®
Monogram
Use and Care Guide
for Side-by-Side
36″, 42″, 48″
Built-In
Refrigerators
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Information
Built - In Refrigerators
You’ll see them on a label above the
freezer compartment behind the top
panel.
Before sending in this card, please write
these numbers here:
Write
down the
model &
serial
These numbers are also on the Consumer
Product Ownership Registration Card
included with this guide.
Model Number
numbers
Serial Number
Use these numbers in any correspondence
or service calls concerning your
refrigerator.
If you
Immediately contact the dealer (or
builder) that sold you the refrigerator.
received a
damaged
refrigerator
Save time
& money
Before you request service, check the
Problem Solver in the back of this guide.
It lists causes of minor operating problems
that you can correct yourself.
If you
need
service
To obtain service, see the Consumer
Services page in the back of this guide.
For customers in Canada:
FIRST, contact the people who serviced
We’re proud of our service and want you to your appliance. Explain why you are not
be pleased. If for some reason you are not
happy with the service you receive, here
are steps to follow for further help.
pleased. In most cases, this will solve the
problem.
NEXT, if you are still not pleased, write all
the details—including your phone number
to:
FIRST, contact the people who serviced
your appliance. Explain why you are not
pleased. In most cases, this will solve the
problem.
Manager, Consumer Relations
Camco Inc.
1 Factory Lane, Suite 310
Moncton, N.B. E1C 9M3
NEXT, if you are still not pleased, write
all the details—including your phone
number—to:
Manager, Consumer Relations
GE Appliances
Appliance Park
Louisville, KY 40225
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
• If your refrigerator has an automatic
w WARNING—When using this
appliance, always exercise basic safety
precautions, including the following:
• Use this appliance only for its intended
purpose as described in this Use and
Care Guide.
icemaker, avoid contact with the moving
parts of the ejector mechanism, or with
the heating element that releases the
cubes. Do not place fingers or hands on
the automatic icemaking mechanism
while the refrigerator is plugged in.
• This refrigerator must be properly
installed in accordance with the
• Unplug your refrigerator before cleaning
and making repairs. NOTE: We strongly
recommend that any servicing be
Installation Instructions before it is used.
performed by a qualified individual.
• Do not allow children to climb, stand or
hang on the shelves in the refrigerator.
They could damage the refrigerator and
seriously injure themselves.
• Before replacing a burned-out light bulb,
the refrigerator should be unplugged in
order to avoid contact with a live wire
filament. (A burned-out light bulb may
break when being replaced.) NOTE:
Turning control to “0” does not remove
power to the light circuit.
• After your refrigerator is in operation, do
not touch the cold surfaces in the freezer
compartment, particularly when hands
are damp or wet. Skin may adhere to
these extremely cold surfaces.
• Do not refreeze frozen foods which have
thawed completely.
• Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
wDANGER: RISK OF CHILD ENTRAPMENT
Child entrapment and suffocation are
not problems of the past. Junked or
abandoned refrigeration products are still
dangerous. . . even if they will sit for “just
a few days.” If you are getting rid of your
old appliance, please follow these
Before You Throw Away Your Old
Refrigeration Product:
• Take off the doors.
• Leave the shelves in place so that children
may not easily climb inside.
instructions to help prevent accidents.
CFC DISPOSAL
Old refrigeration products have
cooling systems that used CFCs
(chlorofluorocarbons). CFCs are
believed to harm stratospheric ozone.
If you are throwing away an old
refrigeration product, make sure the CFC
refrigerant is removed for proper disposal
by a qualified servicer. If you intentionally
release this CFC refrigerant you can be
subject to fines and imprisonment under
provisions of environmental legislation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
LIRE ET CONSERVER CES INSTRUCTIONS
• Si votre réfrigérateur est doté d’une
w
AVERTISSEMENT : Lorsque vous
utilisez le réfrigérateur, observez
toujours certaines précautions de base,
notamment:
machine à glaçons automatique, évitez le
contact avec les pièces mobiles du
mécanisme éjecteur, ou avec l’élément
chauffant qui libère les glaçons. Ne
posez pas les doigts ou les mains sur le
mécanisme de la machine à glaçons
pendant que le réfrigérateur est
branché.
• N’utilisez le réfrigérateur que pour son
usage prévu, comme décrit dans le
présent guide.
• Installez le réfrigérateur conformément
aux directives d’installation avant de
l’utiliser.
• Débranchez votre réfrigérateur avant
de le nettoyer et de le réparer.
REMARQUE : Nous vous
recommandons vivement de confier
toute réparation à un technicien
qualifié.
• Ne laissez pas les enfants grimper,
s’asseoir, se tenir debout ni se pendre
aux clayettes du réfrigérateur. Ils
pourraient endommager le réfrigérateur
et se blesser gravement.
• Avant de remplacer une ampoule grillée,
le réfrigérateur doit être débranché afin
d’éviter tout contact avec un fil sous
tension. (Une ampoule grillée peut
se briser pendant l’opération).
REMARQUE : Lorsque vous placez
la commande sur «0» (éteint),
l’alimentation électrique de l’ampoule
n’est pas coupée.
• Une fois le réfrigérateur en marche, ne
touchez pas les surfaces froides du
congélateur, surtout si vous avez les
mains humides ou mouillées : la peau
risque d’adhérer à ces surfaces très
froides.
• N’entreposez et n’utilisez pas d’essence
ou autres vapeurs et liquides
inflammables à proximité de cet appareil
ou de tout autre appareil
• Ne faites PAS recongeler des aliments
surgelés qui ont complètement dégelé.
électroménager.
wDANGER! RISQUES POUR LES ENFANTS
Les enfants pris au piège ou morts d’asphyxie
sont toujours d’actualité. Les appareils de
réfrigération abandonés sont toujours aussi
dangereux, même si on n’attend que “quelque
jours” pour s’en débarasser. Si vous ne gardez
pas votre ancien appareil, veuillez suivre les
directives ci-dessous afin de prévenir les
accidents.
Avant de vous débarasser de votre vieux
appareil de réfrigération:
• Démontez les portes.
• Laissez les clayettes en place afin d’empêcher
les enfants de grimper à l’intérieur.
SE DÉBARRASSER DU CFC
Les vieux appareils de réfrigération ont un
avec CFC soit enlevé correctement par un
système de refroidissement qui a utilisé les CFC technicien qualifié. Si vous libérez
(chlorofluorocarbones). Les CFCs sont jugés
nocifs pour l’ozone stratosphérique.
intentionnellement ce frigogène avec CFC vouz
pouvez être soumis aux contraventions et à
l’emprisonnement après les stipulations des
lois sur l’environment.
Si vous débarrassez de votre viel appareil de
réfrigération, assurez-vous que le frigorigène
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or
The appliance should always be plugged
remove the third (ground) prong from the into its own individual electrical outlet
power cord. For personal safety, this
appliance must be properly grounded.
which has a voltage rating that matches
the rating plate. This provides the best
performance and also prevents
overloading house wiring circuits
which could cause a fire hazard from
overheated wires.
The power cord of this appliance is
equipped with a 3-prong (grounding)
plug which mates with a standard 3-prong
(grounding) wall outlet to minimize the
possibility of electric shock hazard from
this appliance.
Never unplug an appliance by pulling
on the power cord. Always grip the
plug firmly and pull straight out from
the outlet.
Have the wall outlet and circuit checked
by a qualified electrician to make sure the
outlet is properly grounded.
Repair or replace immediately all power
cords that have become frayed or
otherwise damaged. Do not use a cord
that shows cracks or abrasion damage
along its length or at either end.
Where a standard 2-prong wall outlet
is encountered, it is your personal
responsibility and obligation to have it
replaced with a properly grounded
3-prong wall outlet.
When moving the appliance, be careful
not to roll over or damage the power cord.
DO NOT USE AN ADAPTER PLUG TO
CONNECT THE REFRIGERATOR TO
A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD
WITH THIS APPLIANCE.
SAVE THESE INSTRUCTIONS
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
RACCORDEMENT ÉLECTRIQUE
Ne coupez ni retirez en aucun cas la
troisième broche (mise à la terre) de la
fiche du cordon d’alimentation. Pour
votre sécurité, cet appareil doit être
correctement mis à la terre.
Cette précaution est recommandée pour
garantir un rendement optimum et éviter
une surcharge des circuits électriques de
la résidence, ce qui pourrait créer un
risque d’incendie par surschauffe des fils.
Ne débranchez jamais l’appareil en
tirant le cordon d’alimentation.
Le cordon d’alimentation de cet appareil
est muni d’une fiche à 3 broches (mise à la
terre) qui se branche dans une prise
mural ordinaire à 3 alvéoles (mise à la
terre) pour réduire au minimum les
risques du chocs électriques.
Saisissez fermement la fiche du cordon
et tirez droit pour la retirer de la prise.
Réparez ou remplacez immédiatement
tout cordon effiloché ou endommagé.
N’utilisez pas un cordon fendillé ou
présentant des signes d’usure.
Faites examiner la prise de courant et le
circuit par un électricien qualifié pour
vous assurer que la prise est correctement
mise à la terre.
Lorsque vous déplacez l’appareil du mur,
faites attention de ne pas la faire rouler
sur le cordon d’alimentation afin de ne
pas l’endommager.
Si la prise murale est du type standard
à 2 alvéoles, il vous incombe de la faire
remplacer par une prise à 3 alvéoles
correctement mise à la terre.
La machine à glaçons doit toujours être
branché dans sa propre prise de courant,
dont la tension nominale est identique à
celle indiquée sur la plaque signalétique.
N’UTILISEZ PAS UNE FICHE
D’ADAPTATION POUR RACCORDER
LE RÉFRIGÉRATEUR DANS UNE
PRISE MURALE À 2 ALVÉOLES.
N’UTILISEZ PAS DE CORDONS
PROLONGATEURS AVEC CET
APPAREIL.
CONSERVEZ CES DIRECTIVES
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Built - In Refrigerators
Set Temperature
Controls
(appearance
may vary)
Your refrigerator has two controls that let
you regulate the temperature in the fresh
food and freezer compartments.
5 IS NORMAL
9 IS COLDEST
5 IS NORMAL
9 IS COLDEST
5
5
FRESH FOOD
FREEZER
They have settings from 1 through 9,
and are located at the top of the fresh
food compartment.
The freezer control also has
an OFF setting.
9 is the coldest setting, 1 is the warmest.
WHEN YOU FIRST TURN THE
REFRIGERATOR ON, SET BOTH
CONTROLS AT 5.
For colder or warmer temperatures,
adjust the desired compartment control
1 number at a time.
IMPORTANT: When first setting
controls, or adjusting them, allow 24
hours for the refrigerator to get cold.
Note: Turning the freezer control to the
OFF position stops cooling in BOTH
compartments—fresh food AND freezer—
but does not shut off power to the
refrigerator.
How to test
temperatures
Use the milk test for the fresh food
compartment. Place a container of milk
on the top shelf in the fresh food
compartment. Check it a day later.
If the milk is too warm or too cold,
adjust the temperature controls.
Use the ice cream test for the freezer
compartment. Place a container of ice
cream in the center of the freezer
compartment. Check it after a day.
If it’s too hard or too soft, adjust the
temperature controls.
Always allow 24 hours for the refrigerator
to reach the temperature you set.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Built - In Refrigerators
The energy saver switch is located on the
temperature control panel.
To reduce the amount of electricity
required to operate your refrigerator,
push switch to ENERGY SAVER setting.
This turns off the heater in your
refrigerator that prevents moisture from
forming on the outside of the refrigerator.
With the heater turned off, there is a
chance that moisture may form on the
outside of your refrigerator, especially
when the weather is humid.
The humidity is most likely to be high in
the summer, in the early morning hours,
and in homes which are not air
conditioned.
Over an extended period of time,
moisture that forms on the refrigerator
surface may cause deterioration of the
paint finish. It will be important to protect
the finish by using appliance polish wax as
described in the Care and Cleaning
section.
Move the energy saver switch from the
ENERGY SAVER setting and electricity
flows through the low wattage heater
which warms the outside of the
refrigerator. Under most conditions, this
prevents the forming of moisture or water
droplets.
Energy saver
switch
It is not necessary to defrost the freezer or
fresh food compartments. Although your
refrigerator is designed and equipped to
defrost itself automatically, some frost on
packages is normal.
No defrosting
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic Icemaker (on some models)
Built - In Refrigerators
A newly-installed refrigerator may take 8 to • going away on vacation, at which time
Automatic
icemaker
(on some
models)
12 hours to begin making ice.
you should also turn off the valve in the
water supply line to your refrigerator.
The icemaker will produce eight cubes
per cycle—approximately 100 cubes in a
24-hour period, depending on freezer
compartment temperature, room
temperature, number of door openings
and other use conditions.
If your refrigerator is operated before
the water connection is made to the
icemaker, keep the feeler arm in the
STOP (up) position.
When the refrigerator has been connected
to the water supply, move the feeler arm
to the ON (down) position.
The ice maker will fill with water when
it cools to freezing. A newly-installed
refrigerator may take 8 to 12 hours to
begin making ice cubes.
• turning the freezer control to the OFF
position.
If ice is not used frequently, old ice cubes
will become cloudy and taste stale. Empty
the ice storage bin periodically and wash
it in lukewarm water. Be sure to allow the
storage bin to dry before replacing it—
otherwise ice cubes may stick to other
parts of the icemaker.
If this is your first icemaker, you’ll hear
occasional sounds that may be unfamiliar.
They are normal icemaking sounds and
are not a cause for concern.
Feeler arm in
STOP (up)
position
Icemaker
Throw away the first few batches of ice.
This flushes away impurities in the
water line.
Icemaking will continue until the feeler
arm senses enough ice cubes in the
storage bin. For maximum ice production,
level the stored cubes with your hand
occasionally. Be sure nothing interferes
with the swing of the feeler arm.
Ice
Storage
Bin
The icemaker ejects cubes in groups of
eight and it is normal for several cubes
to be joined together.
Move the icemaker feeler arm to the STOP
(up) position when:
Feeler arm
in ON
(down)
position
• home water supply is to be off for several
hours.
• ice storage bin is to be removed for a
period of time.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Ice & Water Dispenser (on some models)
Built - In Refrigerators
Select CUBES, CRUSHED ICE (on some
models) or WATER.
To use the
dispenser
Press the rim of the glass gently against the
dispenser pad.
The spill shelf is not self-draining. To
reduce water spotting, the shelf and its
grille should be cleaned regularly.
If no water is dispensed when the
refrigerator is first installed, there may
be air in the water line system. Press the
dispenser pad for at least two minutes to
remove trapped air from the water line
and to fill the water system. To flush out
impurities in the water line, throw away
the first six glassfuls of water.
Spill Shelf
To remove:
Ice storage
bin
Lift the left corner to free the bin from
the shelf and pull the bin straight out
while supporting it at front and rear.
To replace:
Slide the bin back until the tab on the bin
locks into the slot on the shelf. If the bin
does not go all the way back, remove it
and rotate the drive mechanism 1/4 turn.
Then push the bin back again.
Rotate
Drive
Mechanism
CAUTION: Never put fingers or
any other objects into the ice crusher
discharge opening.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Ice & Water Dispenser (on some models)
Built - In Refrigerators
• Add ice before filling the glass with a
• Some crushed ice may be dispensed
even though you selected CUBES. This
happens occasionally when a few cubes
accidentally get directed to the crusher.
Important
facts about
your ice
& water
dispenser
beverage. This will prevent splashing,
which could cause the ice selector switch
to stick or bind.
• Do not add ice from trays or bags to
the storage bin. It may not crush or
dispense well.
• After crushed ice is dispensed, some
water may drip from the chute.
• Sometimes a mound of snow will
form on the door in the ice chute.
This condition is normal and usually
occurs when you have dispensed
crushed ice repeatedly. The snow
will eventually evaporate.
• Avoid overfilling glass with ice and use
of narrow or extra-tall glasses. Backed-up
ice can jam the chute or cause the door
in the chute to freeze shut. If ice is
blocking the chute, poke it through with
a wooden spoon.
• Dispensed water is not ice cold.
For colder water, simply add crushed
ice or cubes before dispensing water.
• Beverages and foods should not be
quick-chilled in the ice storage bin.
Cans, bottles or food packages in the
storage bin may cause the icemaker or
auger to jam.
• The first glass of water dispensed may
be warmer than the following ones.
This is normal.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage Drawers
Built - In Refrigerators
Excess water that may accumulate in the
bottom of the drawers should be emptied
and the drawers wiped dry.
Storage
drawers
Fruit and
vegetable
drawers
The storage drawers at the bottom of the
fresh food compartment are designed to
provide high humidity levels required by
most vegetables and lower humidity levels
required for most fruits.
When replacing the drawers, always push
them all the way in.
Storage time will depend upon the type of
food and its condition when placed in the
drawers.
This refrigerated drawer is designed to
keep unwrapped foods fresh by retaining
the natural moisture content of foods
such as:
As in any refrigerated storage area, it is
recommended that foods with strong
odors be stored wrapped—foods such as:
High
humidity
setting
• Broccoli
• Brussels
sprouts
• Cabbage
• Cauliflower
• Green onions
• Parsnips
• Turnips
• Artichokes
• Asparagus
• Beets, topped
• Blueberries
• Currants
• Celery
• Cherries
• Corn
• Currants
• Greens, leafy
• Lettuce
• Parsley
• Peas, green
• Radishes
• Rhubarb
• Spinach
• Carrots
• Tomatoes, ripe
This refrigerated drawer is designed
to provide lower humidity storage for
items such as:
Low
humidity
setting
• Apples
• Nectarines
• Oranges
• Peaches
• Pears
• Raspberries
• Squash, summer
• Strawberries
• Tangerines
• Apricots
• Grapes
• Mushrooms
The Sealed Snack Pan retains high
humidity for the convenient storage of
lunch meats and cheese, hors d’oeuvres,
spreads and snacks.
Sealed
snack pan
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Storage Drawers
Built - In Refrigerators
Drawers at the bottom of the fresh food
compartment will stop before coming all
the way out of the refrigerator, to help
prevent contents from spilling onto floor.
Drawer
removal
To remove a drawer, pull the drawer out.
Lift the front of the drawer up and out of
the wire holder. Lift the back of the drawer
up and out.
To remove the drawers when the
refrigerator door cannot be opened fully,
the shelf above the drawers must be
removed. Push the shelf back then lift up.
Tilt the cover and take it out.
To replace a drawer, place the back of the
drawer in the wire holder, making sure the
extensions of the side of the drawer fit into
the back of the wire holder. Lower the
front of the drawer into the wire holder.
Press firmly on the top of the drawer.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Shelves
Built - In Refrigerators
Tempered glass shelves in the fresh food
compartment and steel wire shelves in
the freezer compartment are adjustable,
enabling you to make efficient shelf
arrangements to fit your family’s food
storage needs.
To replace shelves:
How to
rearrange
your shelves
Select desired shelf height. With shelf
front raised slightly, engage top lugs in
tracks at rear of cabinet. Then lower front
of shelf until it locks into position.
To remove shelves:
Tilt shelf up at front, then lift it up and
out of tracks on rear wall of refrigerator.
Some door shelves are adjustable and
can be moved up and down to meet
your storage needs.
Door
shelves
Divider
To remove: Lift the shelf up and slide it
towards you.
The divider (on some models) helps
prevent tipping, spilling or sliding of small
items stored on the door shelf.
Place index finger and middle finger on
either side of the divider near the front
and simply move it back and forth to fit
your needs.
Quick space
shelf
This shelf splits in half and slides under
itself for storage of tall items on the shelf
below.
Removable
wine rack
(on some
models)
The wine rack is designed to hold a bottle
on its side. A good location for the wine
rack is the Quick Space Shelf.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Shelves
Built - In Refrigerators
This shelf has only one position on
the door.
To remove: Lift the shelf up and slide it
towards you.
Deep door
shelf
This swing-down shelf provides extra shelf
space when needed.
Quick shelf
When you want to use it, pull the shelf
forward as far as it goes, then lower it.
Be careful not to force it down before
it is pulled out all the way.
To raise it back into position, pull the shelf
forward, push it up and slide it back fully
until it stops.
Wire slide-out freezer baskets can be
Freezer
Baskets
pulled out for easy access to frozen foods.
To remove: Pull shelf out. Lift the front of
the basket up and then take it out.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
Built - In Refrigerators
The water and ice
The door handles and trim can be cleaned
with a cloth dampened with a solution of
mild liquid dishwashing detergent and
water. Dry with a soft cloth. Don’t use wax
on the door handles or trim.
The stainless steel panels and door handles
(on some models) can be cleaned with a
commercially available stainless steel
cleaner using a clean, soft cloth.
Press here to
remove grille
Cleaning
outside
dispenser spill shelf
should be wiped dry
immediately to prevent
spotting. The grille is
easily removed by
pressing on the back right corner. Water
left on the shelf may leave deposits that you
can remove by soaking in undiluted
vinegar. You can also use a paste of non-
precipitating water softener (such as
Do not use appliance wax or polish on the
stainless steel.
Calgon brand) and water, or 1 teaspoon of
citric acid powder per pint of hot tap water.
Soak until the deposit disappears or
becomes loose enough to rinse away.
Usually 30 minutes soaking time is
adequate. Avoid using wax on the spill shelf
and trim.
Inside the fresh food and freezer
compartments should be cleaned at least
once a year. Unplug the refrigerator
before cleaning. If this is not practical,
wring excess moisture out of sponge or
cloth when cleaning around switches,
lights or controls.
Avoid cleaning cold glass shelves with hot
water because the extreme temperature
difference may cause them to break.
Cleaning
inside
To help prevent odors, leave
an open box of baking soda in
the rear of the refrigerator, on
the top shelf. Change the box
Use warm water and baking soda solution— every 3 months. An open box
about a tablespoon of baking soda to a
quart of water. This both cleans and
neutralizes odors. Rinse thoroughly with
water and wipe dry.
Other parts of the refrigerator—including
door gaskets, meat and vegetable drawers,
ice storage bin and all plastic parts—can be
cleaned the same way. After cleaning door
gaskets, apply a thin layer of petroleum
jelly to the door gaskets at the hinge side.
This helps keep the gaskets from sticking
and bending out of shape. Do not use
cleansing powders or other abrasive
cleaners.
of baking soda in the freezer
will absorb stale freezer odors.
Do not wash any plastic parts from your
refrigerator in your automatic dishwasher.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
Built - In Refrigerators
To clean the condenser fins:
Cleaning the
condensor
fins
Decorative panel
First turn off the power at the circuit
breaker or fuse box. Wait about 30 minutes
for the condenser area to cool. Then
remove the decorative panel by lifting up
and toward you.
Use a soft bristle brush to loosen dust and
lint on the condenser fins. Use a vacuum
hose to remove soil.
Condenser fins
Plug
After cleaning: Reconnect power at the
fuse box or circuit breaker.
Replace the decorative panel.
Condenser fins
For extended vacations or absences,
remove food and shut off power to the
refrigerator at the fuse box or circuit
breaker. Clean the interior with a baking
soda solution of 1 tablespoon of soda to
1 quart of water. Wipe dry. To prevent
odors, leave an open box of soda in the
refrigerator. Leave doors open.
For shorter vacations, remove perishable
foods and leave controls at regular settings.
However, if the room temperature is
expected to drop below 60°F., follow the
same instructions as for extended
vacations.
Move the icemaker feeler arm to the STOP
(up) position and be sure to shut off the
water supply to the refrigerator.
Preparing
for vacation
Preparing
to move
Secure all loose items such as grille,
shelves and drawers by taping them
securely in place to prevent damage.
Be sure the refrigerator stays in an upright
position during moving.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
Built - In Refrigerators
There are upper and lower light bulbs in
the fresh food compartment.
To replace a bulb:
1. Turn off power at the circuit breaker or
fuse box.
Light bulb
replacement in
the fresh food
compartment
2. Remove the light shield from the top
fresh food light by pushing the front end
up and pulling it toward you to release it
from the rear retaining lip. (It may bend
slightly.)
To change the bottom refrigerator light,
pull out the top drawer, look to the rear of
the fresh food compartment and replace
bulb as needed.
3. Replace with the same size bulb,
reinstall the shield for the upper fresh
food light, and turn the power on.
To reinstall the upper fresh food shield,
hook the front edge first, then push it up
and back until the shield rests in place.
To replace a bulb:
1. Turn off power at the circuit breaker or
fuse box.
2. Remove the freezer light shield by
pulling the front edge down and free
and then pull it toward you.
Light bulb
replacement in
the freezer
compartment
3. Replace with the same size bulb,
reinstall the shield, and turn the
power on.
To replace the freezer shield, set the back
edge on the rear tabs and then push up in
the front until it rests in place.
You may bend the shield slightly to help in
removal and replacement.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Built - In Refrigerators
INSTALLATION REQUIREMENTS
IMPORTANT…Please Read Carefully.
Refrigerator
location
Do not install refrigerator where
temperature will be below 60°F (16°C)
because it will not run often enough to
maintain proper temperatures.
Do install it on a floor strong enough to
support a fully loaded refrigerator.
Clearances
Leveling
If the refrigerator is to be installed in a
corner, allow 2″ between the hinges of the
refrigerator and the wall to ensure a 90°
door opening capability.
No other clearances at top, sides, or back
are required.
This model has 4-point leveling. All 4
corners are supported by leveling legs.
The front wheels are non-adjustable; they
are only used for positioning the unit.
Hex nut
• To level the back of the unit, turn hex
nut located above the front wheels.
• To level the front of the unit,
1
use a 1 ⁄4″ open end wrench and
adjust the leveling legs.
Leveling leg
• Turn hex nut or front leveling
leg clockwise to raise the unit,
counter-clockwise to lower
the unit.
Wheel
See the Installation Instructions
(Pub. No. 49-6473—36), (Pub. No. 49-
6462—42), (Pub. No. 49-6457—48) for
complete directions.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
The Problem Solver
Built - In Refrigerators
PROBLEM
POSSIBLE CAUSE
Questions?
Use this
problem
solver!
Refrigerator does
not operate
• May be in defrost cycle when motor does not operate for about
30 minutes.
• Freezer control is in the OFF position.
• If the interior light is not on, the refrigerator may not be plugged
in at the wall outlet.
• If the plugs are secure and the refrigerator still fails to operate,
plug a lamp into the same outlet to determine if there is a tripped
circuit breaker or burned-out fuse.
Motor operates for
long periods
• Modern refrigerators with more storage space and a larger
freezer compartment require more operating time.
• Normal when refrigerator is first delivered to your home—usually
requires 24 hours to completely cool down.
• Large amounts of food placed in refrigerator to be cooled
or frozen.
• Hot weather—frequent door openings.
• Door left open.
• Temperature controls are set too cold.
• Condenser needs cleaning.
Motor starts and stops
frequently
• Temperature control starts and stops motor to maintain
even temperatures.
Vibration or rattling
• If refrigerator vibrates, more than likely it is not resting solidly
on the floor. The front leveling legs need adjusting, or floor is
weak or uneven. Adjust leveling legs or call your installer.
• If dishes vibrate on shelves, try moving them.
Slight vibration is normal.
Operating sounds
• The high speed compressor motor required to maintain near zero
temperatures in the large freezer compartment may produce
higher sound levels than your old refrigerator.
• Normal fan air flow—one fan blows cold air through the
refrigerator and freezer compartments—another fan cools
the compressor motor.
These NORMAL sounds will also be heard from time to time:
• Defrost timer switch clicks at defrost.
• Defrost water dripping.
• Temperature control clicks ON or OFF.
• Refrigerant boiling or gurgling.
• Cracking or popping of cooling coils caused by expansion
and contraction during defrost and refrigeration
following defrost.
• Ice cubes dropping into the bin and water running in
pipes as icemaker refills.
Foods dry out
• Foods not covered, wrapped or sealed properly.
• Temperature control not set cold enough.
• Warm weather—frequent door openings.
• Door left open for too long a time.
• Package may be holding door open.
21
Fresh food
or freezer
compartment
too warm
Download from Www.Somanuals.com. All Manuals Search And Download.
The Problem Solver
Built - In Refrigerators
PROBLEM
POSSIBLE CAUSE
Questions?
Use this
problem
solver!
Doors not
closing
properly
• Refrigerator not level. Adjust leveling legs or call the
installer. When cabinet is level, doors will close gently
and securely.
Frost or ice
crystals on
frozen food
• Door may have been left ajar or package holding door open.
• Too frequent or too long door openings.
• Frost within package is normal.
Automatic icemaker
does not work
• Icemaker feeler arm in STOP (up) position.
• Water supply turned off or not connected.
• Freezer compartment too warm.
• Cubes too small—water shutoff valve connecting refrigerator
to home water line may be clogged.
• Sometimes cubes fuse to the side of the ice mold and hold
the feeler arm in the STOP (up) position. Remove this ice
to restart the icemaker.
• When reaching for cubes by hand, you may have pushed the
feeler arm into the STOP (up) position by mistake.
• Piled up cubes in storage bin may cause icemaker to shut
off prematurely. With icemaker feeler arm in STOP (up)
position, level cubes in bin by hand.
Slow ice cube
freezing
• Door may have been left open.
• Turn temperature of freezer compartment colder.
Ice cubes have
odor/taste
• Old cubes need to be discarded.
• Ice storage bin needs to be emptied and washed.
• Unsealed packages in refrigerator and/or freezer
compartments may be transmitting odor/taste to ice cubes.
• Interior of refrigerator needs cleaning.
• Poor-tasting incoming water. Install a water filter.
Cube dispenser
does not work
• No ice cubes. Remove storage bin. If cubes are frozen to wire
arm, remove cubes.
• No ice cubes. Icemaker turned off or water supply
turned off.
• Irregular ice clumps in storage container. Break up as
many as you can with fingertip pressure and discard the
remaining clumps.
Water has poor
taste/odor
• If water dispenser has not been used for an extended
period, dispense water in regular manner until all water in
reservoir is replenished with fresh water.
• Poor-tasting incoming water. Install a water filter. See the
Water Filter Accessory section.
Water in first glass
is warm
• Allow about 24 hours for water to cool to proper
temperature after refrigerator is first installed.
• If water dispenser has not been used for extended
period, water in the first glass will not be as cool as
in succeeding glasses.
• If water reservoir has been drained, allow several hours
for replenished supply to chill.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
The Problem Solver
Built - In Refrigerators
PROBLEM
POSSIBLE CAUSE
Questions?
Use this
problem
solver!
Ice clumps form
in the storage bin
• If you don’t use the ice very often, ice clumps may form
in the storage bin and can clog the dispenser. Remove the
storage bin from the freezer and break up ice clumps with
your hands. Throw away any clumps that you can’t break up.
Water dispenser
does not work
• Water supply line turned off or not connected.
• Supply line may be clogged with sediment.
• If no water is dispensed when the icemaker is first installed,
there may be air in the water system. Press the dispenser pad
for at least two minutes to remove trapped air from the
water line and to fill the water system.
Moisture forms on
cabinet surface
between the doors
• Not unusual during periods of high humidity. If problem
persists, call for service.
Moisture
collects inside
• Too frequent or too long door openings.
• In humid weather, air carries moisture into refrigerator
when doors are opened.
Water on the floor
• If you use a glass over 6 inches tall, you may be jamming the
cubes in the funnel chute. They can fuse inside the chute
and drop out later, leaving water or ice on the floor.
Rrefrigerator has odor
• Foods with strong odors should be tightly covered.
• Check for spoiled food.
• Interior needs cleaning.
• Keep open box of baking soda in refrigerator; replace every
3 months.
Interior light does
not work
• No power at outlet. Call installer or electrician.
• Light bulb needs replacing.
• Check fuse and circuit breaker.
Uneven spacing or
gaps between doors
and kitchen cabinet
• Kitchen cabinets are not level or square. Call the
installer or cabinetmaker.
Poor door alignment
or one door higher
than the other
• Refrigerator not level. Adjust leveling legs so refrigerator
is resting solidly on the floor and is level side to side
and front to back.
If you need more help…call toll free:
GE Answer Center , 800.626.2000
®
consumer information service
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Services
Built-In Refrigerator
With the purchase of your new Monogram appliance, receive the
assurance that if you ever need information or assistance from GE,
we will be there. All you have to do is call—toll- free!
GE Answer
Center®
Whatever your question about any Monogram major appliance, GE Answer Center®
information service is available to help. Your call—and your question—will be answered
promptly and courteously. And you can call any time. GE Answer Center® service is open
24 hours a day, 7 days a week.
In the USA:
800.626.2000
In Canada, call 1.888.880.3030.
In-Home Repair
Service
A GE consumer service professional will provide expert repair service, scheduled at a time
that’s convenient for you. Many GE Consumer Service company-operated locations offer
you service today or tomorrow, or at your convenience (7:00 a.m. to 7:00 p.m. weekdays,
9:00 a.m. to 2:00 p.m. Saturdays). Our factory-trained technicians know your appliance
inside and out—so most repairs can be handled in just one visit.
In the USA:
800.444.1845
In Canada:
1.888.880.3030
For Customers
With Special
Needs…
GE offers Braille controls for a variety of GE appliances, and a
brochure to assist in planning a barrier-free kitchen for persons
with limited mobility.
Consumers with impaired hearing or speech who have access to a
TDD or a conventional teletypewriter may call 800.TDD.GEAC
(800.833.4322) to request information or service.
In the USA:
800.626.2000
Service Contracts
You can have the secure feeling that GE Consumer Service will still be there after your
warranty expires. Purchase a GE contract while your warranty is still in effect and you’ll
receive a substantial discount. With a multiple-year contract, you’re assured of future
service at today’s prices.
In the USA:
800.626.2224
In Canada:
1.888.880.3030
Parts and
Individuals qualified to service their own appliances can have parts or accessories sent directly
to their home. The GE parts system provides access to over 47,000 parts…and all GE Genuine
Renewal Parts are fully warranted. VISA, MasterCard and Discover cards are accepted.
Accessories
In the USA:
800.626.2002
User maintenance instructions contained in this guide cover procedures intended to be
performed by any user. Other servicing generally should be referred to qualified service
personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
In Canada:
1.888.880.3030
24
Download from Www.Somanuals.com. All Manuals Search And Download.
o d a y M a i l T
I m p o r t a n t
e g i s t r a t i o n O w n e r s h i p R
C o n s u m e r P
G E A p p l i a n c e s
Place
1st Class
Letter
Stamp
Here
General Electric Company
Warranty Registration Department
P.O. Box 32150
Louisville, KY 40232-2150
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us. We are proud to
have you as a customer!
Follow these three steps to protect your new appliance investment:
Complete and mail
your Consumer
After completing this
Read your “Use and Care
Guide” carefully. It will
help you operate your
new appliance properly.
If you have questions, or
need more information
in the USA, call the
registration, write your
model and serial numbers
in this guide. You will need
this information should
you require service. The
service number in the
USA: 800.444.1845. In
Canada: 1.888.880.3030.
Product Ownership
Registration today.
Have the peace of mind
of knowing we can
contact you in the
unlikely event of a
GE Answer Center
®
1
safety modification.
2
3
800.626.2000. In Canada
call 1.888.880.3030
Important: To ensure that your product is registered, mail the separate product registration card.
If the separate product registration card is missing, fold and mail the form below. No envelope is needed.
FOLD HERE
Consumer Product Ownership Registration
Product
Model
Serial
Built-In Refrigerator
Mr. l Ms. l Mrs. l Miss l
First
Name
Last
Name
Street
Address
Apt. #
Zip
Code
City
State
Date Placed
In Use
Month
Phone
Number
Day
Year
Monogram®
General Electric Company
Louisville, KY 40225
✄
TAPE CLOSED
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty for customers in Canada
Built - In Refrigerators
YOUR MONOGRAM REFRIGERATOR WARRANTY
Staple sales slip or cancelled check here. Proof of original purchase
date is needed to obtain service under warranty.
WHAT IS
COVERED
From the Date
of the Original
Purchase
FULL TWO-YEAR WARRANTY
For two years from date of original purchase, we will provide, free of charge, parts and
service labor in your home to repair or replace any part of the refrigerator that fails because
of a manufacturing defect.
FULL FIVE-YEAR WARRANTY
For five years from date of original purchase, we will provide, free of charge, parts and
service labor in your home to repair or replace any part of the sealed refrigerating system (the
compressor, condenser, evaporator and all connecting tubing) that fails because of a
manufacturing defect.
LIMITED ADDITIONAL SEVEN-YEAR WARRANTY ON THE SEALED SYSTEM
For the sixth through twelfth year from date of original purchase, we will provide, free
of charge, replacement parts for any part of the sealed refrigerating system (the compressor,
condenser, evaporator and all connecting tubing) that fails because of a manufacturing
defect. You pay for the service trip to your home and for service labor charges.
This warranty is extended to the original purchaser and any succeeding owner for products
purchased for ordinary home use in Canada.
All warranty service will be provided by our Factory Service Centers or by our authorized
Customer Care® servicers during normal working hours.
Should your appliance need service, during warranty period or beyond, call 1.888.880.3030.
• Service trips to your home to teach you how
• Failure of the product if it is used for
other than its intended purpose or used
commercially.
WHAT IS NOT
COVERED
to use the product.
Read your Use and Care material.
• Improper installation.
If you then have any questions about
operating the product, please contact your
dealer or our Consumer Relations office at
the address below, or call, toll free:
If you have an installation problem, contact
your dealer or installer. You are responsible
for providing adequate electrical, plumbing
and other connecting facilities.
1.888.880.3030
• Replacement of house fuses or resetting of
circuit breakers.
WARRANTOR IS NOT RESPONSIBLE FOR
CONSEQUENTIAL DAMAGES.
• Damage to the product caused by accident,
fire, floods or acts of God.
Some provinces do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary from province to province.
To know what your legal rights are in your province, consult your local or provincial consumer
affairs office.
Warrantor: Camco Inc. If further help is needed concerning this warranty, write: Manager,
Consumer Relations, Camco Inc., 1 Factory Lane, Suite 310, Moncton, N.B. E1C 9M3.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty for customers in the USA
Built - In Refrigerators
YOUR MONOGRAM REFRIGERATOR WARRANTY
Staple sales slip or cancelled check here. Proof of original
purchase date is needed to obtain service under warranty.
FULL TWO-YEAR WARRANTY
WHAT IS
For two years from date of original purchase, we will provide, free of charge, parts and
service labor in your home to repair or replace any part of the refrigerator that fails because
of a manufacturing defect.
COVERED
From the Date
of the Original
Purchase
FULL FIVE-YEAR WARRANTY
For five years from date of original purchase, we will provide, free of charge, parts and
service labor in your home to repair or replace any part of the sealed refrigerating system (the
compressor, condenser, evaporator and all connecting tubing) that fails because of a
manufacturing defect.
LIMITED ADDITIONAL SEVEN-YEAR WARRANTY ON THE SEALED SYSTEM
For the sixth through twelfth year from date of original purchase, we will provide, free
of charge, replacement parts for any part of the sealed refrigerating system (the compressor,
condenser, evaporator and all connecting tubing) that fails because of a manufacturing
defect. You pay for the service trip to your home and for service labor charges.
This warranty is extended to the original purchaser and any succeeding owner for products
purchased for ordinary home use in the 48 mainland states, Hawaii and Washington, D.C.
In Alaska the warranty is the same except that it is LIMITED because you must pay to ship
the product to the service shop or for the service technician’s travel costs to your home.
All warranty service will be provided by our Factory Service Centers or by our authorized
Customer Care® servicers during normal working hours.
Should your appliance need service, during warranty period or beyond, in the U.S.A. call
800.444.1845. In Canada: 888.880.3030.
• Service trips to your home to teach you
• Damage to the product caused by accident,
WHAT IS NOT
COVERED
how to use the product.
fire, floods or acts of God.
Read your Use and Care material.
• Failure of the product if it is used for
other than its intended purpose or used
commercially.
If you then have any questions about
operating the product, please contact your
dealer or our Consumer Affairs office at
the address below, or call, toll free:
• Improper installation.
If you have an installation problem, contact
your dealer or installer. You are responsible
for providing adequate electrical, plumbing
and other connecting facilities.
GE Answer Center®
800.626.2000
consumer information service
• Replacement of house fuses or resetting of • Loss of food due to spoilage.
circuit breakers.
WARRANTOR IS NOT RESPONSIBLE
FOR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary from state to state.
To know what your legal rights are in your state, consult your local or state consumer affairs
office or your state’s Attorney General.
Warrantor: General Electric Company. If further help is needed concerning this warranty,
write: Manager—Consumer Affairs, GE Appliances, Louisville, KY 40225
Part No. 162D3947P006
Pub No. 49-60037-1
Monogram®
General Electric Company
Louisville, KY 40225
70757
1-00 JR
Printed in the United States
Download from Www.Somanuals.com. All Manuals Search And Download.
|