ge.com
Safety Instructions . . . . . . . . .2, 3
Owner’s Manual and
Installation Instructions
Operating Instructions . . . . . .4, 5
Additional Controls . . . . . . . . . . .5
Controls . . . . . . . . . . . . . . . . . . . .4
Normal Operating Sounds . . . . .5
AEE18
Care and Cleaning
Air Filter . . . . . . . . . . . . . . . . . . .6
Grille and Case . . . . . . . . . . . . . .6
Grille Frame Removal . . . . . . . . .6
Outdoor Coils . . . . . . . . . . . . . . .6
Installation Instructions
Through-the-Wall
Installation—Optional . . . . . . . .13
Window Installation . . . . . . . .8–12
Troubleshooting Tips . . . . . . .14
Consumer Support
Consumer Support . . . . . . . . . .16
Warranty . . . . . . . . . . . . . . . . . .15
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on a label on the
side of the air conditioner.
49-7570 02-07 JR
Download from Www.Somanuals.com. All Manuals Search And Download.
ge.com
WARNING!
EXTENSION CORDS—115-Volt models only
Because of potential safety hazards under certain
CAUTION:
conditions, we strongly recommend against the
use of an extension cord.
DO NOT use an extension cord with any of the
230/208 volt models.
However, if you must use an extension cord,
it is absolutely necessary that it be a UL-listed,
14 gauge, 3-wire grounding type appliance
extension cord having a grounding type plug
and outlet and that the electrical rating of the
cord be 15 amperes (minimum) and 125 volts.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
About the controls on the air conditioner.
Features and appearance will vary.
TEMP CONTROL
MODE CONTROL
Controls
Temp Control
Mode Control
The temp control is used to maintain the
room temperature. The compressor will
cycle on and off to keep the room at the
same level of comfort. Turn the knob
clockwise to Cooler (blue) and the indoor
air will become cooler. Turn the knob
counterclockwise to Warmer (red) and
the indoor air will become warmer.
Hi Cool and Low Cool provide cooling with
different fan speeds.
Hi Heat and Low Heat provide heating with
different fan speeds.
Fan Only setting provides air circulation and
filtering without cooling or heating.
NOTE: If you move the mode control from a
cool setting to Off, a fan setting or a heat
setting, wait at least 3 minutes before switching
back to a cool setting.
Cooling Descriptions
For Normal Cooling—Select Hi Cool or
Low Cool with the temp control at midpoint.
For Maximum Cooling—Select Hi Cool with
the temp control turned clockwise as far as
possible.
For Quieter & Nighttime Cooling—Select
Low Cool with the temp control at midpoint.
Heating Descriptions
For Normal Heating—Select Hi Heat or
Low Heat with the temp control at midpoint.
For Maximum Heating—Select Hi Heat with
the temp control turned counterclockwise as
far as possible.
For Quieter & Nighttime Heating—Select
Low Heat with the temp control at midpoint.
Circulaire
For continuous
side-to-side air
circulation, set
the Circulaire
switch to On.
For fixed side-to-side air direction, set the
Circulaire switch to On until the desired air
direction is obtained, then move it to Off.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional controls.
ge.com
Vent Control
The vent control is located above the control
panels.
When set at CLOSE, only the air inside the room
will be circulated and conditioned. When set at
OPEN, some outside air is let into the room.
To open the vent, push the lever to the right.
To close it, push it to the left.
Air Direction—Up and Down
Fingertip pressure on the horizontal louvers
adjusts the air direction up or down.
Control Panel Door
Press to open and close the door.
Normal operating sounds.
ꢀ You may hear a pinging noise caused by
water being picked up and thrown against the
condenser on rainy days or when the humidity
is high. This design feature helps remove
moisture and improve efficiency.
ꢀ Water will collect in the base pan during
high humidity or on rainy days. The water may
overflow and drip from the outdoor side of
the unit.
ꢀ The fan may run even when the compressor
ꢀ You may hear the thermostat click when the
does not.
compressor cycles on and off.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and cleaning of the air conditioner.
Grille and Case
Turn the air conditioner off and remove the
plug from the wall outlet before cleaning.
To clean, use water and a mild detergent.
Do not use bleach or abrasives.
Outdoor Coils
The coils on the outdoor side of the air conditioner
should be checked regularly. If they are clogged
with dirt or soot, they may be professionally cleaned.
Air Filter
The air filter behind the front grille should be
checked and cleaned at least every 30 days or
more often if necessary.
To remove:
Open the inlet grille upward by pulling out the
bottom of the inlet grille.
1
Using the tab, pull up slightly on the filter
to release it and pull it down.
2
Clean the filter with warm, soapy water. Rinse and
let the filter dry before replacing it. Do not clean
the filter in a dishwasher.
CAUTION:
DO NOT operate the air
conditioner without a filter because dirt and lint will clog it
and reduce performance.
Grille Frame Removal (if necessary for coil cleaning)
Remove the air filter. See the Air Filter section above.
If present, remove the grille frame attachment screw.
Grasp the lower corners of the grille frame while
pressing in on the case side tabs with your finger
tips. Pull out to release and lift it up.
NOTE: Do not pull the bottom edge toward you more than 3″
or you may damage the tabs of the grille.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Instructions
Air Conditioner
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
BEFORE YOU BEGIN
CAUTION:
Do not, under any circumstances, cut or
remove the third (ground) prong from the
power cord.
Read these instructions completely
and carefully.
Do not change the plug on the power cord
of this air conditioner.
•
IMPORTANT — Save these
instructions for local inspector’s use.
Aluminum house wiring may present special
problems—consult a qualified electrician.
•
IMPORTANT — Observe all
governing codes and ordinances.
• Note to Installer – Be sure to leave these
TOOLS YOU WILL NEED
instructions with the Consumer.
• Note to Consumer – Keep these
instructions for future reference.
• Skill level – Installation of this appliance
requires basic mechanical skills.
Phillips head screwdriver
• Completion time – Approximately 1 hour
• We recommend that two people install
this product.
• Proper installation is the responsibility
Adjustable wrench
Flat-blade screwdriver
Ruler or tape measure
Scissors or knife
of the installer.
• Product failure due to improper installation
is not covered under the Warranty.
• You MUST use all supplied parts and use
proper installation procedures as described
in these instructions when installing this
air conditioner.
Pencil
Level
ELECTRICAL REQUIREMENTS
Power cord includes a current interrupter
The 3-prong grounding plug minimizes the
possibility of electric shock hazard. If the wall
outlet you plan to use is only a 2-prong outlet,
it is your responsibility to have it replaced with
a properly grounded 3-prong wall outlet.
device. A test and reset button is provided on
the plug case. The device should be tested on a
periodic basis by first pressing the TEST button
and then the RESET button. If the TEST button
does not trip or if the RESET button will not stay
engaged, discontinue use of the air conditioner
and contact a qualified service technician.
Some models require 230/208-volt a.c.,
protected with a time delay fuse or circuit
breaker. These models should be installed
on their own single branch circuit for
best performance and to prevent
overloading house or apartment wiring
circuits, which could cause a possible
fire hazard from overheating wires.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Window Installation Instructions
PARTS INCLUDED
Window
sash seal
(Appearance may vary)
Left
accordion
panel
Foam top
window gasket
Top
mounting
rail
Right
accordion
panel
V-support (2)
Window locking
bracket (2)
Bolt (2) & nuts (2)
Type A (6)
Type B (4)
Type C (6)
Type D (6)
Type E (4)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Window Installation Instructions
1
3
WINDOW REQUIREMENTS
• These instructions are for a standard
double-hung window. You will need to
modify them for other types of windows.
REMOVE THE AIR CONDITIONER
FROM THE CASE
Remove the inlet grille.
A
• All supporting parts must be secured
to firm wood, masonry or metal.
• The electrical outlet must be within
reach of the power cord.
Remove the filter.
B
C
D
18″ min.
30″ to 41″
(With accordion panels)
Remove the painted screws from each side
and the screw in the front. Save to reinstall
later.
2
STORM WINDOW REQUIREMENTS
A storm window frame will not allow the
air conditioner to tilt toward the outside,
and will keep it from draining properly.
To adjust for this, attach a piece of wood
to the stool.
Screw
WOOD PIECES–
Screw
WIDTH: 2″
Screw
LENGTH: Long enough to fit inside the
Grasp the lower corners of the grille frame
window frame.
while pressing in on the case side tabs with
your finger tips. Pull out to release and lift
it up.
THICKNESS: To determine the thickness,
place a piece of wood on the stool to
make it 1/2″ higher than the top of the
storm window frame or the vinyl frame.
Attach securely with nails or screws
provided by the installer.
NOTE: Do not pull the bottom edge toward
you more than 3″ or you may damage the
tabs of the grille.
1/2″ higher
than vinyl frame
(on some windows)
Wood
1/2″ higher
than storm
window
Stool
frame
Storm window
frame
Vinyl frame
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Window Installation Instructions
PREPARE THE CASE
Install the top mounting rail with 4 type B
screws from the inside of the case.
Press firmly to drive the screws into the
gasket and through the top mounting rail.
3 REMOVE THE AIR CONDITIONER
FROM THE CASE (cont.)
5
A
Remove the locking screw and locking
E
bracket from the lower frame. Save to
reinstall later.
Remove the ground screw and save to
reinstall later.
Top mounting rail
F
Insert the frames for the accordion panels
into the top mounting rail and the bottom
frame guides. Attach the accordion panels
to the side of the case using 3 type A screws
on each side.
B
Remove the ground screw
and save to reinstall later
NOTE: When attaching the accordion panels,
make sure to only screw the inner panels
to the case sides.
Slide the air conditioner from the case by
G
gripping the base pan handle and pulling
Top mounting rail
forward while bracing the case.
Type A
screws
BACK
Bottom mounting rail
4
PREPARE THE WINDOW
Cut the window sash seal to the proper
length. Peel off the backing and attach the
seal to the underside of the window sash.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Window Installation Instructions
6
6
INSTALL THE CASE
IN THE WINDOW
INSTALL THE CASE
IN THE WINDOW (cont.)
Carefully slide the case into the window and
center the case. Lower the window behind
the top mounting rail. Pull the bottom of the
case forward so that the bottom mounting
rail is tight against the back of the window
stool. Mount the case to the window sill using
4 type E screws. Drill pilot holes, if necessary.
Extend the left and right accordion panels
to the vertical window sashes. Drill pilot
holes and attach the top and bottom
corners with 4 type D screws.
A
F
Top mounting rail
Type D
screw
Type D
screw
4 type E screws
Type D
screw
Type D
screw
Stool
7
INSTALL SUPPORT BRACKETS
AND THE FOAM TOP WINDOW
GASKET
Make sure the bolts
B
C
Drill pilot holes and attach the support
brackets with two type D screws, one on
each side.
and nuts are all of the
A
way in both the left
and right V-supports.
Bolt and nut
Position the V-supports
on the case bottom so that
they will be near the outside
wall. Attach a V-support to
each side of the bottom of
the case using type C
V-support
screws, 3 on each side.
Use a wood block (obtained
locally) between the leveling
bolts and the wall if the wall
is weak or if the weight of the
air conditioner falls between
the studs in the wall.
D
E
Cut the foam top window gasket to the
window width.
B
C
Stuff the foam between the glass and the
window to prevent air and insects from
getting into the room.
Adjust the leveling
bolts and nuts against
the outside wall so
that the case has a
slight tilt to the outside.
Tighten nuts with an
adjustable wrench. Use
a level; no more than a
1/2 bubble will be the correct case slant to the
outside.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Window Installation Instructions
8
8
INSTALL THE AIR CONDITIONER
IN THE CASE
INSTALL THE AIR CONDITIONER
IN THE CASE (cont.)
Make sure the ground
wire is off to the side
and slide the air
conditioner into the
case. Do not push
on the controls or the
finned coils. Make
sure the air
Press the grille frame in around the power
cord on the right side. Secure the grille with
the painted screws on each side and the
screw in the front that were removed
earlier.
A
E
Screw
conditioner is
firmly seated.
Screw
Reinstall the locking bracket and screw
removed earlier.
B
C
Screw
Reinstall the filter.
F
Reconnect the ground wire to the air
conditioner using the screw removed earlier.
IMPORTANT: The ground wire must be
reinstalled to ensure a proper ground.
Reinstall the inlet grille. Connect power.
G
Reattach the front grille frame to the case
by inserting the tabs on the grille frame into
the slots on the front top of the case.
D
Caulk or weather-strip any gaps or openings
to the outside to seal the installation.
Guide the lever carefully
through the grille frame
as you push it in.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Through-the-Wall Installation Instructions—Optional
The case may be installed through-the-wall
in both existing and new construction.
1
IMPORTANT (cont.)
Secure with 14 wood screws anchored at
least an inch into the wall support structure.
D
Read completely, then follow step-by-step.
NOTE: Except for the V-support
assemblies (included), obtain all materials
locally for mounting the air conditioner
through-the-wall.
NOTE: Drill pilot holes, if necessary, for
proper installation. If the frame is oversized,
use shims to prevent case distortion.
Install the V-supports. See the INSTALL
THE CASE IN THE WINDOW section in the
Window Installation Instructions.
E
1
IMPORTANT
Through-the-wall installation is not
appropriate if any of the side or top louvers
in the case will be obstructed by the wall.
2
FINISH THE WALL OPENING
Caulk all four sides on the outdoor side of
the case to prevent moisture from getting
through to the interior wall. Use of flashing
(drip rail) will further prevent water from
dripping inside the wall and down the
outside of the building.
A
All side and top louvers in the case must
project on the outdoor side of the wall.
The room side of the case must project
into the room far enough to maximize the
balance of the unit.
The case must be installed level from side-
to-side and with a slight tilt from front to
rear. Use a level; no more than a 1/2 bubble
will be the correct case slant to the outside.
Plaster line
Lintel angle
Lintel angle is required to support bricks or
blocks above opening.
Trim molding
(if desired)
Caulking
Flashing is required and should extend the
length of the opening to ensure no inside
cavity leakage occurs.
OUTSIDE
INSIDE
Air louvers
(top and
sides must
project on the
outdoor side
of the wall)
Remove the air conditioner from the case.
For specific instruction, refer to the Window
Installation Instructions.
A
B
Bottom rail
Make certain that a wall receptacle is
available close to the hole location or make
arrangements to install a receptacle.
Wood filler and
caulking (above
and below the
flashing)
V-supports
Case
bottom
Bottom
rail
Flashing
(Drip rail)
Flashing
(Drip rail)
Place the case in the wall opening and
place wood support strips between the case
bottom and the flashing on both sides of the
bottom rail. They should be the same height
as the bottom rail and the same length as
the wall opening.
C
Wood support strips
Place the air conditioner into the case.
For specific instruction, refer to the Window
Installation Instructions.
B
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…Review the chart below first and you may not need to call for service.
Problem
Possible Causes
What To Do
Air conditioner
does not start
The air conditioner
is unplugged
• Make sure the air conditioner plug is pushed completely
into the outlet.
The fuse is blown/circuit
breaker is tripped
• Check the house fuse/circuit breaker box and replace
the fuse or reset the breaker.
Power failure
• The unit will automatically re-start in the settings last
used after the power is restored.
• There is a protective time delay (approximately
3 minutes) to prevent tripping of the compressor
overload. For this reason, the unit may not start
normal cooling or heating for 3 minutes after it
is turned back on.
The current interrupter
device is tripped
• Press the RESET button located on the power cord plug.
• If the RESET button will not stay engaged, discontinue
use of the air conditioner and contact a qualified service
technician.
Air conditioner
freezing up
Ice blocks the air flow
and stops the air conditioner
from cooling the room
• Set the mode control at Fan Only or Hi Cool with the
temp control at a warmer setting.
Air conditioner does not
cool as it should
Airflow is restricted
• Make sure there are no curtains, blinds or furniture
blocking the front of the air conditioner.
The temp control may
not be set correctly
• Turn the temperature knob clockwise as far as possible.
The air filter is dirty
• Clean the filter at least every 30 days. See the Operating
Instructions section.
The room may have been hot
Cold air is escaping
• When the air conditioner is first turned on you need
to allow time for the room to cool down.
• Check for open furnace floor registers and
cold air returns.
• Set the air conditioner’s vent to the closed position.
• See “Air conditioner freezing up” above.
Cooling coils have iced up
Airflow is restricted
Air conditioner does not
warm as it should
• Make sure there are no curtains, blinds or furniture
blocking the front of the air conditioner.
The temp control may
not be set low enough
• Turn the knob counterclockwise as far as possible.
The lowest setting provides maximum warming.
The air filter is dirty
• Clean the filter at least every 30 days. See the Operating
Instructions section.
The room may have been cold
Warm air is escaping
• When the air conditioner is first turned on, you need to
allow time for the room to warm up.
• Check for open furnace floor registers and
cold air returns.
Water drips outside
Water drips indoors
Excessively hot and
humid weather
• This is normal.
The air conditioner is not
tilted to the outside
• For proper water disposal, make sure the air conditioner
slants slightly from the case front to the rear.
Water collects in
base pan
Moisture is removed from
indoor air and drains into
rear of a cabinet where a fan
blows it against the outdoor
condenser coil
• This is normal for a short period in areas with
little humidity; normal for a longer period in very
humid areas.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
GE Air Conditioner Warranty.
All warranty service provided by our Factory Service Centers,
Staple your receipt here.
Proof of the original purchase
date is needed to obtain service
under the warranty.
®
or an authorized Customer Care technician. To schedule service,
on-line, 24 hours a day, visit us at ge.com, or call 800.GE.CARES
(800.432.2737). Have serial number and model number available
when calling for service.
For The Period Of: GE Will Replace:
One Year
From the date of the
original purchase
Any part of the air conditioner which fails due to a defect in materials or workmanship.
During this limited one-year warranty, GE will also provide, free of charge, all labor and related
service to replace the defective part.
What Is Not Covered:
ꢀService trips to your home to teach you how to
use the product.
ꢀReplacement of house fuses or resetting of circuit
breakers.
ꢀImproper installation, delivery or maintenance. If you
have an installation problem, or if the air conditioner
is of improper cooling capacity for the intended use,
contact your dealer or installer. You are responsible
for providing adequate electrical connecting facilities.
ꢀFailure due to corrosion on models not corrosion-
protected.
ꢀDamage to the product caused by improper power supply
voltage, accident, fire, floods or acts of God.
ꢀIncidental or consequential damage caused by possible
defects with this air conditioner.
ꢀFailure of the product resulting from modifications to
the product or due to unreasonable use including failure
to provide reasonable and necessary maintenance.
ꢀDamage caused after delivery.
ꢀIn commercial locations, labor necessary to move the
unit to a location where it is accessible for service
by an individual technician.
EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in this
Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a
particular purpose, are limited to one year or the shortest period allowed by law.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home
use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. Louisville, KY 40225
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Support.
GE Appliances Website
ge.com
ge.com
ge.com
Have a question or need assistance with your appliance? Try the GE Appliances Website 24 hours a day,
any day of the year! For greater convenience and faster service, you can now download Owner’s Manuals,
order parts or even schedule service on-line.
Schedule Service
Expert GE repair service is only one step away from your door. Get on-line and schedule your service at
your convenience 24 hours any day of the year! Or call 800.GE.CARES (800.432.2737) during normal
business hours.
Real Life Design Studio
GE supports the Universal Design concept—products, services and environments that can be used by
people of all ages, sizes and capabilities. We recognize the need to design for a wide range of physical and
mental abilities and impairments. For details of GE’s Universal Design applications, including kitchen
design ideas for people with disabilities, check out our Website today. For the hearing impaired, please call
800.TDD.GEAC (800.833.4322).
Extended Warranties
ge.com
Purchase a GE extended warranty and learn about special discounts that are available while your warranty
is still in effect. You can purchase it on-line anytime, or call 800.626.2224 during normal business hours.
GE Consumer Home Services will still be there after your warranty expires.
Parts and Accessories
ge.com
Individuals qualified to service their own appliances can have parts or accessories sent directly to their
homes (VISA, MasterCard and Discover cards are accepted). Order on-line today, 24 hours every day
or by phone at 800.626.2002 during normal business hours.
Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally
should be referred to qualified service personnel. Caution must be exercised, since improper servicing may cause
unsafe operation.
Contact Us
ge.com
If you are not satisfied with the service you receive from GE, contact us on our Website with all the details
including your phone number, or write to: General Manager, Customer Relations
GE Appliances, Appliance Park
Louisville, KY 40225
Register Your Appliance
ge.com
Register your new appliance on-line—at your convenience! Timely product registration will allow for
enhanced communication and prompt service under the terms of your warranty, should the need arise.
You may also mail in the pre-printed registration card included in the packing material.
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|