ZV800SJ/BJ – GE Monogram36" Chimney Hood
Dimensions and Specifications (in inches)
The vent hood canopy extends forward 5-7/8".
The vent hood must be installed 24" min., and 30" max. above
the cooking surface. The telescopic duct cover conceals the
ductwork running from the top of the hood to the ceiling. The
duct cover is sized to reach 8 ft. to 10 ft. ceiling heights.
*Height to
Ceiling
The hood installation height, from the cooking surface to the
bottom of the hood, depends upon ceiling height.
1-1/2"
Before installing, consult installation
instructions packed with product, or available online at
monogram.com, for current dimensional data.
12-15/16" at sides
35-7/8"
13-11/16" at center
*The Supplied Duct Cover Fits
8 ft. to 10 ft. Ceiling Heights
Listed by
Underwriters
Laboratories
R
For answers to your Monogram,® GE Profileor
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,
800.626.2000.
Specification Created 8/04
130664
Download from Www.Somanuals.com. All Manuals Search And Download.
ZV800SJ/BJ – GE Monogram36" Chimney Hood
Cabinet Requirements
This hood may be installed beneath a wall-mounted cabinet.
Ductwork, Wiring
• Both vented and recirculating operation can be accomplished in an
• If the cabinet has been installed, it must be removed so that wall
framing supports can be added.
• Locate the Rear Wall Template packed with the literature.
• Measure 36" from the floor to the top of the cooking surface. Add
the pre-determined hood installation height. Mark that location.
• Use a level to draw a straight pencil line on the wall.
3-3/4” centerline
to wall
20” Min.
Ceiling
24” Min.
*
30” Max.
The cabinet must be at least 20" high between the bottom frame and
the inside top. A custom cabinet or modifications to a different size
cabinet may be required to accommodate the hood housing.
• The cabinet must be 36" wide.
• The cabinet must be firmly secured to wall studs or the added
framing support and capable of supporting 100 pounds.
Drill 1/8"
Drill 1/8"
Pilot Holes
Pilot Holes
Drill 1/8"
Pilot Holes
Drill 1/8"
Pilot Holes
5-1/16"
9-5/8"
13-3/4"
119-1/2”
C
12-3/4"
L
REAR WALL TEMPLATE
Drill 1/8"
Drill 1/8"
Pilot Holes
Pilot Holes
11”
ALIGN BOTTOM EDGE WITH
PENCIL LINE INDICATING
BOTTOM OF THE HOOD.
8-1/8"
2-1/16"
49-80271 JR 07-04
• Tape the template in position along the penciled line. Check to be
sure the template is level.
• Use the level to draw a line straight up, from the centerline on the
template to the ceiling.
-4
11-3/4”
• Measure 3-3/34" from the back wall to the centerline of a 6-1/2"
hole on the ceiling.
NOTE: If drywall is not present, add drywall thickness to the
3-3/4" dimension.
Listed by
Underwriters
Laboratories
R
House Wiring Location:
For answers to your Monogram,® GE Profileor
GE® appliance questions, visit our website at
ge.com or call GE Answer Center® service,
800.626.2000.
• The junction box is located on the top right side of the hood.
• Wiring should enter the back wall 20" to 26" above the bottom of
the hood, and within 4" of the right side of the centerline. Wiring
should enter at least 4" above the bracket on the right side.
Specification Created 8/04
130664
Download from Www.Somanuals.com. All Manuals Search And Download.
ZV800SJ/BJ – GE Monogram36" Chimney Hood
• Under-cabinet or stand-alone installation – The chimney
hood installs beneath a cabinet, above most cooktops
and ranges. For a more contemporary look, the system
can be wall-mounted with matching 8-to-10-ft. duct cover.
• Low-profile design. High-impact style – The retractable
glass canopy is sleekly styled with a streamlined design,
seamlessly finished edges and front-mounted touch
• Powerful ventilation – A four-speed, 500-CFM fan blower
with boost option captures the smoke and steam produced
by high-performance cooking equipment.
• Multilevel halogen lighting – Six levels of intensity, from
accent to ambient settings, allow you to choose the lighting
to match the cooking task or occasion.
• Easy maintenance – Stainless steel filters can be easily
removed for safe cleaning in your dishwasher.
• Recirculating kit – Included for applications that do not
allow outside venting.
Specification Created 8/04
130664
Download from Www.Somanuals.com. All Manuals Search And Download.
|