|
GE Monogram®
Installation
Instructions
Beverage Center
Model
ZDB24 WW
ZDB24 BB
Wine Chiller
Model
ZDW24 WW
ZDW24 BB
Download from Www.Somanuals.com. All Manuals Search And Download.
Design Information
Beverage Center & Wine Chiller
ZDB24 WW
White Beverage Center
The Monogram beverage center or the wine
chiller adds an eloquent statement of style,
convenience and flexibility.
Models
Available
ZDB24 BB
Black Beverage Center
The Monogram beverage center and wine
chiller can be used freestanding or as a
built-in.
ZDW24 WW
White Wine Chiller
ZDW24 BB
Black Wine Chiller
Front ventilation allows the beverage center
or wine chillder to be installed as a built-in
and still operate efficiently.
Dimensions
& Clearances
Locate
Outlet
24" Min.
The bottom front grille area must remain
unobstructed for proper air circulation and
operation.
34-1/2"-35"
5"
24" Min.
Cutout dimensions shown allow for a full door
swing and access to the pull-out racks.
34-1/2"
24-1/8"
23-7/8"
Increase storage capacity by installing two
Monogram beverage centers side by side or
two Monogram wine chillers side by side.
Or, install a Monogram beverage center next
to a Monogram wine chiller for a complete
refreshment center.
Installation
Options
A side by side installation requires a 48" wide
opening. No trim kits required.
•The glass door fronts should align evenly
with adjacent cabinet door fronts.
Frameless Cabinets:
• If installing between frameless cabinets, a
1/2" wide filler strip or side panel may be
required. The filler strip will act as a spacer
between the door case and adjacent cabinet
and will prevent interference with cabinet
door swing. The width of the opening must
include filler panels.
Provide two separate properly grounded
electrical outlets for a side by side installation.
Each electrical outlet should have a voltage
rating that matches the rating plate.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
Beverage Center & Wine Chiller
IMPORTANT - (Please read carefully)
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
Grounding
the
Beverage Center
or Wine Chiller
FOR PERSONAL SAFETY, THIS APPLIANCE properly grounded.
MUST BE PROPERLY GROUNDED.
Where a standard 2-prong wall outlet is encoun-
The power cord of this appliance is equipped tered, it is your personal responsibility and
with a three-prong (grounding) plug which
mates with a standard
obligation to have it replaced with a properly
grounded 3-prong wall outlet.
three-prong (grounding)
wall receptacle to minimize
the possibility of electric
shock hazard from this
appliance.
DO NOT, UNDER ANY CIRCUMSTANCES,
CUT OR REMOVE THE THIRD (GROUND)
PRONG FROM THE POWER CORD.
Use of Adapter plug
When disconnecting the power cord from the
adapter, always hold the adapter in place with
one hand and pulling the power cord with the
other hand. If this is not done, the adapter
ground terminal is very likely to break with
repeated use.
Because of potential hazards under certain
conditions, we strongly recommend against
use of an adapter plug. However, if you still
elect to use an adapter, where local codes
permit, a TEMPORARY CONNECTION, may
be made to a properly grounded 2-prong wall
outlet by use of a UL listed adapter available
at most hardware stores.
Should the adapter ground terminal break, DO
NOT USE the appliance until a proper ground
has again been established.
Align Large Prongs/Slots
Use of Extension Cords
Because of potential safety hazards under
certain conditions, we strongly recommend
against the use of an extension cord. However,
if you still elect to use an extension cord, it is
absolutely necessary that it be a UL listed 3-wire
grounding type appliance extension cord
Ensure Proper Grounding and Firm
Connection Exists Before Use
The larger slot in the adapter must be aligned having a grounding type plug and outlet and
with the larger slot in the wall outlet to
provide proper polarity in the connection of
the power cord.
that the electrical rating of the cord be 15
amperes (minimum) and 120 volts.
Use of an adapter plug will increase the
cutout depth required.
PRUDENCE
CAUTION
Brancher la borne de terre d’un adaptateur
sur la vis du couvercle de la prise murale ne
met pas l’appareil à la terre, sauf si la vis du
couvercle est métallique, n’est pas isolée et
si la prise murale est mise à la terre par
l’intermédiaire des fils de la maison. Il faut
faire vérifier le circuit par un électricien
qualifié pour s’assurer que la prise est
correctement mise à la terre.
Attaching the adapter ground terminal to a
wall outlet cover screw does not ground the
appliance unless the cover screw is metal,
and not insulated, and the wall outlet is
grounded through the house wiring. You
should have the circuit checked by a
qualified electrician to make sure the
outlet is properly grounded.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Preparation
Beverage Center & Wine Chiller
To remove the door:
•Remove the top hinge pin using a 1/8" Allen
wrench. Set aside.
Reverse
Door
Slip Shim
Behind Hinge
•Lift the door off the bottom hinge.
•Remove the top hinge and set aside.
•Remove the bottom hinge, the plastic washer
and the bottom hinge pin using a Phillips
screwdriver.
Swing
Top Hinge
•Install the Phillips hinge pin in the top
hinge and re-install the top hinge on the
bottom left side.
• Re-install the plastic washer over the hinge
pin.
• Install the Allen wrench hinge pin in the
bottom hinge and re-install the bottom
hinge on the top left side.
• Insert the supplied plug buttons into the old
hinge holes, top and bottom.
Bottom Hinge
The light trigger on the bottom of the door
must be removed and secured to the opposite
end.
•Remove the light trigger by backing out 2
screws. Set the trigger and screws aside.
•Install screws from plastic bag packed with
Owner’s Manual into light trigger holes.
•Turn the door upside down.
Light Trigger
Top of the Door
3/4"
11/16"
12-1/4"
•Measure and mark 12-1/4" and 13" from the
right side (or 3/4" from the first location).
Measure and mark 11/16" from the front
side of the door. See illustration.
Front of the Door
•Drill holes with 5/32" drill bit.
•Install the light trigger with original screws.
•Remove the top hinge pin using the 1/8"
allen wrench.
•Place the door onto the bottom hinge, and
install the top hinge pin with allen wrench.
•Open and close door to test door swing. If
door drags and does not close evenly, loosen
hinge screws and slip shims behind the
hinge. Tighten screws and test again.
Upper Left
Corner of
Glass
Top of Name Plate
Top of Glass Door
DOOR
NAME PLA
TE
LOCA
TION
Door Frame Side
P/N 41005263
Position new nameplate:
•Remove the original nameplate, now located
on the bottom of the door.
•Locate the template on the back of this
instruction book.
•Hold or tape template behind glass door.
•Remove backing from Monogram name-
plate.
•Place nameplate onto front side of door,
matching illustration on template.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Beverage Center & Wine Chiller
Remove all packing material and tape.
B.
C.
Step
Tools and materials required:
1
Remove the
Packaging
Parts List:
D.
F.
E.
G.
H.
I.
A.
CAUTION: Small objects are a choke
hazard to children. Remove and
discard any parts not used.
J.
PRUDENCE – Les petits objets
peuvent étrangler les enfants. Il faut
jeter toutes les pièces qui ne sont pas
utilisées.
K
Note: Consider door swing direction. If you wish to change door
swing, complete the instructions shown on page 5 before installing
the handle.
Step
2
Install
Handle
• Place handle standoff against the top screw hole
in the door. Position the standoff so that the
small screw hole points toward the floor.
•Drive screw through the standoff and into the
door. Do not tighten.
•Install bottom standoff. Do not tighten.
•Place handle to standoffs so that handle mount-
ing posts are inserted into the standoffs. The
handle should fit into the curved shape of the
standoff. Again, the set screw hole should be
pointing downwards.
•Remove the handle and tighten standoffs to
door.
Screw
Allen Wrench
•Place handle to standoffs and install set screws
through the bottom of standoffs using the allen
wrench provided.
•The handle should be tight against the standoff.
•Save the allen wrench for future use.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Beverage Center & Wine Chiller
•Tilt the unit slightly to one side to access the
bottom corner holes.
•Install a U-Clip into the front and rear holes
on the bottom as shown.
CAUTION: See illustration. Be sure the tangs
on the clips are on the outside and the
straight portion is inserted into the holes.
•Screw the leveling legs into the U-clips all
the way until snug. Then, adjust the leveling
legs to installation height.
A.
Step
3
Install
Leveling
Legs
B.
•Follow the same procedure for the opposite
side.
C.
D.
•Move the beverage center/wine chiller close
to the opening.
•Connect the power cord plug to the properly
grounded receptacle.
•Slide the unit into the opening.
Step
4
Slide the
Unit into
the Cutout
heck
kist
Sunheck
C
C
Monogram
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Template
Beverage Center & Wine Chiller
Template For Nameplate Location
To be used when door swing has been reversed,
with handle on right side, hinge on left side.
To position new nameplate:
•Remove the original nameplate, now located on
Upper Left
Corner of
Glass
Top of Name Plate
Top of Glass Door
the bottom of the door.
DOOR
NAME PLA
TE
TION
LOCA
•Cut template along dotted line.
•Hold or tape template behind glass door in the
upper left corner so that it is visible from the
front side.
Door Frame Side
P/N 41005263
•Remove backing from Monogram nameplate.
•Place nameplate onto front side of door,
matching illustration on template.
Cut on Dotted Line
Upper Left
Corner of
Glass
Top of Glass Door
Top of Name Plate
DOOR
NAME PLATE
LOCATION
Door Frame Side
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
For Monogram local service in your area, call
1-800-444-1845.
Pub. No. 49-60148
Part No. 197D4432P001
(N.D. 204) 6/01
NOTE: Product improvement is a continuing endeavor at General
Electric. Therefore, materials, appearance and specifications are
subject to change without notice.
®
Monogram.
41006773 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|