Installation
Instructions
Wine Chiller,
Wine Reserve
and
Beverage Center
Design Guide
With Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Design Guide
THE INSTALLATION SPACE
PRODUCT CLEARANCES
The wine chiller, wine reserve and beverage center is
factory set for a 110° door swing.
Locate
Outlet
When installed in a corner:
• Allow 4″ min. clearance on the hinge side for the
90° door swing and to allow racks to slide out.
• Allow 10″ minimum clearance on the hinge side
10-1/2"
24"
9" Max.
34-1/2"-35"
for a full 110° door swing.
1-1/2"
23-3/4" Min.
90° Door Swing
23-3/4"
10" Minimum
to Wall
21-5/8"
NOTE:
Handle and
34-1/2"
handle standoff
depth is 1-3/4″
23-5/8"
90°
23-3/4"
4" Minimum
The cutout depth should be 24″
110°
to Wall
The cutout dimensions shown allow for a full door
swing and access to the pull-out racks when installed
as a built-in in standard 24″ deep cabinets.
• The wine chiller, wine reserve and beverage center
can be installed freestanding.
• The door swing is reversible on all models. If
desired, change the door swing before installation.
Choose the location:
• These products may be closed in on the top and
three sides as long as the front is unobstructed for
air circulation and proper access to the door.
• Do not install these products where the temperature
will go below 55°F (13°C) or above 90°F (32°C).
• Do not install where it will be subject to direct
sunlight, heat or moisture.
• If installing between frameless cabinets, a 1/2″ wide
filler strip or side panel may be needed on hinge
side. The filler strip will act as a spacer between the
case and adjacent cabinet door swing. The width
of the opening must include the filler panels.
NOTE: The door should protrude 1″ beyond the
surrounding cabinets.
• These products are not designed to be stacked one
over the other.
Additional Specifications
• A 120 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install a
properly grounded 3-prong electrical receptacle
recessed into the back wall as shown. Electrical must
be located on rear wall as shown. NOTE: GFI
(ground fault interrupter) is not recommended.
Black or Stainless Steel Toekick Options
• These products are shipped with a black toekick
installed. An optional stainless steel toekick is also
supplied with each product. For shipping purposes,
the stainless steel toekick is secured to the back
of the unit.
SIDE-BY-SIDE INSTALLATIONS
Increase storage capacity by installing two Monogram
beverage centers, wine chillers or wine reserves together.
Or, for a complete refreshment center, install any two
of these units together.
• A side-by-side installation requires at least a 47-1/2″
wide opening. No trim kits required.
Locate
Outlet
10-1/2"
10-1/2"
24"
14"
34-1/2"-35"
9" 9"
15"
1-1/2"
• Products must operate from separate, properly
grounded receptacles.
47-1/2" Min.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
TOOLS REQUIRED
STAINING WOOD DRAWER FRONTS
• #2 Phillips screwdriver
• Adjustable wrench
The drawer fronts are unfinished cherry wood.
During use, oil from hands may accumulate and stain
the wood.
• The drawer fronts may be stained and sealed to
match adjacent cabinetry. The tinted glass will
make the stained wood appear darker. A true color
match can be seen only when the door is opened.
• Apply the stain and sealer according to the
manufacturer’s instructions. To avoid unpleasant
odor, keep the door open to ventilate and allow
the stain/sealer to dry completely before using
the product.
PARTS SUPPLIED
• Monogram nameplate
• Hardware for changing door swing
• Optional stainless steel toekick with screws
and spacers
• Left and right side hinge covers
• Top screw hole cover
GROUNDING THE WINE CHILLER,
WINE RESERVE AND BEVERAGE
CENTER
STEP 1 REMOVE PACKAGING
• Remove corner blocks and foam drawer stops.
• Remove all packing material, tape and protective
plastic coverings.
• Remove stainless steel toekick taped to the back
of the unit.
IMPORTANT –
FOR PERSONAL SAFETY, THIS APPLIANCE MUST
BE PROPERLY GROUNDED.
Please read carefully.
The power cord of this appliance is equipped with a
three-prong (grounding) plug which mates with a
standard three-prong (grounding) wall receptacle to
minimize the possibility of electric shock hazard from
this appliance.
CAUTION:
Small objects are a choke
hazard for children. Remove and discard any parts
not used.
MISE EN GARDE :
Les petits
objets peuvent étrangler les enfants. Il faut jeter
Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
toutes les piéces qui ne sont pas utilisées.
Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grounded 3-prong
wall outlet.
DO NOT, UNDER ANY
CIRCUMSTANCES, CUT
OR REMOVE THE THIRD
(GROUND) PRONG
FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT
THE REFRIGERATOR TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS
APPLIANCE.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
STEP 2 REVERSE DOOR SWING
SKIP THIS STEP IF DOOR SWING SUITS THE
INSTALLATION
Install
3 Hinge
Screws
Parts Included:
• Top left case hinge
Remove
Top Hinge
• Bottom left case hinge
• Left and right side decorative hinge cover
• Decorative hinge screw hole cover
• Torx® driver bit
Hinge
Pin and
Bracket
Tools Required:
• Phillips screwdriver
• Electric drill
Door Stop
and Cam Riser
Remove the door:
• Flatten the shipping carton to use as a pad.
• Remove the 2 screws and the toekick. Set aside the
screws and toekick for final installation.
• Use the supplied Torx® bit and electric drill to
remove the 3 screws holding the top case hinge.
Lift off the hinge. (Screws will be used to install the
new hinge.)
Remove
Hinge
• Lift the door off the bottom case hinge.
• Remove the bottom case hinge pin and bracket.
Apply Monogram Nameplate:
• Install the Monogram nameplate. See instructions
and template on back cover.
Rotate the door:
The handle will be on the right side of the door;
hinges will be installed on the left side of the case.
• Remove the door stop and cam riser on the original
bottom right side of the door.
• Remove the fill plug on the top right side
of the door.
Install Toekick
The toekick has a
cutout on the
left and right
sides.
Remove
the plug
• Turn the door over and reinstall the fill plug on the
new left side.
Move Fill
on the left
side and
Plug to
Reinstall the door:
• Install the original door stop and cam riser onto
the bottom left side of the door.
Right Side
reinstall on
the right
side. If you
choose to install
• Install the new supplied bottom case hinge pin and
bracket onto bottom left side.
the stainless steel toekick,
• Place the door onto the bottom case hinge.
• Install the supplied left-hand top case hinge with
the 3 original screws.
• Select the hinge cover marked with an “L”.
• Peel backing off the tape inside the decorative
reinstall the plug on the right side of that toekick.
• Install original screws and spacers or screws and
spacers supplied with the stainless steel toekick.
Install screws through the spacer standoff, toekick
and into the base as shown.
hinge cover.
• Press and snap the hinge
Install Covers
cover into place.
• Snap the screw hole cover into
place on the opposite side.
IMPORTANT:
Check to be sure screws are tight and that the door
is straight and does not sag. The door should swing
freely.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
STEP 3 LEVEL
STEP 5 SLIDE PRODUCT INTO
THE CUTOUT
• Use an adjustable wrench to turn the leveling legs
and raise or lower the product.
• Carefully, slide the unit into the opening.
Be careful not to entangle power cord.
• Make certain that the door protrudes 1″ beyond
the surrounding cabinets.
• Adjust carefully; the product should be level and
plumb with cabinetry, and should align with adjacent
toekick height.
• Check again to be sure the unit is level.
STEP 6 INSTALL NAMEPLATE
• Follow instructions on the back page for installation
of the Monogram nameplate.
STEP 7 SET TEMPERATURE
CONTROLS
Turn Right to Lower
Turn Left to Raise
• The temperature controls are preset. Refer to
the Owner’s Manual for more information.
Allow 24 hours for temperature to stabilize.
If you skipped Step 2:
• Select the hinge cover marked “R” or “L”, depending
on door swing.
• Peel backing off the tape inside the decorative
hinge cover. Press and snap into position.
• Snap the screw hole cover into place on the
opposite side.
STEP 4 CONNECT POWER
• Connect power cord plug to a properly grounded
receptacle.
• Check to make sure power is on by opening the door
to see if interior light turns on.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TEMPLATE FOR NAMEPLATE LOCATION
Cut on Dotted Line
Upper Left
Upper Right
Corner of
Glass if Hinge
is on Right
Top of Glass Door
Corner of
Glass if Hinge
is on Left
Top of Badge
Door Frame Side
Door Frame Side
DOOR NAMEPLATE LOCATION
To position nameplate:
• Cut template along dotted line.
• Hold or tape template behind
glass door so that it is visible from
the front side.
• Remove backing from nameplate.
• Place nameplate onto front side of
door, matching illustration on the
template.
IMPORTANT: Nameplate must
be placed on the opposite side of
the door handle.
Note: While performing installations described in this book,
safety glasses or goggles should be worn.
For Monogram® local service in your area, call
1.800.444.1845.
Note: Product improvement is a continuing endeavor at
General Electric. Therefore, materials, appearance and
specifications are subject to change without notice.
Pub. No. 49-60210-4
Dwg. No. 197D5129P001
03-04 JR
Printed in Slovenia
Download from Www.Somanuals.com. All Manuals Search And Download.
|