GE Door 19234 User Manual

GE Model 19234  
The chime and pushbutton must be set to the same  
house security code for the combination to operate  
together.  
Push Button Mounting Instructions  
9. Test operation. If the chime does not work, see  
TROUBLESHOOTING.  
If you do not want to drill holes in your door frame, you  
can use the supplied double sided tape for installation.  
1. Clean all mounting surfaces with a 50/50 mixture of  
isopropyl alcohol.  
2. Remove the backing from one side of the double  
sided tape and press the exposed side against the  
back plate of the push button.  
3. Remove the other backing strip and press the  
exposed side against the door frame where you want  
the button installed.  
Note: Avoid mounting on metal surfaces, as it may  
result in a reduced range of transmission. Do not mount  
in an area where exposed to direct rain.  
1. Remove power from the chime.  
2. To remove the batteries from the pushbutton,  
open the pushbutton case as shown below.  
Wireless Door Chime Kit  
a. Removing the back cover  
Installation Instructions AC Wireless Chime Kit  
Required Tools: Small flat blade screwdriver, drill,  
1/16” drill bit, and phillips screwdriver.  
Included Hardware:  
(2) 3x20mm screws  
(1) Double sided adhesive pad  
Power Indicator  
b. Replacing the back cover  
The wireless door chime kit has two components:  
Pushbutton  
House Code  
Jumpers  
On/Off Switch  
Operation  
Mounting Push Button  
1. Push buttons are typically mounted at the same  
height as the door knob or handle (between 36” and  
44” above the floor).  
2. Before mounting, choose a mounting location that  
is not farther than 150 feet from the chime unit  
location.  
1. Plug the chime into a 120V AC outlet and slide the  
power switch to the “On” position to turn on the  
chime. The red LED power indicator will light.  
2. Gently press transmitter button to sound chime.  
Battery Operated  
PushButton (Transmitter)  
Battery included  
Pushbutton Jumpers  
Chime (Receiver)  
Plugs into 120V outlet  
3. Locate the House Security Code door and screw  
located on the back of the Chime. Remove the  
screw and take off the door.  
4. Locate the chime and pushbutton jumpers shown  
above.  
5. To change the house code, add or remove jumpers  
as needed. It is recommended to change only one  
jumper at a time and then test the system for proper  
operation. The jumpers on the chime and pushbutton  
must match exactly.  
Troubleshooting  
Setting The House Security Code  
Not further than 150 feet  
Chime doesn’t work:  
1. Make sure push button switch is depressed and held  
for at least 1 second.  
2. Make sure house code switches 1-4 on chime and  
push button match exactly.  
3. Verify battery orientation in push button.  
4. Try fresh batteries.  
5. Make sure chime is not farther than 150 feet away  
from push button.  
Each chime component has 3 jumpers for setting the  
house security code. In most cases you will not need  
to change the factory settings for the house security  
code. If your chime activates intermittently or does not  
work at all, you may be able to solve the problem by  
changing your security code.  
Wireless push button battery  
6. Ensure push button is not mounted on metal, near  
metal studs, or near the floor.  
7. Try a new location for the chime.  
To install or replace the battery in the wireless push  
button.  
3. Before placing the pushbutton where you would like  
to mount it, place the chime as close to final position  
as possible. Test the operation before drilling. If it  
works, mount the push button. If it does not work,  
see TROUBLESHOOTING.  
Functional range may be adversely affected by one or  
more of the following factors: weather, radio frequency  
interference, low transmitter battery and obstructions  
between the transmitter and receiver.  
This device complies with Part 15 of the FCC rules.  
Operation is subject to the following conditions:  
1. This device may not cause harmful interference, and  
2. This device must accept interference received,  
including any interference that may cause undesired  
operation.  
1. Remove the back cover of the push button.  
4. Use back cover of push button as a template to mark  
two screw holes.  
2. Install the A23 (12 volt) battery with the negative  
side of the battery (-) toward the spring and the  
positive side of the battery (+) toward the positive  
battery holder as shown below.  
For technical support contact Jasco Products  
Company at 1-800-654-8483  
4
Made in China/Hecho en China  
5
Pushbutton  
House Code  
Jumpers  
is a trademark of  
6
General Electric Company  
and is used under license to  
Jasco Products Company LLC,  
10 E. Memorial Rd.,  
8
5. Drill two holes with 1/16” size drill in marked  
locations.  
Oklahoma City, OK 73114.  
3. Replace back cover as shown below.  
6. Secure back cover to the mounting surface with two  
supplied mounting screws.  
7. Install the supplied 12V battery observing proper  
polarity. (see battery installation section)  
8. Press front housing onto back cover.  
Rev. 04-10  
19234  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19234-1.indd  
1
4/14/10 3:58 PM  

Eicon Networks Network Card DMV600BTEC User Manual
Eiki Projector EIP 1000T User Manual
Eizo Computer Monitor EV2411W User Manual
Extron electronic Car Amplifier 68 1376 01 User Manual
Fostex DVR D 160 User Manual
Frigidaire Double Oven FFET2725L User Manual
GarrettCom Switch DS80C User Manual
GE Answering Machine 2 9824 User Manual
GE Griddle 169148 User Manual
GE Range 164D2966P053 User Manual