Safety Instructions . . . . . . . . . . .2, 3
Installation Instructions . . . . . . . .4
Owner’s Manual
and Installation
Operating Instructions
Automatic Humidity Control . . . . . .6
Control Settings . . . . . . . . . . . . . .5, 6
Locking the Controls . . . . . . . . . . . .6
Care and Cleaning . . . . . . . . . .7–10
Replacing the Light Bulb . . . . . . . . .8
Reversing the Door . . . . . . . . . . .9, 10
Troubleshooting Tips . . . . . . .11, 12
Consumer Support
Warranty . . . . . . . . . . . . . . . . . . . . .13
Consumer Support . . . . . . . . . . . . .14
Write the model and serial
numbers here:
Model # ____________________
Serial # ____________________
Find these numbers inside the
wine chiller on the left side.
Part No. – 3504502P327
Cat. No. – WR6M460
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock
hazard from this appliance.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your wine chiller by pulling on
the power cord. Always grip plug firmly and
pull straight out from the outlet.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
Repair or replace immediately all power cords
that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
If you have only a standard 2-prong wall outlet,
it is your personal responsibility and obligation
to have it replaced with a properly grounded
3-prong wall outlet.
When moving the wine chiller away from the
wall, be careful not to roll over or damage the
power cord.
The wine chiller should always be plugged into
its own individual electrical outlet which has
a voltage rating that matches the rating plate.
USE OF ADAPTER PLUGS
Adapter plugs are not permitted in Canada.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the wine chiller.
Removing the Packaging
Before using the wine chiller, be sure all packing materials and tape have been removed,
including the protective film covering the control and any film protecting the cabinet.
If you are discarding an old refrigeration product, remove the doors to reduce the danger
of children being trapped inside.
Installation Guidelines
■ The wine chiller can be freestanding
or can be installed under the counter,
with proper clearances.
■ Do not install the wine chiller where
the temperature will go below 55°F
(13°C) or above 90°F (32°C).
■ Allow the following clearances for ease
of installation, proper air circulation
and electrical connections:
■ Install it on a level floor.
■ Do not install the wine chiller where it
will be subject to direct sunlight, heat
or moisture.
Each side
Top
11⁄2″ (38 mm)
2″ (51 mm)
2″ (51 mm)
■ Do not store or install this appliance
outdoors.
Back
Leveling Legs
Adjustable legs at the front corners of
the wine chiller should be set so the
wine chiller is firmly positioned on the
floor, with a 1/8″ (3 mm) tilt to the back
to help the door closure.
To adjust the leveling legs, turn the legs
clockwise to raise the wine chiller,
counterclockwise to lower it.
To raise the wine chiller
4
Download from Www.Somanuals.com. All Manuals Search And Download.
About the control and settings.
Control Settings
Press the CUSTOM TEMP pad. This will convert
the RED WINE and WHITE WINE pads into temp
up and temp down pads. Short taps to these pads
will change the temperature setting slowly. To
change the temperature setting more quickly,
press and hold the pad.
The controls give you three setting options.
RED WINE—Use for the storage of red wines.
This setting will provide a storage temperature
of 55°F (13°C), which is optimum for the
storage of red wine.
WHITE WINE—Use for the storage of white
wines. This setting will provide a storage
temperature of 45°F (7°C), which is optimum
for the storage of white wine.
When you make your selection (WHITE WINE,
RED WINE or CUSTOM TEMP) you will see the set
temperature show up in the display. However,
shortly after the selection has been made, the
display will show the actual temperature of the
wine chiller. You will then see the temperature
in the display change as the actual temperature
of the wine chiller reaches the set temperature.
CUSTOM TEMP—This setting allows you to
customize the temperature when storing both
red and white wines. The custom temperature
can be set anywhere between 40° to 65°F
(4° to 18°C). The recommended temperature
when storing half red wine and half white
wine is 50°F (10°C).
NOTE: In the event of a power failure, when the
power is restored, the controls automatically are
set to the RED WINE setting. If needed, reset the
controls to the desired setting.
Loading the Wine
As with any refrigeration product, there is
a slight temperature variance at different
locations within the cabinet. In this wine
chiller, the lower shelves provide a slightly
cooler temperature than the upper shelves.
When storing both red and white wines,
it is best to store the white wine on the
lower shelves where the temperature is
slightly cooler.
Suggested bottle arrangement
When the Wine Chiller is Plugged In
After plugging in the wine chiller and making
your selection (WHITE WINE, RED WINE or
CUSTOM TEMP), allow the wine chiller to reach
the set temperature before loading your wine.
This may take up to 12 hours to completely
stabilize.
After loading the wine, you may notice the
actual temperature rise. The adjustment of
the actual temperature reaching the set
temperature will be reflected in the display.
This may take up to 12 hours to completely
stabilize.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
About the controls and settings.
Locking the Controls
This feature allows you to lock the controls so
the temperature settings cannot be changed. The
interior light will still function.
To unlock the controls, simply press and
hold the RED WINE and INTERIOR LIGHT
pads at the same time for 3 seconds.
To lock the controls, press and hold the
RED WINE and INTERIOR LIGHT pads at the
same time for 3 seconds. The word LOC
will appear in the display to indicate the
lockout feature has been activated. The
display will then go back to showing the
actual temperature. Anytime a
temperature pad is pressed while the
lockout feature is activated, LOC will
appear in the display.
Key-Ejecting Lock
The wine chiller can be locked using the
As a safety feature, the key for the spring-
spring-loaded lock located above the door. loaded lock is automatically ejected and
will not remain in the lock in either the
open or closed position.
Wine Chiller Light
Press the INTERIOR LIGHT pad to turn the
interior light on or off.
If you turn on the light and do not turn
it off, it will automatically turn off after
one hour.
Automatic Humidity Control
The inside of the wine chiller
automatically maintains the necessary
level of humidity to protect wine corks
from drying out. As a result, frost may
form on the inner surfaces. See Care and
Cleaning for instructions on removing
excessive frost buildup.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and cleaning.
Cleaning the Outside
IMPORTANT: Unplug the wine chiller before
cleaning.
Stainless steel. Regularly clean and polish
the stainless steel areas (on some models)
with a commercially available stainless
steel cleaner such as Gleem-it® to preserve
and protect the fine finish. Gleem-it® is
available at leading hardware stores. It is
also available through our website,
Keep the outside clean. The cabinet can
be washed with mild soap and water.
Rinse thoroughly with clear water.
Never use abrasive scouring powders.
Use a glass cleaner or mild soap and water
and a soft cloth to clean the glass door.
Do not use any abrasive powders.
1.888.261.3055. Order part number
WX10X15.
Do not use appliance wax or polish on the
stainless steel.
Wipe the control panel with a damp cloth.
Dry thoroughly. Do not use cleaning
sprays, large amounts of soap and water,
abrasives or sharp objects on the panel—
they can damage it. Some paper towels
can also scratch the control panel.
Protect the paint finish. The finish on
the outside of the wine chiller is a
high-quality, baked-on paint finish.
With proper care, it will stay new-looking
and rust-free for years. Apply a coat of
kitchen/appliance wax when the wine
chiller is new, and then at least twice
a year.
Do not wipe the wine chiller with a soiled
dishcloth or towel. These may leave a residue that
can erode the paint. Do not use scouring pads,
powdered cleaners, bleach or cleaners containing
bleach because these products can scratch and
weaken the paint finish.
Cleaning the Inside
IMPORTANT: Unplug the wine chiller before
cleaning.
Do not use detergents, scouring powders,
spray cleaners or other harsh chemicals to
clean the interior.
To clean the inner liner and racks, use
a warm water and baking soda solution—
about one tablespoon (15 ml) of baking
soda to a quart (1 liter) of water. This
both cleans and neutralizes odors.
Rinse and wipe dry.
The vinyl door gasket may be cleaned
with mild soap and water or a baking
soda solution. Rinse well.
Defrosting
Defrost whenever frost on the inside surfaces
of the storage area becomes 1/8″ (3 mm) thick.
Never use a heater of any kind, scraper or
sharp instrument to remove frost as it may
damage the wine chiller.
After defrosting, make sure inside surfaces
are dry; then return the contents to the
wine chiller and set the temperature
control to the desired setting.
To defrost, unplug the wine chiller.
Remove the contents and wipe inside
surfaces and racks with a clean towel.
If frost does not come off easily,
allow the frost to melt somewhat
and wipe off.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and cleaning.
In the Event of a Power Failure
If the power fails, open the door as
infrequently as possible to maintain
the temperature. A gradual rise in
temperature should not have any
adverse effect on the wine.
When power is restored, the controls
automatically are set to the RED WINE
setting. If needed, reset the controls to
the desired setting.
If it is extremely hot, you may want to
unload the wine from the wine chiller and
move the wine to a cooler location until
power is restored.
Preparing to Move
Unload the wine, then secure the racks by
taping them in place to prevent damage.
Be sure the wine chiller stays in an upright
position during the move.
Replacing the light bulb.
Unplug the wine chiller.
If the door is locked, unlock it.
The light bulb is located behind a light shield in the ceiling of the
wine chiller near the front. To remove the light shield, remove the
two screws at the back corners of the shield.
Bulb
Housing
Pull down on the back of the light shield to release the two
front tabs.
Remove the light bulb housing by removing the two screws that
attach the housing to the ceiling of the wine chiller.
Step 5:
Remove two screws
Pull the bulb out of the receptacle. Replace with a 5 watt, 12 volt
bulb. This type of bulb is available at most automotive parts stores.
WARNING:
Using a bulb rated higher than 5 watts may damage
the electronic controls on the wine chiller.
Attach the light bulb housing to the ceiling of the wine chiller with
the two screws. Make sure not to pinch or damage any of the wires
attached to the housing.
Line up the light shield with the indentation on the ceiling of the
wine chiller, then push the front of the shield up until the front tabs
clip into place. Replace the screws at the back of the shield.
Plug the wine chiller back in.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Reversing the Door.
Top cover
Unplug the wine chiller.
Remove the two screws at the back of the top cover.
Lift the back of the cover up about 2″ (5 cm) and then slide it
forward slightly, but do not remove.
Remove screws
Back of wine chiller
Tilt the top cover on its side. Locate the power connectors at the
front of the cover. Disconnect each connector by pressing in on
the locking tab on the side of the connector, then pulling out.
Set cover aside.
Top cover
Disconnect power
connectors
Front of wine chiller
Remove screws and
move to other side
Carefully lay the wine chiller on its back.
Remove the screws on the top hinge (right side). Remove the hinge.
Remove plug button and
move to other side
On the opposite side, remove the screws attaching the top plate to
the cabinet, and install them in the holes left vacant by the top
hinge screws.
Remove the small plug button from the top left side of the door and
install it in the hole on the right side.
Insert the hinge pin from the top hinge into the hole on the top left
side of the door. Attach the top hinge to the cabinet with the screws.
Make sure the door is aligned with the wine chiller cabinet before
tightening the screws.
Top of wine chiller
Remove screws and
top hinge, and move
to other side
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Reversing the Door.
Remove the bottom hinge by removing the screws and leveling leg.
Remove right door
stop and screws.
Install left door stop
(packed separately)
and screws on
Remove the right door stop and install the left door stop
(WR13X10274), packed separately, on the opposite side.
Remove the leveling leg and spacer on the opposite side and install
it on the right side.
other side
IMPORTANT: The left leg has a spacer that must be moved to the right side
leveling leg when the door swing is reversed.
Remove leveling leg
and spacer and move
to other side
Install the bottom hinge, with the screws and leveling leg,
on the left side.
Bottom of
wine chiller
Remove leveling
Stand the wine chiller upright.
leg, screws, bottom
hinge and washer, and
move to other side
Open and close the door, checking the alignment of the door to the
cabinet. If necessary, loosen the screws attaching the top hinge to
the cabinet, realign the door and retighten the screws.
Place the top cover on the cabinet and reconnect the power
connections.
Slide the top cover back in place and replace the two screws.
Plug in the wine chiller. Reset the controls to the desired setting.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
Troubleshooting Tips
Save time and money! Review the charts on the following
pages first and you may not need to call for service.
Problem
Possible Causes
What To Do
Wine chiller does not
operate and the display
is blank
Wine chiller is unplugged.
•Push the plug completely into the outlet.
The circuit breaker is tripped/ •Replace fuse or reset the breaker.
the fuse is blown.
Vibration or rattling
(slight vibration
is normal)
Wine chiller is on an
uneven surface.
•See the Leveling Legs section.
Motor operates for
long periods or cycles
Normal when wine chiller
is first plugged in.
•Wait 12 hours for the wine chiller to completely
cool down.
Often occurs when large
amounts of wine are placed
in wine chiller.
•This is normal.
Door left open.
•Door is not self-closing. Always make sure that the
door is closed after opening.
•Check to see if a bottle is holding door open.
Hot weather or frequent
door openings.
•This is normal.
Temperature control set
at the coldest setting.
•See About the control and settings.
Wine chiller is too close
to the wall.
•See the Installation Guidelines section for the
correct clearances.
Wine chiller too warm
Normal when wine chiller
is first plugged in.
•Wait 12 hours for the wine chiller to completely
cool down.
Often occurs when large
amounts of wine are placed
in wine chiller.
•This is normal.
Temperature control
not set cold enough.
•See About the control and settings.
Warm weather or frequent
door openings.
•Set the temperature control one step colder.
See About the control and settings.
Wine chiller is too close
to the wall.
•See the Installation Guidelines section for the
correct clearances.
Door left open.
•Door is not self-closing. Always make sure that the
door is closed after opening.
•Check to see if a bottle is holding door open.
If the temperature setting is
not showing what you last
selected, a power outage
may have occurred.
•When the power came back on, the wine chiller
returned to the default setting, which is RED WINE.
Reset the control to the desired setting.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you call for service…
Problem
Possible Causes
What To Do
Wine chiller has odor
Interior needs cleaning.
•See Care and cleaning.
•Wipe surface dry.
Moisture forms on
outside of wine chiller
Not unusual during periods
of high humidity.
Moisture collects inside
Too frequent or too long
door openings.
(in humid weather,
air carries moisture
into wine chiller when
door is opened)
Wine bottles touching
the back wall.
•Reposition bottles.
Frost forms on interior
surfaces of wine chiller
This is normal.
Door left open.
•See the Defrosting section.
•Excessive frost may form if the door is left open.
See the Defrosting section.
•Door is not self-closing. Always make sure that the
door is closed after opening.
•Check to see if a bottle is holding door open.
•See About the control and settings.
Wine chiller too cold
Temperature control
is set too cold.
If the temperature setting is
not showing what you last
selected, a power outage
may have occurred.
•When the power came back on, the wine chiller
returned to the default setting, which is RED WINE.
Reset the control to the desired setting.
The room temperature where
the wine chiller is located is
too cold.
•For proper operation, the room temperature should
be equal to or greater than the set temperature of the
wine chiller.
Temperature in the
display is not the
temperature that
was just set.
This is normal.
•After you set the temperature, the display will go
back to showing the actual temperature.
Temperature pads do
not respond
Temperature pads have
been locked.
•To unlock, simply press and hold the RED WINE
and the INTERIOR LIGHT pads at the same time
for 3 seconds. LOC will appear in the display when the
temperature pads have been locked.
Condensation on front
of door
Wine chiller is located in a
high humidity environment.
•Wipe off the condensation with a clean, dry cloth.
•Locate the wine chiller in a lower humidity
environment.
Water on floor behind
wine chiller
Door left open.
•Door is not self-closing. Always make sure that the
door is closed after opening.
•Check to see if a bottle is holding door open.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Wine Chiller Warranty.
All warranty service provided by our Factory Service Centers, or an authorized
®
Customer Care technician. For service call 1-800-361-3400.
Proof of the original purchase date is needed to obtain service under warranty.
For The Period Of:
Camco Will Replace:
One Year
From the date of the
original purchase
Any part of the wine chiller which fails due to a defect in materials or workmanship. During this
limited one-year warranty, Camco will also provide, free of charge, all labour and service to replace
the defective part.
Five Years
From the date of the
original purchase
The compressor if it fails due to a defect in materials or workmanship. This additional four-year
limited warranty does not include service labour charges or service trips to your home.
What Camco Will Not Cover:
■ Service trips to your home to teach you how to use the
■ Incidental or consequential damage to personal property
product.
caused by possible defects with this appliance.
■ Improper installation.
Please read your Use & Care Material:
If you then have any questions about operating the
product, please contact your dealer or our Consumer
Affairs office at the address below, or call toll free:
Camco Inc.
■ Failure of the product if it is abused, misused, or used for
other than the intended purpose or used commercially.
■ Loss of wine due to spoilage.
1-800-361-3400
Consumer Information Service
■ Replacement of house fuses or resetting of circuit
breakers
■ Damage to the product caused by accident, fire, floods
or acts of God.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for use in Canada.
Some provinces do not allow the exclusion or limitation of consequential damages, so the above limitation or exclusion may not
apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from province to province.
To know what your legal rights are in your province, consult your local or provincial consumer affairs office.
Warrantor Camco Inc.
If further help is needed concerning this warranty, write;
Consumer Relations Manager - Camco Inc.
1 Factory Lane, Suite 310, Moncton NB E1C 9M3
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Telephone Numbers.
Problem Solver 1-800-361-3400
For answers call Camco Inc.
Repair Service 1-800-361-3400
Expert Camco repair service is only a phone call away.
Service Contracts 1-800-461-3636
Now you can have trouble-free and suprise-free service for as long
as you own your appliance. While your warranty is still in effect,
you can purchase a CAMCO SERVICE CONTRACT. For one low
fee...just pennies a day...Camco Customer Service will take care of
the repairs your appliance needs - both parts and labour.
Parts and Accessories 1-800-263-0686
Individuals qualified to service their own appliances can have parts
or accessories sent directly to their homes.
Instructions contained in this manual cover procedures to be performed
by any user. Other servicing generally should be referred to qualified
service personnel. Caution must be exercised, since improper servicing
may cause unsafe operation.
Service Satisfaction
If you are not satisfied with the service you receive from Camco,
follow these steps. First, contact the people who serviced your
appliance. Next, if you are still not pleased, write all the
details — including your phone number — to:
Manager, Consumer Relations,
Camco Inc., Suite 310, 1 Factory Lane,
Moncton NB E1C 9M3
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|