Installation
Instructions
Built-In Dishwashers
ZBD6400, ZBD6500, ZBD6600
ZBD6700, ZBD6900, ZBD7000,
ZBD7100
Chef’s Washers
ZBD6605, ZBD6905, ZBD7005,
ZBD7105
Design Guide with
Installation Instructions
®
Monogram.
We bring good things to life.
Download from Www.Somanuals.com. All Manuals Search And Download.
Design Information
PRODUCT DIMENSIONS
ADVANCE PLANNING
• These dishwashers are designed for versatility,
adaptable to virtually any installation.
• All models have a full length door or a modified
door to accept a full cabinet panel without the
traditional access panel
• Side tub flange trim is adjustable and will conceal
any slight gap between the dishwasher and adjacent
cabinetry.
34"
Adjustable
to 35"
*Dishwasher model
ZBD7000 and
Chef’s Washer
model ZBD7005
require a 3/4" thick
custom panel and
will be 24-3/4"
deep.
• These dishwashers may be installed beneath
countertops of stone or other materials that will not
accept screws. No trim kit required.
*24"
23-7/8"
Standard installation in 24" deep cabinets
• In standard 24" deep cabinets, the dishwasher door
will be flush with adjacent cabinetry.
• Models with 3/4" thick custom door panel will fit
flush with adjacent cabinetry.
DISHWASHER MODELS
Traditional Built-In
ZBD6400 BB, Black - Accepts 1/4" or 3/4" custom
panels
ZBD6400 WW White - Accepts 1/4" or 3/4" custom
panels
Trim Kits for models ZBD6400
• ZPF625W (white) or ZPF625B (black) custom panel
kits, supports a 1/4" thick custom door panel.
• ZPF675W (white) or ZPF675B (black) custom panel
kits support a 3/4" thick custom door panel.
Traditional Built-In
ZBD6500 SS, Stainless steel door
Professional Series
ZBD6600 SS, Stainless Steel
Fully Wrapped
ZBD6700 BB, Black
Supplied or Custom Toekicks
• A 2-piece toekick is supplied with all models. The
toekick is height and depth adjustable.
• Depending on cabinetry style, a custom toekick can
also be installed to match cabinetry. Care must be
taken to assure door swing clearance above the
toekick.
• A notched continuous toekick may be necessary to
allow a long door panel, on models ZBD7000 and
ZBD7005, to swing back and under the dishwasher.
ADA-Compliant
Installation below 34" high countertops
A reduced height installation (32-1/2" min.) beneath
a 34" countertop, can be accomplished by removing
the front leveling legs. The rear legs should be
screwed in flush with the bottom support, as shipped.
The front of the dishwasher must be shimmed to
level the dishwasher. Water and electrical must be
routed through the back wall.
ZBD6700 WW, White
ZBD6900 SS, Stainless steel with black controls
Fully Integrated
ZBD7000 II, Requires custom panel and handle
ZBD7100 SS, Stainless steel with tubular handle
• All models are ADA-Compliant. Models ZBD7000
and ZBD7005 offer even more installation and
design flexibility because the required custom door
panel may be sized from 26-1/4 to 30-1/4" height.
See page 9 for details.
CHEF’S WASHER MODELS
Professional Series
ZBD6605 SS, Stainless steel
Fully Wrapped
ZBD6905 SS, Stainless steel
Fully Integrated
ZBD7005 II, Requires custom panel and handle
ZBD7105 SS, Stainless steel with tubular handle
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
MATERIALS YOU WILL NEED:
Materials Required for All Installations
¨ 90° Elbow (3/8”NPT external thread on one end, opposite
end sized to fit water supply)
Screw Type Clamps
90° Elbow
Note: Use new ferrule. Do not use old parts.
¨ Strain relief for electrical connection
¨ Thread seal tape
¨ UL Listed wire connectors (3)
¨ Screw type hose clamps
Strain Relief
Wire Nuts
Thread Seal
Tape
Materials For New Installations Only:
¨ Air gap for drain hose, if required
¨ Waste tee for house plumbing, if applicable
¨ Electrical cable or power cord, if applicable
¨ Hand shut-off valve (recommended)
Shut-Off
Valve
Electrical Cable
or Power Cord
Waste Tee
¨ Water line 3/8” min. copper or 1/2” min. plastic (plastic
must be tested for temperature and pressure)
¨ Coupler for extending drain line, if applicable
Coupler
Air
Gap
Hot Water Line
Flat Blade Screwdriver
TOOLS YOU WILL NEED:
Nut Driver
Tools Required for All Installations
¨ Phillips head and flat blade screwdrivers
¨ 3/8”, 5/16” and 1/4” nutdrivers
¨ Level
Phillips Head
Screwdriver
Tubing
Cutter
Safety Glasses
¨ Carpenters square
¨ Measuring tape
¨ Safety glasses
¨ Flashlight
¨ Bucket to catch water when flushing the line
¨ Tubing cutter
Flashlight
Wire Strippers
Adjustable
Wrench
Bucket
¨ Gloves to protect against sharp edges
¨ Wire strippers
Drill
and Bits
For New Installations Only:
¨ Drill and appropriate bits
¨ Hole saw set
Measuring Tape
Square
Hole
Saw Set
Level
Gloves
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
PARTS SUPPLIED:
Remove the hardware accessory bag and other parts
from inside or taped to the outside of the dishwasher.
Check contents against illustrations to insure that all
parts are included.
Template
for
ZBD7000
ZBD7005
Only
¨ 2-piece toekick
¨ 6 screws (see illustration)
Junction
Box Cover
with screws
¨ 2 leveling legs
¨ Template for the installation of a
custom panel packed with models
ZBD7000 and ZBD7005 only
¨ Junction box cover
2 Leveling Legs
Template with Mounting Hardware
Insulation
Screws C
Screws A
(2) Countertop
Mounting
Screws B
(2) Cabinet
Mounting
Screws
(2) Color
Matched
Toekick
2-Piece Toekick with
Sound Insulation
Screws
Screws
PREPARE DISHWASHER ENCLOSURE
• The floor inside the opening must be even and level
with the finished floor of the kitchen. If the kitchen
floor is tile, it may be
higher than the floor of
the installation cutout.
This Wall Area
must be Free of
Pipes or Wires
34" to 35"
Underside
of Countertop
to Floor
24"
Min.
1-3/4"
Pieces of wood may be
placed into the cutout
floor to make it level or
higher than the room
6"
20-1/2"
floor. This will allow easy
removal for any future
service.
23-7/8" Min.
24-1/4" Max
*Models ZBD7000 and ZBD7005 with custom panels are 24-3/4" deep
Corner Installation
• When installing into a
corner, allow 2" min.
clearance between
dishwasher and adjacent
cabinet or wall.
• Allow 24-1/8" min.
clearance from the front
of the dishwasher for door
opening.
• The rough cabinet opening must be at least 24” deep,
23-7/8”min. to 24-1/4” wide. The height should be 34”
min. and 35” max.
Countertop
Dishwasher
Note: ADA installation, beneath 34" high countertops may be accom-
plished by removing front leveling legs. Drain hose, water and
electrical must be routed through the cutout on the back of the
dishwasher.
24-1/8"
• The dishwasher must be installed so that drain hose is
no more than 10 feet in length for proper drainage.
• The dishwasher must be fully enclosed on the top, sides
and back, but should not support any part of the
enclosure.
Clearance for Door
Opening 2" Minimum
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
DRAIN REQUIREMENTS
• Follow local codes and ordinances.
• Do not exceed 10 feet distance to drain.
• To prevent back flow into the dishwasher, connect
drain line to an air gap or use a 30” high drain loop,
depending on local codes.
Method 1 – Air Gap with Waste Tee or Disposer
An air gap must be used when the waste tee or disposer
connection is less than 18” from the floor.
• Air gap must be used when waste tee or disposer
connection is less than 18” above the floor to prevent
siphoning.
DETERMINE DRAIN METHOD
The type of drain installation depends on the following
questions.
■ Do local codes or ordinances require an air gap?
■ Will waste tee or disposer connection be less than 18”
above the floor?
Method 2 – High Drain Loop with Waste Tee or
Disposer Install waste tee or disposer and air gap according
to manufacturer’s instructions.
■ Will installation have a high drain loop less than 30”
above the floor?
If the answer to ANY of these questions is YES, Method 1
MUST be used.
30"
Min.
30"
Min.
18"
Min.
12"
Min.
• If all answers are NO, either method may be used.
CABINET PREPARATION
• Drill a 1-1/2” dia. hole in the cabinet wall within
the shaded areas shown for the drain hose connec-
tion. The hole should be smooth with no sharp
edges.
An air gap MUST BE USED if the drain hose is con-
nected to a waste tee or disposer lower than 18” above
the floor level.
• Failure to provide the proper drain connection using
an air gap or a 30” min. high drain loop will result in
improper draining of the dishwasher which may cause
damage or poor wash performance.
PRUDENCE
Il DOIT Y AVOIR une coupure antirefoulement si le
tuyau de vidange est branché sur un raccord d’égout ou
un broyeur d’ordures à moins de 46 cm (18 po) du sol.
• Si la vidange n’est pas branchée correctement en
utilisant une coupure antirefoulement ou un boucle
d’égout d’au moins 76 cm (30 po) de haut,
l’écoulement de l’eau du lave-vaisselle n’est pas bon,
ce qui peut causer des dommages ou un mauvais
lavage de la vaisselle.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
PREPARE ELECTRICAL WIRING
FOR PERSONAL SAFETY: Remove
house fuse or open circuit breaker
before beginning installation. Do not use
an extension cord or adapter plug with
this appliance.
Alternate
Receptacle
Location
18"
1-1/2" Dia. Hole (Max.)
Receptacle
Location
Area
18"
6"
3"
6"
AVERTISSEMENT
from
POUR ASSURER LA SÉCURITÉ
2"
Cabinet
PERSONNELLE, il faut enlever le fusible
ou couper le courant au disjoncteur
avant de commencer l’installation. Avec
cet appareil, il ne faut pas utiliser de
rallonge ni d’adaptateur de prise.
2"
24"
from Wall
Ground
Black
White
Electrical Connections to Dishwasher:
Electrical Requirements
The dishwasher junction box is located on the right side
at the front of the dishwasher. The electrical cable must
extend forward at least 24” to reach the junction box
when dishwasher is installed.
• The wiring may enter the opening from either side,
rear or the floor within the shaded area.
• Cut a 1-1/2” max. dia. hole to admit the electrical
cable or use the same hole cut for the drain hose. The
hole must be free of sharp edges. If the cabinet wall is
metal, the hole edge must be covered with a bushing.
• For power cord connections, install a 3-prong ground-
ing type receptacle in the sink cabinet rear wall, 6"
min, or 18" max. from the opening, and 6" to 18"
above the floor.
• This appliance must be supplied with 120V, 60 Hz., and
connected to an individual properly grounded branch
circuit, protected by a 15 or 20 ampere circuit breaker or
time delay fuse.
• Wiring must be 2 wire with ground and rated for 75°C
(176°F).
• If the electrical supply does not meet the above require-
ments, call a licensed electrician before proceeding.
Grounding Instructions–Cable Direct
This appliance must be connected to a grounded metal
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and be
connected to the equipment-grounding terminal or lead
on the appliance.
Grounding Instructions–Power Cord
This appliance must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk
of electrical shock by providing a path of least resistance
for electric current. The plug must be plugged into an
appropriate outlet that is installed and grounded in
accordance with all local codes and ordinances.
AVERTISSEMENT
The improper connection of the equip-
ment-grounding conductor can result in
a risk of electric shock. Check with a
qualified electrician or service represen-
tative if you are in doubt that the appli-
ance is properly grounded.
Le mauvais branchement du fil de mise à
la terre de l’équipement peut causer un
choc électrique. En cas de doute sur la
mise à la terre de l’appareil, consulter un
électricien qualifié ou un représentant
technique.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
PREPARE HOT WATER LINE
The line may enter from either side, rear or floor
within the shaded area shown.
• The water line may pass through the same hole as
the electrical cable and drain hose. Or, cut an
additional 1-1/2" dia. hole to admit the line. If a
power cord with plug is used, it must pass through
a separate hole.
Right Side Entry
Approx. 40"
from Wall
1-1/2"
Dia.
Hole
Shut-off Valve
Hot
1-3/4"
6"
Water Line Connection
• Turn off the water supply.
• Install a hand shut-off valve in an accessible loca-
tion, such as under the sink. (Optional, but strongly
recommended and may be required by local codes.)
• The hot water line should be 3/8” O.D. copper
tubing or 1/2” O.D. plastic tubing. The line must
extend forward at least 30" from the left side or 40"
from the rear wall.
• The water line must be long enough to form a
smooth natural loop with no sharp bends or kinks
between the cutout entry.
Left
Side Entry
Approx. 30"
from Wall
Cabinet Face
2" from Floor
• Adjust water heater to deliver temperatures of 120°F to
150°F.
• Flush water line to clean out debris.
• The hot water supply line pressure must be 20-120 PSI.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Panel Dimensions
CUSTOM PANEL FOR MODELS
CUSTOM PANEL FOR MODELS
ZBD7000 AND ZBD7005
ZBD6400 ONLY
Panel kits must be ordered separately. Installation
of any custom panel should be completed before
the dishwasher is installed.
These models require a field installed 3/4" thick custom
panel and custom handle. An installation template is
packed with these models and may be obtained in
advance. Order Pub. No. 31-5912. See page 15 for panel
installation instructions.
1/4" PANEL WITH ZPF625 TRIM KIT
Custom
Countertop
Panel Size
1/4" Thick
Door Panel
Cabinets
Side
View
25-5/16"
1/4"
Radius
Cut
A
Floor
B
23-1/8"
3/4" Max.
Bottom of
Adjacent Cabinetry
• Cut the panel to the dimensions shown.
• The bottom left and right corners should be cut at
1/4" radius. See illustration.
STEP A: Determine custom panel height
1. Measure dimension A, from the underside of the
countertop to the bottom of adjacent cabinets.
2. Subtract 1/4". This allows a 1/4" clearance gap
between the underside of the countertop and the top
of the dishwasher door.
3/4" PANEL WITH ZPF675 TRIM KIT
The custom panel size varies depending on your
installation.
HEIGHT = A – 1/4"
Note: 26-1/4" minimum panel height is required to cover the door
frame. Panel height varies depending on installation. Consideration
must be given to door swing clearance above the toekick.
Custom
Panel Size
Countertop
Cabinets
Top
STEP B: Determine custom panel width
1. Measure dimension B, the rough opening width.
2. Subtract 1/4" for clearance (1/8" on each side).
WIDTH = B – 1/4"
3/4" Thick
Door Panel
*Height
A
Floor
Note: 23-1/8" minimum panel width is required to cover the door
frame.
23-1/8"
3/4" Max.
Bottom of
Adjacent Cabinetry
Toekick Installation
These dishwashers are supplied with a standard toekick.
However, a notched continuous toekick is recommended
to prevent door swing interference and to maintain
toekick alignment with adjacent cabinets. See page 14
for details.
* Height is equal to A minus 5-1/4" plus 1/4"
EXAMPLE: A = 30-1/2" minus 5-1/4", plus 1/4" is equal to 25-1/2".
1. Measure Dimension A, from underside of countertop
to bottom of adjacent cabinets.
2. Subtract 5-1/4”. Control panel height is 5". Allow
1/4" clearance between countertop and control
panel.
3. Add 1/4". The custom panel slides up, behind
control panel.
ADA Installations Beneath 34" Countertops
Use the same methods shown here to calculate door
panel height. A notched continuous toekick will help to
prevent door swing interference and maintain toekick
alignment with adjacent cabinets.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
STEP 3 REMOVE ACCESS COVER
BEFORE YOU BEGIN:
CUSTOM PANEL INSTALLATION: If you intend to
install custom door panels, (on some models) refer to
trim kit installation instructions. Custom panels should
be in place before installing the dishwasher.
Insulation Board
STEP 1 REMOVE PACKAGING
Cut the shipping carton and use it as a pad beneath the
dishwasher. This will protect the finished floor in the
kitchen.
Junction Box
Access Cover
• Remove wrapping and uncoil the drain hose in the
back of the dishwasher. Do not remove rear insulation
blanket.
• Lay the dishwasher on it’s back. Do not kink or crush
the drain hose.
• Remove sound insulation board and the access cover
plate.
• Install UL listed strain relief on junction box.
STEP 2 INSTALL LEVELING LEGS
1-1/4" Min.
STEP 4 INSTALL 90° ELBOW
Remove
Red Plugs
Unscrew
Rear Legs to
Rear
Installation
Insulation
Height
Blanket
90°
• Measure installation opening from the floor to the
bottom of the countertop.
Elbow
Thread
Seal Tape
• Install the front leveling legs into holes on the brack-
ets. Use a wrench to screw the legs in until the overall
height of the dishwasher is 1/4" less than the installa-
tion opening height.
Note: Install the legs as shown, 1-1/4" min from the
bottom of the bracket.
• Install the 90° elbow onto the water inlet. Use thread
seal tape or pipe thread compound. Thread seal tape
should be wrapped in same direction as the threads on
the elbow.
• Remove and discard the red plugs from the front
holes.
• The 90° elbow should face the inlet water line.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
STEP 5 INSTALL POWER CORD
SKIP THIS STEP IF DISHWASHER
WILL BE DIRECT WIRED
STEP 7 SLIDE DISHWASHER
INTO OPENING
DO NOT PUSH AGAINST THE FRONT PANEL WITH
KNEES, DAMAGE WILL OCCUR!
• Insert drain hose into the cabinet wall hole. If a power
cord is used, guide the end through a separate hole.
• Maximum power cord length is 6 ft.
• The power cord and connections must comply with
the National Electrical Code, Section 422 and/or
local codes and ordinances.
Insert power cord wires
through strain relief and
tighten.
Ground
White
Black
• Position water supply line and house wiring on the
floor of the opening to avoid interference with base
of dishwasher.
• Strip 1/2" insulation
from ends of power
• Slide dishwasher into the opening a few inches at a
time. As you proceed, pull the drain hose through the
cabinet wall under the sink.
• Check to be sure there is no interference with
waterline or house wiring.
cord wires.
• Connect incoming power cord white to dishwasher
white, black to black and ground to dishwasher green
wire. Use UL listed wire connectors of appropriate size.
• Install junction box cover with screws provided. Be sure
wires are not pinched under the cover.
• Again, check to be sure the dishwasher is level.
STEP 6 LEVEL DISHWASHER
• Carefully, upright the dishwasher, be careful not to
bend the leveling legs.
• Check to be sure the dishwasher is level and is
adjusted to fit the installation cutout height.
STEP 8 CONNECT WATER LINE
NOTE: If you are using an existing water line, cut 1" off
the end. Always use a new ferrule and compression nut.
• The water supply line should be flushed to clear any
foreign material before connecting to the dishwasher.
• Make sure there are no sharp bends or kinks to restrict
water flow.
Level
Top
• Insert water line into the 90° elbow.
and
• Slide ferrule against
elbow and secure with
compression nut.
• Replace access panel
plate.
Sides
Compression Nut
Ferrule
Hot Water
Supply Line
90° Elbow
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
STEP 9 CONNECT DRAIN LINE
STEP 10 CONNECT ELECTRICAL
FOLLOW ALL LOCAL CODES AND ORDINANCES.
FOR DIRECT WIRE ONLY
(If a power cord with plug is used, plug it into the wall
outlet and continue with next step.)
• The dishwasher is supplied with a 72" long drain hose.
• If a longer drain hose is required, add up to 48” of
length for a total of 10 ft. length.
• Secure the drain hose to the air gap, waste tee or
disposer with clamps.
Verify that power is
turned off at the
source.
• Make sure drain hose is not kinked.
Ground
Insert power cord wires
through strain relief and
tighten.
IMPORTANT: When connecting
drain line to disposer, check to be
sure that drain plug has been
removed. DISHWASHER WILL
NOT DRAIN IF PLUG IS LEFT
IN PLACE.
Remove
Plug
White
Black
Method 1 – Air gap with waste tee or disposer
• Locate the three dishwasher wires, (white, black and
green) with stripped ends. Insert wire through the
small hole in the junction box. Use wire connectors to
connect incoming ground to green, white to white and
black to black.
• Install junction box cover with screws provided. Check
to be sure that wires are not pinched under the cover.
• Reinstall Insulation Board in position. The board
should be secured so it does not interfere with door
opening.
Waste Tee Installation
Disposer Installation
Method 2 – High drain loop with waste tee or disposer
Waste Tee Installation
Fasten to underside
of countertop
Fasten to underside
of countertop
If house wiring is not 2-wire with
ground, a ground must be provided
by the installer. When house wiring is
aluminum, be sure to use UL Listed
anti-oxidant compound and alumi-
num-to-copper connectors.
30"
30"
12"
Min.
12"
Min.
Min.
Min.
Disposer Installation
Waste Tee Installation
AVERTISSEMENT
Si l’installation électrique de la maison
n’est pas à deux fils plus terre,
l’installateur doit installer un fil de
mise à la terre. Si l’installation
électrique de la maison est en alu-
minium, il faut prendre soin d’utiliser
des composés antioxydants et des
connecteurs aluminium à cuivre sur la liste UL.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
STEP 11 POSITION AND LEVEL THE DISHWASHER
• Check to be sure the dishwasher is adjusted to correct
Door Rub Door Rub
height and is centered in the cutout.
• Open and close the door to insure proper operation of
the door. If there is any binding or rubbing, readjust
leveling legs.
On Right On Left
Hand Side Hand Side
Adjust
This
Leg
Adjust
This
Leg
Use a wrench to make adjustments.
• If the door rubs on the right side of the cabinet, extend the left rear
leg by unscrewing it one quarter turn.
C
C
• If the door rubs against the left side of the cabinet, extend the right
rear leg by unscrewing it one quarter turn.
• Check level again. Repeat the procedure if necessary.
STEP 12 PRE-TEST CHECK LIST
¨ Verify water supply and drain lines are not kinked or in contact
with other components.
Installation service calls are not covered by your
warranty. To avoid unnecessary charges, review
this list carefully.
¨ Turn on the sink hot water faucet and verify water temperature.
Incoming water temperature must be between 120°F and 150°F.
120°F min. temperature is required for best wash performance.
¨ Turn on water supply.
¨ Check to be sure power is OFF.
¨ Open the door and remove all foam and paper packaging.
¨ Pull lower rack out, about half way. Check to be sure it does
not roll back or forwards on the door. If the rack moves,
adjust leveling legs.
¨ Open the door. Check to be sure Insulation Board does not
interfere with door opening.
CHECK WATER FILL LEVEL
STEP 13 DISHWASHER WET TEST
¨ Turn on power supply.
For best performance, check the water fill level.
Run through a complete RINSE ONLY cycle to ensure it is emptying
and filling correctly. For low water pressure situations run the
RINSE ONLY cycle 3 times. Half-way through the final RINSE ONLY
cycle, pause the dishwasher and check the water level inside the
dishwasher. If the water level is not above the minimum water level
(marked on the lower spray support tower), increase the fill level.
1. Ensure the dishwasher is not running through a cycle. Depress
the WATER TEMP button for 10 seconds until the second buzzer
sounds (except on ZBD6600).
¨ Select the normal cycle and press the start button.
¨ The control will indicate a slow/no fill by flashing the CHINA
CRYSTAL, LIGHT WASH OR WASH CYCLE light. Check water
supply, then adjust fill time according to the chart shown.
¨ Check to be sure that water enters the dishwasher, wait up to
2 minutes. If water does not enter the dishwasher, check to be
sure that water is turned on.
¨ Check for leaks under the dishwasher. If a leak is found, turn
power and water off, then tighten connections. Restore power
and water supply.
¨ Check for leaks around the door. A leak around the door could be
caused by door rubbing or hitting against adjacent cabinetry.
Reposition the dishwasher if necessary.
¨ After the dishwasher drains check drain lines. If leaks are found,
turn power off, correct as necessary.
2. Press the START/CANCEL button to select fill time, as per chart
(65 seconds is the factory setting).
3. To test time, press DELAY START. The dishwasher will start filling.
Listen for the dishwasher to complete filling. Once filled, the fill
level must be checked to ensure fill time is correct.
4. Once complete, press the WATER TEMP button to exit fill time
mode.
Continue to press the START/CANCEL button
until the desired indicator is illuminated.
Cycle Statue Indicators Fill Time
SENSING
WASHING
RINSING
DRYING
CLEAN
¨ The control will indicate a slow/no drain by flashing the RINSE
ONLY, SANI WASH or HEAT OPTIONS. Check that the airgap is
clear of debris and that the knockout in the disposer or waste tee
is fully removed. Check that the drain hose is not kinked.
¨ Open the dishwasher door and make sure that most of the water
has drained. If not, check that disposer plug has been removed
and that air gap is not plugged.
60 seconds
65 seconds
70 seconds
80 seconds
90 seconds
¨ Cancel the dishwasher cycle and complete the installation.
¨ Remove protective film if present from the control panel and door.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
STEP 14 SECURE DISHWASHER
STEP 15 INSTALL TOEKICK
• Loosen depth
adjustment screws
inside the
TO CABINET AND
COUNTERTOP
To maintain position and alignment, the dishwasher
must be secured to the countertop and adjacent
cabinets.
Adjust to
Toekick
Depth
bracket.
• Slide bracket out
to proper depth.
Tighten screws.
• Attach supplied
toekick to
Secure dishwasher to countertop:
• Drill pilot holes through the mounting bracket and
into the underside of the countertop. Secure with
screws A provided.
brackets with
screws C provided.
Do not tighten.
• Adjust the toekick
to touch the floor.
Screw A
Attachment Screws
Tighten screws.
Adjust to Touch Floor
INSTALL A
CONTINUOUS
CUSTOM
TOEKICK
Notch the continuous
toekick to allow the door
panel to swing under the
dishwasher.
IMPORTANT: To avoid damage to your dishwasher,
drive screws straight and flush. Protruding screw heads
may scratch the top of the escutcheon or door and can
interfere with door closing.
A continuous custom toekick is recommended for
models with long custom door panels.
Secure dishwasher to adjacent cabinets:
• Remove plastic plugs button on the inside of the
dishwasher frame. One on each side.
• Drill pilot holes through the dishwasher holes and
into the adjacent cabinets. Install screws B provided.
• Replace plastic plug buttons.
• Cut a notch in the toekick deep enough to allow the
door to swing freely under the dishwasher.
• Check for interference by slowly opening and closing
the door. If the door touches the toekick, trim to
prevent interference.
• Secure the toekick to adjacent cabinets in such a
manner that it may be removed if service is required.
STEP 16 ADJUST SIDE TRIM STRIPS
Adjust Side Trim
to Meet Cabinetry
• Open the door fully.
• Loosen (but do not
Plug Buttons
remove) screws holding
Screw B
the top and side trims.
• Adjust trim to cover
opening gap. Tighten
screws.
Loosen
Screws
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Panel Installation for Models ZBD7000 and ZBD7005
The custom panel should be prepared by your
STEP 4 INSTALL CUSTOM HANDLE
cabinet manufacturer according to the instructions
shown on page 9. Use the supplied installation
template to locate the mounting screws for the
door.
Screws Must
Be Countersunk
Into Panel
4-1/2" Max.
From Top
of Panel
STEP 1 DRAW
CENTERLINE
Handle
Custom
Door Panel
• Place the custom panel on a
flat surface with appearance
side down.
A custom handle must be installed onto the panel
before the panel is secured to the dishwasher door.
• The handle should be installed so that it aligns with
adjacent drawer handles, or 4-1/2" max. from the top
of the panel. Secure the handle in the same manner as
cabinet handles.
• Locate the vertical center of
the panel at the top.
• Use a carpenters square to
draw a centerline from top
to bottom.
STEP 5 INSTALL PANEL
STEP 2 ALIGN TEMPLATE
TO PANEL
• Secure the panel to the door by inserting the top and
bottom shoulder washers into the matching keyhole
slots.
• Trim template on the
dotted line along all sides.
• Place the template on the
panel aligned with the top
edge and the centerline.
Use tape to hold in place.
• Use an awl to mark the
screw hole locations indicated on the template.
• Remove the template.
• Make sure all 4 washers engage the keyhole slots.
• Press the panel against the door and push downwards
until the washers are fully engaged into the key hole
slots. The panel should align evenly with the top and
Mark Center
Screw Holes
sides.
Custom
Panel
Dishwasher
Door
Shoulder Washers
Engage Keyhole
Slots
STEP 3 INSTALL MOUNTING
SCREWS AND WASHERS
If the panel is less than 3/4" thick, shorter screws must
be used. Use #8 x 3/8" screws for 1/2" thick panels.
• Use a 3/32" drill bit to drill pilot holes 3/32" deep in
the marked locations.
Note: The custom panel is secured to the dishwasher
door with the shoulder washers and screws provided.
The washer will slip into the keyhole slots on the dish-
washer door.
Shoulder
Washer
Screw
• Stand the dishwasher
upright.
• Open dishwasher door
and drive the supplied
#6 x 2 Phillips screws
through the inner door
and into the custom
panel. Drive one screw
• Place shoulder washer over one hole and drive the
supplied #8 x 1/2 Phillips pan head wood screws into
the panel.
• Install remaining washers and screws in the marked
locations.
at the top and one on
each side as shown.
Custom
Panel
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: While performing installations described in this book,
safety glasses or goggles should be worn.
TM
For Monogram local service in your area, call
1-800-444-1845.
Note: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
0616 400 327
Pub. No. 49-5905
Dwg. No. 165D4700P231
®
Monogram.
(N.D. 131) 11/01
General Electric Company
Louisville, KY 40225
Download from Www.Somanuals.com. All Manuals Search And Download.
|