INFO HOT-LINE: If, after reading this owner’s
¤
guide you have any questions or comments,
please call 1-877-207-0923 and a Consumer Service
Representative will be happy to assist you.
106573
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
PLEASE READ AND SAVETHESE
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ AND
When using electrical appliances, basic safety pre-
cautions should always be taken including the fol-
lowing:
SAVETHESE
IMPORTANT SAFETY
• Use fan only for purposes described in the
instruction manual.
• To protect against electrical shock do not
immerse unit, plug or cord in water or spray
INSTRUCTIONS
with liquids.
• Close supervision is necessary when any appli-
ance is used by or near children.
• Unplug from outlet when not in use, when mov-
ing fan from one location to another, before put
ting on or taking off parts, and before cleaning.
• Avoid contact with moving parts.
• Do not operate in the presence of explosive and
or flammable fumes.
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC
(Alternating Current)PLUG (a plug having one blade
wider than the other).This plug will fit into the
power outlet only one way. If the plug does not fit
fully into the outlet, reverse the plug. If it still does
not fit, contact qualified personnel to install the
proper outlet. DO NOT DEFEATTHE SAFETY PUR-
POSE OFTHIS POLARIZED PLUG IN ANY WAY.
• Do not place fan or any parts near an open
flame, cooking or other heating appliance.
• Do not operate any appliance with a damaged
cord, plug, after the appliance malfunctions, or
has been dropped / damaged in any manner.
• The use of attachments not recommended or
sold by the appliance manufacturer may cause
hazards.
ASSEMBLY INSTRUCTIONS
Base / Pole Assembly
Step 1: Slide the bottom end of the outer pole through
the pole ring.
Step 2: Turn the base cover upside down and place the
weighted insert and washer into the base cover.
Step 3: Insert the threaded end of the L shaped locking
lever into the hole of the washer, weighted insert
and through the base cover.
Step 4: While holding the base and weighted insert
together, connect the pole to the base, sliding the
washer and L shaped locking lever into the bot-
tom of the outer pole.
Step 5: Turn the L shaped locking lever clockwise to
securely attach the pole to the base.
Step 6: Set the base on the floor, weight side down. Push
the pole ring down until it sits directly on the
base.
• Do not use outdoors.
• Do not let the cord hang over the edge of a
table, counter or come in contact with hot sur-
faces.
• To disconnect, grip plug and pull from wall out
let. Never yank on cord.
• Always use on a dry, level surface.
• Do not operate without fan grills properly in
place.
• This product is intended for household use
ONLY and not for commercial or industrial
applications.
Fan Head Assembly
Step 1: Position the rear grill over the motor shaft, mak-
ing certain the notches at the top and bottom of
the rear grill fit over the prongs on the motor
housing. Please make sure the rear grill fits
securely against the motor housing.
Step 2: Secure the rear grill in its place using the rear
grill mounting-ring. Turn this ring clockwise and
tighten firmly.
WARNING: To reduce the risk of fire or electrical
shock, DO NOT USE THIS FAN, with any SOLID
STATE Fan Speed Control Device.
Step 3: Slide the fan blade, with the hollowed interior of
the blade facing toward the rear grill, firmly
onto the motor shaft. The top of the motor shaft
Download from Www.Somanuals.com. All Manuals Search And Download.
should lie even with the center of the fan blade.
ADJUSTMENT INSTRUCTIONS
ASSEMBLY INSTRUCTIONS CONT.
Tilt Adjustment
Step 4: Align the flat of the shaft with the securing screw
on the fan blade and slide the fan blade onto
the shaft with the securing screw facing the rear
grill.
Step 5: Center the front grill by aligning the GE Brand
logo on the logo plate so it is upright and
straight. Then, holding the front grill against the
rear grill snap each clip forward onto the front
grill.
Step 1: To change the tilting angle of the fan head, sim-
ply loosen the Tilt Adjustment Knob.
Step 2: Move the fan head to the desired angle, and then
firmly tighten the knob to lock the fan head in
place.
Height Adjustment
Step 1: Turn the Pole Lock Knob counter clockwise to
loosen the inner pole.
Step 2: Adjust the inner pole to the desired height, and
firmly tighten the pole lock knob in a clockwise
direction.
WARNING: Make sure to support the fan head
assembly when loosening the adjustable height
knob, as the weight of the fan head may cause the
inner pole to collapse.
Final Assembly
Step 1: First, slide the inner pole up from the outer pole.
Insert the Pole Lock Knob into the hole on the
outer pole, to securely hold this position. Next,
place the fan head assembly into the inner pole,
inserting the neck of the fan into the pole open
ing. Turn the fan head’s neck until the head is
securely locked into place. Finally, add the Tilt
Adjustment Knob to the hole of the fan head’s
neck. Tighten when fan head is in the desired
position.
CLEANING/MAINTENANCE
INSTRUCTIONS
Follow these instructions to correctly and safely care for
your GE Brand stand fan. Please remember:
•
•
•
Always unplug the fan before cleaning or disassem-
bling.
Do not allow water to drip on or into the fan motor
housing.
Do not use any of the following as a cleaner: gasoline,
thinner, benzine.
OPERATING INSTRUCTIONS
Step 1: Set the fan base on a dry, level surface.
Step 2: Please make sure the On/Speed switch is in the
"Off" position. Plug the cord into any standard
120-volt A/C outlet.
(See instructions for fan head assembly)
Step 1: To access the fan blade, remove the front grill
and then unscrew the securing screw on the fan
blade.
Step 3: The SPEED is adjusted by moving the switch left
or
right to the desired setting.
Step 2: Clean the fan blade, both front and rear grills
with a soft cloth moistened with a mild soap solu-
tion.
Step 3: Replace blade, tighten the fan blade by screwing
the fan blade back on, and securely fasten the
front grill.
Step 4: The OSCILLATION knob is located on
the top of the fan motor housing. To start oscilla-
tion, push control knob down. To stop oscillation,
pull control knob up.
Q
C
Fan Head, Base, and Pole Cleaning
G
Using a soft, moist cloth, with or without a mild soap solu-
tion, carefully clean the fan base, pole, and head. Please
use caution around the motor housing area. Do not allow
the motor or other electrical components to be exposed
to water.
H
A.) Front Grill
B.) Fan Blade
C.) Securing Screw
D.) Rear Grill Mounting-Ring
E.) Rear Grill
D
I
F
J
A
B
E
F.) Motor Shaft
G.) Motor Housing
H.) Tilt Adjustment Knob
I.) Inner Pole
K
L
FAN STORAGE
J.) Pole Lock Knob
K.) Outer Pole
L.) Pole Ring
Your fan can be stored in the off-season either partially
disassembled or assembled. It is important to keep it in a
safe, dry location.
M
M.)Base
N.) Weighted Insert
O.) Washer
P.) L Shaped Locking Lever
Q.) Grill Clips (6)
•
If stored disassembled, we recommend using the origi-
nal (or appropriately sized) box.
If stored assembled or partially assembled, remember
N
•
O
Download from Www.SomanualPs.com. All Manuals Search And Download.
to protect the fan head from dust.
WARRANTY INFORMATION
SERVICE INSTRUCTIONS
1. Do NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void the warranty.
2. If you have any questions regarding this units operation or believe any repair is necessary, please call 1-877-207-0923 to
speak with a Consumer Service Representative.
3. If you need to exchange the unit, please return it in the original carton, with a sales receipt, to the store you purchased it.
If you are returning the unit more than 30 days after the date of purchase, please see the enclosed warranty.
4. If you have any other questions or comments, feel free to write us:
Consumer Service Department
P.O. Box 769, Milford, MA 01757-0769
For your own records, staple or attach your sales receipt to this manual. Also, please take a moment to write the store
name/location and date purchased below.
STORE NAME:
LOCATION:
DATE PURCHASED:
(STAPLE RECEIPT HERE)
FIVE (5)YEAR LIMITED WARRANTY
SAVETHIS WARRANTY INFORMATION
What does your warranty cover?
•Any defect in material or workmanship
For how long after the original purchase?
•5 years.
What will we do?
•Provide you with a new, or at our option, a reconditioned unit.
•The exchange unit is warranted for the remainder of your product’s original five year warranty period.
How do you make a warranty claim?
¤
•Return the product to your nearest WAL MART store.
•Properly pack your unit. We recommend using the original carton and packing materials.
•Include in the package a copy of the sales receipt or other evidence of date of original purchase. If the
unit was a gift, provide a statement specifying the date received. Also print your name and address and a
description of the defect.
•A new or reconditioned unit will be provided.
What does your warranty not cover?
•Customer instruction. This instruction manual provides information regarding operating instructions
and user controls. For additional information, ask your dealer.
•Commercial use.
•Damage from misuse, abuse, or neglect.
•Products which have been modified or incorporated into other products.
•Products purchased or serviced outside the USA.
How does state law relate to this warranty?
•This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state.
What if you purchased your product in the U.S., Canada or Mexico and encounter a problem while using it
outside the country of purchase?
•The warranty is valid only in the country of purchase and if you follow the warranty claim procedure as
noted.
¤
GE is a trademark of General Electric Company and is used under the license by WAL MART Stores, Inc.
Bentonville, AR 72716
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in China
12/5/00 last update
GE10657300UM1
|