Am p li DECT1 5 0
GB
F
User guide p.2
Notice d’utilisation p.30
CAUTION:THIS TELEPHONE PRODUCT IS ATTENTION:CE TELEPHONE PEUT ETRE DESTINE
SPECIFICALLY DESIGNED FOR PEOPLE WITH HEARING
DIFFICULTIES AND IS PROVIDED WITH A HANDSET
EARPIECE WITH VOLUME CONTROL FOR INDIVIDUAL
REQUIREMENTS. DUE CARE MUST BE TAKEN BY ALL
USERS THAT THE HANDSET EARPIECE VOLUME
CONTROL IS SET TO THE LOWEST LEVEL ACCEPTABLE
BY EACH RESPECTIVE USER. CARE SHOULD THEREFORE
BE EXERCISED TO ENSURE THAT ANY NEW USERSARE
FAMILIAR WITH THIS REQUIREMENT.
AUX PERSONNESAYANT DES PROBLEMES D’AUDITION.
IL POSSEDE UN ECOUTEUR A VOLUME VARIABLE. A
LA PREMIERE UTILISATION, ASSUREZ VOUS QUE LE
BOUTON DE REGLAGE DU VOLUME SOIT POSITIONNE
SUR LA POSITION VOLUME MINIMUM. LES PERSONNES
MALENTENDANTES POURRONT PAR LA SUITE
AUGMENTER LE VOLUME POUR L’ADAPTER A LEUR
AUDITION.
Download from Www.Somanuals.com. All Manuals Search And Download.
CALLER IDENTIFICATION
- Caller ID features
- Dial Caller ID numbers
- Store numbers and names into the phone book
- Delete stored names and numbers
21
21
21
22
ADDITIONAL HANDSETS
- General settings
- Using several handsets
- Deregister all additional handsets from the base
- Internal calls
- Call transfer to another registered handset
- Headset option
23
23
24
24
25
25
ADDITIONAL BASE UNIT
- General settings
- How to add a base unit
26
26
TROUBLE SHOOTING
- Generality
- A warning tone is heard during a call
- The phone does not work
27
27
27
27
- No number is displayed when the phone rings
GUARANTEE
28
For product support and help visit our website at
telephone 01707 384438
or fax 01707 372529
Download from Www.Somanuals.com. All Manuals Search And Download.
3
SOMMAIRE
F
PAGE
DESCRIPTION
- Description du combiné et de la base
6
INSTALLATION
- Raccordements du téléphone et mise en place des batteries
- Chargement des batteries
- Rayon d’action
30
30
31
31
- Entretien du téléphone
REGLAGE DE LA BASE
- Réglage du volume de sonnerie de la base
REGLAGE DU COMBINE
32
- Présentation des icônes
33
33
34
35
35
- Volume, mélodie de la sonnerie et vibreur
- Enregistrement d’un combiné sur la base
- Annuler l’enregistrement d’un combiné de la base
- Propiétés du réseau, touche R (Flash) , insertion d’une Pause
UTILISATION DU TELEPHONE
- Appeler
- Répondre à un appel
- Rappeler le dernier numéro composé (BIS)
- Réglage du volume et de la tonalité de l’écouteur
- Recherche du combiné (pagination)
- Minuterie (durée des appels)
37
37
37
37
39
39
REPERTOIRE
- A propos du répertoire
- Réglage de la sonnerie du combiné
- Répertoire
- Enregistrement d’un numéro et d’un nom
- Appeler en utilisant le répertoire
- Modifier un numéro du répertoire
- Effacer un numéro du répertoire
40
40
40
41
42
42
42
Download from Www.Somanuals.com. All Manuals Search And Download.
4
AFFICHAGE DU NUMERO DE L’APPELANT
- Affichage des numéros d’appels
43
43
44
44
- Sélectionner et appeler un numéro
- Transfert de numéros dans le répertoire
- Effacer un ou plusieurs numéros enregistrés
COMBINES ADDITIONNELS
- Généralités
45
45
46
46
47
47
- Utilisation de plusieurs combinés
- Annuler l’enregistrement de tous les combinés de la base
- Communications internes
- Transfert d’appel vers un autre combiné enregistré
- Option casque
BASE ADDITIONNELLE
- Généralités
- Ajouter une base supplémentaire
48
48
PROBLEMES DIVERS
- Généralités
49
49
49
49
- Emission d’un signal d’alarme pendant la conversation
- Le téléphone ne fonctionne pas
- Aucun numéro ne s’affiche lorsque le téléphone sonne
GARANTIE
50
TEL. SERVICE APRES VENTE :
03 28 58 75 99
Pour tout renseignement technique ou toute
commande visitez notre site web sur
Parc d’Activités du Basroch
2, rue Galilée
59760 Grande Synthe
Download from Www.Somanuals.com. All Manuals Search And Download.
5
DESCRIPTION
HANDSET DESCRIPTION
DESCRIPTION DU COMBINE
Speaker
Ecouteur
LCD display
Afficheur LCD
Pick up and hang up key
Touche de décroché et de
raccroché
Function and
phonebook keys
Touches de fonction et
de répertoire
Amplifier switch
Interrupteur ampli
Tone adjustment
Réglage de la
tonalité
Shaker switch
Interrupteur vibreur
Keypad
Clavier
Amplifier key
Touche ampli
Microphone
Flash Key
Touche flash
Download from Www.Somanuals.com. All Manuals Search And Download.
6
DESCRIPTION
HANDSET DESCRIPTION
DESCRIPTION DU COMBINE
Belt clip
Clip ceinture
Amplifier volume
button adjustment
Bouton de réglage
volume ampli
Batteries cover
Couvercle de batteries
Download from Www.Somanuals.com. All Manuals Search And Download.
7
DESCRIPTION
BASE CONTROLS
CONTROLES SUR LA BASE
Handset cradle
Support combiné
Charge contacts
Contacts de charge
Page key
Touche de pagination
Download from Www.Somanuals.com. All Manuals Search And Download.
8
DESCRIPTION
BASE CONNECTIONS
CONNECTIONS SUR LA BASE
Ringer volume setting switch
Interrupteur de réglage sonnerie
* Power adaptor socket
* Connecteur adaptateur
secteur
** Line socket
** Connecteur cordon de ligne
(*) Classified “hazardous voltage” according to EN60950 standard.
Classé “tension dangereuse” selon la norme EN60950.
(**) Classified TNV-3 according to EN60950 standard.
Classée TNT-3 selon la norme EN60950
Download from Www.Somanuals.com. All Manuals Search And Download.
9
GENERAL SETTINGS
1 - HOW TO CONNECT THE PHONE AND SET THE BATTERIES
1 - Plug the adaptor in the power wall socket and the power plug in the
base socket (*).
2 - Connect the line cord plug to the base socket (**).
3 - Connect the line cord to the PTT socket.
4 - Insert the batteries with the correct polarity into the batteries compartment
and replace the battery cover.
5 - Place the handset on the base unit then a short beep will be heard
and the battery symbol will flash on the display, except if the batteries are
totally empty.
NOTE: Do not expose the base to electric equipment like TV, radio, monitors,
sunlight, heat or other phones...to avoid any disturbances of your phone.
(*) Classified “hazardous voltage” according to EN60950 standard.
(**) Classified TNV-3 according to EN60950 standard.
2 - CHARGING THE BATTERIES
The phone is supplied with NiMH rechargeable batteries. In standby mode, batteries
are fully charged around 170 hours and talk time is around 8 hours. The battery
charge icon
will flash as long as the phone is being charged and will stop when
the charging process is complete. The phone has an automatic charging control to
avoid excessive charging.
IMPORTANT: Batteries must be charged during 24 hours before using the
phone for the first time.
Battery charge icon:
The handset display shows
when the batteries are flat and when a warning
signal is heard. If the phone does not have enough power or is not completly
recharged, it switches itself off automatically until it is returned to the base unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
GENERAL SETTINGS
3 - PHONE RANGE
The phone radio range can work up to 300 m and radio signal can be affected by
many factors like a wall, obstacles...The maximum range if there are no obstacles
between the phone and the base unit is around 300 m.
If the range is restricted by walls in a house or in the office, the base unit should be
in a slightly elevated position.
A warning signal (beep) will be heard when the handset is out of the range, the call
will be stopped if the handset does not come nearer to the base unit.
4 - CLEAN THE PHONE
Clean the phone with a soft cloth. Keep the base and handset charging contacts
clean. Never use polishes or cleaning agents - they could damage the finish or the
electrics inside.
Note: We advise you to place the telephone on a table cloth or similar, as rubber feet
can mark some surfaces.
Thunderstorms: unplug your phone from the telephone socket during
thunderstorms because it could damage your phone. Your guarantee does not
cover thunderstorm damage.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
BASE SETTINGS
BASE RINGER VOLUME
The base ringer volume can be adjusted by using the slider switch located on the
base rear panel.
Remark: It is only possible to adjust the ring volume, the ring tone melody cannot
be adjusted.
The following settings are available:
Switch position Symbol
Function
Off
Min
Med
Max
Pos 1
Pos 2
Pos 3
Pos 4
For product support and help visit our website at
telephone 01707 384438
or fax 01707 372529
Download from Www.Somanuals.com. All Manuals Search And Download.
12
HANDSET SETTINGS
1 - GENERAL SETTINGS ICONS DIPSPLAYED
There are three settings icons displayed on the handset:
Ringer volume icon
to set the ring volume and melody.
to register / deregister handsets.
Register handsets icon
Network settings, Flash time and Dial Pause icon settings
to set Network,
Flash time and Pause. The whole menu is controlled by using the following keys:
- To activate or deactivate the menu and programing mode use the
key.
- To move forward in the menu press the
backward.
(
) and
(
) keys to move
- To move forward to another step or confirm a selection press the
2 - HANDSET RINGER VOLUME, MELODY AND SHAKER
To set the volume and melody please follow instructions below:
key.
1 - Press the
2 - Press the
key.
) or the
(
(
) key to select the desired icon shown
on the display. The selected icon will flash on the display.
3 - Press the key to select the icon.
4 - Now you can select one of the possibilities below:
1/4 ++++ for the Ringer volume.
2/4 for the Normal calls ringer melody.
3/4 for the Phone book
4/4 for the Phone book
ringer melody.
ringer melody.
Press the
) and
5 - Press the
to scroll through the menu. If you want to modify entries press
(
(
) keys.
key to confirm the settings and exit to the menu.
6 - If you want to exit to the menu press
.
7- In addition to the ring, you can use the shaker function with the switch
set to the
position.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
HANDSET SETTINGS
IMPORTANT: If you connect several bases together, the handsets registered
to the additional bases will ring for a few seconds during an incoming call
even if you take the line with one of the first base handsets.
3 - HANDSET REGISTRATION
How to register a handset to a base unit:
1 - Unplug the mains adaptor from the base unit during few seconds.
2 - Replace the adaptor to the power socket.
3 - Press the
key.
4 - Press the
(
)orthe
(
) key to select the
icon shown on the
key; 1/1 0000
display. The selected icon will flash on the display, then press
will be displayed.
5 - Enter the base unit PIN code (factory setting to 1111), then press
key.
6 - The handset is now searching for the base unit to be registered, a beep will be
heard when the handset is registered to the base.
Note: the handset supplied with the base unit is already registered to the base unit.
So it is not necessary to register this handset.
4 - HANDSET DEREGISTRATION
To deregister the current handset from the base unit follow the instructions
below:
1 - Press the
2 - Press the
key.
and the
keys to enter
number, 1/1 0000 will be displayed.
key.
3 - Enter the base unit PIN code (factory setting to 1111), then press
The handset is deregistered from the base unit and a beep will be heard when the
handset is registered to the base. If you wish to use several handsets and base units,
all handsets must be registered. Each handset you want to use must be registered
separately to the base unit. You can register up to 2 base units for one handset and
up to 4 handsets can be registered to one base unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
HANDSET SETTINGS
5 - NETWORK FEATURES, FLASH TIME, DIAL PAUSE
1 - Press the
2 - Press the
key.
) or the
(
(
) key to select the desired icon shown
on the display. The selected icon will flash on the display.
3 - Press the key to select the icon.
4 - You can choose from the menu below:
1/5 1/2 : 1 For UK, 2 for France (CID features).
2/5 Tone/Pulse for dialling must be set to Tone.
3/5 A,B,C,D (Telephone network settings)
4/5 Flash time R key
5/5 Dial pause to insert a pause in the mumber
You can scroll into the menu by pressing the
key. Press the
(
) or
the
(
) key to modify entries, press
key to exit the menu.
to confirm modification.
5 - Press the
Network settings
You can choose between 4 network settings:
A Factory setting (default value), B, C, D
These settings are used to match the signal level when working on different
phone networks.
Note: The setting should be left to A
Flash time settings for
. You can choose between 2 settings:
a) ***
b) ******
100 ms for United Kingdom
300 ms for France
Dial pause settings
You can insert a pause time in a phone number after the first digit, the digits after
the pause time are dialled after a 3 seconds delay. Two settings are available to
use this feature Yes or No.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
USING THE PHONE
1 - MAKING A CALL
1 - Dial the phone number you want to call, you can press the
an incorrect entry.
key to cancel
2 - Press the
, the number is automatically dialled.
3 - On completion of the call simply press the
the handset on the base.
again to release the line or put
2 - ANSWERING A CALL
When an incoming call is received proceed by:
1 - Press the
key to take the line and speak.
2 - On completion of the call simply press the
the handset on the base.
again to release the line or put
3 - USE THE CALL BACK FEATURES
The five last dialled call numbers will be shown on the display when pressing the
key.
1 - Press the
key and scroll through the list by pressing the
(
) or
(
) keys until you select the number you want.
key to dial the number.
2 - Press the
Note: Pressing the
key again will cancel this process. The displayed entry
key, a short beep will be heard to confirm.
can be deleted by pressing the
4 - HOW TO USE THE VOLUME AND TONE FUNCTIONS
Setting the handset volume, treble and bass:
The handset hearing volume can be set during a call by using the volume key
located on the handset rear side. Pressing the volume key increases the handset
volume by 4 steps of 4 dB each time. The phone amplification can be increased
with the V slider switch and the
key.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
USING THE PHONE
The following settings are available:
1 - The V switch set to and activated (key is lighting).
The handset volume can be adjusted within the following values range :
4 dB/ 8 dB/ 12 dB/ 16 dB.
2 - The V switch set to
and
activated (key is lighting).
The handset volume can be adjusted within the following values range:
16 dB/ 20 dB/ 24 dB/ 28 dB.
In addition for both settings, you can use the tone control
to increase treble and bass up to 10 dB.
slider switch
Notes:
- Pressing the
key deactivates the additional amplification and the tone
control functions (Key is not lighting).
- You can leave the V slider switch to
impaired hearing user.
position if the phone is always used by
5 - PAGING THE HANDSET
If you wish to locate your handset simply follow the instructions below:
1 - Press the
key on the base unit located on the base front side.
2 - All registered handsets will be paged and will ring.
3 - Press twice the
Pressing the
on the located handset to stop the paging mode.
key on the base unit has the same effect.
6- TIMER
A timer will be displayed on the screen after starting the call. You can check the
call length by using this function.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
PHONE BOOK
1 - ABOUT THE PHONE BOOK
Names and phone numbers can be stored in the phone book. Each phone number
stored in the phone book can be called by pressing only few buttons. If your Caller ID
service is available, the name and the number of the caller will be displayed during
the incoming call. This will be done only if the caller name and number have been
stored in the phone book.
The phone book is divided into two parts (2 x 10 entries). One phone book can be
used for friends and family numbers and the second one for business contacts. The
entries in both phone books are sorted out by using an alphabetic list. Each name
can contain up to 10 characters and each phone number can have up to 25 digits.
2 - PHONE BOOK HANDSET RING TONE SETTINGS
It is possible to have a different ring to identify which phone book is being used.
You can set it as below:
1 - Normal phone call
2 - Calls from phone numbers and names in the first phone book
3 - Calls from phone numbers and names in the second phone book
.
.
Differentiated ring tones are only available when the caller ID is activated.
IMPORTANT :
Even if a caller is stored in a phone book, it can happen that only the normal ring
tone is triggered, in this case caller may have used his or her private number function.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
PHONE BOOK
3 - STORING A NUMBER WITH A NAME
Follow instructions below to store new entries in the phone book:
1 - Enter the phone number and dialling codes you wish to set in the phone book.
2 - Select one of the two phone books by pressing the
or
key, a beep
will be heard and the phone book icon selected will flash.
3 - Enter the corresponding name and number by pressing the corresponding
number key once or twice to select the desired letter (see the table below).
Key
Characters
1
[space] - 1
2
AB C 2
3
DE F 3
4
G HI4
5
J KL5
6
MNO 6
7
P QRS 7
8
TUV8
9
WXYZ9
0
0
* or #
To confirm the key and go to another one
Example: for AB press A*B
4 - Press the
key to store the entry then a beep will be heard to confirm.
Note: To cancel the process only press and hold the
key.
4 - DIALLING USING THE PHONE BOOK
1 - Select the desired phone book by pressing the
2 - Select the desired entry in the list by using the
or
.
(
)or
(
) key .
key.
3 - Press the
key then the number will be automatically dialled.
or
Note: The process can be cancelled by pressing the
Download from Www.Somanuals.com. All Manuals Search And Download.
19
PHONE BOOK
5 - MODIFY A PHONE BOOK ENTRY
1 - Select the desired phone book by pressing the
or
(
key.
2 - Select the desired number to modify by pressing the
keys.
) or
(
)
3 - Press the
key.
4 - The number will be displayed and can be deleted by pressing the
key.
5 - Enter the new number and press the
key to store.
6 - DELETE A PHONE BOOK ENTRY
1 - Select the desired phone book by pressing the
or
(
key.
2 - Select the desired number to delete by pressing the
keys.
) or
(
)
3 - Press the
key.
4 - Press the
key to delete the entry.
5 - Display will show OK?
5 - Press the to confirm then a beep will be heard.
For product support and help visit our website at
telephone 01707 384438
or fax 01707 372529
Download from Www.Somanuals.com. All Manuals Search And Download.
20
CALLER IDENTIFICATION
1 - CALLER ID FEATURES
IMPORTANT: You need to subscribe to a Caller ID service from your local phone
company if you wish to use this feature.
Caller ID will show the caller name and phone number on the handset display. If the
phone number is stored in the phone book, the corresponding name will be displayed
with the correct ring tone (phone book ring tone).
The display shows ****** for private call (caller does not want to show his or her
name and number).
The 10 last incoming calls are automatically stored in Caller ID list.
When the memory is full, the oldest call will be replaced by the last one.
Note: The
symbol will be displayed if you receive a call in your absence.
2 - DIAL CID NUMBERS
1 - Press the
2 - Select the desired number to dial by pressing the
Two short beeps will be heard if you reach the end of the list.
3 - Press the key to dial the number or press the
time and the date of the call or press the key to exit the menu.
key.
(
)or
(
) key.
to display the
3 - STORE NUMBERS AND NAMES INTO THE PHONE BOOK
1 - Press the
2 - Select the desired number to store in the phone book by pressing the
or ) keys. Two short beeps will be heard if you reach the end of the list.
3 - Select the desired phone book in which you want to store the number by pressing
the or key.
4 - Store the name as described in “PHONEBOOK” item.
5 - Press the to confirm the storage in the phone book.
key.
(
)
(
Download from Www.Somanuals.com. All Manuals Search And Download.
21
CALLER IDENTIFICATION
4 - DELETE STORED NAMES AND NUMBERS
1 - Press the
2 - Select the desired number to delete by pressing the
key. Two short beeps will be heard when you reach the end of the list.
3 - Press the key to delete the entry, a short beep will be heard to confirm.
key.
(
) or
(
)
For product support and help visit our website at
telephone 01707 384438
or fax 01707 372529
Download from Www.Somanuals.com. All Manuals Search And Download.
22
ADDITIONAL HANDSETS
1 - GENERAL SETTINGS
With the DECT standard you have the possible settings below:
- Register up to 4 handsets to one base unit.
- Register up to 2 base units to each handset.
- Make internal call handset to handset and transfer call between handsets
registered to the same base unit.
- You can increase the phone range by using 2 base units (move between the
phone coverage areas).
2 - USING SEVERAL HANDSETS
For practical applications and to make life easier, you can register several handsets
to the same base unit. You will be able to answer a call anywhere in the office or the
home at any time because all handsets will ring at the same time. You can call
another place in the office or home by calling another registered handset.
You can transfer an incoming call to another handset.
Note: only one incoming or internal call can be made at the same time.
How to use several handsets:
All handsets you wish to use in the base unit must be registered to this base unit.
To add another handset please follow instructions below for each handset:
1 - Unplug the mains adaptor from the base unit during few seconds.
2 - Replace the adaptor to the power socket.
3 - Press the
key.
4 - Press the
(
)orthe
(
) key to select the
icon shown on the
key.
display. The selected icon will flash on the display, then press
5 - Enter the base unit PIN code (factory setting to 1111), then press
6 - The handset is now searching for the base unit to be registered.
key.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
ADDITIONAL HANDSETS
Note: to get the maximum efficiency and maximum range you must put the handset
near the base unit. The handset range will be the same for each handset.
3 - DEREGISTER ALL ADDITIONAL HANDSETS FROM THE BASE
To deregister all handsets from the base unit follow the instructions below:
1 - Take one handset.
2 - Press the
3 - Press the
key.
and the
keys to enter
number 1/1 0000 will be dispalyed.
4 - Enter the base unit PIN code (factory setting to 1111), then press
key.
All additional handsets are deregistered from the base unit.
Note: handset used to deregister the additional handsets is not deregistered.
4 - INTERNAL CALLS
When you are using several handsets registered to the same base unit, you can
make internal calls handset to handset. To make a call handset to handset please
follow instructions below:
1 - Press the
key.
2 - All other handsets will ring.
3 - Press the
key to answer the call.
A tone signal will be heard during a call when you receive an external call. To
answer the external call you must finish your internal call first.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
ADDITIONAL HANDSETS
5 - CALL TRANSFER TO ANOTHER REGISTERED HANDSET
External calls can be transfered to another registered handset from the answering
handset (both handsets must be registered to the same base unit).
During an incoming call:
1 - Press the
1 - Press the
key to answer the call.
key to transfer the call.
2 - All others handsets will ring.
3 - Press the
key on the requested handsets to answer the call.
If you do not wish to come back to your call and do not wish to transfer the call to
other handsets simply press the
key on your called handset.
Note : You cannot transfer an external call to a handset which is not registered to
the same base station.
6 - HEADSET OPTION
If you wish you can connect a headset ref: HEADCL_BLK to the headset socket
located on the side of your phone, with this headset you can use all phone functions
as described before. To answer a call simply press the
press a second time to release the line.
to take the line and
For product support and help visit our website at
telephone 01707 384438
or fax 01707 372529
Download from Www.Somanuals.com. All Manuals Search And Download.
25
ADDITIONAL BASE UNIT
1 - GENERAL SETTINGS
Several base units can be connected to the network in order to extend the range of
the handsets. When several base units are registered to a handset, it can
automatically search for the next base unit if you go outside the range of the first
base unit. The transfer between base units is handled automatically, although this
cannot be done whilst a call is in progress. Handset will keep its connection with
one of the base units until it loses connection due to having moved out of range. In
this case, the handset searches for a new base unit in its registration list.
The base units coverage areas must overlap to ensure there are no gaps in the
coverage. Otherwise the radio connection will be lost.
2 - HOW TO ADD A BASE UNIT
1 - Connect the additional base on the network phone socket.
2 - Plug in the adaptor.
3 - Register the handset to the base unit as described before.
Remark: The first registered handset has priority on the first base. It will be activated
when the handset will move to the second base (move to the new radio range).
To check if your handset or all handsets registered to this base are registered
simply press the page button
on the new base, all new handsets registered
to this base will ring.
IMPORTANT: If you connect several bases together, the handsets registered
to the additional bases will ring for a few seconds during an incoming call
even if you take the line with one of the first base handsets.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
TROUBLE SHOOTING
IF THE PHONE DOES NOT WORK
Generality:
Make sure that the phone line cord and adaptor are correctly plugged in and are not
damaged.
Make sure that the batteries are fully charged.
Connect another phone on your phone socket or move your phone to another socket
to check if the failure is coming from your phone or your PTT socket.
A warning tone is heard during a call:
The batteries are empty and the handset needs to be replaced in the base unit
.
The phone does not work:
Make sure that the line cord and the power adaptor are correctly connected to the
base unit or to the PTT plug and wall power socket.
No number is displayed when the phone rings:
- Please contact your phone network provider to get the caller identification service.
- When the caller does not want to show his or her number (private number), the
display will show ******. However, it could be a call from a PBX and caller ID may not
work properly if the phone is connected to a PBX.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
GUARANTEE
GUARANTEE
From the moment your Geemarc product is purchased, Geemarc
guarantee the product for one year. During this time, all repairs or
replacements (at our option) are free of charge. Should you
experience a problem then contact our helpline or visit our website
negligence or breakages to any parts. The product must not be
tampered with or taken apart by anyone who is not an authorised
Geemarc representative. The Geemarc guarantee in no way limits
your legal rights.
IMPORTANT: YOUR RECEIPT IS PART OF YOUR GUARANTEE
AND MUST BE RETAINED AND PRODUCED IN THE EVENT
OFAWARRANTY CLAIM
Please note: The guarantee applies to the United Kingdom only.
DECLARATION: Geemarc Telecom SAhereby declares that this
product is in compliance with the essential requirements and other
relevant provisions of the Radio and Telecommunications Termi-
nal Equipment Directive 1999/5/EEC and in particular article 3 sec-
tion 1a, 1b and section 3. The telephone does not operate if the
line current is lower than 18 mA.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
GUARANTEE
Electrical connection : The apparatus is designed to operate
from a 230V 50Hz supply only. (Classified as «hazardous voltage»
according to EN60950 standard).
The apparatus does not incorporate an integral power on/off switch.
To disconnect the power, either switch off supply at the mains power
socket or unplug the AC adaptor. When installing the apparatus,
ensure that the mains power socket is readily accessible.
Telephone connection : Voltages present on the
telecommunication network are classified TNV-3
(Telecommunication Network Voltage) according to the EN60950
standard.
For product support and help visit our website at
telephone 01707 384438
or fax 01707 372529
Download from Www.Somanuals.com. All Manuals Search And Download.
29
|