®
GE Monogram
Owner’s Manual
ZDI15 and ZDIS15
Automatic Icemaker
monogram.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Immediately contact the dealer (or builder)
that sold you the icemaker.
If you
received a
damaged
icemaker
If you
need
service
For customers in Canada:
To obtain service, see the Consumer Services
page in the back of this manual.
FIRST, contact the people who serviced your
appliance. Explain why you are not pleased.
In most cases, this will solve the problem.
We’re proud of our service and want you to be
pleased. If for some reason you are not happy
with the service you receive, follow these steps.
NEXT, if you are still not pleased, write all the
details---including your phone number---to:
For customers in the USA:
FIRST, contact the people who serviced your
appliance. Explain why you are not pleased.
In most cases, this will solve the problem.
Manager, Customer Relations
Camco Inc.
1 Factory Lane, Suite 310
Moncton, N.B. E1C 9M3
NEXT, if you are still not pleased, write all the
details---including your phone number---to:
Manager, Customer Relations
GE Appliances
Appliance Park
Louisville, KY 40225
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
Before it is used, the icemaker must be
properly installed and located as described in
this manual.
• Unplug the icemaker or disconnect power
before cleaning, servicing or changing the
light bulb. Failure to do so can result in
death or electrical shock.
WARNING–To reduce the risk of fire,
electrical shock or injury when using your
icemaker, follow basic precautions including
the following:
• It is your responsibility to be sure your
icemaker:
– has been installed where it is protected from
the elements.
• Never allow children to operate, play with,
or crawl inside the icemaker.
– is located so that the front is not blocked to
restrict incoming or discharge air flow.
• Never clean icemaker parts with flammable
fluids. The fumes can create a fire hazard
or explosion.
– is connected only to the proper kind of
outlet, with the correct electric supply and
grounding. A 115 volt, 60 Hz., 15 amp fused
electrical supply is required.
• Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance. The fumes
can create a fire hazard or explosion.
NOTE: Time delay fuse or circuit breaker
is recommended.
– is not used by anyone unable to operate
• Be sure your icemaker is properly installed
and grounded by a qualified technician in
accordance with the Installation Instructions.
it properly.
– is used only to do what icemakers are
designed to do.
• Do not attempt to repair or replace any
part of your icemaker unless it is specifically
recommended in this manual. All other
servicing should be referred to a qualified
technician.
– is properly maintained.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
LIRE ET CONSERVER CES INSTRUCTIONS
Avant son utilisation, la machine à glaçons doit
être bien installée et située selon la description
dans ce manuel.
•
Débrancher la machine à glaçons ou déconnecter
le courant électrique avant de la nettoyer, de
l’entretenir ou de changer l’ampoule d’éclairage.
L’omission d’observer ces précautions peut
causer un décès ou un choc électrique.
AVERTISSEMENT : Pour réduire les
risques d’incendie, de choc électrique ou de
blessure lors de l’utilisation de la machine à
glaçons, suivre les précautions fondamentales,
y compris les suivantes :
•
Vous avez la responsabilité de vous assurer que
la machine à glaçons :
– a été installée où elle est protégée contre les
intempéries .
•
•
Ne jamais laisser les enfants utiliser, employer
comme jouet ou pénétrer dans la machine
à glaçons.
– est située de sorte que le devant n’est pas
obstruée pour restreindre l’arrivée ou la
sortie du courant d’air.
Ne jamais nettoyer les pièces de la machine à
glaçons avec des fluides inflammables. Les
émanations peuvent créer un risque d’incendie
ou d’explosion.
– est connectée seulement au type approprié
de prise de courant avec une alimentation
électrique correcte et une liaison à la terre.
Une alimentation électrique de 115 V, 60
Hz, et fusible de 15 A est requise.
•
Ne pas entreposer ni utiliser de l’essence ou
d’autres vapeurs et liquides inflammables dans
le voisinage de cet appareil ménager ou de tout
autre appareil. Les émanations peuvent créer un
risque d’incendie ou d’explosion.
REMARQUE : Les fusibles temporisés ou
disjoncteurs de circuit sont recommandés.
– n’est pas utilisée par quiconque ne peut
faire fonctionner l’appareil d’une manière
appropriée.
•
•
S’assurer que la machine à glaçons est bien
installée et reliée à la terre par un technicien
qualifié, et conformément aux instructions
d’installation.
– est utilisée seulement pour accomplir
ce que les machines à glaçons sont destinées
à fournir.
Ne pas essayer de réparer ou de remplacer une
pièce de votre machine à glaçons à moins de
recommandations spécifiques dans ce manuel.
Tout autre besoin de service doit être soumis à
un technicien qualifié.
– est soumise à un entretien approprié.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or
remove the third (ground) prong from the
The icemaker should always be plugged into
its own individual electrical outlet which has a
power cord. For personal safety, this appliance voltage rating that matches the rating plate.
must be properly grounded.
This provides the best performance and also
prevents overloading house wiring circuits
which could cause a fire hazard from
overheated wires.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall
outlet to minimize the possibility of electric
shock hazard from this appliance.
Never unplug your icemaker by pulling on the
power cord. Always grip plug firmly and pull
straight out from the outlet.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Repair or replace immediately all power cords
that have become frayed or otherwise
damaged. Do not use a cord that shows cracks
or abrasion damage along its length or at
either end.
Where a standard 2-prong wall outlet is
encountered, it is your personal responsibility
and obligation to have it replaced with a
properly grounded 3-prong wall outlet.
When moving the icemaker, be careful not
to roll over or damage the power cord.
RACCORDEMENT ÉLECTRIQUE
Ne coupez ni retirez en aucun cas la troisième
broche (mise à la terre) de la fiche du cordon
d’alimentation. Pour votre sécurité, cet
Cette précaution est recommandée pour
garantir un rendement optimum et éviter
une surcharge des circuits électriques de la
résidence, ce qui pourrait créer un risque
d’incendie par surschauffe des fils.
appareil doit être correctement mis à la terre.
Le cordon d’alimentation de cet appareil est
muni d’une fiche à 3 broches (mise à la terre)
qui se branche dans une prise mural ordinaire
à 3 alvéoles (mise à la terre) pour réduire au
minimum les risques du chocs électriques.
Ne débranchez jamais la machine à glaçons
en tirant le cordon d’alimentation. Saisissez
fermement la fiche du cordon et tirez droit
pour la retirer de la prise.
Faites examiner la prise de courant et le circuit Réparez ou remplacez immédiatement tout
par un électricien qualifié pour vous assurer
que la prise est correctement mise à la terre.
cordon effiloché ou endommagé. N’utilisez
pas un cordon fendillé ou présentant des
signes d’usure.
Si la prise murale est du type standard à 2
alvéoles, il vous incombe de la faire remplacer
par une prise à 3 alvéoles correctement mise
à la terre.
Lorsque vous déplacez votre machine à
glaçons du mur, faites attention de ne pas la
faire rouler sur le cordon d’alimentation afin
de ne pas l’endommager.
La machine à glaçons doit toujours être
branché dans sa propre prise de courant,
dont la tension nominale est identique
à celle indiquée sur la plaque signalétique.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
DANGER: RISK OF CHILD ENTRAPMENT
Child entrapment and suffocation are not
problems of the past. Junked or abandoned
refrigeration products are still dangerous…
even if they will sit for “just a few days.” If you
are getting rid of your old appliance, please
follow these instructions to help prevent
accidents.
Before You Throw Away Your Old
Refrigeration Product:
• Take off the doors.
• Leave the shelves in place so that children
may not easily climb inside.
DANGER! RISQUES POUR LES ENFANTS
Les enfants pris au piège ou morts d’asphyxie
sont toujours d’actualité. Les appareils de
réfrigération abandonés sont toujours
aussi dangereux, même si on n’attend que
“quelque jours” pour s’en débarasser. Si vous
ne gardez pas votre ancien appareil, veuillez
suivre les directives ci-dessous afin de
prévenir les accidents.
Avant de vous débarasser de votre vieux
appareil de réfrigération:
• Démontez les portes.
• Laissez les clayettes en place afin d’empêcher
les enfants de grimper à l’intérieur.
CFC DISPOSAL
Old refrigeration products have cooling
If you are throwing away an old refrigeration
systems that used CFCs (chlorofluorocarbons). product, make sure the CFC refrigerant is
CFCs are believed to harm stratospheric
ozone.
removed for proper disposal by a qualified
servicer. If you intentionally release this CFC
refrigerant you can be subject to fines and
imprisonment under provisions of
environmental legislation.
SE DÉBARRASSER DU CFC
Les vieux appareils de réfrigération ont un
système de refroidissement qui a utilisé les
CFC (chlorofluorocarbones). Les CFCs sont
jugés nocifs pour l’ozone stratosphérique.
Si vous débarrassez de votre viel appareil de
réfrigération, assurez-vous que le frigorigène
avec CFC soit enlevé correctement par un
technicien qualifié. Si vous libérez
intentionnellement ce frigogène avec CFC
vouz pouvez être soumis aux contraventions
et à l’emprisonnement après les stipulations
des lois sur l’environment.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
USE OF EXTENSION CORDS
Because of potential safety hazards under
certain conditions, we strongly recommend
against the use of an extension cord.
3-wire grounding type appliance extension
cord having a grounding type plug and outlet
and that the electrical rating of the cord be
15 amperes (minimum) and 120 volts.
However, if you must use an extension cord, it
is absolutely necessary that it be a UL-listed (in
the United States) or a CSA-listed (in Canada),
CORDONS PROLONGATEURS
Nous vous recommandons fortement de ne
pas utíliser de cordons prolongateurs à cause
des risques potentiels qu’ils présentent dans
certaines conditions.
absolument nécessaire qu’il s’agisse d’un
cordon à 3 fils avec mise à la terre pour
appareils électroménagers homologué UL
(aux États-Unis) ou homologué CSA (au
Canada), pourvu d’une fiche et d’une prise
mises à la terre de 15 ampères (minimum)
et de 120 volts.
Toutefois si vous décidez d’utiliser tout
de même un cordon prolongateur, il est
8
Download from Www.Somanuals.com. All Manuals Search And Download.
USE OF ADAPTER PLUGS
(Adapter plugs not permitted in Canada)
Because of potential safety hazards under certain conditions, we strongly recommend against
the use of an adapter plug.
However, if you must use an adapter, where
local codes permit, a temporary connection
may be made to a properly grounded 2-prong
wall outlet by use of a UL-listed adapter
available at most local hardware stores.
adapter ground terminal is very likely to break
with repeated use.
If the adapter ground terminal breaks, DO
NOT USE the refrigerator until a proper
ground has been established.
The larger slot in the adapter must be aligned
with the larger slot in the wall outlet to provide
proper polarity in the connection of the
power cord.
Attaching the adapter ground terminal to a
wall outlet cover screw does not ground the
appliance unless the cover screw is metal, and
not insulated, and the wall outlet is grounded
through the house wiring. You should have the
circuit checked by a qualified electrician to
make sure the outlet is properly grounded.
When disconnecting the power cord from the
adapter, always hold the adapter in place with
one hand while pulling the power cord plug
with the other hand. If this is not done, the
SAVE THESE INSTRUCTIONS
FICHE D’ADAPTATION
(Fiches d’adaptation non permises au Canada)
Nous vous recommandons fortement de ne pas utiliser une fiche d’adaptation à cause des risques potentiels
qu’elle présente dans certaines circonstances.
Toutefois, si vous décidez d’utiliser tout de
même une fiche d’adaptation, vous pouvez
effectuer un raccordement temporaire, si les
codes locaux le permettent, dans une prise
de courant à 2 alvéoles adéquatement mise
à la terre en utilisant une fiche d’adaptation
homologuée UL, en vente dans la plupart
des quincailleries.
d’alimentation de l’autre. Sinon, la borne de
mise à la terre de la fiche d’adaptation risque
de casser avec le temps.
Si la borne de mise à la terre de la fiche casse,
N’UTILISEZ PAS l’appareil tant qu’une mise
à la terre adéquate n’aura pas été rétablie.
Le fait de fixer la borne de mise à la terre de
la fiche d’adaptation à la plaque de la prise de
courant n’assure pas automatiquement la mise
à la terre de l’appareil. Il faut que la vis soit en
métal, non isolée, et que la prise de courant
soit mise à la terre par l’entremise du câblage
de résidence. Faites vérifier le circuit par un
électricien qualifié pour vous assurer que la
prise est adéquatement mise à la terre.
La fente la plus longue de la fiche doit être
alignée avec la fente la plus longue de la prise
murale afin d’assurer la polarité appropriée
pour le branchement du cordon
d’alimentation.
Lorsque vous débranchez le cordon
d’alimentation de la fiche d’adaptation,
saisissez toujours la fiche d’une main pendant
que vous tirez sur la fiche du cordon
CONSERVEZ CES DIRECTIVES
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Features
Icemaker
Remove
packaging
IMPORTANT: Do not remove any permanent
instruction labels inside your icemaker or the
Tech Sheet that is fastened behind the lower
access panel.
• Do not use sharp instruments, rubbing
alcohol, flammable fluids or abrasive
cleaners to remove tape or glue. These
products can damage the surface of your
icemaker. For more information, see the
Important Safety Instructions section.
• Remove tape and any labels from your
icemaker before using (except the model
and serial number label).
To remove any remaining tape or glue, rub
the area briskly with your thumb. Tape or glue
residue can also be easily removed by rubbing
a small amount of liquid dish soap over the
adhesive with your fingers. Wipe with warm
water and dry.
Clean before
using
After you remove all of the packaging
materials, clean the inside of your icemaker
before using it.
See the cleaning instructions in the Care and
Cleaning section.
Set controls
1. To start the normal ice making cycle,
NOTE: The CLEAN setting is used whenever
solutions are circulated through the icemaker
for cleaning. Only the water pump operates
at this setting. See the Care and Cleaning section.
select ON.
2. To stop icemaker operation, select OFF.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Features
Icemaker
Features of your
icemaker
Cleaning cycle
light
Light switch
Ice level sensor
Control panel
Cutter grid cover
Water pan
Model & serial
numbers
Magnetic
door catch
Ice retainer
baffle
Lower access
panel
Ice scoop
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Icemaker
How your
icemaker
works
When you first start your icemaker, the water
pan will fill and the system will rinse itself
before starting to make ice. The rinsing
process takes about five minutes.
3. The water containing the rejected minerals
is drained after each freezing cycle.
4. Fresh water enters the machine for the next
ice making cycle.
Under normal operating conditions, the
icemaker will cycle at preset temperatures.
The ice level sensor located in the ice storage
bin will monitor the ice levels.
5. Cubes fall into the storage bin. When
the bin is full, the icemaker shuts off
automatically and restarts when more ice
is needed. The ice bin is not refrigerated
and some melting will occur. The amount
of melting varies with room temperature.
IMPORTANT
• If the water supply to the icemaker is
turned off, be sure to set the icemaker
control to OFF.
• The icemaker is designed to make clear ice
from the majority of water sources on a daily
basis. If your results are unsatisfactory, your
water may need to be filtered or treated.
Making Ice
1. Water is constantly circulated over a freezing
plate. As the water freezes into ice, the
minerals in the water are rejected. This
produces a clear sheet of ice with a low
mineral content.
NOTE: As the room and water temperatures
vary, so will the amount of ice produced and
stored. This means that higher operating
temperatures result in reduced ice production.
2. When the desired thickness is reached, the
ice sheet is released and slides onto a cutter
grid. The grid divides the sheet into
individual cubes.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
Icemaker
Unplug the icemaker before cleaning.
Caring
for your
icemaker
Periodically inspect and clean the icemaker
to keep it operating at peak efficiency.
Clean the ice and water system periodically
to remove mineral scale buildup. Frequency
of cleaning depends on water hardness.
With hard water (15 to 20 grains/gal. [4 to 5
grains/liter]), cleaning may be required as
frequently as every 6 months.
Both the ice making system and the air cooled
condenser need to be cleaned regularly. The
minerals rejected from the circulating water
during the freezing cycle will eventually form
a hard scaly deposit in the water system which
prevents a rapid release of the ice from the
freezing plate.
For best performance, brush or vacuum lint
and dirt from the condenser once a year.
Unscrew the grille on the bottom front of
the cabinet to access the condenser.
Exterior
surfaces
Wash the exterior enamel surfaces and gaskets
with warm water and mild soap or detergent.
Wipe and dry. Regular use of a good
household appliance cleaner and wax will
help protect the finish.
Models with a stainless steel exterior can be
cleaned with a commercially available stainless
steel cleaner using a clean, soft cloth. Do not
use appliance wax or polish on the stainless
steel.
Do not use abrasive cleaners on enamel
surfaces as they may scratch the finish.
Icemaker
system
1. Push the selector switch to OFF.
GE Parts and Accessories. Order part number
WX08X42870. In the U.S.A., call 800.626.2002
or visit GEAppliances.com. In Canada, call
1.888.880.3030.
2. Wait 5 to 10 minutes for the ice to fall into
the storage bin. Remove all ice from the
storage bin.
6. Push the selector switch to CLEAN.
The light will turn on, indicating that the
cleaning cycle is in process.
3. Unscrew the drain cap from the bottom
of the water pan located inside the storage
bin as shown. Allow the water to drain
completely.
7. When the indicator light turns off
(approximately 45 minutes), the cleaning
cycle is complete. During the cleaning cycle,
the system will both clean and rinse itself.
Drain cap
Water pan
8. After the cleaning cycle is complete, remove
the drain cap from the water pan to see if
any cleaning solution is left in the water pan.
If cleaning solution drains from the water
pan, you should run the clean cycle again.
4. Replace the drain cap.
5. Use one 16 oz. bottle of Nickel Safe Ice
Machine Cleaner by Nu Calgon. Read and
follow all safety precautions on the bottle.
Pour one bottle of solution into the water
reservoir. Fill the bottle twice with tap water
and pour it into the water reservoir.
NOTE: Severe scale buildup may require
repeated cleaning with a fresh quantity of
cleaning solution.
9. Push the selector switch to ON to resume
Nickel Safe Ice Machine Cleaner by Nu Calgon
is available at appliance repair shops, or through
ice production.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
Icemaker
Condenser
A dirty or clogged condenser:
4. Remove dirt and lint from the condenser
fins and the unit compartment with a brush
attachment attached to a vacuum cleaner.
• Prevents proper airflow.
• Reduces ice making capacity.
• Causes higher than recommended operating
temperatures which may lead to component
failure.
1. Unplug the icemaker or disconnect power.
2. Remove the 2 screws in the lower access
panel and the 2 screws from the base grille
area of the front panel support. Pull forward
to remove the lower access panel.
3. Pull the bottom forward and then pull down
to remove the lower access panel.
5. Replace the lower access panel using the
4 screws.
6. Plug in the icemaker or reconnect power.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
Icemaker
Interior
1. Unplug the icemaker or disconnect power.
8. Remove the two screws that hold the water
pan in place. Push down with one hand on
2. Open the storage bin door and remove any
ice that is in the bin.
3. Remove the drain cap from the water pan
and drain thoroughly. Replace the drain
cap.
4. Remove the three screws that hold the
cutter grid cover in place.
5. Unplug the wiring harness from the left side
of the cutter grid.
the front of the pan while pulling forward
on the bottom back side.
9. The cutter grid, exterior of hoses, water
pan, storage bin, door gasket and ice scoop
should be cleaned with mild soap or
detergent and warm water. Rinse in clean
water. Then clean the same parts with a
solution of 1 tablespoon (15 mL) of
household bleach in 1 gallon (3.8 L)
warm water. Rinse again thoroughly in
clean water.
Cutter
grid
cover
Screws
6. Unplug the ice level sensor from the right
side of the cutter grid. Pull the ice level
sensor down and forward away from the
cutter grid.
NOTE: Do not remove hoses. Do not wash
plastic parts in dishwasher. They cannot
withstand high temperatures.
7. Remove the right-hand screw and loosen the
left-hand screw. Lift the cutter grid up and
out over the left-hand screw.
10. Wash only the outside of the plastic hoses
with mild soap or detergent and warm
water. Rinse with clean water.
NOTE: Make sure the plastic spacer from the
right-hand side of the cutter grid bracket stays
with the cutter grid.
11. Replace water pan by pushing back on the
bottom with one hand while pushing up
and back on the top. Secure the water pan
by replacing both screws.
Wiring
12. Check the following:
harness
OFF
ON
CLEAN
• Drain cap from the water pan is in place.
Screw
• Hose from the water pan is inserted into
the storage bin drain opening.
Screw
13. Slide the cutter grid back into place and
secure it by replacing the right-hand screw
and tightening the left-hand screw.
Reconnect the electrical and ice level
sensor harnesses.
Cutter
grid
Plastic
spacer
14. Replace the cutter grid cover with three
screws.
Ice level
sensor
15. Plug in the icemaker or reconnect power.
16. Reset the controls. See the Set controls
section.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Cleaning
Icemaker
Light bulb
replacement
The icemaker has a light bulb in the top of the
storage bin. To replace it, open the bin door
and follow these instructions:
1. Unplug the icemaker or disconnect power.
2. Remove the 3 screws that hold the cutter
grid cover in place. Reach behind the
control panel and pull the light bulb down.
3. Replace with a 12-volt wedge base-type bulb
(automotive #917). Locate the light bulb
receptacle at the top behind the control
panel. Align the flat edge of the light bulb
with the receptacle and snap the bulb
into place.
4. Replace the cutter grid cover with the
3 screws.
5. Plug in the icemaker or reconnect power.
Vacation
and moving
To shut down the icemaker:
5. Disconnect the inlet and outlet lines to
water valve. Allow these lines to drain and
then reconnect to the valve.
1. Unplug the icemaker or disconnect power.
2. Remove all ice from the storage bin.
3. Shut off the water supply.
6. Replace the lower access panel and screws.
Drain water from water pan by removing
the drain cap. Also, remove water from
drain line.
4. Remove the 2 screws in the lower access
panel and the 2 screws from the base grille
area of the front panel support. Pull forward
to remove the lower access panel.
7. Before using again, clean the icemaker
and storage bin.
8. Plug in the icemaker or reconnect power.
NOTE: All components of the icemaker are
permanently lubricated at the factory. They
should not require any additional oiling
throughout the normal life of the machine.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation
Icemaker
Front
leveling legs
Your icemaker has 2 adjustable leveling legs to
help you steady the product and make sure it
is level.
1. Place a carpenter’s level on top of the
icemaker to make sure it is level from front
to back and side to side.
2. Lift the top front of the icemaker to locate
the leveling screws that are on the bottom
front.
3. Using an adjustable wrench, change the
height of the legs as follows:
•Turn the leveling leg to the right to lower
that side of the icemaker.
•Turn the leveling leg to the left to raise that
side of the icemaker.
NOTE: The icemaker should not wobble.
Use shims to add stability when needed.
Raise
Lower
4. Use a carpenter’s level to make sure the
icemaker is even from front to back and side
to side.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Reversing the Door Swing
Icemaker
TOOLS NEEDED: 5⁄16″ wrench, 1⁄4″ wrench,
To reverse
the door
To reverse the hinges:
flat putty knife, Phillips screwdriver
1. Using a flat putty knife, remove the plug
buttons from the screw holes opposite of the
door hinges, top and bottom. Set aside.
Parts Supplied:
2. Remove the two screws holding the top
hinge. Turn the hinge upside down so that
the hinge pin points up. Place the hinge on
the opposite side at the bottom of the door.
Four plug buttons
3. Remove the plastic hinge sleeve from the
“old” bottom hinge and replace it on the
new bottom hinge pin.
Parts Identification: (For Reference Only)
4. Remove the bottom hinge. Turn the hinge
upside down so that the hinge pin points
down. Place the hinge on the opposite side
at the top of the door.
Hinge Pin
Handle Screw
Endcap Screw
5. Push the plug buttons into the original
5/16″ Hex Head
screw holes.
Hinge Screw
6. Remove the top hinge pin.
IMPORTANT: Before you begin, unplug the
icemaker or disconnect power.
To remove door from hinges:
1. Remove the handle screws and lift off the
handle (on some models). Keep the parts
together and set them aside.
Top Hinge
2. Remove the hinge pin from the top hinge.
3. Lift the door off of the bottom hinge.
Place the hinge pin back into the top hinge.
4. Reverse the door endcaps as follows:
•Remove the screws and endcaps from the
door, top and bottom.
•Place the top endcap on the bottom of the
opposite side of the door with the long flat
side facing the door front.
Bottom Hinge
•Place the bottom endcap on the top of the
opposite side of the door with the long flat
side facing the door front.
5. Set the door aside.
Bottom Hinge
Top Hinge
Hinge Pin
Hinge Sleeve/
Door Stop
Hinge
Plugs
Hex Head
Hinge Screw
Hinge Sleeve/
Door Stop
Plugs
Hinge
Hinge Pin
18
Hex Head Hinge Screw
Download from Www.Somanuals.com. All Manuals Search And Download.
Reversing the Door Swing
Icemaker
To reverse
the door
To replace door on hinges:
1. Place plastic hinge sleeve on bottom hinge
and position the door on the pin.
2. Place plastic hinge sleeve in the top hinge
hole on the door. Align the door on the
bottom hinge and replace the top hinge pin.
3. Replace the handle and handle screws.
To reverse the door catch:
1. Remove the plugs buttons from the opposite
side of the door.
2. Remove the screws from the magnetic door
catch and replace it on the opposite side of
the door.
3. Push the plug buttons into place on the
opposite side of the door.
Reverse
Door Catch
Position
19
Download from Www.Somanuals.com. All Manuals Search And Download.
The Problem Solver
Icemaker
PROBLEM
POSSIBLE CAUSE
•
•
•
Power cord is not plugged into a live outlet.
The control is set at OFF.
The fuse is blown/circuit breaker is tripped. Replace fuse or
reset the breaker.
Room temperature is colder than normal. Room temperature
must be above 55˚F (13˚C). Otherwise, bin thermostat may
sense cold room temperature and shut off even though the bin
is not full of ice. Also, unit may not restart once it does shut off.
ICEMAKER DOES NOT
OPERATE
Questions?
Use this
problem solver!
•
•
•
•
High mineral content in the water supply. Water may need to
be filtered or treated.
Food items stored in ice bin. Do not store any foods in the
ice bin.
Packaging materials were not removed. Make sure that all
packaging materials were removed at the time of installation.
ICE CUBES HAVE
ODOR/TASTE
•
•
Ice storage bin needs cleaning.
Scale has built up in the icemaker. If there is white scale
buildup in the icemaker’s water or freezing system, you should
clean the icemaker. See Care and Cleaning---Icemaker System.
•
•
•
The control is set at OFF.
Water supply is not connected.
Condenser is dirty. Dirt or lint may be blocking the airflow
through the condenser. See Care and Cleaning---Condenser.
ICEMAKER IS ON, BUT
DOESN’T PRODUCE ICE
•
Scale has built up in the icemaker. If there is white scale
buildup in the icemaker’s water or freezing system, you should
clean the icemaker. See Care and Cleaning---Icemaker System.
•
•
•
Room temperature is too hot. Room temperatures of more
than 90˚F (32˚C) will normally reduce ice production.
Condenser is dirty. Dirt or lint may be blocking the airflow
ICEMAKER IS ON, BUT
PRODUCES LITTLE OR
NO ICE
through the condenser. See Care and Cleaning---Condenser.
Scale has built up in the icemaker. If there is white scale
buildup in the icemaker’s water or freezing system, you should
clean the icemaker. See Care and Cleaning---Icemaker System.
•
•
Water is leaking from the water pan because the drain cap is
not secure. Make sure the drain cap is securely tightened.
Cutter grid is not securely in place. Unplug the icemaker or
disconnect power. Remove the cutter grid cover and check the
cutter grid harness plug to make sure the connection is
secure. For instructions on removing and replacing the cutter
grid and the location of the harness plug, see Care and
Cleaning---Interior.
GRID IS NOT CUTTING
ICE SHEETS
•
The ice sheet is trapped on the cutter grid. Unplug the
icemaker or disconnect power. Remove the cutter grid cover
and move the ice sheet to the cutter grid. Make sure the cutter
grid is lined up with the freezing plate. See Operating
ICEMAKER PUMPS
CONTINUOUSLY, BUT
PRODUCES NO ICE
Instructions---How your icemaker works. If it is not lined up with
the freezing plate, adjust the cutter grid. For instructions on
removing and replacing the cutter grid, see Care and Cleaning---
Interior. Reinstall the cutter grid cover and reconnect power.
Turn on the icemaker. The icemaker will reset itself and start a
new cycle after flushing water through the system.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
o d a y M a i l T t a n t I m p o r
e g i s t r a t i o n O w n e r s h i p R
o d u c t C o n s u m e r P r
G E A p p l i a n c e s
Place
1st Class
Letter
Stamp
Here
General Electric Company
Warranty Registration Department
P.O. Box 32150
Louisville, KY 40232-2150
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Product Ownership Registration
Dear Customer:
Thank you for purchasing our product and thank you for placing your confidence in us. We are proud to
have you as a customer!
Follow these three steps to protect your new appliance investment:
Complete and mail
your Consumer
After completing this
registration, write your
model and serial numbers
in this manual. You will need
this information should
you require service. The
service number in the
USA: 800.444.1845.
Read your “Owner’s
Manual” carefully.
It will help you
operate your new
appliance properly.
Product Ownership
Registration today.
Have the peace of mind
of knowing we can
contact you in the
unlikely event of a
safety modification.
1
2
In Canada, call:
3
1.888.880.3030.
Important: To ensure that your product is registered, mail the separate product registration card.
If the separate product registration card is missing, fold and mail the form below. No envelope is needed.
FOLD HERE
Consumer Product Ownership Registration
Product
Model
Serial
Icemaker
Miss l
Mr. l Ms. l Mrs. l
First
Name
Last
Name
Street
Address
Apt. #
Zip
Code
City
State
Date Placed
In Use
Month
Phone
Number
Day
Year
monogram.com
Monogram®
General Electric Company
Louisville, KY 40225
✄
TAPE CLOSED
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Services
Icemaker
With the purchase of your new Monogram appliance, receive the
assurance that if you ever need information or assistance from GE,
we’ll be there. All you have to do is call---toll-free!
Whatever your question about any Monogram major appliance, GE Answer Center®
information service is available to help. Your call---and your question---will be answered
promptly and courteously. And you can call any time. GE Answer Center® service is open
24 hours a day, 7 days a week.
GE Answer
Center®
In the USA:
800.626.2000
OR
Visit our Website at: monogram.com
In Canada, call 1.888.880.3030.
In-Home Repair
Service
A GE consumer service professional will provide expert repair service, scheduled at a time
that’s convenient for you. Many GE Consumer Service company-operated locations offer
you service today or tomorrow, or at your convenience (7:00 a.m. to 7:00 p.m. weekdays,
9:00 a.m. to 2:00 p.m. Saturdays). Our factory-trained technicians know your appliance
inside and out---so most repairs can be handled in just one visit.
In the USA:
800.444.1845
In Canada:
1.888.880.3030
For Customers
With Special
Needs…
GE offers Braille controls for a variety of GE appliances, and a
brochure to assist in planning a barrier-free kitchen for persons with
limited mobility.
Consumers with impaired hearing or speech who have access
to a TDD or a conventional teletypewriter may call 800.TDD.GEAC
(800.833.4322) to request information or service.
In the USA:
800.626.2000
Service Contracts
You can have the secure feeling that GE Consumer Service will still be there after your
warranty expires. Purchase a GE contract while your warranty is still in effect and you’ll
receive a substantial discount. With a multiple-year contract, you’re assured of future
service at today’s prices.
In the USA:
800.626.2224
In Canada:
1.888.880.3030
Parts and
Accessories
Individuals qualified to service their own appliances can have parts or accessories sent directly
to their home. The GE parts system provides access to over 47,000 parts…and all GE Genuine
Renewal Parts are fully warranted. VISA, MasterCard and Discover cards are accepted.
In the USA:
800.626.2002
User maintenance instructions contained in this manual cover procedures intended to be
performed by any user. Other servicing generally should be referred to qualified service
personnel. Caution must be exercised, since improper servicing may cause unsafe operation.
In Canada:
1.888.880.3030
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Icemaker
YOUR MONOGRAM ICEMAKER WARRANTY
Staple sales slip or cancelled check here. Proof of original purchase
date is needed to obtain service under warranty.
WHAT IS
COVERED
From the Date
of the Original
Purchase
FULL ONE-YEAR WARRANTY
For one year from date of original purchase, we will provide, free of charge, parts and service
labor in your home to repair or replace any part of the icemaker that fails because of a
manufacturing defect.
FULL FIVE-YEAR WARRANTY
For five years from date of original purchase, we will provide, free of charge, parts and service
labor in your home to repair or replace any part of the sealed icemaking system (the compressor,
condenser, evaporator and all connecting tubing) that fails because of a manufacturing defect.
This warranty is extended to the original purchaser and any succeeding owner for products
purchased for ordinary home use in the 48 mainland states, Hawaii and Washington, D.C. or
Canada. In Alaska, the warranty is the same except that it is LIMITED because you must pay to
ship the product to the service shop or for the service technician’s travel costs to your home.
All warranty service will be provided by our Factory Service Centers or by our authorized
Customer Care® servicers during normal working hours.
Should your appliance need service, during warranty period or beyond, in the U.S.A.,
call 800.444.1845. In Canada: 888.880.3030.
• Service trips to your home to teach you how
to use the product.
• Improper installation.
WHAT IS NOT
COVERED
If you have an installation problem, contact
your dealer or installer. You are responsible
for providing adequate electrical, plumbing
and other connecting facilities.
• Replacement of house fuses or resetting
of circuit breakers.
• Damage to the product caused by accident,
fire, floods or acts of God.
• Incidental or consequential damage caused
by possible defects with this appliance.
• Failure of the product if it is used for
other than its intended purpose or used
commercially.
Some states/provinces do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which vary from state to state/province
to province. To know what your legal rights are in your state/province, consult your local or
state/provincial consumer affairs office or your state’s Attorney General.
Warrantor: General Electric Company. If further help is needed concerning this warranty,
write: Manager---Customer Relations, GE Appliances, Louisville, KY 40225
Part No. 2217244
Pub No. 49-60027-1
12-01 JR
Monogram®
General Electric Company
Louisville, KY 40225
Printed in the United States
Download from Www.Somanuals.com. All Manuals Search And Download.
|