It is of vital importance, before attempting to
operate your engine, to read the general
'SAFETY INSTRUCTIONS AND WARNINGS'
section on pages 2-5 of this booklet and to strictly
adhere to the advice contained therein.
●
Also, please study the entire contents of this
instruction manual, so as to familiarize yourself
with the controls and other features of the
engine.
●
Keep these instructions in a safe place so that
you may readily refer to them whenever
necessary.
●
It is suggested that any instructions supplied
with the vehicle, radio control equipment, etc.,
are accessible for checking at the same time.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
SAFETY INSTRUCTIONS AND
WARNINGS ABOUT YOUR O.S. ENGINE
16
16~17
17~18
IF THE ENGINE FAILS TO START
FINAL ADJUSTMENT
2
~
5
6
8
9
INTRODUCTION, BASIC ENGINE PARTS
INSTALLATION
CARBURETTOR CLEANLINESS
7
~
~
19
CARE AND MAINTENANCE
AIR CLEANER TYPE102
8
EXPLODED VIEW &
ENGINE PARTS LIST
NOTES CONCERNING
THE RECOIL STARTER
20~23
24~25
9~10
CARBURETOR EXPLODED VIEW
& PARTS LIST
10~11
GLOWPLUG
11~12
TOOLS, ACCESSORIES, etc.
O.S. GENUINE PARTS &
ACCESSORIES
26
27
CARBURETTOR CONTROLS
PRESSURIZED FUEL SYSTEM
12~13
13
THREE VIEW DRAWING
STARTING THE ENGINE &
RUNNING-IN('Breaking-in)
14~15
1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS AND WARNINGS ABOUT YOUR O.S. ENGINE
Remember that your engine is not a "toy", but a highly efficient internal-
combustion machine whose power is capable of harming you, or others, if it is
misused.
As owner, you, alone, are responsible for the safe operation of your engine, so act
with discretion and care at all times.
If at some future date, your O.S. engine is acquired by another person, we would
respectfully request that these instructions are also passed on to its new owner.
The advice which follows applies basically to ALL MODEL ENGINES and is
grouped under two headings according to the degree of damage or danger
which might arise through misuse or neglect.
WARNINGS
NOTES
These cover the many other
possibilities, generally less obvious
sources of danger, but which, under
certain circumstances, may also
cause damage or injury.
These cover events which
might involve serious (in
extreme circumstances, even
fatal) injury.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNINGS
•
•
Never operate your engine in an en-
closed space. Model engines, like
automobile engines, exhaust deadly
carbon-monoxide. Run your engine
only in an open area.
Model engine fuel is poi-
sonous. Do not allow it to
come into contact with the
eyes or mouth. Always
store it in a clearly marked
container and out of the
reach of children.
Model engines generate
considerable heat. Do not
touch any part of your
engine until it has cooled.
Contact with the muffler
(silencer), cylinder head
or exhaust header pipe, in
particular, may result in a
serious burn.
•
Model engine fuel is also
highly flammable. Keep it
away from open flame,
excessive heat, sources of
sparks, or anything else
whichmightigniteit. Donot
smoke or allow anyone else
to smoke, near to it.
•
3
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
This engine is intended for model cars.
Do not attempt to use it for any other
purpose.
•
•
• The wearing of safety glasses is also
strongly recommended.
Take care that the glowplug clip or
battery leads do not come into contact
with rotating parts. Also check that the
linkage to the throttle arm is secure.
•
•
Mount the engine in your model
securely, following the manufacturers'
recommendations, using appropriate
screws and locknuts.
For their safety, keep all onlookers
(especially small children) well back
(at least 20 feet or 6 meters) when
preparing your model for running.
• Fit an effective silencer (muffler).
Frequent close exposure to a noisy
exhaust (especially in the case of the
most powerful highspeed engines)
may eventually impair your hearing
and such noise is also likely to cause
annoyance to others over a wide area.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
•
To stop the engine, fully retard the
•
Pull the operating handle straight out
when starting the engine, so that the
cord does not rub against the vehicle
body or engine. This will help prevent
the cord from being damaged by
abrasion or engine heat.
throttle stick and trim lever on the
trans-mitter, or, in an emergency, cut
off the fuel supply by pinching the fuel
delivery tube from the tank.
• Do not attempt to disassemble the
recoil starter of the 15CV-X.
•
Warning! Immediately after a glowplug-
ignition engine has been run and is still
warm, conditions sometimes exist
whereby it is just possible for the engine
to abruptly restart if it is rotated over
compression WITHOUT the glowplug
battery being reconnected.
If you do so, the very strong spring
inside will be suddenly ejected. This
can be very dangerous.
• Do not extend the starter cord more
than 45cm (18"). Do not abruptly
release the operating handle. Allow
the cord to rewind smoothly while
still holding the handle.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The MAX-12CV and MAX-12CV-X are
high-performance engines for 1/10
class R/C racing cars. The MAX-12CV-X
is equipped with a built-in recoil starter
system which eliminates the need for a
separate electric and starter battery.
BASIC ENGINE PARTS
Heatsink Head
Carburetor
Starter Handle
NOTE:
With this engine, the piston will feel tight at
the top of its stroke when the engine is cold.
This is normal. The piston and cylinder are
designed to achieve a perfect running
clearance when they reach their normal
running temperatures.
INSTALLING THE GLOWPLUG
Fit washer to glowplug and
insert carefully into cylinder-
head, making sure that it is
not cross-threaded
Recoil Starter
Assembly No.5
Beam Mount
Crankcase
Drive Hub
before tightening firmly.
Glow plug
Crankshaft
MAX-12CV-X
Washer
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Avoid forcing the screws. Secure with locknuts.
If the bottom of the recoil starter housing would
otherwise touch the car chassis, fit the engine
mount spacers (supplied) between the engine's
mounting lugs and the engine mount. Use the
M3x15 screws provided. With some vehicles, it
may be necessary to make minor trimming
modifications to chassis or body when fitting the
engine.
ENGINE INSTALLATION
Make sure that the vehicle's engine mounting
surfaces are level and in the same plane. Poor
installation may cause distortion of the
crankcase, bearings, etc., resulting in erratic
running and loss of performance.
The recommended screws for securing the
engine are 3mm or 4-40 steel Allen hexagon
socket type.
If existing holes in the engine mount do not align
perfectly with engine mounting lugs, enlarge
them slightly with a needle-file so that screws
enter vertically.
NOTE:
Where spacers are supplied joined in pairs
(see sketch) separate them as shown.
Either face may be placed downwards.
Mount Spacer
Separate
Chassis
Chamfer inside edges of bearers.
Engine Mount
Engine Mount Spacer
7
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR CLEANER TYPE 102
This is a heavy-duty wet type air cleaner that has
been developed specifically for the O.S. MAX-CV
series model car engines.
It contains specially impregnated filter elements which
prevent highly damaging dust and dirt from being
drawn into the engine through the carburetor, yet
allow engine performance to be maintained for longer
periods between element renewals. The Type 102 air
cleaner has a special rubber body which facilitates
easy yet secure fitting, with positive sealing at the
carburetor air intake.
INSTALLATION OF THE CARBURETOR
As delivered, the engine has its carburetor
lightly fit into the intake boss. Secure it as
follows.
1. Loosen the retainer screw, rotate the
carburetor to its correct position and make
sure that it is pressed well down into the
intake boss, compressing the rubber gasket,
before retightening screw.
Rotate the retainer screw gently until it
stops, then tighten a further 60-90˚.
Do not overtighten the screw as this will
damage the carburetor body.
2.
INSTALLATION OF AIR CLEANER
Carefully clean the carburetor,
•
removing any old adhesive or
sealant that may have been
previously used on the outside
of the air intake.
Rotate the retainer nut
gently until it stops.
Tighten a further 60-90˚
Press the air cleaner body firmly
•
over the carburetor air intake. Make sure that the
outer rim of the air intake engages the internal
annular groove in the air cleaner: failure to do so
may result in the air cleaner falling off. See sketch,
right.
ー8ー
Download from Www.Somanuals.com. All Manuals Search And Download.
Position the air cleaner correctly, so that it does not
foul the cylinder-head or obstruct the needle-valve.
Always remove contaminated elements carefully, to
ensure that dirt cannot enter the carburettor.
•
AIR CLEANER ELEMENTS
NOTES CONCERNING THE RECOIL STARTER
Replacement elements
arealreadyimpregnated
with filter oil. As this oil is
very sticky, take cere,
whenhandlingelements
to prevent dust or dirt
from adhering to them. If
your fingers become
Upper Filter
Element
Lower Filter
Element
•
( 12CV-X ONLY)
REMINDER!
◆
◆
◆
Do not attempt to disassemble the recoil
starter. If you do so, the very strong
spring inside will be suddenly ejected.
This can be very dangerous.
Insert beneath flanges.
Do not extend the starter cord more than
45cm(18"). Do not abruptly release the
operating handle. Allow the cord to rewind
smoothly while still holding the handle.
Pull the operating handle straight out
when starting the engine, so that the cord
does not rub against the vehicle body or
engine.
contaminated, wash them with soap and water.
During storage, the oil may have become unevenly
dispersed through the elements. This will be indicated
if the blue colour of the element material appears
patchy. In this case, place the elements in a small
plastic bag and gently rub them between finger and
thumb to redistribute the oil.
•
REPLACEMENT OF ELEMENTS
◆
This will help prevent the cord from being
damaged by abrasion or engine heat.
It is advisable to replace the upper filter element with
•
a new one after not more than one hour of running
time. It is not necessary to discard the lower element
as frequently, but be sure to change it when it
becomes soiled.
◆ Try to avoid spilling fuel over the starter
unit and its cord. Some fuels have a
detrimental effect on these parts.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
The role of the glowplug
◆
The starter prevents the engine from being
rotated in the wrong direction.The unit will
be damaged if you attempt to force the
flywheel in the opposite direction (i.e.
clockwisewhenviewedfromthecrankshaft
With a glowplug engine, ignition is initiated by the
application of a 1.5-volt power source. When the
battery is disconnected, the heat retained within the
combustion chamber remains sufficient to keep the
plug filament glowing, thereby continuing to keep the
engine running. Ignition timing is 'automatic' : under
reduced load, allowing higher rpm, the plug becomes
hotter and, appropriately, fires the fuel/air charge
earlier; conversely, at reduced rpm, the plug become
cooler and ignition is retarded.
NOTE:
Because, in the interests of personal safety,
dismantling of the starter mechanism is
strongly discouraged, the Recoil Starter is
available for replacement only as a pre-
assembled unit.
Glowplug life
Particularly in the case of very high performance
engines, glowplugs must be regarded as expendable
However, plug life can be extended and engine
performance maintained by careful use, i.e.:
However, some related parts, such as
Starting Shaft and Rear Adaptor, are
obtainable separately. (See Parts List.)
Install a plug suitable for the engine.
•
GLOWPLUG
Use fuel containing a moderate percentage of
nitromethane unless more is essential for racing
events.
Since the compatibility of glowplug and fuel may have
a marked effect on performance and reliability, it may
be worthwhile to choose the R/C type plug found
most suitable after tests.Recommended O.S. plugs
are A3, A5 and No8. Carefully fit plug finger-tight,
before final tightening with the correct size plug
wrench.
•
Do not run the engine too lean and do not leave the
battery connected while adjusting the needle.
•
10
Download from Www.Somanuals.com. All Manuals Search And Download.
When to replace the glowplug
As a starting point, we recommend a fuel containing 10-
20% nitromethane, changing to a fuel containing more
nitro only if necessary. When the nitro content of the fuel
isincreasedorthebrandoffuelischanged,itisadvisable
to initially run the engine with a richer needle-valve
setting, so that the optimum setting for the new fuel may
be rechecked as described in the RUNNING-IN
paragraphs. When engines are run at very high speeds
and on high-nitro fuels, glowplug elements do not last
so long.
Apart from when actually burned out, a plug may
need to be replaced because it no longer delivers its
best performance, such as when:
Filament surface has roughened and turned white.
•
Filament coil has become distorted.
•
Foreign matter has adhered to filament or plug
•
body has corroded.
Engine tends to cut out when idling.
•
Starting qualities deteriorate.
•
Rem inder!
Model engine fuel is poisonous. Do not
allow it to come into contact with the eyes or
mouth. Always store it in a clearly marked
container and out of the reach of children.
TOOLS, ACCESSORIES, etc.
The following items are necessary for operating the
engine.
FUEL
Model engine fuel is also highly flammable.
Keep it away from open flame, excessive heat,
sources of sparks, or anything else which
might ignite it.
Use only top quality methanol-based model engine
fuel.For consistent performance and long engine life,
it is advisable to use fuel containing AT LEAST 18%
lubricant.Thisengineisdesignedtorunonbothlowand
high nitromethane content fuels,i.e. from mild mixtures
containing a few percent of nitromethane, up to high-
speed racing fuels containing 40% nitromethane.
Generally,poweroutputisincreased-uptoacertainpoint-
as the nitromethane content of the fuelis increased.
BATTERY INTEGRATED GLOWPLUG HEATER
Commercialy available handy
glowplug heater in which the
glowplug battery and battery
leads are integrated.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRIC STARTER AND STARTER BATTERY
Use an electric starter with 12-volt
battery for starting the MAX-12CV.
(
)
CARBURETOR CONTROLS 10C
Three adjustable controls are provided on this
carburetor.
¡
The Needle-Valve:
For adjusting the mixture strength when the throttle
LONG SOCKET WRENCH
is fully open.
¡
Recommended for easy removal
and replacement of the angled
and recessed glowplug, the
O.S.Long Socket Wrench
incorporates a special grip.
The Mixture Control Screw:
For adjusting the mixture strength at part-
throttle and idling speeds, to obtain steady
idling and smooth acceleration to mid speeds.
¡
The Throttle Stop Screw:
For setting the minimum idling speed.
FUEL BOTTLE OR PUMP
NOTE:
Needle Valve
Ball Link
For filling the fuel tank, a simple,
polyethylene "squeeze" bottle,
with a suitable spout, is required.
Readjustment may
be necessary, occa-
sionally to allow for
changes in fuel for-
mulae, gear ratio or
clutch engagement
SILICONE TUBING
Heatproof silicone tube of approx.
5mm o.d. and 2mm i.d. is required
for the connection between the fuel
tank and engine.
Throttle
Stop Screw
point.
Mixture Control Valve
Assembly Screw
12
Download from Www.Somanuals.com. All Manuals Search And Download.
(
)
CARBURETOR CONTROLS 10E-R
PRESSURIZED FUEL SYSTEM
The somewhat violent changes of vehicle attitude
Three adjustable controls are provided on this
carburetor.
•
that occur in off-road running, combined with the
fact that, in buggy type cars, the fuel tank is often
located some distance from the carburetor, means
that fuel 'head' at the carburetor can vary and upset
running.Therefore,it is recommended that a muffler
pressurized fuel feed system be used.
¡
The Needle-Valve:
For adjusting the mixture strength when the throttle
is fully open.
¡
The Mixture Control Screw:
For adjusting the mixture strength at part-
throttle and idling speeds, to obtain steady
idling and smooth acceleration to mid speeds.
Never run your vehicle without fitting the air cleaner.
Dust and dirt that may otherwise be drawn into the
engine will rapidly shorten its life.
•
¡
The Throttle Stop Screw:
For setting the minimum idling speed:
Connect suitable length of
Fuel Tank
Silicone tubing between fuel
tank and silencer.
NOTE:
Readjustment may
Needle Valve
Silicone tube
be necessary, occa-
sionally to allow for
changes in fuel for-
mula, gear ratio or Throttle
Stop Screw
clutch engagement
point.
Silencer
Mixture Control Valve
Assembly Screw
13
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING THE ENGINE & RUNNING-IN ('Breaking-in')
The following procedure is suitable for these engines
when the O.S. T-1020 tuned silencer and a fuel
containing up to 30% nitromethane are used.
◆
In case of the 10E-R caburettor
approx 1mm
Set the throttle-stop screw so
that the minimum throttle
opening (idle setting) is
approximately 1.0mm.
•
Use the same fuel as is to be employed for all initial
running and containing NOT LESS THAN 18%
lubricant.
•
DO NOT energize glowplug,
but apply electric starter to
draw fuel to carburettor.
•
•
Throttle Stop Screw
Front
Temporarily remove the glowplug to check that it
glows bright red when energized.
•
Re-check the needle-valve
•
Now connect glowplug battery
lead to heat the plug filament
and start the engine.
Close
Rear
and throttle settings. Turn
the needle-valve clockwise
slowly and gently until it
stops. This is the fully
Rotating
Direction
In case of the 12CV-X
◆
Open
Needle Valve
closed position.Do not use
Push the choke button on
•
force to turn the needle-valve beyond this point.
Open the Needle-Valve 2 turns from the fully closed
position.
the fuel tank several times
to deliver the fuel to the
carburetor. (Do not over-
prime or the recoil starter
cannot be pulled.)
•
Approx. 0.3-0.5mm
◆ In case of the 10C caburettor
Switch on the transmitter and
•
receiver and set the throttle
very slightly opened from the
idling position.
Pull the starter handle
briskly straight out several
times to start the engine.
•
Starter Handle
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Remember!
Repeat this procedure until 5 more tanks of fuel have
been consumed, during which time the throttle may
be opened for brief bursts of increased power. If the
engine stops at medium speeds, close the Mixture
Screw 45-90˚.
It is vitally important to set the
throttle at the correct position
before attempting to start the
engine.If the engine is
allowed to run with the
throttle too far open under
"no load" conditions, it will
rapidly overheat and may be seriously damaged.
The position of the needle-valve
when starting the engine.
Needle
Close the needle-valve approx.
30˚ after running the vehicle for
one full tank of fuel.
Repeat this procedure several
times.
Whentheenginestarts, firstallowittooperateinshort
•
runsattheveryrichstartingsettings,withtheglowplug
batterystillconnectedandwithitsdrivingwheelsclear
of the ground.The rich mixture will, under these
conditions, provide adequate lubrication and cooling,
indicated by profuse smoke from the exhaust.
To stop the engine, close the throttle to idling speed,
•
then shut it off completely with the trim lever on the
transmitter. To cut off the fuel supply, pinch the fuel
delivery tube to the carburetor.
Next, disconnect the glowplug battery and try
•
Remember!
running the car on the track. If the engine stalls, open
the throttle fractionally, but try to keep the engine
running as rich as possible: if it stops because of
being excessively over-rich, close the Needle-Valve
30˚ and try again.
If the engine should need to be disassembled (e.g.
for cleaning or minor parts replacement) it is
advisable to return the Needle-Valve to the original
rich, starting setting and check whether further
running-in time is required before the car is raced
again. In the event of any major working parts (e,g,
piston/cylinder liner assembly) being replaced, the
complete running-in should be repeated.
Run the car on the track until one tank of fuel has been
consumed, then close the Needle-Valve 30˚ and run
the car for another full tank of fuel.
•
15
Download from Www.Somanuals.com. All Manuals Search And Download.
FINAL ADJUSTMENT
IF THE ENGINE FAILS TO START
Check the following:
Run the vehicle (with throttle fully open) over the
•
longest available straight course, in order to observe
the model's speed. Next return the car to the starting
point, close the Needle-Valve 30˚ and repeat the
run, taking note of the improvement in performance.
Continue with further runs, gradually reducing the
Needle-Valve setting and aiming to achieve the
highest straight-line speed. Remember, however,
that, if the Needle-Valve is shut down too far, the
engine will overheat and, accompanied by visibly
diminished exhaust smoke, the model will lose
speed. At this point, throttle down immediately, stop
the vehicle and reopen the Needle-Valve 30˚.
Glowplug battery discharged or glowplug defunct.
•
Fuel not reaching carburetor.
•
Engine flooded. Do not over-prime. (This could also
•
cause hydraulic lock and damage the engine on
application of the electric starter.)
Remove glowplug, close needle-valve and apply
starter to pump out surplus fuel. At this time cover
the plug hole with a rag so that splashing fuel will
not get into your eyes or mouth.
MAX-12CV-X
Having established the optimum Needle-Valve
setting, check the Mixture Control Valve setting as
follows.
•
With the engine running, close the throttle and allow
•
it to idle for about five seconds, then reopen the
throttle fully. If, at this point, the engine puffs out an
excessive amount of smoke and the vehicle does
not accelerate smoothly and rapidly, it is probable
that the idling mixture is too rich.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
In this case, turn the Mixture Control Valve
clockwise 45~90˚. If, on the other hand, the engine
tends to speed up momentarily and then cut out
abruptly when the throttle is opened,the idling
mixture is too lean. Correct this by turning the
Mixture Control Valve counter-clockwise 45~90˚.
With the optimum mixture control position, light
smoke is visible during high speed running,and the
engine revolutions increase smoothly during
acceleration. Remember that, if the engine is
operated with the fuel/air mixture slightly too lean, it
will overheat and run unevenly. As with all engines,
it is advisable to set both needle-valve and mixture
control screw very slightly on the rich side of the best
rpm setting, as a safety measure.
•
•
NOTE:
Mixture Control Valve adjustment should be made
in steps of not more than 45~90˚, carefully
checking the effect,on throttle response, of each
small adjustment.
If the engine runs too fast with the throttle closed,
the throttle stop screw should be turned counter-
clockwise to allow the throttle opening to be
reduced.
•
•
Carry out adjustments patiently, under actual
running conditions, until the engine responds
quickly and positively to the throttle control.
•
Finally, beyond the nominal break-in period, a slight
readjustment toward a leaner needle setting may be
required to maintain performance.
Warning!
Mixture adjustments (whether via the Mixture
Control Valve, or the Needle-Valve) cannot be
made accurately under 'no-load' conditions,
which, in any case, are not advised, since such
operation carries the risk of seriously damaging
the engine through over-revving and overheating.
CARBURETOR CLEANLINESS
The correct functioning of the carburetor depends on
its small fuel orifices remaining clear.
(See Care and Maintenance section on Page19.)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
In case of the 10C caburetor
BALL LINK AND SLIDE VALVE EXTENSION
(In case of the 10C caburetor)
■
First rotate the Mixture Control
It is seldom necessary to separate the slide-valve
extension from the slide-valve itself. For cleaning,
withdraw this complete sub-assembly from the
carburetor body after removing the slide-valve guide
screw. Then wash with methanol or glow-fuel.
(Note: take care not to lose the guide screw;it is a
special one.)
Valve until its slotted head is
flush with the carburetor body.
Then screw the valve in exactly
2.5 turn.
This is the standard position.
When it is necessary to adjust the ball-link position,
loosen the ball-link retaining screw with a 2.5mm
hexagon key, re-align the ball-link and re-tughten the
screw firmly.
Mixture Control Valve
Carburettor Body
In case of the 10E-R caburetor
REALIGNMENT OF MIXTURE CONTROL VALVE
■
First rotate the Mixture Control
Throttle Lever
In the course of making carburetor adjustments, it is
just possible that the Mixture Control Valve may be
inadvertently screwed in or out too far and thereby
moved beyond its effective adjustment range.Its basic
position can be found by first rotating the Mixture
Control Valve until its slotted head is flush with the
carburetor body. The valve is then screwed in exactly
2.5 turn to re-establish its neutral position.
Valve until its slotted head is
flush with the carburetor body.
Then screw the valve in
exactly 0.5 turn.
This is the standard position.
Mixture Control Valve
Carburettor Body
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Then, inject some after-run oil into the engine, and
rotate the engine with an electric starter for 4 to 5
seconds to distribute the oil to all the working
parts.
4.
CARE AND MAINTENANCE
1.
The minute particles of foreign matter, that are
present in any fuel may, by accumulating and
partially obstructing fuel flow, cause engine
performance to become erratic and unreliable.
O.S. 'Super-Filters' (large and small) are available,
as optional extras, to deal with this problem.
Note:
Do not inject after-run oil into the carburetor as
this may cause the O-rings inside the carburetor
to deteriorate. These procedures will reduce the
risks of starting difficulties or corrosion after a
period of storage.
One of these filters, fitted to the outlet tube inside
your refueling container, will prevent the entry of
foreign material into the fuel tank. It is also
recommended that a good in-line filter be installed
between the tank and carburetor.
Finally, when cleaning the exterior of the engine,
use methanol or kerosene. Do not use gasoline or
any solvent that might damage the silicone fuel
tubing.
5.
Do not forget to clean the filters regularly to remove
dirt and lint that accumulate on the filter screens.
Also, clean the carburetor itself occasionally.
2.
3.
Caution:
The rear crankshaft bearing of this engine uses a
special plastic retainer. If the front housing needs
to be heated to remove or replace the bearing, do
not allow the bearing to exceed 120˚C (248˚F),
otherwise it may be damaged and rendered
unserviceable.
At the end of each operating session, drain out any
fuel that may remain in the fuel tank.
Afterwards,energize the glow-plug and try to restart
the engine, to burn off any fuel that may remain
inside the engine. Repeat this procedure until the
engine fails to fire. Do this while the engine is still
warm.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MAX-12CV EXPLODED VIEW
C.M2.6x12
2
1
t
e
3
C.M2.6x7
4
6
5
r
w
8
q
7
=
-
0
9
…
…
…
Type of screw C Cap Screw M Oval Fillister-Head Screw
✽
…
…
F
Flat Head Screw N Round Head Screw S Set Screw
Download from Www.Somanuals.com. All Manuals Search And Download.
MAX-12CV ENGINE PARTS LIST
Description
No.
Code No.
(
)
2 1404 300
Heatsink Head RED
(
)
2 1404 310 Heatsink Head GREY
1
(
)
2 1404 320 Heatsink Head BLUE
(
)
2 1404 330
Heatsink Head NATURAL
(
)
2 1404 000 12CV Machine Head GOLD
2
3
4
5
6
7
8
9
0
-
2 1203 011
Cylinder & Piston Assembly
2 1206 000 Piston Pin
2 1205 040 Connecting Rod
(
)
2 1286 000 Carburettor Complete Type 10C
(
)
2 1481 020 Carburettor Complete Type 10E-R
2 1481 700 Carburettor Retainer
2 0810 007
Propeller Nut
2 1408 000 Drive Hub
2 2631 019
(
)
Crankshaft Ball Bearing Front
(
)
2 1401 000 Crankcase RED
(
)
2 1401 010 Crankcase GREY
=
(
)
2 1401 020 Crankcase BLUE
(
)
Crankcase NATURAL
2 1401 030
(
)
2 1230 000 Crankshaft Ball Bearing Rear
q
w
e
2 1202 010
2 1214 000
2 1407 000
Crankshaft
Gasket Set
(
)
Cover Plate RED
(
)
2 1407 010 Cover Plate GREY
r
t
(
)
2 1407 030 Cover Plate NATURAL
2 1213 000
Screw Set
7 1605 300 Glow Plug A3
7 2403 200 Super Air Cleaner 102 W/3 filter elements
(
)
102 Cleaner Body
101,102 Filter Elements 6pcs.
7 2403 210
7 2403 120
(
)
The specifications are subject to alteration for improvement without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAX-12CV-X EXPLODED VIEW
C.M2.6x12
2
1
e
3
y
4
6
5
M.M2.6x7
w
8
q
7
=
-
0
9
u-1
u-2
M.M2.6x7
u
t
r
…
…
…
Type of screw C Cap Screw M Oval Fillister-Head Screw
✽
…
…
F
Flat Head Screw N Round Head Screw S Set Screw
Download from Www.Somanuals.com. All Manuals Search And Download.
MAX-12CV-X ENGINE PARTS LIST
Description
)
No.
Code No.
2 1404 300
(
Heatsink Head RED
(
)
2 1404 310 Heatsink Head GREY
1
(
)
2 1404 320 Heatsink Head BLUE
(
Heatsink Head NATURAL
)
2 1404 330
(
)
2
3
4
5
6
7
8
9
0
-
2 1404 000 12CV Machine Head GOLD
2 1203 011
2 1206 000 Piston Pin
Cylinder & Piston Assembly
2 1205 040 Connecting Rod
(
)
2 1286 000 Carburettor Complete Type 10C
(
)
2 1481 020 Carburettor Complete Type 10E-R
2 1481 700 Carburettor Retainer
2 0810 007
Propeller Nut
2 1408 000 Drive Hub
2 2631 019
(
Crankshaft Ball Bearing Front
)
(
)
2 1401 000 Crankcase RED
(
)
2 1401 010 Crankcase GREY
=
(
)
2 1401 020 Crankcase BLUE
(
Crankcase NATURAL
)
2 1401 030
(
)
q
w
e
r
t
y
u
2 1230 000 Crankshaft Ball Bearing Rear
2 1202 000 Crankshaft
2 1214 000 Gasket Set
Starting Shaft
2 1421 200
2 1421 100 Rear Adaptor
Screw Set
2 1313 030
7 3003 000
7 3003 100
7 3003 200
7 2404 000
No.5 Recoil Starter Assembly
No.5 Recoil Starter Body
No.5 One-way Clutch
Engine Mount Spacer
u-1
u-2
7 1605 300 Glow Plug A3
7 2403 200 Super Air Cleaner 102 W/3 filter elements
(
)
102 Cleaner Body
(
101,102 Filter Elements 6pcs.
7 2403 210
7 2403 120
)
The specifications are subject to alteration for improvement without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
10C CARBURETOR EXPLODED VIEW & PARTS LIST
No.
Description
Mixture Control Valve Assembly
"O" Ring(L) (2pcs.)
Code No.
3-1
2 1285 600
1
2
3
1-1 4 6066 319
2 2781 800
2 1285 640
"O" Ring(S) (2pcs.)
1-2
2
Throttle Stop Screw
2 1285 901 Needle Valve Assembly
3
4
2 7881 820
2 1286 100
2 1285 220
2 1286 200
2 1286 400
2 1881 320
3-1
4
"O" Ring (2pcs.)
Carburetor Body
5
1-1
1-2
5
Slide Valve Guide Screw
Slide Valve
1
6
Metering Needle Assembly
Dust Cover
6
7
C.M3.5x8
8
0
7
9
2 3818 420 Ball Link No.4
2 2615 000
0
Carburettor Rubber Gasket
8
The specifications are subject to alteration for improvement
without notice.
9
Type of screw
✽
…
…
C
Cap Screw M Oval Fillister-Head Screw
…
…
…
F
Flat Head Screw N Round Head Screw S Set Screw
24
Download from Www.Somanuals.com. All Manuals Search And Download.
10E-R CARBURETOR EXPLODED VIEW & PARTS LIST
No.
Description
Mixture Control Screw
"O" Ring (2pcs.)
Code No.
1
2 1481 600
0-1
1-1
2
2 7881 820
2 1481 420
2 2681 419
2 1283 210
2 1481 200
2 2481 506
2 1283 962
2 4881 824
2 1283 961
2 1481 120
2 2681 310
2 1481 900
2 7881 820
2 1481 950
0
9
Throttle Lever Fixing Nut
3
Throttle Lever
Dust Cover
4
6
0-2
5
Carburetor Rotor
Rotor Spring
6
8
7
Nozzle Assembly
"O" Ring
7-1
7-1
7-2
8
Locknut
-
7-2
Carburetor Body
Throttle Stop Screw
Needle Valve Assembly
7
9
0
1-1
0-1
0-2
-
2
"O" Ring (2pcs.)
Fuel Inlet
1
3
2 2615 000 Carburetor Rubber Gasket
4
The specifications are subject to alteration for improvement
without notice.
5
25
Download from Www.Somanuals.com. All Manuals Search And Download.
O.S. GENUINE PARTS & ACCESSORIES
RACING ENGINE PARTS
Exhaust Header Pipes
■
12CV
■
O.S. Glow Plug
10C Automatic
Carburettor
(21286000)
■
■
No.8
Machine Head
BLUE (72001110)
For Kyosho Super10
For Tamiya TGX
(71608001)
(72103120)
(72103110)
A3
For Tamiya TG10
(72001100)
For Kyosho V-ONE R,S
RED
(71605300)
(72103130)
(72103160)
A5
(71605100)
For Kyosho Spider &
HPI Nitro (72103140)
Super Air Cleaner 102S
■
(72403202)
For Mugen MTX
101,102 Filter Elements
■
(72103150)
(6pcs.)
(72403120)
T-1020
Tuned Silencer
Super Joint Tube 15
■
(72103310)
Long Socket Wrench
With Plug Grip
■
■ Dust Cap Set
■
φ
3
(73300305)
For Carburettor Nipple
(71521000)
(72103020)
φ
7
(73300712)
For T-1020 Tuned
Silencer
Crankshaft Clamp
1012
■
φ
10
(73301012)
For 10C,10E-R
Carburettor
(71530100)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
12CV,12CV-X THREE VIEW DRAWING Dimensions(mm)
38
SPECIFICATIONS
11
35.5
■ Displacement
■ Bore
2.11 cc(0.129cu.in.)
14.0 mm(0.551in.)
■ Stroke
13.7 mm(0.539in.)
■ Practical R.P.M.
■ Power output
■ Weight
3,000~30,000 r.p.m.
0.56 bhp / 29,000 r.p.m.
211g(7.45oz.)12CV
M5x0.8
269g(9.50oz.)12CV-X
190g(6.70oz)12CV Hyper
248g(8.75oz)12CV-X Hyper
27.5
41
33.5(17.6)
90.6(74.6)
25
39
40
( )-12CV
27
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
28
Download from Www.Somanuals.com. All Manuals Search And Download.
R
D
6-15 3-Chome Imagawa Higashisumiyoshi-ku
Osaka 546-0003, Japan
TEL. (06) 6702-0225
FAX. (06) 6704-2722
C
Copyright 2000 by O.S.Engines Mfg. Co., Ltd. All rights reserved. Printed in Japan.
120104
Download from Www.Somanuals.com. All Manuals Search And Download.
|