Fusionbrands GPS Receiver CA CD800 User Manual

INSTRUCTION MANUAL

MODEL: CA-CD800

A2DP Bluetooth AM/FM/CD/MP3/WMA/SD/USB/AUX/iPod/iPhone Receiver

Download from Www.Somanuals.com. All Manuals Search And Download.

PRECAUTIONS &

MAINTENANCE

GENERAL

QUICK START GUIDE

TUNER REGION SETTING

When the unit is powered up for the ﬁrst time (or the

battery is disconnected or runs ﬂat), you will need to set

your tuner region.

• When cleaning the vehicle, do not get water or cleaning

ﬂuids on the unit.

1. When you press the power button to turn on the unit,

• Do not attempt to open the unit chassis. There are no

user servicable parts or adjustments inside.

[OCEANIA] will be displayed on the LCD screen as the

default Tuner region.

• This unit has been tested with all compatible authentic

iPod/iPhone models under normal expected operating

conditions, free from any pre-existing defects in either the

unit or iPod/iPhone and with unmodiﬁed or “jailbroken”

software.

2. Rotate the Encoder Volume Control to select an option:

OCEANIA (Australia / New Zealand), USA, EUROPE or RUSSIA.

3. Press the Encoder Volume Control to store your selection

and exit to the Tuner mode.

• No Responsibility can be taken for use of the unit other

than under normally expected operating conditions

in conjunction with fully functional and undamaged

iPod/iPhone units which have been manufactured and

authorised by Apple Inc.

If you make the wrong selection, you may not be able to

tune in to your desired stations. This setting can be easily

changed from the SYSTEM MENU – see page 9

SELECTING THE MUSIC SOURCE

• Ensure that only a Genuine USB data sync iPhone/iPod

cable is used for connection to this unit.

Press the source button

sources

to cycle through the following

• When the vehicle’s air conditioner is in use, moisture

may accumulate on the CD Laser lens. This may cause

disc read errors. If this occurs, remove the disc and wait

for the moisture to evaporate.

(if available) – Radio> CD> FRT USB> REAR USB>

SD> BT AUDIO> AUX

BLUETOOTH PAIRING

1. Ensure Bluetooth is enabled on the phone to be

connected to the unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Search for a new Bluetooth device on the phone.

3. Select “FUSION” on the Bluetooth device list.

4. Some devices may require you to enter a PIN.

If prompted, enter “0000” for the PIN.

If you have any questions or require information regarding

installation kits, consult your car audio retailer.

If you are not sure how to install this unit correctly, have it

installed by a qualiﬁed installer.

Please see P12 for detailed Bluetooth operation.

RGB 32K+ SELECTION

The initial colour setting for this unit is Colour Scan. To

quickly enter the 32K+ RGB colour menu, press and hold

the ESC/END/RGB button

You can then rotate the Encoder Volume Control to select

from the following pre-set display colours:

WHITE: GREEN1: GREEN2: GREEN3: AMBER: PINK1:

PINK2: PURPLE1: PURPLE2: BLUE1: BLUE2: USER

COLOUR: ORANGE

Press the ESC/END/RGB button button

your selection.

to conﬁrm

See Page 10 for details on how to set the USER COLOUR

STORE DEMO MODE

When you connect the unit for the ﬁrst time and press the

Mute/Power button

the unit will operate in Demo Mode.

To exit Demo Mode , press the Mute/Power Button again.

See Page 10 to turn Demo Mode off.

DASHBOARD

INSTALLATION

The following illustration shows

typical installation.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING THE SYSTEM

WIRING DIAGRAM

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOVAL/RE-ATTACHMENT BASIC OPERATIONS

OF THE FACE

1. Press the Panel OPEN button.

2. After ﬂipping down the front panel, push it to the right (A),

then draw the left of the front panel outwards (B)

3. To re-attach the face, please complete the above steps in reverse.

1. OPEN

Press this button to ﬂip open and detach the control panel.

2. ENCODER VOLUME CONTROL

Rotate the encoder volume to increase and decrease the volume.

PLEASE NOTE

3. iPod/iPhone INTERNAL/EXTERNAL CONTROL

Press this button to switch between iPod/iPhone control from

either the unit or from the device itself.

4. ENCODER VOLUME CONTROL AUDIO/ENTER FUNCTIONS

a) AUDIO. Press this button to enter the Audio Menu mode.

b) ENTER. In Media playback mode and Menu functions, press this

button to conﬁrm a selection (ENTER).

• If any function does not work, open the front panel & re-close.

• Do not touch the contact pins on the rear of the face as this could

cause contact problems. If the contacts become dirty, please

clean with a soft cloth.

• Petrol and other solvents must not come in contact with the

front face

5. MUTE – POWER ON/OFF

• Please use the supplied plastic case to store the front face when

it is removed from the unit.

a)Press this button to turn Mute ON or OFF

b) Press this button to turn the unit on. Press and hold to turn the unit off.

6. ANSWER KEY

• For security purposes, please ensure that when removed, the

face is stored out of sight if left in the vehicle.

In Bluetooth Handsfree mode:

Download from Www.Somanuals.com. All Manuals Search And Download.

a) Press this button to answer an incoming call.

b) Press & hold for 2 seconds to transfer the call from the

CA-CD800 back to the Mobile Phone.

c) RGB – 32K+ RGB COLOUR. Press and hold this button to access

the 32k+ variable colour setting mode. See Page 9 for more

information

11. BAND/SEARCH

7. NUMERIC BUTTONS

a) In Tuner mode, press this button to cycle through Bands:

FM1, FM2, FM3, AM1 (MW1) or AM2 (MW2).

b) In Media playback mode, press to access the folder / ﬁle search mode.

a) In the Tuner mode, press the Numeric buttons to recall the

preset stations. Press and hold these buttons for 2 seconds to

store stations.

b) In Media playback mode, Press the Numeric buttons to perform

the operations below:

c) In iPod/iPhone playback mode, press this button to access the

iPod/iPhone search functions.

12. MENU

Number

Button

Press to access the system menu. See Page 9 for menu options.

13. TUNE UP/DOWN, FILE & TRACK UP/DOWN

& FAST FORWARD/BACK

Pause/Play

Intro

Repeat

Random

Folder Up Folder Down

8. SUBWOOFER – DIRECT SUBWOOFER LEVEL CONTROL

When a subwoofer is connected; use the DSLC buttons to adjust

the subwoofer level up or down.

9. EQ/DISPLAY

a) TUNE UP/DOWN. In tuner mode, press this button to Auto Seek

to the next station or press and hold this button to manually tune

in to your desired station.

b) FILE & TRACK UP/DOWN. In CD or USB/SD media playback

mode, press these buttons to skip a chapter, track or ﬁle.

c) FAST FORWARD/BACK. In USB/SD media playback mode, press

and hold momentarily to fast forward/rewind.

a) EQ. Press this button to select the preset equaliser settings:

FLAT->POP->USER->DANCE->ROCK->CLASSIC->

JAZZ->VOCAL

b) DISP. Press & hold for 2 seconds.

• In MP3/WMA playback mode, press to display ID3 information: Track

number and elapsed play Time - > File - > Album - > Title - > Artist,

14. SOURCE

Press the SOURCE button

to cycle through the following

sources (if available): Radio> CD> FRT USB> REAR USB>

SD> BT AUDIO> AUX

• In iPod/iPhone playback mode, press to display Album -> Title -> Artist

10. ESC/END/RGB

a) ESC – ESCAPE. Press to quick return previous menu or mode

rather than having to cycle through all of the options in the menu.

b) END – In Bluetooth Handsfree mode, press to END a call or to

Reject an incoming call (before you answer).

Download from Www.Somanuals.com. All Manuals Search And Download.

MID CFQ

Select the Midrange centre frequency: 0.5K /

1.0K / 1.5K / 2.5KHz

AUDIO FUNCTIONS

All Audio functions are easily accessable on the CA-CD800.

TRE

Adjust the Treble level between -7 to +7.

AUDIO MENU. Press the ENCODER VOLUME CONTROL

to access the Audio Menu mode. Then press ENTER or

TRE CFQ

Select the Treble centre frequency: 10.0K /

12.5K / 15.0K / 17.5KHz

TUNE UP

to select the Audio Function to be adjusted,

BAL (Balance)

FAD (Fader)

Adjust the balance between the right and left

speakers from 12R (full right) to 12L (full left).

then rotate the ENCODER VOLUME CONTROL to select

the desired setting. You can always return to the previous

Audio Function by pressing the TUNE DOWN

button.

Adjust the fader between the front and rear

speakers from 12R (full rear) to 12L (full front).

REMINDER

In the AUDIO MENU, or in any menu, you can quickly exit the

menu by pressing the ESC/END/RGB button

(SUBWOOFER)

SW ON/OFF

SW LPF

Turn On or Off the Subwoofer RCA output.

Subwoofer low pass crossover: 80/120/160Hz

In AM mode, turn ON or OFF the Sub output.

QUASI-PARAMETRIC FUNCTION – CFQ ADJUSTMENT

As part of the available Audio Functions, you have the ability

to adjust the Center Frequency of the Bass, Midrange

or Treble controls. This gives you greater control of the

adjustment of these functions by allowing you to select the

preferred Center Frequency to adjust.

SWAM ON/OFF

NOTE

If the Subwoofer RCA output is set to “OFF”, then the SW LPF &

SWAM functions will not be displayed in the Audio Menu.

EQUALISER OPERATION

If you are unsure of which CFQ settings to use, please use

the following Default settings: Bass CFQ 80Hz, Midrange

CFQ 1.5K Hz & Treble CFQ 12.5K Hz

When you activate the Equaliser, the Pre-Set Equaliser settings

override your existing Bass, Midrange & Treble Settings.

Press the Equaliser button repeatedly to cycle through

the following pre-sets: FLAT->POP->USER->DANCE-

>ROCK->CLASSIC->JAZZ->VOCAL

AUDIO FUNCTION ADJUSTMENT:

EBX ON/OFF:

Turn ON or OFF the EBX (Encounter Bass

Xtender) Bass Boost.

To return to the Bass/Midrange/Treble settings that were in use

before the EQ was selected, please select the USER setting.

BAS

Adjust the Bass level between -7 to +7.

BAS CFQ

MID

Select Bass centre frequency: 60 / 80 / 100 / 200Hz

Adjust the Midrange level between -7 to +7.

Download from Www.Somanuals.com. All Manuals Search And Download.

LOC* ON/OFF

SYSTEM MENU

(Local/Distance). Use this setting to Auto Seek to strong

local stations (Local) or all stations regardless of their

strength (Distance).

Press

(MENU) to access the System Menu and press

again to select the item be adjusted, then rotate Encoder

Volume Knob to select a value / option. To exit this menu at

any time, press the ESC/END/RGB button

AREA

STORE (Auto store)

Select your country/region for the tuner:

OCEANIA (Australia/New Zealand); USA; EUROPE;

While in Tuner mode, press the ENCODER VOLUME CONTROL

to activate Auto Store. The six strongest stations of the selected

band will be saved in the preset channels automatically

RUSSIA & press ESC/END/RGB

to save.

CLK (Clock)

RDS ON/OFF

To set the clock, rotate the Encoder Volume Control to set

the hours (Note “A” or “P” will be displayed in the top-right

hand of the LCD display indicating AM or PM if the Clock

is in 12H mode – see below). Press the Encloder Volume

control to select “minutes” then rotate the control to set.

While in Tuner mode, this selection turns On or Off RDS.

RDS Functions are explained in more detail on Page 10. If

RDS is set to OFF, then the RDS Functions indicated below

with an * will not appear in the System Menu

CLK 12H/24H (Clock Format)

Select the time format 12H or 24H

BEEP ON/OFF

Select On or Off to activate button conﬁrmation beep tones.

DEMO ON/OFF

Demo mode is activated when the unit is ﬁrst connected to

the vehicle, but is de-avtivated when the Power Button is

pressed. It can, however, be activated again by pressing the

Power Button. To stop this feature, set Demo Mode to off.

PTY* (Program Type)

Press the ENCODER VOLUME CONTROL to enter program

type, then rotate the ENCODER VOLUME CONTROL to

select the category.

AF* ON/OFF

Turn On or Off the Alternate Frequencies function.

TA* ON/OFF

Turn On or Off the Trafﬁc Announcement function.

REG* ON/OFF

Turn On or Off the Set Region for Alternate Frequencies function

CT* ON/OFF

COL0UR

This unit is equipped with a 32K+ RGB variable colour

display. By rotating the Encoder Volume Control, you

can select the system colour from the following options:

Turn On or Off the CT function.

Download from Www.Somanuals.com. All Manuals Search And Download.

UP or DOWN button, and press it again repeatedly until you select

your desired frequency. After 5 seconds, the display will stop

ﬂashing and the unit will be tuned in to that station.

COLOUR SCAN (default setting); WHITE; GREEN 1; GREEN

2; GREEN 3; AMBER; PINK 1; PINK 2; PURPLE 1; PURPLE

2; BLUE 1; BLUE 2; USER; DEFAULT.

HOW TO STORE YOUR FAVOURITE STATIONS

USER (USER SELECTED COLOUR):

1. Select your preferred Band. Generally you would use FM1 or AM1

to save your favourite stations (6 stations per band). If you need to

store more stations, you can use FM2/3 or AM2 for AM stations.

This allows you to select your choice of display colour from

over 32,000 combinations (32K+). When you select USER in

the colour menu, press the Encoder Volume Control to enter

then rotate to select the intensity of Red, Green & Blue (from

between 0 and 32) to make your own custom colour.

To switch between R (Red), G (Green) and B (Blue) setting

modes, push the TUNE UP button

2. Tune in to your preferred station as per the steps above

3. Press and hold one of the Preset Station Buttons (1-6) for 2

seconds to store the station. The preset number and [SAVED] will

be dislayed on the LCD screen.

Press ESC/END/RGB

your selection.

button once you have completed

TUNE TO A SAVED or PRE-SET STATION

1. Select the relevant BAND

2. Press the Preset Station Number corresponding to your

required Pre-Set station.

RADIO OPERATION

TUNE INTO A RADIO STATION

1. Press the SOURCE button

displayed on the LCD screen.

repeatedly until [RADIO] is

RDS OPERATION

The RDS (Radio Data System) function operates only in areas

with FM stations broadcasting RDS signals. If you tune to an RDS

station, an RDS icon and information about the presenter, station

or program is displayed.

2. Select your preferred listening Band (FM or AM) by pressing

BAND

. There are 3 FM Bands [FM1] [FM2] [FM3] and 2 AM

Bands [AM1] [AM2]. These multiple Bands allow you to store up to

18 FM stations & 12 AM stations in memory (see below).

This unit supports the following RDS features:

3. To search for a radio station, press either the TUNE UP or

(PTY) SELECT PROGRAM TYPE

DOWN

buttons to search for the next station higher than

Before tuning to RDS stations, you can select program type and let

the unit search only for programs of the selected category.

Press the MENU button to enter the System Menu, press

ENTER again to conﬁrm and select PTY type & search for that

style station. Please see a list of PTY Types & descriptions on P20:

the current station frequency or lower than the current frequency.

4. To Manually tune to a radio station, press and hold either the

TUNE UP or DOWN

button until the tuner frequency on

the LCD display starts ﬂashing. You can then release the TUNE

Download from Www.Somanuals.com. All Manuals Search And Download.

(AF) SELECT ALTERNATE FREQUENCIES

iPod/iPhone OPERATION

If the radio signal from the current station is poor, you can turn

on the AF (Alternate Frequency) function to let the unit search

automatically for another station with a stronger signal but with

the same program identiﬁcation as the current station.

This unit is equipped with iPod/iPhone control which

allows you to directly control and charge iPod/iPhones

using the units controls – with display of iPod/iPhone track

information appearing on the unit’s LCD display.

(TA) RECEIVE TRAFFIC ANNOUNCEMENTS

Please read below for more detailed operation.

If you do not want to miss a trafﬁc announcement during music

playback, you can turn on the TA (Trafﬁc Announcement) function.

CONNECTING AN iPod OR iPhone

TA ON:

When there is a trafﬁc announcement; the unit switches

to the tuner mode (regardless of the current mode) and begins to

broadcast the announcement on trafﬁc conditions. When the trafﬁc

announcement is over, the unit will return to the previous mode.

Apple sync cable

(not supplied)

TA OFF Trafﬁc announcement does not cut in.

(REG) REGION FOR AF TUNING

REG ON: Only stations in the current region will be tuned to

automatically.

REG OFF: All stations can be tuned to automatically

Insert the iPod/iPhone data sync cable to the Front USB or

Rear USB socket as shown and the unit will start playing

the iPod/iPhone automatically.

(CT) CLOCK TIME

Turn CT on to set the clock time using RDS data. Turn CT off to set

the clock time manually.

The Rear USB connection is ideal for positioning in a

location such as the glove compartment so your iPod/

iPhone can be stored and charged securely out of sight.

NOTE

Only one iPhone or iPod can be connected to the CA-CD800 at one

time. This means, for example, that if you have an iPod connected

to the Rear USB, then the Front USB must be used for a USB

storage device & vice-versa.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Rotate the Encoder Volume knob to select the desired

selection within the ﬁeld then, press ENTER to conﬁrm.

BASIC SEARCH – PLAYLIST/ARTIST/ALBUM/SONG on

iPod/iPhone

NOTE

Press BAND to browse the iPod/iPhone menu.

When searching for Album, Artist, Song etc, rotate the Encoder

Volume Control clockwise to search from A-Z or anti-clockwise

for Z-A search.

Then rotate the Encoder Volume Control clockwise to and

press ENTER to choose one of the following selections,

then follow the steps below:

RANDOM PLAY

PLAYLIST Rotate the Encoder Volume control to select

Press RDM to cycle between the following modes:

RDM FLD – Plays the current album randomly.

RDM ALL – Plays the whole iPod/iPhone library randomly.

RDM OFF – Turns the Random function off.

iPod/iPhone MASTER CONTROL MODE

your desired Playlist and press ENTER to start play.

ARTIST Rotate the Encoder Volume Control to select your

desired Artist then press ENTER. Rotate the Encoder

Volume Control to then select an Album & press ENTER.

Rotate the Encoder Volume Control again to select a song

within the selected Album.

Press the

button to switch between the two

ALBUM Rotate the Encoder Volume Control to select your

desired Album and press ENTER to select it. Then rotate

the Encoder Volume Control to select a speciﬁc song

within the selected Album.

control options

• Unit control mode: Use the head unit controls to select

Track/Artist/Album/Playlist etc. This is the Default setting.

• iPod/iPhone control mode: Use the iPod/iPhone to select

the Artist/Album/Track etc.

SEARCH FOR FURTHER CONTENT on iPod/iPhone

In addition to the PLAYLIST/ARTIST/ALBUM seach

functions, there are also additional ﬁelds you can search

on your iPod or iPhone – the full list of ﬁelds is as follows:

This mode is useful if you need to sort through a large

amount of Tracks/Albums etc.

NOTE

PLAYLIST/ARTIST/ALBUM/SONG/GENRE/COMPOSER

/ AUDIOBOOK / PODCAST

Please ensure the iPod/iPhone cable is connected correctly to the

USB port and only use an original iPod / iPhone data sync cable.

1. Rotate the Encoder Volume knob to select the desired

search ﬁeld, then press ENTER to conﬁrm.

Download from Www.Somanuals.com. All Manuals Search And Download.

PAIRED NOTIFICATION DISPLAY

When the Bluetooth device is paired with the CA-CD800, the

BLUETOOTH HANDS

FREE & A2DP

STREAMING OPERATION

You can make or receive phone calls with Bluetooth

enabled phones and listen to music from an A2DP

Bluetooth enabled device on the CA-CD800.

Bluetooth Icon

will appear on the LCD display. This should occur

whenever you use the system and the paired device is in range.

HOW TO MAKE A CALL

1. Dial the desired number on the Mobile Phone.

2. Once dialling is in progress, [CALLING] will be displayed

on the LCD screen.

PAIRING A BLUETOOTH DEVICE

When connecting a Bluetooth device for the ﬁrst time, you

will need to pair the device with the unit.

3. When the call is in progress, [TALK] will be displayed on

the LCD along with the elapsed call time.

For most devices, pairing only needs to be done once.

Please follow these steps:

4. The ANSWER

you are in a call.

button will also slowly ﬂash to indicate

1. Ensure Bluetooth is enabled on the phone to be

connected to the unit.

RECEIVING A CALL

1. If there is an incoming call, audio playback from the

current Source will either be Muted or Paused (depending

on the source) and [PHONE IN] will be shown on the

Display along with the Caller ID if it is enabled by the

Phone/Carrier.

2. Search for a new Bluetooth device on the phone (this

may take up to 30 seconds)

3. Select “FUSION” on the Bluetooth device list.

4. Some devices may require you to enter a PIN. If

prompted, enter “0000” for the PIN.

2. Press the ANSWER button

to accept the call.

5. [PAIRING OK] will be displayed on the LCD display if

pairing is successful. The paired device will then connect

to the CA-CD800 Automatically.

3. To Reject the call, press the ESC/END/RGB

and it will not be answered.

button

HOW TO END A CALL

Note on some phones, you may need to select “SET AS

AUTHORISED” or similar to ensure the CA-CD800 will

automatically pair on subsequent usage.

Once in a call, press the ESC/END/RGB

the call.

button to end

Download from Www.Somanuals.com. All Manuals Search And Download.

TO REDIAL A NUMBER

ADVANCED OPERATION

1. During normal head unit operation, press the ANSWER

button to call the last number dialled by the paired mobile

phone. [REDIAL] will be displayed on the LCD screen.

If the device also supports Audio Video Remote Control

Proﬁle (AVRCP), you can control basic playback functions

(eg iPod music) via the head unit.

2. To conﬁrm press either the ANSWER button again or

ENTER on the Encoder Volume Control. [CALLING] will be

displayed on the LCD screen.

1. Follow steps 1 & 2 above as per Basic Operation

2. Press

to start playback. Press again to pause.

3. Press either

to advance to the next track, or

HEAD UNIT / HANDSET CALL TRANSFER

return to the beginning of the track.

You can transfer the call from the car speakers/head unit

back to the phone during a call by pressing theANSWER

button for 2 seconds. [TRANSFER] will be displayed on

the LCD display.

4. Depending on the device, volume adjustment may be

possible from the device. Please ensure it is not set too

high to avoid distortion.

NOTE

Press the ANSWER

button again for 2 seconds to

ID3 type information – Title, Artist, Album etc is not available on

transfer the call back to the head unit.

the LCD screen in Bluetooth A2DP mode.

BLUETOOTH A2DP AUDIO STREAMING

DISCONNECTING THE BLUETOOTH DEVICE

If the connected Bluetooth device supports Advanced

Audio Distribution Proﬁle (A2DP), you can listen to music

stored on the device through the head unit.

1. If the Bluetooth device is paired and you want to disconnect

it from the CA-CD800, press

MENU to enter the System

Menu. Keep pressing until [DISCONN>] is displayed.

BASIC OPERATION

2. Press ENTER on the Encoder Volume Control.

[WAITING] will be displayed on the LCD display, followed

by [DISCONNECTED] when completed.

1. Ensure the Bluetooth device is paired with the head unit.

2. Press the SOURCE button

BT AUDIO source.

repeatedly to select the

RE-CONNECTING THE BLUETOOTH DEVICE

Once paired, the phone should re-connect automatically

every time you use the system. If not, or you have previously

Disconnected the phone, you can manually re-connect it

using the following steps.

3. Open the music player on the device and select & play

your desired track(s)

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Press

MENU to enter the system menu.

USB OPERATION

Keep pressing until [CONNECT>] is displayed.

Insert the USB Device

1. Open the cover marked

2. Press ENTER on the Encoder Volume Control.

[WAITING] will be displayed on the LCD display, followed

by [CONNECTED] when completed.

on the front panel.

2. Insert the USB

device into the USB

socket. The unit will

start playing from

the USB device

automatically.

MEDIA PLAYBACK (CD/

USB/SD/AUX IN)

CD PLAYBACK

You can play the following format CD’s

3. USB storage devices can be

• Commercially Available pre-recorded CD’s

• CD Recordable (CD-R)

• CD Re-writeable (CD-RW)

• MP3 CD’s

used in the Front, Rear USB port of both.

Removal of the USB Device

Before removing the USB device, always remember to

switch to another Source then remove the USB device.

• WMA CD’s

SD CARD OPERATION

NOTE: Please ensure that the disc contains these ﬁle types only.

1. Press OPEN on the front panel to open the ﬂip down panel.

Insert the SD Card

2. Insert a CD with the printed side facing up, then close the

panel. The CD will start playing automatically.

1. Press the OPEN button on the front face.

2. After ﬂipping down the front face, push it to the right then

draw the left of the face outwards to remove it.

• Press

to pause the music playback. Press this button

again to resume music playback. NOTE the volume level

can be adjusted while the unit is paused

• Press the

to skip forward to the beginning of the

next or previous chapter/track.

• Press and hold

through the track.

to fast forward or fast rewind

3. Press

to eject the CD.

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Insert the SD card into the slot with label facing up until

a “CLICK” sound is heard.

ADDITIONAL MEDIA

PLAYBACK FUNCTIONS

(CD/USB/SD)

4. Replace the front panel and the unit will start playing

ﬁles from the card automatically.

PLAY OPTIONS

Removal of the SD Card

MP3/WMA File or Folder Search

Detach the face and press the card until you hear a click

sound. The card is now disengaged. You can then remove

the card.

• Press the BAND

button on front panel access the MP3/

WMA ﬁle search mode.

• Rotate the Encoder Volume Control to search through all

NOTE

Please ensure that USB devices & SD cards contain WMA or MP3

ﬁles only.

folders on the device then pressENTER to make your selection.

• Rotate the Encoder Volume Control to select the desired

track within the previously selected folder and pressENTER

to start it playing

USING AUX-IN

Connect the external device to AUX in jack using a 3.5mm

stereo Aux In cable (not supplied) located on the face, then

press the Source button to select AUX mode.

INTRO PLAY

• During playback, press the INT button (Preset button 2)

to start intro mode. The ﬁrst 10 seconds of all tracks on the

storage media will be played.

Press the Source Button again to select other

source options.

• Once you have found a track you like, press INT again to

resume normal playback.

• To perform Intro Play on ﬁles in the current folder only,

press & hold the INT button while in Intro Mode. [INT) will

be displayed on the LCD along with the folder number.

When you ﬁnd your desired track, press INT Twice to play

the track normally.

REPEAT PLAY

• During playback, press the RPT button (Preset button

Download from Www.Somanuals.com. All Manuals Search And Download.

3) to repeat all tracks on the storage media. [RPT ALL] is

displayed.

DISPLAY FUNCTION

During playback, pressing theDISP button will automatically

cycle through the following information on the ﬁle being

played on the LCD display:

• If you press RPT again, the current track will be repeated

only [RPT TRK] will be displayed

• Pressing RPT again repeats all tracks in the current folder

FOLDER NAME> FILE NAME> ALBUM> TITLE> ARTIST

only [RPT FLD] is displayed

You can also keep pressing the DISP button to ﬁnd the

particular information you are after. Once you have cycled

through all of the available track information by continuing

to press the DISP button, the display will return to the

standard Track Number & Time display. If you stop at this

point, the Automatic Display function is cancelled.

• Once a track is playing in repeat mode, or to check if

Repeat is on, press the RPT button.

• To Cancel Repeat, press and hold the RPT button. The

display will revert back to the standard track number &

time elapsed display.

RANDOM PLAY

STEERING WHEEL

CONTROL INTERFACE

READY

• During playback, press the RDM button (Preset button 4)

to display the current Random Play Mode. If Random Play is

off, [RDM OFF] will be displayed.

This unit includes a 3.5mm Steering Wheel Control

interface. When used in conjunction with an after market

Steering Wheel Control Interface, you can control some

functions of this unit with the Vehicle’s OEM Steering

Wheel Controls.

• Press RDM again to select Random Play for the current

folder only [RDM FLD] is displayed.

• Pressing RDM again selects Random Play for all tracks on

the storage media [RDM ALL] is displayed.

• To cancel Random Play, press RDM to display the current

Random Play mode, then press RDM again to cancel

Random Play

There is even a provision to adjust the Direct Subwoofer Level

Control if the vehicle has Preset Up/Preset Down controls.

5 ^FOLDER

Control Functions (if available on vehicle):

FOLDER SELECT

VEHICLE

CA-CD800

During music playback, use this button to jump to the

previous/next folder on the storage device.

Mode

Source

Download from Www.Somanuals.com. All Manuals Search And Download.

Vol Up

Volume Up

TROUBLESHOOTING

Before going through the check list, please check the wiring

connection diagram. If problems persist, please consult

your Car Audio dealer.

Vol Down

Track Up

Volume Down

Track Up

Track Down

Preset Down

Preset Up

Track Down

Sub Level Down

Sub Level Up

No power or no sound

• Ignition is not on. Turn the Ignition to “accessories”

• Unit is off - press the power button to activate the unit.

• Fuse is blown. Please replace the fuse.

• If the speakers are connected to the speaker outputs,

check the speaker connections.

• If the speakers are connected to ampliﬁer/s only, check

that they are operating correctly.

• If the above solutions do not help, please press the RESET button.

Please visit www.fusionelectronics.com to check for

available interfaces as they become available.

OPTIONAL REMOTE

CONTROL

The CA-REM1 IR Remote Control is available to suit this unit.

Noise in radio broadcasts

Please consult you Car Audio retailer for pricing

and availability.

• Signals are too weak, turn LOC off.

• Check the antenna connection or replace the antenna if

necessary.

Preset stations lost

• Yellow power cable is not correctly wired. Ensure it is

connected to Constant 12V (+).

Unable to Eject Disc

• Press & hold the Eject button

Display shows ERR-1

• The USB or SD device cannot be read. Conﬁrm the device

is formatted to FAT32 (Windows) ﬁle system.

Display shows ERR-3

Download from Www.Somanuals.com. All Manuals Search And Download.

• USB/SD data error. Check to ensure only MP3 or WMA

ﬁles are loaded on the storage devices.

HOW TO RESET THE UNIT

Using the Reset button, you can reset the unit to its default

settings.

Display shows ERR-5

• Communication error. The USB/SD device could be

damaged or corrupted. Please re-format (Fat32 only) or try

a different device.

• The RESET button is located on the main unit (as shown

on the diagram). Press it in with a ballpoint pen or metal

object to activate it.

Bluetooth

• The reset button can be used under the following

circumstances:

• Depending on the Bluetooth version of the device, some

Bluetooth devices may not be able to connect with this head unit.

1. Initial installation of the unit when all wiring is completed.

2. If the unit “freezes”.

3. To RESET the unit to the factory conﬁguration

4. Error indication on the LCD display.

• As Bluetooth is a wireless communication protocol, there

may be times where connection between the device and

head unit is lost or disrupted due to interference or other

signal quality disruptions.

• A2DP playback may be interrupted or playback speed

may vary, or playback may not resume automatically after

making or receiving a call.

• Some Bluetooth enabled mobile phones may only stream

music data. In this case the resultant playback quality

through the head unit will be low.

• Music or noise may be heard for a moment if music

streaming is taking place when starting and ending the call,

• There may be occurrences where music cannot be played

through the head unit even though music is being played

back on the mobile phone.

Download from Www.Somanuals.com. All Manuals Search And Download.

RDS PROGRAM TYPES

& DESCRIPTIONS

PRODUCT

SPECIFICATIONS

Power Supply

Fuse

12V DC (11-16V), Negative Ground

NEWS

News services

15A

AFFAIRS

INFO

SPORT

Politics & current affairs

Special information programs

Sports

Suitable Speaker 4 – 8Ω

Impedance

Power output

RMS output

Pre-AMP output

Aux-In level

MOSFET 50W MAX x 4 channels

22W x 4 @ 10% THD

5.0 V (USB play mode; 1KHZ, 0dB, 10 k Ω load)

≥300mV

EDUCATE

DRAMA

CULTURE

SCIENCE

VARIED

POP M

ROCK M

EASY M

LIGHT M

CLASSICS

OTHER M

WEATHER

FINANCE

CHILDREN

SOCIAL

RELIGION

PHONE IN

TRAVEL

LEISURE

JAZZ M

Education and advanced training

Radio plays and literature

Culture, religion and society.

Science programming

Entertainment programs

Pop music

Subwoofer output 5.0 V (USB play mode; 61KHZ, 0dB, 10 k Ω load)

DAC

1-Bit

iPod/iPhone

Charging

RADIO

Rock Music

USB, 1A

Easy listening music

Light classical music

Calssical music

Special music programs

Weather information

Finance programs

Children’s programs

Social affairs

-FM

Frequency Range 87.5 – 108MHz,

87.5 – 107.9 MHz

50kHz Step (Oceania)

200kHz Step (USA)

50kHz Step (Europe)

87.5 – 108.0 MHz

87.5 – 108 MHz

(FM 1/2) (Russia)

+ 65MHz – 74MHz (FM3) (Russia)

Usable Sensitivity Better than 15dB at S/N 30dB

-AM(MW)

Religion

Talkback

Frequency Range 522 –1620KHz (Oceania)

530 – 1710 KHz (USA)

Travel programs

Leisure

522 – 1620 KHz (Europe)

522 – 1620 KHz (Russia)

Jazz music

Usable Sensitivity Better than 45dB

USB DEVICES:

COUNTRY

NATION M

OLDIES M

FOLK M

DOCUMENT

A-TEST

Country music

National music

USB ﬂash memory USB 1.1 & 2.0 compatible

Old time music

Folk music

BLUETOOTH

Documentary

Output Power

Frequency Band

Typical Range

Standard

Class 2

Alarm Test

2.4000GHz – 2.4835GHz

3 Metres (no obstructions)

Bluetooth 2.0 speciﬁcation

ALARM

Alarm function

Download from Www.Somanuals.com. All Manuals Search And Download.

SUPPORTED

LICENSING

FILE FORMATS

MPEG1/2/2.5

WMA Version

Sampling frequency

MPEG1

Layer 2/3

7/8/9

“Made for iPod and “Made for iPhone” mean that an electronics

accessory has been designed to connect speciﬁcally to iPod or

iPhone respectively, and has been certiﬁed by the developer to

meet Apple performance standards. Apple is not responsible the

operation of this device or its compliance with safety and regulatory

standards. Please note that the use of this accessory with iPod or

iPhone may affect wireless performance. Apple is not responsible

for the operation of the device or its compliance with safety and

regulatory standards.

32/44.1/48 kHz

16/22.05/24 kHz

8/11.025/12KHz

22/32/44/48KHz

MPEG2

MPEG2.5

WMA

Sampling Bit rate

MP3/WMA

ISO9660 Level

Max File/DIR. Count

Max DIR. Depth

Sorting Method

Max File/DIR. Name

ID3

32~320Kbps & VBR

1 / 2 & Joliet (unicode)

999

255

Tree sorting

64Byte

iPod and iPhone are trademarks of Apple inc., registered in the U.S.

and other countries.

V1.0/1.1/2.0/2.3 (Max 32 Byte)

MP3 dir shown in manual as “Folder”

MP3 ﬁle referred to as “Track”.

Maximum length of ﬁle name 28 characters.

Maximum length of directory 16 characters.

Windows Media and the windows logo are trademarks, or registered

trademarks of Microsoft Corporation in the United States and/or

other countries.

Supports

Multi-Session recording.

NOTE: Product speciﬁcations are subject to change without prior notice.

PRODUCT ONLINE:

For your own peace of mind, register your product purchase online

The Bluetooth word mark and logos are owned by the Bluetooth

SIG, inc and any use of such marks by FUSION ELECTRONICS is

under license. Other trademarks and trade names are those of

their respective owners.

at www.fusionelectronics.com

We’ll keep you up to date with any news related to your product or

new accessories to help you get the most from your product.

By registering your product you can be assured that if

the unexpected occurs we’ll have your details and be ready to help.

Download from Www.Somanuals.com. All Manuals Search And Download.

THE FUSION PROMISE OF QUALITY

LIMITED 1 YEAR CONSUMER WARRANTY

FUSION Electronics Limited ‘FUSION’ warrants this FUSION Speaker, Subwoofer, Ampliﬁer Head Unit or genuine FUSION Accessory ‘product’ is free from defects in

material and workmanship, according to the following terms and conditions:

•

The limited warranty for the FUSION product purchased extends to the ﬁrst twelve (12) months beginning on the date of purchase of the product.

The limited warranty extends only to the original consumer purchaser (consumer) of the product and is not assignable or transferable to any subsequent purchaser/end user.

The limited warranty extends only to consumers who purchase the product in one of the countries (or areas) set forth on www. fusionelectronics.com. The limited warranty is

only valid in FUSION’S intended country (or area) of sale of the product.

During the limited warranty period, FUSION or its authorised service network will repair or replace, at FUSION or FUSION’S authorised dealer, any defective product or parts

thereof with new and return the product to the consumer in working condition. No charge will be made to the consumer for either parts or labour in repairing or replacing the

product. All replaced parts and cosmetic parts should be free of defects at the time of shipment and, therefore shall not be covered under these limited warranty terms.

Repaired product will be warranted for the balance of the original warranty period or for ninety (90) days from the date of repair, whichever is longer.

All warranty claims must be accompanied with a copy of this warranty card, and a copy of proof of purchase date.

•

The consumer shall have no coverage or beneﬁts under this limited warranty if any of the following conditions are applicable:

•

The product has been subject to: abnormal use, abnormal conditions, improper storage, exposure to excessive moisture or dampness, exposure to excessive temperature or

other such environmental conditions, unauthorised modiﬁcations, unauthorised connections, unauthorised repair including but not limited to use of unauthorised spare parts

in repairs, misuse, neglect, abuse, accident, alteration, improper installation, acts of God, spill of foods or liquids, maladjustment of customer controls or other acts which are

beyond the reasonable control of FUSION, including deﬁciencies in consumable parts such as fuses, and breakage or damage to antennae unless caused directly by defects in

materials or workmanship, and normal wear and tear of the product.

FUSION was not notiﬁed by the consumer of the alleged defect or malfunction of the product during the applicable limited warranty period.

The product serial number or the accessory date code has been removed, defaced or altered.

The product was used with or connected to an accessory not supplied by FUSION or ﬁt for use with FUSION product, or used in a manner other than its intended use.

•

If a problem develops during the limited warranty period, the consumer should take the following step-by-step procedure:

1. The consumer shall return the product to the place of purchase for repair or replacement processing.

2. The consumer shall also be charged for any parts or labour charges not covered by this limited warranty.

The consumer shall be responsible for expenses related to reinstallation of the product.

3. If the product is returned to FUSION after the expiration of the warranty period, FUSION’s normal service policies shall apply and the consumer will be charged

accordingly.

THE BENEFITS CONFERRED BY THIS LIMITED WARRANTY APPLY TO THE EXTENT THAT THEY ARE NOT SUPERCEDED BY ANY OTHER RIGHTS AND REMEDIES UNDER ANY

APPLICABLE LEGISLATION THAT CANNOT BE EXCLUDED. OTHERWISE, TO THE EXTENT PERMITTED BY LAW, ANY IMPLIED WARRANTY IS EXCLUDED AND THE FOREGOING

WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. TO THE EXTENT PERMITTED BY LAW,

FUSION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OR A LOSS OF ANTICIPATED BENEFITS OR PROFITS, OUT OF USE OR INABILITY TO USE THE

PRODUCT.

•

Some states in America do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you

speciﬁc legal rights which may vary from state to state.

FUSION neither assumes nor authorises any authorised service centre or any person or entity to assume for it any other obligation or liability beyond that which is expressly

provided for in this warranty.

All warranty information, product features and speciﬁcations are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

AUSTRALIAN CONSUMERS

LIMITED 1 YEAR CONSUMER WARRANTY

Fusion Electronics Pty Limited, Unit 21/130 Kingston Road, Underwood, Queensland, 4119, Australia.

EMAIL: [email protected] PHONE: 1300 736 012

THE FUSION PROMISE OF QUALITY LIMITED 1 YEAR CONSUMER WARRANTY

This warrant is given in addition to other rights and remedies available to the consumer under Australian Consumer Law. In addition to the Fusion Warranty our

goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for

compensation for any others reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of accept

able quality and the failure does not amount to a major failure.

FUSION Electronics Limited ‘FUSION’ warrants this FUSION Product including Speaker, Subwoofer, Ampliﬁer Head Unit or genuine FUSION Accessory ‘product’ is free from

defects in materials and workmanship, in accordance with the following terms and conditions:

•

The limited warranty for the FUSION product purchased is only available for (12) months after the date of purchase.

The limited warranty extends only to the original consumer of the product and may not be assigned or transferred to any other person or consumer without Fusion’s prior written

consent being provided.

•

During the limited warranty period, FUSION or its authorised service network will repair or replace any defective or faulty product or parts at its own cost.

Repaired or replaced product will be warranted for the balance of the original warranty period or for ninety (90) days after the date of repair, whichever is longer.

All warranty claims must be notiﬁed to Fusion or its authorised Dealer in writing during the warranty period accompanied with a copy of this warranty card, proof of purchase

date and the product with an intact and unaltered serial number or accessory date code.

This Warranty will not apply if:

The consumer causes the Product to be of unacceptable quality or fails to take steps to prevent the Product from becoming of unacceptable quality and/or it is damaged by abnormal

use. Examples of goods becoming of unacceptable quality or of abnormal use by the consumer include;

•

Storage of product under improper conditions.

Exposure to excessive moisture or dampness.

Exposure to excessive temperature extremes or other adverse environmental conditions.

Unauthorised modiﬁcations of product, connections or otherwise unauthorised repairs including, but not limited, to the use of unauthorised parts in the repair of products

Improper use of or installation of, or interference with, product adjustments or controls and or including antenna breakage or damage due to misuse

Damage caused by consumables or by electricity supply.

Acts of god (force majeure), exposure of product to food spills, or any other type of ﬂuid ingress

Using the product in a way for which was not intended to be used or connecting it to an accessory not supplied by, speciﬁed by, or authorised by Fusion

Any other abnormal use of or conduct causing product to become of unacceptable quality

Other exclusions;

•

This warranty extends to the repair or replacement of Fusion product only and the consumer is responsible for any expenses relating to the removal or installation of the product

or related services including the cost of delivering the product to Fusion or its authorised dealer.

Repair work conducted by Fusion after this warranty has expired or if this warranty for any other reason this Fusion warranty does not apply is subject to Fusion’s normal service

policies and Fusion charges for labour and material may apply.

•

This is a manufacturers warranty provided to consumers of Fusion products. Variations to this warranty may only be made by Fusion and will be notiﬁed to the customer in writing

or issued on the Fusion website. Fusion Dealers, agents and authorised dealers are not authorised to make changes or vary this Fusion warranty.

All warranty information, product features and speciﬁcations are subject to change without notice.

•

Fusion is not responsible for replacing or the cost of replacing any consumer data lost occurring either due to equipment failure, or during the repair and replacement process.

Download from Www.Somanuals.com. All Manuals Search And Download.

FRANÇAIS

LA PROMESSE DE QUALITE FUSION

GARANTIE LIMITEE 1 AN

FUSION Electronics Limited, « FUSION », garantit ce haut-parleur, caisson de basses, ampliﬁcateur ou accessoire FUSION authentique contre tout défaut de matériaux

et de main-d’œuvre conformément aux conditions générales énoncées ci-après :

•

La garantie limitée couvrant le produit FUSION acheté est valable douze (12) mois à compter de la date d’achat dudit produit.

Seul l’acheteur initial (client) du produit peut faire valoir la garantie limitée, qui n’est ni cessible ni transférable à un quelconque autre acheteur/utilisateur ﬁnal.

Seuls les clients achetant le produit dans l’un des pays (ou régions) listés sur www.fusionelectronics.com peuvent faire valoir la garantie limitée. La garantie limitée n’est

valable que dans les pays (ou régions) de vente du produit prévus par FUSION.

•

Pendant la période de garantie limitée, FUSION ou son réseau de SAV agréé répare ou remplace, à la discrétion de FUSION ou du distributeur FUSION agréé, tout produit

défectueux ou pièce du produit en question par un produit ou pièce neuf et retourne le produit en état de marche au client. Aucuns frais ne sont facturés au client pour les

pièces ou la main-d’œuvre en cas de réparation ni pour le remplacement du produit. Toutes les pièces remplacées et toutes les pièces d’habillement devraient être exemptes

de défauts au moment de l’expédition et ne seront donc pas couvertes par la présente garantie limitée.

•

Les produits réparés sont garantis pendant la durée restante de la garantie initiale ou pendant quatre-vingt-dix (90) jours à compter de la date de la réparation, si cette durée

est supérieure à la durée de garantie restante.

Toutes les réclamations au titre de la garantie doivent être envoyées avec une copie de cette carte de garantie et une copie de la preuve de la date d’achat.

La garantie limitée est annulée si :

•

Le produit : a été utilisé de manière ou dans des conditions anormales, rangé de manière inappropriée, exposé à une humidité ou température excessive ou à des conditions

ambiantes similaires, modiﬁé sans autorisation, connecté de manière non autorisée, réparé de manière non autorisée y compris, sans que cela soit limitatif, en utilisant des

pièces de rechange non agréees, soumis à un usage abusif, négligé, endommagé accidentellement, altéré, mal installé, endommagé dans une catastrophe naturelle, par de

la nourriture ou des liquides, du fait d’un mauvais ajustement des commandes utilisateur ou par tout acte échappant à la volonté de FUSION, y compris la défaillance des

consommables tels que les fusibles et la rupture ou l’endommagement des antennes, à moins que cela ne soit la conséquence directe d’un défaut de matériaux ou de main-

d’œuvre, et a subi une usure normale.

•

FUSION n’a pas été informée par le client du défaut ou de la défaillance présumé du produit pendant la durée de garantie limitée applicable.

Le numéro de série du produit ou le code de date de l’accessoire a été effacé, dégradé ou altéré.

Le produit était utilisé avec ou connecté à un accessoire non fourni par FUSION ou incompatible avec le produit FUSION, ou a été utilisé pour un usage autre que celui pour

lequel il est prévu.

En cas de problème pendant la durée de la garantie limitée, le client devra suivre la procédure suivante :

1. Le client doit retourner le produit au lieu d’achat pour réparation ou remplacement.

2. Le client doit assumer tous les frais de pièces ou de main-d’œuvre non couverts par la garantie limitée. Le client doit assumer le coût de réinstallation du produit.

3. Si le produit est retourné à FUSION après expiration de la période de garantie, la politique de SAV habituelle de FUSION s’applique et le client sera facturé en conséquence.

LES PRESTATIONS AU TITRE DE CETTE GARANTIE LIMITEE SONT ASSUREES DANS LA MESURE OU ELLES NE SONT PAS REMPLACEES PAR UN QUELCONQUE AUTRE DROIT

OU RECOURS CONFORMEMENT A TOUTE LOI APPLICABLE NE POUVANT PAS ETRE EXCLUE. DANS TOUS LES AUTRES CAS ET DANS LA MESURE PERMISE PAR LA LOI, TOUTE

GARANTIE IMPLICITE EST EXCLUE ET LA GARANTIE DECRITE PRECEDEMMENT EST LE SEUL ET UNIQUE RECOURS DE L’ACHETEUR ET REMPLACE TOUTES LES AUTRES

GARANTIES, QU’ELLES SOIENT EXPRESSES OU IMPLICITES. DANS LA MESURE PERMISE PAR LA LOI, FUSION NE PEUT ETRE TENUE POUR RESPONSABLE DE TOUT DOM-

MAGE ACCESSOIRE OU INDIRECT NI DE TOUTE PERTE D’AVANTAGES OU DE PROFITS ESCOMPTES RESULTANT DE L’UTILISATION DU PRODUIT OU DE L’IMPOSSIBILITE DE

L’UTILISER.

•

FUSION n’autorise aucun SAV agréé, personne ou entité à assumer en son nom des obligations ou une responsabilité autres que celles expressément énoncées dans la

présente garantie.

•

Toutes les informations de garantie, caractéristiques et spéciﬁcations produit peuvent être modiﬁées sans notiﬁcation préalable.

Download from Www.Somanuals.com. All Manuals Search And Download.

ESPANOL

LA PROMESA DE CALIDAD DE FUSION

GARANTÍA LIMITADA DEL CONSUMIDOR DE 1 AÑO

FUSION Electronics Limited, “FUSION”, garantiza que este altavoz, subwoofer, ampliﬁcador FUSION o “producto” accesorio auténtico de FUSION no presenta

defectos materiales ni de fabricación, según lo estipulado por los siguientes términos y condiciones:

FUSION Electronics Limited, “FUSION”, garantiza que este altavoz, subwoofer, ampliﬁcador FUSION o “producto” accesorio auténtico de FUSION no presenta defectos materiales

ni de fabricación, según lo estipulado por los siguientes términos y condiciones:

•

La garantía limitada para los productos FUSIONadquiridos se extiende durante los primeros doce (12) meses a partir de la fecha de compra del producto.

La garantía limitada se aplica solo al comprador consumidor original (consumidor) del producto y no es endosable ni transferible a ningún comprador/usuario ﬁnal posterior.

La garantía limitada se aplica únicamente a los consumidores que adquieran el producto en uno de los países (o regiones) expuestos en www. fusionelectronics.com. La

garantía limitada solo es válida en los países (o regiones) en los que FUSION tenga intención de vender el producto.

Durante el periodo de garantía limitada, FUSION o su red de reparación autorizada reparará o sustituirá en FUSION o en un concesionario de FUSION autorizado todo producto

defectuoso o piezas del mismo con otros nuevos y devolverá el producto al consumidor en condiciones de utilizarlo. No se le cobrarán al consumidor ninguna pieza ni mano de

obra necesarios para reparar o sustituir el producto. Ninguna pieza sustituida ni pieza embellecedora debería presentar defectos en el momento de su envío y, por lo tanto, no

estará cubierta en los presentes términos de garantía limitada.

•

La garantía del producto reparado se extenderá durante el tiempo restante del periodo original de garantía o durante noventa (90) días a partir de la fecha de reparación,

escogiéndose la opción de mayor duración.

Todas los reclamos sobre la garantía han de ir acompañados de una copia de la presente tarjeta de garantía y una copia justiﬁcante de la fecha de compra.

El consumidor no tendrá la cobertura ni beneﬁcios expuestos en la presente garantía limitada si se da cualquiera de las siguientes condiciones:

•

El producto ha sido objeto de: uso anormal, condiciones anormales, almacenamiento inadecuado, exposición a una humedad excesiva, exposición a una temperatura excesiva

u otras condiciones ambientales similares, modiﬁcaciones no autorizadas, conexiones no autorizadas, reparaciones no autorizadas, incluyendo pero sin limitarse a, uso de

piezas no autorizadas en reparaciones, uso indebido, abandono, abuso, accidente, alteración, instalación incorrecta, causa de fuerza mayor, derrame de alimentos o líquidos,

ajuste incorrecto de los controles del cliente u otros actos que estén más allá del control de FUSION, incluida la falta de piezas consumibles tales como fusibles, y la rotura o

daños ocasionados a las antenas, salvo que hayan sido causados directamente por materiales o fabricación defectuosos, y el desgaste natural por el uso.

El consumidor no le notiﬁcó a FUSION el supuesto defecto o disfunción del producto durante el periodo de aplicación de la garantía limitada.

Se ha eliminado, borrado o modiﬁcado el número de serie del producto o el código de fecha del accesorio.

•

El producto se utilizó con o se conectó a un accesorio no suministrado por FUSION o no adecuado para utilizar con productos FUSION, o se utilizó de una forma diferente a su

uso indicado.

Si surge un problema durante el periodo de validez de la garantía limitada, el consumidor debe seguir paso a paso el siguiente procedimiento:

1. El consumidor devolverá el producto al lugar de compra para proceder a su reparación o sustitución.

2. El consumidor habrá de pagar toda pieza o mano de obra que no cubra la presente garantía limitada. El consumidor será responsable de los gastos asociados a la reinstalación

del producto.

3. Si se devuelve el producto a FUSION después del vencimiento del periodo de garantía, se aplicará la política normal de reparación de FUSION y se le cobrará al consumidor de

acuerdo con ésta.

LOS BENEFICIOS CONFERIDOS POR LA PRESENTE GARANTÍA LIMITADA SON DE APLICACIÓN SIEMPRE Y CUANDO NO SEAN SUSTITUIDOS POR OTROS DERECHOS Y

RECURSOS BAJO OTRA LEGISLACIÓN QUE NO SE PUEDA EXCLUIR. DE LO CONTRARIO, Y HASTA EL LÍMITE PERMITIDO POR LA LEY, SE EXCLUYE TODA GARANTÍA IMPLÍCITA,

Y LA GARANTÍA ANTERIORMENTE EXPUESTA ES EL RECURSO ÚNICO Y EXCLUSIVO DEL COMPRADOR, Y REVOCA CUALQUIER OTRA GARANTÍA, YA SEA EXPLÍCITA O IMPLÍCITA.

HASTA EL LÍMITE PERMITIDO POR LA LEY, FUSION NO SE RESPONSABILIZA DE DAÑOS INCIDENTALES NI EMERGENTES NI DE PÉRDIDAS DE BENEFICIOS O GANACIAS

ANTICIPADAS RESULTANTES DEL USO O DE LA INCAPACIDAD PARA UTILIZAR EL PRODUCTO.

•

Algunos estados en EE.UU. no permiten la exclusión o limitación de los daños emergentes, por lo que puede que la limitación y exclusión anteriores no sea de aplicación para

usted. Esta garantía le otorga derechos especíﬁcos que pueden variar de un estado a otro.

FUSION no asume ni autoriza a ningún centro autorizado ni persona ni entidad a aceptar ninguna otra obligación o responsabilidad más allá de lo expuesto expresamente en

esta garantía.

Toda la información de garantía, características y especiﬁcaciones del producto están sujetas a cambios sin previo aviso.

Download from Www.Somanuals.com. All Manuals Search And Download.

ITALIANO

LA PROMESSA DI QUALITÀ FUSION

GARANZIA LIMITATA DI 1 ANNO PER IL CONSUMATORE

FUSION Electronics Limited ‘FUSION’ garantisce questo altoparlante, subwoofer, ampliﬁcatore

materiali e di fabbricazione,

accessorio originale FUSION (‘il prodotto’) da difetti dei

fatte salve le seguenti clausole:

•

La garanzia limitata per il prodotto FUSION acquistato vale per i primi dodici (12) mesi dalla data di acquisto del prodotto stesso..

La garanzia limitata vale solo per l’acquirente originale (‘il consumatore’) del prodotto e non può essere assegnata né trasferita a successivi acquirenti o utenti ﬁnali.

La garanzia limitata vale solo per il consumatore che acquisti il prodotto in uno dei Paesi (o delle aree) elencati presso www.fusionelectronics.com. La garanzia limitata

è valida solo nel Paese (o nell’area) in cui il prodotto è stato destinato da FUSION alla vendita.

•

Durante il periodo di validità della garanzia limitata, FUSION o la sua rete di assistenza autorizzata s’impegna a riparare o sostituire, presso FUSION o un suo rivenditore

autorizzato, il prodotto difettoso o le parti difettose di un prodotto e di restituire il prodotto al consumatore in buono stato. Non sarà addebitato al consumatore alcun

costo di parti o manodopera incorso da FUSION per la riparazione o sostituzione del prodotto. Tutte le parti funzionali e decorative che siano state sostituite s’intendono

prive di difetti al momento della consegna e pertanto non sono coperte a loro volta dalle clausole della presente garanzia limitata.

Il prodotto riparato sarà garantito per il periodo di validità restante della garanzia o per novanta (90) giorni dalla data di riparazione, qualora la garanzia originale debba

scadere entro meno di novanta (90) giorni.

•

Tutte le richieste d’intervento in garanzia devono essere accompagnate da una copia di questo cartoncino e della prova di acquisto completa di data.

La garanzia limitata viene a decadere in presenza di una o più delle seguenti situazioni:

•

Il prodotto sia stato soggetto a uso anomalo, condizioni anomale, stoccaggio anomalo, esposizione a umidità eccessiva, esposizione a temperature o altre

condizioni ambientali al di fuori dai parametri di utilizzo, modiﬁche non autorizzate, collegamenti non autorizzati, riparazioni non autorizzate, ivi compreso – ma

senza limitazione – l’uso di parti di ricambio non autorizzate in tali riparazioni, cattivo uso, negligenza, abuso, incidenti, modiﬁche, installazione scorretta, eventi

riconducibili a cause di forza maggiore, versamernto di liquidi o cibi, cattiva regolazione dei comandi da parte del cliente o altre azioni che siano al di fuori del

ragionevole controllo di FUSION, compreso il malfunzionamento di materiali di consumo quali i fusibili, e lesioni o danni alle antenne, a patto che non siano causati

direttamente da difetti di materiali o di fabbricazione, come pure il normale deterioramento del prodotto.

•

FUSION non sia stata informata dal consumatore del supposto difetto o malfunzionamento del prodotto entro la scadenza della garanzia limitata.

Il numero di serie del prodotto o il codice di data di un accessorio sia stato rimosso, reso illeggibile o alterato.

Il prodotto sia stato usato insieme a o in collegamento con un accessorio non fornito da FUSION o inadatto all’uso con il prodotto FUSION, o sia stato utilizzato per

scopi diversi da quello a cui è destinato.

Qualora si presenti un problema prima della scadenza della garanzia limitata, il consumatore è tenuto a:

1. Restituire il prodotto al punto vendita perché venga riparato o se ne disponga la sostituzione.

2. Farsi carico dei costi di parti e manodopera che non siano coperti da questa garanzia limitata. Farsi carico delle spese relative alla reinstallazione del prodotto..

3. Se il prodotto viene restituito a FUSION dopo la scadenza della garanzia, FUSION farà valere le sue normali clausole di assistenza e addebiterà al consumatore le

spese del caso.

LE CLAUSOLE DI QUESTA GARANZIA LIMITATA VIGONO NELLA MISURA IN CUI NON RISULTINO INCOMPATIBILI CON ALTRI DIRITTI O TUTELE PREVISTI DALLE LEGGI

VIGENTI CUI QUESTA GARANZIA NON PUÒ SOSTITUIRSI. AD ESCLUSIONE DI QUANTO SUINDICATO, ED ENTRO I LIMITI CONSENTITI DALLA LEGGE, LA PRESENTE

GARANZIA FA DECADERE QUALSIASI GARANZIA IMPLICITA O ESPLICITA E DIVIENE L’UNICA ED ESCLUSIVA FORMA DI TUTELA DELL’ACQUIRENTE. ENTRO I LIMITI

CONSENTITI DALLA LEGGE, FUSION NEGA QUALSIASI RESPONSABILITÀ PER DANNI DIRETTI O INDIRETTI COME PURA PER LA PERDITA DI BENEFICI O PROFITTI

AUSPICATI, ANCHE QUALORA TALI DANNI POSSANO ESSERE RICONDOTTI ALL’USO DEL PRODOTTO O ALL’IMPOSSIBILITÀ DI SERVIRSI DI ESSO.

•

FUSION non invita né autorizza che un centro di servizio autorizzato o un qualsiasi altro individuo o entità si faccia carico di obblighi o responsabilità che vadano oltre

quelli espressamente previsti dalle clausole della presente garanzia.

•

Tutte le informazioni di garanzia, le caratteristiche e le speciﬁche di prodotto sono soggette a modiﬁche senza preavviso.

Download from Www.Somanuals.com. All Manuals Search And Download.

DEUTSCH

DAS QUALITÄTSVERSPRECHEN VON FUSION

EINJÄHRIGE BESCHRÄNKTE GEWÄHRLEISTUNG

FUSION Electronics Limited „FUSION“ garantiert, dass dieser Lautsprecher, Subwoofer oder Verstärker bzw. dieses Originalzubehör von FUSION frei von Material- oder

Verarbeitungsfehlern ist und gibt eine Gewährleistung unter den folgenden Bedingungen:

•

Die beschränkte Gewährleistung für das FUSION-Produkt beschränkt sich auf die ersten zwölf (12) Monate ab Kaufdatum des Produkts.

Die beschränkte Gewährleistung gilt nur für den Erstkäufer (Kunde) des Produkts und ist nicht auf nachfolgende Käufer bzw. Endverbraucher übertragbar.

Die beschränkte Gewährleistung gilt nur für Kunden, die das Produkt in einem der Länder/Gebiete gekauft haben, die unter www.fusionelectronics.com aufgelistet sind.

Die beschränkte Gewährleistung ist nur im von FUSION vorgesehen Verkaufsland/-gebiet gültig.

•

Während der beschränkten Gewährleistungsdauer repariert FUSION oder sein autorisierter Fachhändler defekte Produkte oder deren Komponenten oder ersetzt diese

durch neue Produkte oder Komponenten und gibt das Produkt funktionstüchtig an den Kunden zurück. Dem Kunden werden weder Arbeitszeit noch Ersatzteile für die

Reparatur bzw. den Ersatz des Produkts in Rechnung gestellt. Alle ersetzten und kosmetische Teile sollten zum Zeitpunkt des Versands frei von Defekten sein und sind

deshalb nicht durch diese beschränkten Gewährleistung abgedeckt.

•

Die Gewährleistungsfrist für reparierte Produkte erstreckt sich über den verbliebenen Zeitraum der ursprünglichen Gewährleistungsfrist oder beträgt neunzig (90) Tage

ab Reparaturdatum, je nach dem welcher Zeitraum länger ist.

Für alle Gewährleistungsansprüche muss eine Kopie dieses Gewährleistungsscheins sowie ein Beleg des Kaufdatums vorgelegt werden.

Unter den folgenden Bedingungen hat diese beschränkte Gewährleistung keine Gültigkeit:

•

Unsachgemäße Verwendung des Produkts, unsachgemäße Bedingungen, unsachgemäße Lagerung, übermäßige Feuchtigkeit, übermäßige Temperaturen oder

andere unangemessene Umgebungsbedingungen, nicht autorisierte Modiﬁkationen, nicht autorisierte Anschlüsse, nicht autorisierte Reparaturen, einschließlich

(ohne Anspruch auf Vollständigkeit) Verwendung nicht autorisierter Ersatzteile, unsachgemäßer Gebrauch, Vernachlässigung, Missbrauch, Unfall, Abänderung,

unsachgemäße Installation, höhere Gewalt, Auslaufen von Lebensmitteln oder Flüssigkeiten, unsachgemäße Einstellung der Bedienungselemente oder andere von

FUSION nicht vorhersehbarer Vorfälle wie defekte Verbrauchsteile (z. B. Sicherungen) oder defekte oder beschädigte Antennen, die nicht direkt auf Material- oder

Verarbeitungsfehlern zurückzuführen sind, sowie normaler Verschleiß des Produkts.

•

FUSION wurde während der entsprechenden Gewährleistungsfrist nicht vom Kunden über den angeblichen Defekt bzw. die Fehlfunktion informiert.

Die Seriennummer des Produkts oder der Zubehörcode wurde entfernt, ausgestrichen oder abgeändert.

Das Produkt wurde mit einem Zubehörteil verwendet oder an ein Zubehörteil angeschlossen, das nicht von FUSION geliefert bzw. für die Verwendung mit dem Produkt

von FUSION nicht geeignet war oder unsachgemäß verwendet wurde.

Wenn während der beschränkten Gewährleistungsfrist ein Problem auftritt, muss der Kunde die folgenden Schritte befolgen:

1. Der Kunde muss das Produkt zur Reparatur bzw. zum Umtausch zur Verkaufsstelle zurückbringen.

2. Dem Kunden werden alle Teile bzw. Arbeitskosten berechnet, die nicht von dieser beschränkten Gewährleistung abgedeckt sind. Der Kunde trägt die Kosten für den

Neueinbau des Produkts.

3. Wenn das Produkt nach Ablauf der Gewährleistungsfrist an FUSION zurückgegeben wird, gelten die normalen Reparaturbedingungen von FUSION, und der Kunde trägt

die entsprechenden Kosten.

DIESE BESCHRÄNKTE GEWÄHRLEISTUNG GILT, SOWEIT ANDERE RECHTE UND RECHTSMITTEL DES ANWENDBAREN RECHTS, DIE NICHT AUSGESCHLOSSEN WERDEN

KÖNNEN, AN IHRE STELLE TRETEN. SOWEIT GESETZLICH ZUGELASSEN, IST JEDE ANDERE STILLSCHWEIGENDE GEWÄHRLEISTUNG AUSGESCHLOSSEN.

DIESE GEWÄHRLEISTUNG IST DAS EINZIGE RECHTSMITTEL DES KÄUFERS UND ERSETZT ALLE ANDEREN AUSDRÜCKLICHEN ODER STILLSCHWEIGENDEN

GEWÄHRLEISTUNGEN. SOWEIT GESETZLICH ZUGELASSEN, HAFTET FUSION NICHT FÜR NEBEN- UND FOLGESCHÄDEN ODER DEN VERLUST VORAUSSICHTLICHER

VORTEILE ODER GEWINNE INFOLGE DES GEBRAUCHS ODER AUSFALLS DES PRODUKTS.

•

Weder FUSION selbst noch andere autorisierte Service-Center bzw. Personen oder juristische Personen sind befugt, andere, als die in dieser Gewährleistung

ausdrücklich aufgeführten Verpﬂichtungen oder Haftungen zu übernehmen..

•

Alle Gewährleistungsinformationen, Produktmerkmale und technischen Daten können sich ohne Vorankündigung ändern.

Download from Www.Somanuals.com. All Manuals Search And Download.

PYCCKИЙ

ОБЕЩАНИЕ КАЧЕСТВА ОТ ФИРМЫ FUSION

ОГРАНИЧЕННАЯ ПОТРЕБИТЕЛЬСКАЯ ГАРАНТИЯ НА 1 ГОД

Фирма FUSION Electronics Limited (‘FUSION’) гарантирует, что эта акустическая система, сабвуфер, услитель или подлинные дополнительные ‘приспособления’

фирмы FUSION не будут иметь дефектов материала и изготовления согласно следующим условиям:

•

Ограниченная гарантия на купленный продукт фирмы FUSION действует в течечние первых двенадцати (12) месяцев, начиная с даты покупки продукта.

Ограниченная гарантия распространяется только на первичного потребителя-покупателя (покупателя) продукта и не может быть передана или уступлена

никакому последующему покупателю/конечному пользователю.

•

Ограниченная гарантия распрстраняется на покупателей, которые купили продукт в одной из стран (или регионов), указанных на www. fusionelectronics.com.

Ограниченная гарантия действительна только в стране (или регионе), в которой данный продукт предназначен фирмой FUSION для продажи.

В течение срока ограниченной гарантии, фирма FUSION или уполномоченная ею сеть обслуживания отремонтирует или заменит новым в фирме FUSION

или у уполномоченного дилера фирмы FUSION любой неисправный продукт или его детали и возвратит продукт покупателю в рабочем состоянии. С

покупателя не будет взята плата ни за детали, ни за работу, ни за замену продукта Все замененные и косметические детали должны быть без дефектов во

время отправки, и поэтому на них не распространяются условия этой ограниченной гарантии.

•

Отремонтированный продукт подлежит гарантии на оставшийся срок первичной гарантии или на девяносто (90) дней с даты ремонта, в зависимости от того,

что действует дольше.

Все гарантийные претензии должны сопровождаться копией этого гарантийного формуляра и копией потверждением даты покупки.

Покупатель не пользуется льготами по этой ограниченной гарантии, если могут быть применены любые из следующих условий:

•

Продукт был подвергнут: неправильному использованию, несоотвествующим условиям, неправильному хранению, воздействию чрезмерной сырости

или влажности, воздействию чрезмерной температуры или других условий окружающей среды, несанкционированным модификациям, неразрешенным

подключениям, несанкционированному ремонту, включая, но неограничиваясь использованием несанкционированных запасных частей при ремонте,

неправильным использованием, небрежностью, злоупотреблением, аварией, переделкой, неправильной установкой, стихийными бедствиями, пролитой едой

или жидкостями, неправильной регулировкой покупателем или другими действиями, которые находятся вне разумного контроля фирмы FUSION, включая

дефекты используемых деталей, таких как плавкие предохранители, поломку или повреждение антенны, если только они не вызваны непосредственно

дефектами материала и изготовления, и обычный износ проддукта.

•

Фирма FUSION не была информирована потребителем о заявленном дефекте или неисправности продукта в течение соотвестветствующего срока

ограниченной гарантии.

Серийный номер или код даты приспособлений был удален, поврежден или изменен.

Продукт использовался или был соединен с приспособлением, не поставляемым фирмой FUSION, или не предназначенным для использования с продуктами

FUSION, или использовался иным способом, чем тот, для которого он был предназначен.

•

Если в период ограниченной гарантии возникла проблема, то покупатель должен последовательно выполнить следующие действия:

1. Покупатель должен возвратить продукт в место покупки для осуществления ремонта или замены.

2. Покупатель должен оплатить любые детали или работу, на которую не распространяется эта ограниченной гарантией. Покупатель будет нести

отвественность за расходы, свзанные с повторной установкой продукта.

3. Если продукт был возвращен фирме FUSION после истечения гарантийного срока, для него будут применимы обычные условия обслуживания фирмы

FUSION, и с покупателя будет взята соотвествующая плата.

ЛЬГОТЫ, ПРЕДОСТАВЛЯЕМЫЕ ЭТОЙ ОГРАНИЧЕННОЙ ГАРАНТИЕЙ, ПРИМЕНИМЫ В ТАКОЙ СТЕПЕНИ, ЧТО ОНИ НЕ МОГУТ БЫТЬ ЗАМЕНЕНЫ КАКИМИ-

ЛИБО ДРУГИМИ ПРАВАМИ И СРЕДСТВАМИ СОГЛАСНО ЛЮБОМУ ЗАКОНДАТЕЛЬСТВУ, КОТОРЫЕ НЕЛЬЗЯБЫБЫЛО ИСКЛЮЧИТЬ. ДРУГИМ СЛОВАМИ,

В ПРЕДЕЛАХ ЗАКОНА, ИСКЛЮЧАЕТСЯ ЛЮБАЯ ПОДРАЗУМЕВАЮЩАЯСЯ ГАРАНТИЯ, И ВЫШЕУПОМЯНУТАЯ ГАРАНТИЯ ЯВЛЯЕТСЯ ДЛЯ ПОКУПАТЕЛЯ

ЕДИНСТВЕННЫМ И ИСКЛЮЧИТЕЛЬНЫМ СРЕДСТВОМ ЗАЩИТЫ ПРАВ ВМЕСТО ВСЕХ ДРУГИХ ГАРАНТИЙ, ВЫРАЖЕННЫХ ИЛИ ПОДРАЗУМЕВАЕМЫХ.

В РАМКАХ ЗАКОНА, ФИРМА FUSION НЕ НЕСЕТ ОТВЕСТВЕННОСТИ ЗА ПОБОЧНЫЕ ИЛИ КОСЕННЫЕ УБЫТКИ ИЛИ ПОТЕРЮ ОЖИДАЕМОЙ ВЫГОДЫ,

ВСЛЕДСТВИЕ ИСПОЛЬЗОВАНИЯ ИЛИ НЕВОЗМОЖНОСТИ ИСПОЛЬЗОВАНИЯ ПРОДУКТА.

•

FUSION не берет на себя и не уполномачивает никакие центры обслуживания, лица или субъекты брать на себя от ее имени никакие другие обязательсва

или отвественность помимо тех, которые явно предусмотрены этой гарантией.

Вся гарантийная информация, характеристики и спецификации продуктов могут быть изменены без предупреждения.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

DUTCH

DE FUSION-BELOFTE VAN KWALITEIT

1 JAAR BEPERKTE CONSUMENTENGARANTIE

FUSION Electronics Limited (‘FUSION’) garandeert dat deze Fusion-speaker, -subwoofer, -versterker of oorspronkelijk Fusion-accessoire (‘het product’) vrij is van

materiaal- en fabricagefouten, overeenkomstig de volgende voorwaarden en bepalingen:

•

De beperkte garantie voor het gekochte Fusion-product beperkt zich tot de eerste twaalf (12) maanden vanaf de aankoopdatum van het product.

De beperkte garantie geldt uitsluitend voor de originele aanschaf door de consument van het product en kan niet worden toegewezen of overgedragen aan enige

daaropvolgende koper/eindgebruiker.

•

De beperkte garantie geldt uitsluitend voor consumenten die het product hebben gekocht in één van de landen (of gebieden) vermeld op www.fusionelectronics.com. De

beperkte garantie is uitsluitend geldig in een land (of gebied) dat door Fusion bedoeld is voor verkoop van het product.

Tijdens de beperkte-garantieperiode zal Fusion of haar geautoriseerde servicenetwerk elk defect product of eventuele onderdelen daarvan bij FUSION zelf of bij een door

FUSION geautoriseerde dealer repareren of door nieuw vervangen en het product in werkende staat aan de consument retourneren. De consument zal niets hoeven te

betalen voor de onderdelen of de arbeidskosten voor het repareren of vervangen van het product. Alle vervangen onderdelen en kosmetische onderdelen moeten op het

moment van verzending vrij zijn van defecten en vallen daarom niet onder de voorwaarden van deze beperkte garantie.

•

Het gerepareerde product wordt gegarandeerd voor de resterende dagen van de originele garantieperiode of gedurende negentig (90) dagen na de datum van reparatie, wat

het langste is.

Alle garantieclaims moeten vergezeld gaan van een kopie van dit garantiebewijs en een kopie van het bewijs van de aankoopdatum.

De consument heeft geen dekking of voordelen krachtens deze beperkte garantie indien een van de volgende omstandigheden zich voordoet:

•

het product heeft te lijden gehad van: abnormaal gebruik, abnormale omstandigheden, verkeerde opslag, blootstelling aan overmatig vocht of te grote vochtigheid,

blootstelling aan te hoge temperatuur of andere dergelijke omgeviongsfactoren, niet-geautoriseerd modiﬁcatie, niet-geautoriseerde aansluitingen, niet-geautoriseerde

reparatie inclusief maar niet beperkt tot gebruik van niet-geautoriseerde onderdelen bij de reparatie, verkeerd gebruik, verwaarlozing, misbruik, ongeluk, verandering,

onjuiste installatie, force majeure, gemorst(e) voedsel of vloeistof, verkeerde afstelling van de bediening of andere handelingen die waar Fusion geen controle over heeft,

zoals gebreken aan verbruiksonderdelen zoals zekeringen, en breuk of schade aan antennes tenzij deze rechtstreeks zijn veroorzaakt door materiaal- of fabricagefouten,

en de normale slijtage van het product.

•

Fusion was niet door de consument ingelicht over het beweerde defect of beweerde slechte werking van het product tijdens de geldende beperkte-garantieperiode.

Het productserienummer of de datumcode op het accessoire is verwijderd, onleesbaar gemaakt of veranderd.

Het product is gebruikt met of aangesloten op een accessoire dat niet door Fusion is meegeleverd of niet geschikt is voor gebruik met het Fusion-product, of gebruikt op

een wijze anders dan het bedoelde gebruik.

Als er tijdens de beperkte-garantieperiode een probleem ontstaat, moet de consument de volgende stapsgewijze procedure volgen:

1. De consument zal het product voor reparatie of vervanging naar de plaats van aankoop terugbrengen.

2. Eventuele onderdelen of arbeidskosten die niet door deze beperkte garantie worden gedekt zijn ook voor rekening van de consument. De consument is verantwoordelijk

voor de kosten in verband met herinstallatie van het product.

3. Als het product na aﬂoop van de garantieperiode aan Fusion wordt geretourneerd, zal het normale servicebeleid van Fusion gelden en worden de consument

dienovereenkomstig kosten berekend.

DE IN DEZE BEPERKTE GARANTIE BEPAALDE VOORZIENINGEN GELDEN VOOR ZOVER ZE NIET KUNNEN WORDEN VERVANGEN DOOR ENIGE ANDERE RECHTEN EN

RECHTSMIDDELEN ONDER ENIGE GELDENDE WETGEVING DIE NIET KAN WORDEN UITGESLOTEN. OVERIGENS WORDT VOOR ZOVER DAT BIJ DE WET IS TOEGESTAAN, ELKE

IMPLICIETE GARANTIE UITGESLOTEN. DE HIERVOOR VERMELDE GARANTIE IS DE ENIGE EN EXCLUSIEVE GARANTIE VOOR DE KOPER EN VERVANGT ALLE ANDERE

UITDRUKKELIJKE OF IMPLICIETE GARANTIES. VOOR ZOVER BIJ DE WET TOEGESTAAN, ZAL FUSION NIET AANSPRAKELIJK ZIJN VOOR INCIDENTELE OF GEVOLGSCHADE OF

EEN VERLIES VAN VERWACHTE VOORDELEN OF WINSTEN UIT HET GEBRUIKEN OF NIET KUNNEN GEBRUIKEN VAN HET PRODUCT.

•

Fusion accepteert geen enkele andere verplichting of aansprakelijkheid boven hetgeen uitdrukkelijk in deze garantie is vermeld en autoriseert geen enkel geautoriseerd

reparatiecentrum of persoon of eenheid om deze voor haar te accepteren.

•

Alle informatie over garantie, productfuncties en speciﬁcaties kunnen zonder kennisgeving worden gewijzigd.

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

________________________________________________

_______________________________________________

________________________________________________

_______________________________________________

________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

________________________________________________

_______________________________________________

________________________________________________

_______________________________________________

________________________________________________

Download from Www.Somanuals.com. All Manuals Search And Download.

WWW.FUSIONELECTRONICS.COM

FUSION Electronics New Zealand

FUSION Electronics Australia

FUSION Electronics Europe

FUSION Electronics USA

09 369 2900

1300 736 012

+31 76 5723 632

623 580 9000

FUSION Electronics Paciﬁc

+64 9 369 2900

Download from Www.Somanuals.com. All Manuals Search And Download.

Eicon Networks Network Card D 120JCT LSU User Manual
Euro Pro Garbage Disposal GC130HS User Manual
Exabyte Computer Drive 1005911 003 User Manual
Fender Stereo Amplifier Hot Rod DeVille ML User Manual
Fujioh Ventilation Hood FSR 3000 User Manual
Fujitsu Printer PRN608 S User Manual
Gaggenau Dishwasher DF 241 User Manual
Gary Fisher Kitchen Entertainment Center Axiom Cycling Computer User Manual
GE Air Conditioner MG_24 User Manual
Gianni Industries Switch TS 980 User Manual