your Gateway Powerline Adapter
user'sguide
PLU-300 & PLE-310
Installing
Configuring
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1
Setting Up Your Powerline Adapter. . . . . . . . . . . . . . . . 1
Installing the Powerline adapter driver . . . . . . . . . . . 2
About network configurations . . . . . . . . . . . . . . . . . . 8
Setting up a DHCP IP address for each computer . 21
Turning the powerline adapter off . . . . . . . . . . . . . . . . . . 26
Sharing Your Network Resources . . . . . . . . . . . . . . . . 29
Turning on Windows file and printer sharing . . . . . 38
Sharing drives or folders . . . . . . . . . . . . . . . . . . . . 40
Un-sharing drives, folders, and files . . . . . . . . . . . . 42
Sharing printers . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Using the network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Viewing shared drives and folders . . . . . . . . . . . . . 43
Mapping a Network Drive . . . . . . . . . . . . . . . . . . . . 44
Opening files across the network . . . . . . . . . . . . . . 45
Copying files across the network . . . . . . . . . . . . . . 45
Printing files across the network . . . . . . . . . . . . . . 46
Using the Powerline Adapter Configuration Utility . . 47
About the Powerline configuration utility . . . . . . . . . . . . 48
Using the Device tab settings . . . . . . . . . . . . . . . . . 49
Using the Network tab settings . . . . . . . . . . . . . . . 51
Using the Security tab settings . . . . . . . . . . . . . . . . 52
Using the Advanced tab settings . . . . . . . . . . . . . . 54
Getting Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Automated troubleshooting system . . . . . . . . . . . . 58
2
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
i
Telephone numbers . . . . . . . . . . . . . . . . . . . . . . . . 58
A
Safety, Regulatory, and Legal Information . . . . . . . . . 59
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
Setting Up Your
Powerline
Adapter
Powerline adapters let you create a
network using the existing electrical
wiring in your home or office instead of
installing Ethernet cables.
This chapter describes how to connect a
Gateway USB to Powerline adapter or a
Gateway Ethernet to Powerline adapter
to your Windows computer and
configure Windows for a powerline
network. Complete these tasks in
sequence:
■
■
■
“Step 1: Installing the hardware
and software” on page 2.
“Step 2: Adding the computer
to the network” on page 8.
“Step 3: Configuring the TCP/IP
protocol” on page 20.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Chapter 1: Setting Up Your Powerline Adapter
Step 1: Installing the hardware and
software
Installing the Powerline adapter driver
Use the following instructions to:
■
■
■
Install the Powerline software on the computer that
you want to use to manage the Powerline network
Connect the Powerline network adapter to an AC
outlet
Connect the Powerline network adapter to your
computer.
Before installing the Powerline device, make sure
that there are no other network encryption
Important
management utilities installed on your computer. If
other utilities are installed, uninstall them before
installing the Powerline adapter and software.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Step 1: Installing the hardware and software
To install the Powerline adapter software and
hardware
1
Insert the Gateway Powerline Adapter CD in the
computer’s CD or DVD drive. The installation
program starts.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Chapter 1: Setting Up Your Powerline Adapter
Click Install the software. The InstallShield Wizard
2
starts.
- OR -
If you are installing the Gateway PLU-300 Ethernet
adapter and the wizard does not start automatically,
click Start, Run, type d:\plu-300\setup.exe in the Run
box, then click OK. The InstallShield Wizard starts.
- OR -
If you are installing the Gateway PLE-310 Ethernet
adapter and the wizard does not start automatically,
click Start, Run, type d:\ple-310\setup.exe in the Run
box, then click OK. The InstallShield Wizard starts.
3
Click Next, then follow the on-screen instructions.
During the installation:
■
If installing the software on Windows XP and a
message tells you that the driver has not passed
Windows Logo testing, click Continue Anyway. The
device driver files are copied to the hard drive.
■
If installing the software on Windows 2000 and a
a message tells you that no digital signature is
found, click Yes. The device driver files are copied
to the hard drive.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Step 1: Installing the hardware and software
4
When prompted to plug-in the Powerline adapter:
■
Plug the adapter into a AC power outlet
For the best network performance, we suggest
plugging the adapter directly into an AC outlet and
not into a surge protector. The adapter has a
built-in surge protector.
Important
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Chapter 1: Setting Up Your Powerline Adapter
Plug the USB or RJ-45 cable into the Powerline
■
adapter
■
Plug the other end of the RJ-45 or USB cable into
the computer
5
Continue following the on-screen instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Step 1: Installing the hardware and software
Click Finish to complete the installation.
6
7
If a message asks you whether you want to restart your
computer, click Yes to restart your computer now or
click No to restart your computer later.
8
After restarting the computer, the Gateway Power
configuration utility icon appears on the computer
desktop. For more information about using the utility,
see “Using the Powerline Adapter Configuration
Utility” on page 47.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Chapter 1: Setting Up Your Powerline Adapter
Step 2: Adding the computer to the
network
About network configurations
After the Powerline software and hardware is installed, the next
step is to determine how the computer with the powerline
adapter will be added to network. There are a number of
possible network configurations. The two common network
configurations used with a Powerline network are:
■
Dynamic Host Control Protocol (DHCP) with a router - A
DHCP network configuration uses a router to
automatically assign IP addresses to each computer or
network device. The network is made up of:
■
A router to connect the local area network (LAN)
with the wide area network (WAN or broadband
network).
■
■
■
A cable or DSL modem to provide access to the
Internet
Your computers that are connected to form a
network of computers
Powerline (electric cables) and Ethernet or USB
cables connecting each of these components.
Cable/DSL
modem
Router
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Step 2: Adding the computer to the network
■
Internet Connection Sharing (ICS) - An ICS network
configuration uses a host computer that assigns
Internet Protocol (IP) addresses to each computer or
network device and directs network communication
between computers on the local area network (LAN)
and the Internet. The network is made up of:
■
A host computer that has an Internet connection
(one for the Internet and one for the LAN). The
Internet connection can be a dial-up connection,
cable modem, DSL, or other broadband Ethernet
connection. The LAN connection can be wired
(for example Powerline or Ethernet), wireless, or a
USB Ethernet connection.
■
■
Other client computers
Dial-up, cable, or DSL modem to provide access to
the Internet
■
Powerline (electric cables) and Ethernet cables
connecting each of these components.
Dial-up/
Cable/DSL
modem
Host
computer
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Chapter 1: Setting Up Your Powerline Adapter
Naming the computers and the
workgroup
Each computer on the network must have a unique name and
be identified as part of a workgroup. Naming each computer
must be done individually on each computer.
If you have an existing network make sure that you give the
new computers you are adding to the network the same
workgroup name.
The Windows XP Network Setup Wizard steps you through the
process of naming each computer, setting the network
workgroup name, and other network settings. To name your
computers and workgroup in Windows XP, go to “Naming the
computers and the workgroup in Windows XP” on page 10.
To name your computers and workgroup in Windows 2000, go
to “Naming the computers and the workgroup in
Windows 2000” on page 17.
To name your computers and workgroup in Windows 98SE or
Windows Me, see “Naming the computers and the workgroup
in Windows 98SE or Windows Me” on page 18.
Naming the computers and the workgroup in
Windows XP
Use the Windows XP Network Setup Wizard to name each
computer and workgroup as well as select other network
settings in Windows XP.
The following example screens show the screens
Important
that typically appear in the course of using the
wizard. If your network situation differs from that
used in this example, you may encounter
additional screens or screens with different
selections. Make sure that you read each screen in
the wizard and make your selections based on
your particular network situation.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Step 2: Adding the computer to the network
To run the Windows XP Network Setup Wizard:
1
Click Start, All Programs, Accessories, Communications,
then click Network Setup Wizard. The Network Setup
Wizard opens.
- OR -
Click the Network Setup Wizard icon
on the
Windows XP taskbar. The Network Setup Wizard
opens.
2
Click Next to continue through the wizard.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Chapter 1: Setting Up Your Powerline Adapter
Click Next. If the The wizard found disconnected network
3
hardware screen opens, make sure that one end of the
Ethernet or USB cable is connected to your computer
and the other end is connected to a Gateway
powerline adapter. Also, make sure that a router or
computer is connected to your network and turned
on.
The wizard found disconnected network hardware
Important
screen will open if your computer also has wireless
Ethernet networking built-in. If your computer has
wireless Ethernet networking built-in, click Ignore
disconnected network hardware, then click
Next.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Step 2: Adding the computer to the network
4
Click Next. The Select a connection method screen opens.
5
6
Click This computer connects to the Internet through another
computer on my network or through a residential gateway,
then click Next.
If the Your computer has multiple connections screen
opens, click Let me choose the connections to my network,
then click Next.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Chapter 1: Setting Up Your Powerline Adapter
7
On the Select the connections to bridge screen, click to
select the Local Area Connection check box.
8
Click Next. The Give this computer a description and
name screen opens.
9
Type a description of the computer in the Computer
description box.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Step 2: Adding the computer to the network
10 Type a unique computer name in the Computer name
box. This name identifies the computer to other users
on the network. Use a computer name of up to 15
characters with no blank spaces. Each computer name
must be unique on your network. All-numeric
computer names are not allowed. Names must
contain some letters.
You must give each computer on the network a
unique Computer Name and the same Workgroup
Name.
Important
11 Click Next. The Name your network screen opens.
12 Type a name for your workgroup in the Workgroup
name box. Use a workgroup name of up to 15
characters with no blank spaces. The workgroup name
must be the same for all computers in your network
workgroup, and the name must be different than any
computer name on your network.
13 Click Next. The Ready to apply network settings screen
opens.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Chapter 1: Setting Up Your Powerline Adapter
14 Click Next to apply the network settings. The You’re
almost done screen opens.
15 If you are setting up networking on other computers,
you may want to use the Network Setup Wizard to do
so. Click a method for installing and configuring the
network on your other computers or click Just finish
the wizard; I don’t need to run the wizard on other computers.
16 Click Next.
17 Click Finish. After you name each computer and assign
it to your workgroup, go to “Turning the powerline
adapter off” on page 26.
For more information about using the Network
Setup Wizard in Windows XP, click Start, then
click Help and Support.
Help and
Support
Type the keyword Network Setup Wizard in the
Search box
, then click
the arrow.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Step 2: Adding the computer to the network
Naming the computers and the workgroup in
Windows 2000
To identify a Windows 2000 computer on the network:
1
Click Start, Settings, then click Control Panel. The
Control Panel window opens.
2
Double-click the System icon. The System Identification
dialog box opens.
3
4
Click the Network Identification tab.
Click Properties. The Identification Changes dialog box
opens.
5
Type a unique computer name in the Computer name
box. This name identifies the computer to other users
on the network. Use a computer name of up to 15
characters with no blank spaces. Each computer name
must be unique on your network. All-numeric
computer names are not allowed. Names must
contain some letters.
You must give each computer on the network a
unique Computer Name and the same Workgroup
Name.
Important
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Chapter 1: Setting Up Your Powerline Adapter
6
Type a name for your workgroup in the Workgroup box.
Use a workgroup name of up to 15 characters with no
blank spaces. The workgroup name must be the same
for all computers in your network workgroup, and the
name must be different than any computer name on
your network.
7
8
9
Click OK to close the Identification Changes dialog box.
Click OK to close the System Identification dialog box.
After you name each computer and assign it to your
workgroup, go to “Step 3: Configuring the TCP/IP
protocol” on page 20.
Naming the computers and the workgroup in
Windows 98SE or Windows Me
To identify a Windows 98SE or Windows Me
computer on the network:
1
2
3
Click Start, Settings, then click Control Panel. The
Control Panel window opens.
If you are using Windows Me, click view all Control Panel
options.
Double-click the Network icon. The Network dialog box
opens.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Step 2: Adding the computer to the network
Click the Identification tab.
4
5
Type a unique computer name in the Computer name
box. This name identifies the computer to other users
on the network. Use a computer name of up to 15
characters with no blank spaces. Each computer name
must be unique on your network. All-numeric
computer names are not allowed. Names must
contain some letters.
You must give each computer on the network a
unique Computer Name and the same Workgroup
Important
Name.
6
Type a name for your workgroup in the Workgroup box.
Use a workgroup name of up to 15 characters with no
blank spaces. The workgroup name must be the same
for all computers in your network workgroup, and the
name must be different than any computer name on
your network.
7
8
Click OK to close the Network dialog box.
Click X to close the Control Panel.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Chapter 1: Setting Up Your Powerline Adapter
After you name each computer and assign it to your
9
workgroup, go to “Step 3: Configuring the TCP/IP
protocol” on page 20.
Step 3: Configuring the TCP/IP protocol
other. One of several available protocols must be set up on each
computer you plan to use on your network. We recommend
you use the Transmission Control Protocol/Internet Protocol
(TCP/IP), which is widely accepted and compatible for local
area networks (LANs), as well as for Internet communications.
Terms you should know
DHCP - Dynamic Host Configuration Protocol
Important
(DHCP) lets a router automatically assign an IP
address to a computer on the network.
IP Address - Internet Protocol (IP) address is a
number that uniquely identifies a computer on the
network.
When networking is set up in Windows XP, TCP/IP is
automatically installed as the default protocol. When you run
the Windows XP Network Setup Wizard as described in
“Naming the computers and the workgroup in Windows XP”
on page 10, TCP/IP was configured for you.
To set up TCP/IP for Windows 2000, go to “Setting up a DHCP
IP address for Windows 2000” on page 22.
To set up TCP/IP for Windows 98SE or Windows Me, go
to“Setting up a DHCP IP address for Windows 98SE or
Windows Me” on page 24.
The following section shows you how to configure
Important
your computer for a DHCP IP address. If your
networking situation requires a static IP address,
see Windows Help for more information.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Step 3: Configuring the TCP/IP protocol
Setting up a DHCP IP address for each
computer
In order to communicate with computers on the network and
on the Internet, you must either set the protocol to Obtain an IP
address from a DHCP server or make the IP address settings
manually. If you use a router that can act as the DHCP server,
you can select Obtain an IP address from a DHCP server. Obtaining
an IP address automatically using DHCP is one of the most
common methods for setting up network devices.
If your network configuration requires a static IP address (one
that does not change), you must set the IP address manually.
This means that you need to enter an IP address and a subnet
mask.
If you are connecting to a home Ethernet network, have a cable
or DSL modem, and a router that automatically assigns IP
addresses to computers on the network, follow the instructions
in:
■
“Setting up a DHCP IP address for Windows 2000” on
page 22
■
“Setting up a DHCP IP address for Windows 98SE or
Windows Me” on page 24.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Chapter 1: Setting Up Your Powerline Adapter
Setting up a DHCP IP address for Windows 2000
To set up a DHCP IP address for Windows 2000:
1
Click Start, Settings, then click Network and Dial-up
Connections. The Network and Dial-up Connections
window opens. This window has an icon for each
networking connection available on your computer.
For example, if you have both wired and wireless
Ethernet hardware installed on your computer, there
will be at least two icons, one for your wired Ethernet
hardware and one for your wireless Ethernet
hardware.
2
Right-click the Local Area Connection icon for the wired
Ethernet hardware, then click Properties. The Local
Area Connection Properties dialog box opens.
3
Click to select the Internet Protocol (TCP/IP) check box in
the Components checked are used by this connection list. If
you do not see TCP/IP, drag the scroll bar to see more
choices.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Step 3: Configuring the TCP/IP protocol
4
Click Properties. The Internet Protocol (TCP/IP) Properties
dialog box opens.
5
6
Click Obtain an IP address automatically.
Click OK to close the Internet Protocol (TCP/IP)
Properties dialog box.
7
8
9
Click OK to close the Local Area Connection Properties
dialog box.
Click X to close the Network and Dial-up Connections
window.
Repeat this procedure for every computer on your
network.
10 After you set up the IP addresses on all your
computers, go to “Turning the powerline adapter off”
on page 26.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Chapter 1: Setting Up Your Powerline Adapter
Setting up a DHCP IP address for
Windows 98SE or Windows Me
To set up a DHCP IP address for Windows 98SE or
Windows Me:
1
2
3
Click Start, Settings, then click Control Panel. The
Control Panel window opens.
If you are using Windows Me, click view all Control Panel
options.
Double-click the Network icon. The Network dialog box
opens.
4
Click TCP/IP -> Gateway USB Powerline Adapter (PLU-300).
-OR-
Click TCP/IP -> Gateway Ethernet Powerline Adapter
(PLE-310).
If you do not see TCP/IP, drag the scroll bar to see
more choices.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Step 3: Configuring the TCP/IP protocol
5
Click Properties. The TCP/IP Properties dialog box
opens.
6
Click the IP Address tab, then click Obtain an IP address
automatically.
7
8
9
Click OK to close the TCP/IP Properties dialog box.
Click OK to close the Network dialog box.
Click X to close the Control Panel window.
10 Repeat this procedure for every computer on your
network.
11 After you set up the IP addresses on all your
computers, go to “Turning the powerline adapter off”
on page 26.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Chapter 1: Setting Up Your Powerline Adapter
Turning the powerline adapter off
You can turn off the powerline adapter to make a computer
unavailable on the network.
To turn the PLU-300 powerline adapter off:
■
Click the remove hardware
icon in the taskbar, the
USB adapter name, then click Stop.
- OR -
Turn off your computer.
If the remove hardware icon does not appear on
the taskbar in Windows XP, click the show hidden
Important
icons
button.
To turn the PLE-310 powerline adapter off:
■
In Windows XP, click Start, then click Control Panel.
The Control Panel window opens. If your Control
Panel is in Category View, click Network and Internet
Connections. The Network and Internet Connections
window opens. Click/Double-click Network
Connections. The Network Connections window opens.
Right-click Local Area Connection, then click Disable.
- OR -
In Windows 2000, click Start, Settings, then click
Network and Dial-up Connections. The Network and
Dial-up Connections window opens. Right-click the
Local Area Connection icon for the wired Ethernet
hardware, then click Disable.
- OR -
Turn off your computer.
Windows 98SE and Windows 2000 do not provide
a method for turning off your powerline adapter
other than to turn off your computer.
Important
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Where to go from here
Where to go from here
Using your network
Now that you have created and configured your powerline
network and you know how to turn your powerline adapter on
and off, you are ready to use the network. Go to “Sharing Your
Network Resources” on page 29.
Using the Powerline Adapter
Configuration Utility
The Gateway Powerline encryption management utility lets
you find Gateway Powerline devices on the Powerline network,
measure data rate performance, and ensure privacy by setting a
user defined network private password. Go to “Using the
Powerline Adapter Configuration Utility” on page 47.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Chapter 1: Setting Up Your Powerline Adapter
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Sharing Your
2
Network Resources
After you are connected to a network you
can share access to the Internet, share
information, share peripheral devices,
and stream audio and video files. Read
this chapter to learn about:
■
■
■
“Sharing an Internet
connection” on page 30
“Sharing drives and printers”
on page 38
“Using the network” on page 43
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Chapter 2: Sharing Your Network Resources
Sharing an Internet connection
Internet sharing lets all computers on the network access the
Internet at the same time using one Internet service provider
(ISP) connection.
The Internet setup procedure uses the
Important
Windows XP New Connection Wizard and Internet
Explorer. The example screens show those
screens that typically appear in the course of using
the wizard. If your Internet connection differs from
that used in this example, you may encounter
additional screens or screens with different
selections. Make sure that you read each screen in
the wizard and make your selections based on
your particular Internet connection situation.
If you use a browser other than Internet Explorer,
see the help provided with that browser for
configuring it for use on a network.
If you are using a dial-up modem instead of a
broadband connection, see the documentation
that came with your router or access point for the
correct procedure.
Important
If you are using Windows XP, go to “Setting up Internet
Explorer in Windows XP” on page 30.
If you are using Windows 2000, Windows 98SE, or
Windows Me, go to “Setting up Internet Explorer in
Windows 2000, Windows 98, and Windows Me” on page 34.
Setting up Internet Explorer in Windows XP
To set up Internet Explorer on each computer on your
network in Windows XP:
1
Make sure that the router is turned on and configured
as instructed by your cable or DSL provider.
2
Click Start, right-click Internet, then click Internet
Properties. The Internet Properties dialog box opens.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Sharing an Internet connection
3
Click the Connections tab.
4
Click Setup. The New Connection Wizard opens.
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Chapter 2: Sharing Your Network Resources
5 Click Next. The Network Connection Type screen opens.
6
Click Connect to the Internet, then click Next. The Getting
Ready screen opens.
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Sharing an Internet connection
7
Click Set up my connection manually, then click Next. The
Internet Connection screen opens.
8
9
Click the type of Internet connection you are setting up,
then click Next.
Click Finish.
10 Repeat this procedure for each computer on your
network. Go to “Accessing the Internet from your
computer” on page 37.
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Chapter 2: Sharing Your Network Resources
Setting up Internet Explorer in Windows 2000,
Windows 98, and Windows Me
To set up Internet Explorer on each computer on your
Ethernet network in Windows 2000, Windows 98, and
Windows Me:
1
Make sure that the router is turned on and configured
as instructed by your cable or DSL provider.
2
Right-click the Internet Explorer icon on your desktop,
then click Properties. The Internet Properties dialog box
opens.
3
Click the Connections tab.
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Sharing an Internet connection
4
5
Click Setup. The Internet Connection Wizard opens.
Click I want to set up my Internet connection manually, or I want
to connect through a local area network (LAN), then click Next.
The Setting up your Internet connection screen opens.
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Chapter 2: Sharing Your Network Resources
6 Click I connect through a local area network (LAN), then click
Next. The Local area network Internet connection screen
opens.
7
Click to select the Automatic discovery of proxy server
(recommended) check box, then click Next. The Set Up Your
Internet Mail Account screen opens.
Download from Www.Somanuals.com. All Manuals Search And Download.
36
Sharing an Internet connection
8
If you want to set up an Internet e-mail account other
than the e-mail account supplied by your Internet service
provider, select Yes then click Next. Follow the on-screen
instructions to complete the Internet mail setup. When
you are finished setting up mail, click Finish.
- OR -
If you do not want to set up an e-mail account otherthan
the e-mail account supplied by your Internet service
provider, select No, click Next, then click Finish.
9
Repeat this procedure for each computer on your
network. Go to “Accessing the Internet from your
computer” on page 37.
Accessing the Internet from your computer
To access the Internet from your computer:
1
Make sure that the router is turned on.
2
Open Internet Explorer.
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Chapter 2: Sharing Your Network Resources
Sharing drives and printers
With a network, you can share drives (for example hard drives,
diskette drives, and CD or DVD drives) and printers among the
computers connected to the network.
After the drives and printers on each network computer are
shared, you can access them as though they were attached
directly to your computer. Then you can:
■
■
View a network drive
Open and copy files stored on other network
computers
■
Print documents on network printers
To share a printer among the network computers,
Important
each computer must have the shared printer’s
drivers installed. Follow the instructions included
with your printer to install the printer drivers on
each computer.
Turning on Windows file and printer
sharing
Before you can share your drives and printers, you need to turn
on Windows file and printer sharing on all the network
computers.
To turn on file and printer sharing in Windows XP and
Windows 2000:
1
In Windows XP, click Start, then click Control Panel. The
Control Panel window opens. If your Control Panel is in
Category View, click Network and Internet Connections.
-OR-
In Windows 2000, click Start, Settings, then click Control
Panel. The Control Panel window opens.
2
Click/Double-click the Network Connections or Network and
Dial-up Connections icon.
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Sharing drives and printers
3
4
Right-click the Local Area Network icon that you want
to set up file and printer sharing on, then click Properties.
Make sure that the check box for File and Printer Sharing
for Microsoft Networks is checked.
5
6
7
Click OK.
If prompted, restart your computer.
Repeat this procedure on every computer on the
network.
To turn on file and printer sharing in Windows 98SE
and Windows Me:
1
2
3
4
5
Click Start, Settings, then click Control Panel. The Control
Panel window opens.
If you are using Windows Me, click view all Control Panel
options.
Double-click the Network icon. The Network dialog box
opens.
Click File and Printer Sharing. The File and Print Sharing
dialog box opens.
Click to select the check box for the sharing options you
want.
6
7
8
9
Click OK.
Click OK.
If prompted, restart your computer.
Repeat this procedure on every computer on the
network.
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Chapter 2: Sharing Your Network Resources
Sharing drives or folders
If you want to share a drive or folder, use the following
instructions.
To share drives or folders:
1
2
Make sure that each computer on your network has
Windows file and printer sharing turned on by following
the steps in “Turning on Windows file and printer
sharing” on page 38.
Right-click the drive or folder that you want to share,
then click Sharing and Security or Sharing. The folder
properties dialog box opens.
If you share a drive, the entire contents of that drive will
be available to everyone on your network. If you share
a folder, only the contents of that folder will be available
to everyone on the network.
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Sharing drives and printers
3
Click the Sharing tab.
4
In Windows XP, if you want to share the drive or folder
with anyone on the network (network sharing), click to
select the Share this folder on the network check box.
-OR-
In Windows 2000, if you want to share the drive or folder
with anybody on the network (network sharing), click to
select the Share this folder check box.
-OR-
In Windows 98SE and Windows Me, if you want to share
the drive or folder with anybody on the network
(network sharing), click Share as.
5
Click OK.
Download from Www.Somanuals.com. All Manuals Search And Download.
41
Chapter 2: Sharing Your Network Resources
Un-sharing drives, folders, and files
If you want to un-share a drive, folder, or file, use the following
instructions.
To un-share drives or folders:
1
Right-click the drive or folder that you want to un-share,
then click Sharing and Security or Sharing.
2
In Windows XP, make sure that the Share this folder on the
network check box is not selected.
-OR-
In Windows 2000, click Do not share this folder.
-OR-
In Windows 98SE and Windows Me, click Not Shared.
Click OK.
3
Sharing printers
To share printers in Windows XP:
1
Click Start, then click Control Panel. The Control Panel
window opens. If your Control Panel is in Category View,
click Printers and Other Hardware.
2
3
Click/Double-click the Printers and Faxes icon. The Printers
and Faxes window opens.
Right-click the name of the printer you want to share,
then click Sharing.
4
5
Click Share this printer.
Click OK.
Download from Www.Somanuals.com. All Manuals Search And Download.
42
Using the network
To share printers in Windows 2000, Windows 98, and
Windows Me:
1
Click Start, Settings, then click Printers.
2
Right-click the name of the printer you want to share,
then click Sharing.
3
4
Click Shared as.
Click OK.
Using the network
After the drives and printers on each network computer are
shared, you can:
■
■
■
View shared drives and folders
Map a network drive
Open and copy files stored on other network
computers
■
Print documents on network printers
Viewing shared drives and folders
To view shared drives and folders:
1
In Windows XP, click Start, then click My Network Places.
The My Network Places window opens.
-OR-
In Windows 2000 and Windows Me, double-click the My
Network Places icon. The My Network Places window
opens.
-OR-
In Windows 98, double-click the Network Neighborhood
icon. The Network Neighborhood window opens.
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Chapter 2: Sharing Your Network Resources
2
Click/Double-click Entire Network. The Entire Network
window opens. If you do not see the contents of the
network after you double-click Entire Network, click entire
contents.
3
4
Double-click Microsoft Windows Network.
Double-click the name of your workgroup. The names of
each of the computers in your workgroup are listed. For
more information about workgroups, see “Naming the
computers and the workgroup” on page 30.
5
Double-click the name of the computer containing the
drive or folder you want to view. All shared drives and
folders are listed.
Mapping a Network Drive
After a drive or folder on one computer is mapped as a drive
on another computer, the contents of the drive or folder can
be accessed as if the drive were attached directly to the
computer.
For example, the My Documents folder on computer 1 is
mapped as the Z drive on computer 2. To access the My
Documents folder on computer 1 from computer 2, click the
Z drive icon.
To map a network drive:
1
2
3
4
Locate the drive or folder by completing the steps in
“Viewing shared drives and folders” on page 43.
Right-click the drive or folder, then click Map Network
Drive. The Map Network Drive wizard opens.
Click the arrow button to open the Drive list, then click
the drive letter you want to map this drive or folder to.
Click Finish.
Download from Www.Somanuals.com. All Manuals Search And Download.
44
Using the network
Opening files across the network
To open files across the network:
1
2
3
Start the program for the file you want to open.
Click File, then click Open.
Browse to the network drive that contains the file you
want to open.
4
Double-click the folder containing the file, then
double-click the file.
Copying files across the network
To copy files across the network:
1
In Windows XP, click Start, then click My Computer. The
My Computer window opens.
-OR-
In Windows 2000, Windows 98, and Windows Me,
double-click the My Computer icon.
2
Browse to the network drive that contains the file you
want to copy.
3
4
5
6
Browse to the file you want to copy.
Click the file.
Click Edit, then click Copy.
Double-click the folder where you want to copy the file
to.
7
Click Edit, then click Paste.
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Chapter 2: Sharing Your Network Resources
Printing files across the network
To print files across the network:
1
2
3
4
Open the file you want to print.
Click File, then click Print.
In the printer name list, click the network printer.
Click OK.
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Using the Powerline
Adapter
Configuration Utility
3
The Gateway Powerline encryption
management utility lets you find
Gateway Powerline devices on the
Powerline network, measure data rate
performance, and ensure privacy by
setting a user defined network private
password. This utility lets you set up a
network password for the local Powerline
device that is connected to the computer
where the utility is running. The
advanced utility option lets you set up a
network password remotely on other
Gateway Powerline devices through the
powerline.
For subsequent network encryption
updates, we recommend that you use the
same computer you used when you set up
the encryption utility.
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Chapter 3: Using the Powerline Adapter Configuration Utility
About the Powerline configuration utility
The Gateway Powerline encryption management utility has
four tabs to configure the Powerline settings:
■
■
■
■
Device
Network
Security
Advanced
Select a tab to customize the settings.
Before running this utility, make sure that a
Gateway Powerline device is installed correctly.
Important
Download from Www.Somanuals.com. All Manuals Search And Download.
48
About the Powerline configuration utility
Using the Device tab settings
The Device tab provides a list of your Gateway Powerline devices
that are connected to the computer that is running the
configuration utility. The utility also shows the average data
rate performance of your Powerline network. The Device tab
opens when the Powerline utility starts.
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Chapter 3: Using the Powerline Adapter Configuration Utility
Running a performance analysis
To run a performance analysis on the networked
Power Line devices:
1
Click Start, Programs, Gateway Powerline Adapter, then click
PLU-300 or PLE-310. The Gateway Powerline Adapter
Configuration Utility starts and the utility scans the
Powerline network for Powerline devices that are
connected to the network.
2
Click Refresh. The utility runs an analysis on the
networked Powerline devices’ performance. The progress
bar changes to a Link Quality status bar and indicates the
average network data rate. The color of the status bar
reflects the average performance of the Powerline
network:
■
■
■
Green = Excellent
Yellow = Fair
Red = Poor
Download from Www.Somanuals.com. All Manuals Search And Download.
50
About the Powerline configuration utility
Using the Network tab settings
The Network tab provides detailed information about each
device on the Powerline network. The list shows each Powerline
device’s Media Access Control (MAC) address and the device
data rate in mega bits per second (Mbps). Click Scan Powerline
Network to refresh the network devices information.
If your Gateway Powerline device information does
Important
not display in the device information list, make sure
that you did not change the network password to a
different network password than your current
network password. For more information, see
“Using the Security tab settings” on page 52.
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Chapter 3: Using the Powerline Adapter Configuration Utility
Using the Security tab settings
Use the Security tab to change the default network password to
a password of your choice. When you change the password, the
new password applies to the Gateway Powerline device that is
currently selected in the Powerline configuration utility.
All Powerline devices must use the same network
password.
Important
The network password must have between 4 and
24 characters. The password is case sensitive, can
include all alphabet letters, numbers, or
Important
punctuation marks. The password is required to
add new devices to the Powerline network.
Download from Www.Somanuals.com. All Manuals Search And Download.
52
About the Powerline configuration utility
Changing the Gateway Powerline private
network password
To change the Gateway Powerline private network
password:
1
Click Start, Programs, Gateway Powerline Adapter, then click
PLU-300 or PLE-310. The Gateway Powerline Adapter
Configuration Utility starts and the utility scans the
Powerline network for Powerline devices that are
connected to the network.
2
3
In the Device list, click to highlight the networked device
to change the network password.
Click Connect. The utility connects to the Powerline
device.
4
5
Click the Security tab.
Type the new password in the Networked Password box,
then click Set Local. The password changes.
6
Click OK. The utility closes.
Restoring the Gateway Powerline network
password to the default password
To restore the Gateway Powerline network password
to the default password:
1
Click Start, Programs, Gateway Powerline Adapter, then click
PLU-300 or PLE-310. The Gateway Powerline Adapter
Configuration Utility starts and the utility scans the
Powerline network for Powerline devices that are
connected to the network.
2
3
In the Device list, click to highlight the networked device
to change the network password.
Click Connect. The utility connects to the Powerline
device.
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Chapter 3: Using the Powerline Adapter Configuration Utility
4
5
Click the Security tab.
Click Restore Default. The password changes to
“HomePlug” (the default Powerline network password).
6
Click OK. The utility closes.
Using the Advanced tab settings
Use the Advanced tab to set up a network password remotely
on other computers through the powerline network.
Download from Www.Somanuals.com. All Manuals Search And Download.
54
About the Powerline configuration utility
To remotely set the network password on other
computers:
1
Click Start, Programs, Gateway Powerline Adapter, then click
PLU-300 or PLE-310. The Gateway Powerline Adapter
Configuration Utility starts and the utility scans the
Powerline network for Powerline devices that are
connected to the network.
2
3
Click the Advanced tab.
Type the private network password into the Network
Password box.
4
5
Locate the different passwords (IDs) for the other devices
you want to manage.
Type one of the passwords into the Add Password box and
click Add. The password appears in the Remote Passwords
box.
6
7
Repeat Step 5 for each password you want to add.
Click Set All to apply the private network password to all
devices listed in the Remote Passwords box.
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Chapter 3: Using the Powerline Adapter Configuration Utility
Download from Www.Somanuals.com. All Manuals Search And Download.
56
Chapter 4: Getting Help
Automated troubleshooting system
Service description
How to reach
Use an automated menu system and your telephone
keypad to find answers to common problems.
800-846-2118 (US)
877-709-2945 (Canada)
Telephone numbers
You can access the following services through your telephone
to get answers to your questions:
Resource
Service description
How to reach
Fax on
demand
support
Order a catalog of documents on
common problems, then order
documents by document numbers.
The documents will be faxed to you.
800-846-4526 (US)
877-709-2951 (Canada)
Gateway’s
fee-based
software
tutorial
Get tutorial assistance for software
issues billed by the minute.
800-229-1103 (charged
to your credit card)
900-555-4695 (charged
to your telephone bill)
service
Gateway
Technical
Support
Talk to a Gateway Technical Support
representative about a non-tutorial
technical support question.
TDD Technical Support (for hearing
impaired) is available:
800-846-2301 (US)
800-846-3609 (Canada
and Puerto Rico)
605-232-2191
(all other countries)
800-846-1778 (TDD)
Weekdays 6:00 a.m. - 8:00 p.m.
Central Time
Weekends 6:00 a.m. - 5:00 p.m.
Central Time
Sales,
accounting,
and
warranty
Get information about available
systems, pricing, orders, billing
statements, warranty service, or other
non-technical issues.
800-846-2000 (US)
888-888-2037 (Canada)
Download from Www.Somanuals.com. All Manuals Search And Download.
58
Appendix A: Safety, Regulatory, and Legal Information
Regulatory compliance statements
United States of America
Federal Communications Commission (FCC)
Unintentional emitter per FCC Part 15
This device has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio or television reception. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio
and television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
■ Reorient or relocate the receiving antenna
■ Increase the separation between the equipment and receiver
■ Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
■ Consult the dealer or an experienced radio/TV technician for
help.
Compliance Accessories: These accessories are required to be
used in order to ensure compliance with FCC rules: Standard or
custom cables that are equivalent to those that may have
shipped with your product.
Download from Www.Somanuals.com. All Manuals Search And Download.
60
FCC declaration of conformity
Responsible party:
Gateway Companies, Inc.
610 Gateway Drive, North Sioux City, SD 57049
(605) 232-2000 Fax: (605) 232-2023
Product:
■ Gateway PLU-300
■ Gateway PLE-310
This device complies with Part 15 of the FCC Rules. Operation
of this product is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by
Warning
Gateway could void the FCC compliance and negate
your authority to operate the product.
California Proposition 65 Warning
This product contains chemicals, including lead,
known to the State of California to cause cancer
Warning
and/or birth defects or reproductive harm.
Download from Www.Somanuals.com. All Manuals Search And Download.
61
Appendix A: Safety, Regulatory, and Legal Information
Notices
Copyright © 2003 Gateway, Inc.
All Rights Reserved
14303 Gateway Place
Poway, CA 92064 USA
All Rights Reserved
This publication is protected by copyright and all rights are reserved. No part
of it may be reproduced or transmitted by any means or in any form, without
prior consent in writing from Gateway.
The information in this manual has been carefully checked and is believed
to be accurate. However, changes are made periodically. These changes
are incorporated in newer publication editions. Gateway may improve
and/or change products described in this publication at any time. Due to
continuing system improvements, Gateway is not responsible for inaccurate
information which may appear in this manual. For the latest product
will Gateway be liable for direct, indirect, special, exemplary, incidental, or
consequential damages resulting from any defect or omission in this
manual, even if advised of the possibility of such damages.
In the interest of continued product development, Gateway reserves the
right to make improvements in this manual and the products it describes at
any time, without notices or obligation.
Trademark Acknowledgments
1-800-GATEWAY, ActiveCPR, ALR, AnyKey, black-and-white spot design, CrystalScan,
Destination, DestiVu, EZ Pad, EZ Point, Field Mouse, Gateway 2000, Gateway Country,
gateway.net, Gateway stylized logo, Perfect Scholar, Solo, TelePath, Vivitron, stylized
“G” design, and “You’ve got a friend in the business” slogan are registered trademarks
and black-and-white spotted box logo, GATEWAY, Gateway Astro, Gateway@Work,
Gateway Connected touch pad, Gateway Connected music player, Gateway
Cyber:)Ware, Gateway Education:)Ware, Gateway Flex Case, Gateway Gaming:)Ware,
Gateway GoBack, Gateway Gold, Gateway Learning:)Ware, Gateway Magazine,
Gateway Micro Server, Gateway Money:)Ware, Gateway Music:)Ware, Gateway
Networking Solutions, Gateway Online Network (O.N.) solution, Gateway Photo:)Ware,
Gateway Professional PCs, Gateway Profile, Gateway Solo, green stylized GATEWAY,
green stylized Gateway logo, Gateway Teacher:)Ware, Gateway Video:)Ware, HelpSpot,
InforManager, Just click it!, Learn@Gateway, Kids BackPack, SERVE-TO-ORDER,
Server Watchdog, the Spotted G Gateway Logo and the Spotted G Logo, SpotShop,
Spotshop.com, and Your:)Ware are trademarks of Gateway, Inc. Intel, Intel Inside logo,
and Pentium are registered trademarks and MMX is a trademark of Intel Corporation.
Microsoft, MS, MS-DOS, and Windows are trademarks or registered trademarks of
Microsoft Corporation. All other product names mentioned herein are used for
identification purposes only, and may be the trademarks or registered trademarks of their
respective companies.
Download from Www.Somanuals.com. All Manuals Search And Download.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN USB TO PWRLNE BRDGE GDE R0 10/03
Download from Www.Somanuals.com. All Manuals Search And Download.
|