tamper  
Switch  
+12V  
GND  
DATA  
CLK  
Contact door reed switch  
BUZZER  
+5V  
This reed switch is used  
to reset the re-locking time  
to 0 second when the door is moved.  
(Using N.O. contact in case of door closed,  
changeover to N.C. When door is moved)  
Push Button  
To follow the  
precedent of  
Group 1 contacts  
FAIL-SAFE  
LOCKING DEVICE  
Power Supply  
1 2 3  
Re-set of all  
system parameter  
Note:  
DG-30 controller and auxiliary reader distance must not exceed 20 meters; the data will  
not transmit beyond this. The suggested wire gauge is #22~26 AWG.  
Using a Linear supply power recommended, to prevent power reduction at the card  
reader.  
The varistor or diode must be connected across the lock terminal (electromagnet...)  
operated by the device. The vartistor controls the overload produced by the strike coil  
(EMP).  
Egresses switch should be N.O. type.  
Copyright Gianni Industries, Inc. All Rights Reserved.  
P-MU-DG30 Ver. A Publish:2004.08.26  
Page: 4/ 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Echo Stereo System P 953 User Manual
Eiki Projection Television EIP 3500 User Manual
Everpure Water System PBS400 User Manual
Fisher Price Car Seat N9327 User Manual
Flymo Trimmer Sabre Trim User Manual
Freedom9 Switch IP 100 User Manual
GE Dishwasher 165D4700P389 49 55065 07 09 JR User Manual
Glen Dimplex Home Appliances Ltd Oven BI 70 90 FP User Manual
Goodman Mfg Air Conditioner DSXC16 User Manual
Goodman Mfg Heat Pump GSZ110903AA User Manual