Fusion Marine Instruments MS RA50 User Manual

MARINE HEADUNIT

MS-RA50

Specifications and design are subject to change without notice

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

CONTENTS

.......................................................................................................................................................................................................

•

USER INTERFACE AND CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 4

Control Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 4

Key Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 4

ROTARY ENCODER AND MENU KEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 5

Rotary Encoder Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 5

Menu Key Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 5

Using the Encoder and Menu Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 6

GETTING STARTED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 7

Powering the Unit On or Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 7

Input Source Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 7

Adjusting Volume Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 8

Muting Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 8

Adjusting Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 9

Adjusting Screen Brightness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 9

TUNER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 10

Listening to the Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 10

Tuner Source Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 10

Tuning Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 11

Adding and Removing Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 12

iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 13

Playing Content. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 13

iPod Source Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 13

Controlling iPod Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 14

Changing iPod Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 15

AUXILIARY INPUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 16

Listening to Auxiliary Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 16

Auxiliary Source Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 16

INSTALLING THE RA50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 17

Mounting the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 17

Mounting Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 18

Installation Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 19

Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 19

Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 20

RA50 Cable Connection Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 21

SETTING UP THE RA50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 22

Preparing for iPod Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 22

Advanced Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 22

APPENDICES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 24

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 24

RA50 Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 25

Support, Sales and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 26

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 26

Licensing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg 27

•

Download from Www.Somanuals.com. All Manuals Search And Download.

LICENSING

USER INTERFACE AND CONTROLS

CONTROL PANEL LAYOUT

Apple, the Apple logo, iPod and iTunes are trademarks of Apple Computer, Inc., registered in

the US and other countries.

KEY NAMES

Key

Name

Key

Name

MUTE

POWER

BACKWARD

ROTARY ENCODER

SOURCE

PLAY / PAUSE

FORWARD

notice. Product availability may vary between sales regions. “Made for iPod,” “Made for iPhone,” mean that an electronic accessory has been

designed to connect specifically to iPod, iPhone, respectively, and has been certified by the developer to meet Apple performance standards.

Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of

this accessory with iPod or iPhone may affect wireless performance.

YOU CAN HELP PROTECT THE ENVIRONMENT!

Please remember to respect the local regulations:

Hand in the non-working electrical equipment

to an appropriate waste disposal center.

Download from Www.Somanuals.com. All Manuals Search And Download.

General specifications

Operating voltage

Fuse rating

ROTARY ENCODER AND MENU KEY

10.2–16 VDC negative ground

7.5 amp

Although the controls of the RA50 are designed to be intuitive to use, we recommend that you

familiarize yourself with the operation of the Encoder and Menu key before using the unit.

Power output

Maximum

Pre-output voltage

40 W x 2

3.0 VRMS

ROTARY ENCODER OPERATION

You can use the Encoder in three ways to control the operation of the RA50:

TUNING RANGE

Europe and Australasia

Rotary Encoder turn

FM radio frequency range 87.5–108 MHz.

Frequency step 100 kHz

AM radio frequency range 522–1620 MHz.

Encoder press

Frequency step

9 kHz

USA

Encoder press and hold down for at least one second

FM radio frequency range 87.5–107.9 MHz.

Frequency step 200 kHz

AM radio frequency range 530–1710 MHz.

Frequency step

10 kHz

MENU KEY OPERATION

You can use the Menu key to open or to exit from menus:

Japan

FM radio frequency range 70–90 MHz.

Frequency step 50 kHz

AM radio frequency range 522–1620 MHz.

Press the Menu key to open a menu.

Menu key

Frequency step

9 kHz

In an open menu you can use the Menu key at any time to save

changes and exit:

Menu exit

•

Press the Menu key to exit from the current menu level.

Press and hold down the Menu key to exit from the menu

completely.

Time out feature: After a few seconds inactivity, the menu exits and

any changes are saved automatically.

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE ENCODER AND MENU KEY

You can use the Encoder and Menu key to adjust levels and access menus.

ADJUSTING LEVELS

Use the Encoder and Menu key to adjust levels on the RA50. For example, to adjust the volume

level:

Turn Encoder to

open the Volume

screen

Turn Encoder to

adjust the level.

Press Menu to exit

(or leave to time

out). See “Menu

Key Operation” on

page 5.

Mounting Bracket (Part # MS-HUGMS)

Surface mounts your RA50 Marine Stereo using the gimbal mounting bracket. The bracket

can be positioned above or below the RA50 providing a wide choice of mounting options. The

bracket is gimbal mounted to the RA50 allowing adjustment of the viewing angle.

ACCESSING MENUS

Use the Menu key and Encoder to access menus to change settings. For example, to access

the Settings menu while in Tuner or AUX mode.:

SUPPORT, SALES AND SERVICE

FUSION Electronics in New Zealand

FUSION Electronics Australia

FUSION Electronics Europe

FUSION Electronics USA

+ 64 9 369 2900

+ 61 1300 736 012

+31 76 572 3632

+1 623 580 9000

The Settings

menu is

displayed

Press Menu to

exit. See “Menu

Key Operation”

on page 5.

Press Menu

key

The menu is

displayed

Turn Encoder to

scroll the highlight.

Press Encoder to

select Settings

menu.

Website: www.fusionelectronics.com

SPECIFICATIONS

MULTI-LEVEL MENUS

All of the menus on the RA50 have more than one level. To access items in multi-level menus:

FCC compliance statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions:

•

Turn the Encoder to highlight a menu item, then

Press the Encoder to select the highlighted item.

Repeat these steps as many times as necessary to reach the menu item you require.

•

this device may not cause harmful interference, and

this device must accept any interference received, including interference that may cause

In this manual, accessing a multi-level menu item is shown by listing the menu items in order,

as in the following example:

undesired operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTINGS > TONE

RA50 ACCESSORIES

The above example means: “turn and then press the Encoder to select the Settings menu”

then “turn and then press the Encoder to select the Tone menu”.

GETTING STARTED

POWERING THE UNIT ON OR OFF

When you power on the RA50 it will automatically start playing music from the most recently

selected input source.

TO POWER THE UNIT ON OR OFF.

•

Momentarily press the Power key to power on the unit. As the unit starts up, a

splash screen is displayed for several seconds, followed by the input source screen

for the current input source.

Cable for iPod - 1.5m (Part # MS-IP15L3)

Connects your iPod to your RA50 Marine Stereo, enabling full control and navigation of your

iPod from the RA50.

Power

•

When the unit is on, momentarily press the Power key to power off the unit.

INPUT SOURCE SCREENS

The RA50 supports input from several types of source:

•

AM/FM radio

iPod/iPhone via external connector or docking unit

Auxiliary input.

Press the Input source key (

order:

) to step through the input source types in the following

iPod (if connected)

Aux

iPod EXTERNAL DOCK (Part # MS-IPDOCKG2)

Connect this external iPod dock to the RA50 Marine Stereo to provide the additional benefit

of an integrated housing for your iPod. The bulkhead mount dock complies with IPx5

Waterproof Standards, protecting your iPod from the harsh marine environment. The iPod

marine external dock can be flush mounted or wall mounted.

When you select one of these sources, the RA50 displays a source screen, similar to the AM

source screen shown in Figure 1 below. The title bar always shows the source name and signal

strength. Other additional information varies depending on the source type you have selected.

Note: The water ingress rating is on the front of the dock when correctly bulkhead mounted.

Download from Www.Somanuals.com. All Manuals Search And Download.

My Head unit keeps turning itself off then back on when connected to my iPod

This could be happening due to corrupt files and/or a corrupted version of the operating soft-

ware on your iPod. If you connect to your computer you may get a message on the iPod similar

to this: “The iPod ‘John’s iPod’ could not be updated because the firmware was corrupt.

Click this link to get a step-by-step guide to solve this issue: http://support.apple.com/kb/

ts1813.”

SOURCE NAME

SIGNAL

STRENGTH

SELECTED

FREQUENCY

Why does my FUSION Head unit keep locking up when connected to my iPod/iPhone?

If you are experiencing software lock-ups or your unit freezes:

TUNING

MODE

•

Reset the Head unit by holding down the power button for 10 seconds or pressing the

reset button inside the face plate.

Figure 1 – Example source screen (AM input selected)

•

Reset your Apple iPhone by powering down and then restarting the phone.

Reset your iPod (see Apple website from model-specific information). This should resume

normal operation.

•

Make sure you have the latest version of iTunes and the latest operating software in your

iPod/iPhone. It is important to update software when Apple releases new versions. If you

are connected via a dock, ensure you are using the correct sleeve and the connection to

the Head unit is secure.

ADJUSTING VOLUME LEVEL

To adjust the volume level:

Will my iPod/iPhone connect to my FUSION product if the battery is flat?

No. It will take a number of minutes for the Apple product to get a minimum level of charge

before it can connect and become operational. Please connect and wait for the unit to initialise.

Turn Encoder

The Volume

screen is

displayed

Turn Encoder to

adjust.

Press Menu to exit.

See “Menu Key

Operation” on page 5.

My iPod/iPhone will not connect to the Head unit while in the dock.

If your Head unit displays “No iPod connected” while using iPod as input source:

•

Check that you are using the correct sleeve combination. If you have the incorrect sleeve

combination this could prevent the iPod connector from mating correctly. It could also

damage the connector in the dock or your iPod/iPhone itself.

If you are uncertain which iPod model you have, go to http://www.apple.com/support/ to get

the correct model information for your iPod and sleeve.

If you are still unable to connect once you know for certain you have the correct iPod/iPhone–

sleeve combination:

MUTING OUTPUT

•

Ensure that you have the latest version of operating software installed in your iPod/iPhone

and the latest iTunes version. To do this, connect your iPod/iPhone to iTunes and it will

check and, if necessary, prompt you to download the latest version.

To mute and unmute the volume:

•

Press the Mute key to mute the audio output. The Mute icon is displayed over the

top of the current input source screen.

If you are still unable to connect once you have confirmed that you have the latest software or

you have updated your iPod/iPhone:

Press the Mute key again to unmute the audio output. The volume continues at the

•

Reset the iPod/iPhone (see the user manual for your Apple product) and also reset the

Head unit (see FUSION user manual).

Mute

previously set level.

If you are still unable to connect:

•

Contact your FUSION dealer or contact FUSION via the tech email.

Download from Www.Somanuals.com. All Manuals Search And Download.

Volume limit

ADJUSTING TONE

Use this option to set the maximum output volume level that can be selected by users.

To change the bass or treble level:

To maximum volume limit:

1. Press the Menu key.

2. Turn and then press the Encoder to select Settings > Volume limit.

3. Turn the Encoder to set the require volume level.

4. Press the Menu key (or leave to time out) to save the setting and exit.

Press Menu

key

Select:

Settings > Tone

The Tone menu is

displayed

Turn Encoder to

adjust. Press

Encoder to

select.

Press Menu to

exit. See “Menu

Key Operation”

on page 5.

Note: The volume limit setting controls the maximum volume output level but does not limit

the volume shown on the Volume screen.

APPENDICES

ADJUSTING SCREEN BRIGHTNESS

Use the LCD menu to adjust the contrast or brightness of the screen display.

You can press the Menu key at any time (or leave to time out) to save the current brightness

level and exit.

TROUBLESHOOTING

Resetting the unit

Should the RA50 unit become unresponsive:

To adjust the contrast or brightness of the display screen:

•

Press and hold the ‘Power’ button for 10 seconds to reset the unit.

Reset your iPod/iPhone.

•

Remove all power for 5 minutes and then reconnect.

Tuning

If you are unable to tune to radio stations, check you have the correct tuner region selected

For further information, see “Tuner region” on page 23 .

Press Menu

key

Select:

Settings > LCD

The LCD menu is

displayed

Turn Encoder to

adjust. Press

Encoder to

select.

Press Menu to

exit. See “Menu

Key Operation”

on page 5.

iPod TROUBLESHOOTING

Problem Solution

Screen brightness can be linked to the vessels lighting system, see “Installing the RA50”

on page 19

iPod

Why do I get an error message when I dock my iPhone to my MS-RA50

Some iPhone models may intermittently display the message: “This accessory is not made to

work with the iPhone. Would you like to turn on airplane mode to reduce audio interference?

You will not be able to make or receive calls.” when initially docked with any FUSION iPhone

compatible product. All FUSION iPhone-supported products have been tested and certified by

Apple, and passed Apple’s stringent “Works with iPhone” self-certification test.

Despite this message, all fusion iPhone-compatible products are fully functional and compatible

with Apple’s iPhone product line.

Please choose “NO”, or simply wait for this message to time out.

Download from Www.Somanuals.com. All Manuals Search And Download.

To select the required display language:

TUNER

1. Press the Menu key.

2. Turn and then press the Encoder to select Settings > Language.

3. Turn the Encoder to highlight the required language.

4. Press the Encoder to select the highlighted language.

5. Press the Menu key (or leave to time out) to save the setting and exit.

LISTENING TO THE TUNER

To select one of the available tuner bands:

Press the Input source key (

) to select input from each of the following in turn:

•

Power save

The applicable input source screen is displayed for each band.

If you are operating the RA50 on battery power, you can turn on the power save option to

reduce drain on the battery. The LCD screen shuts down automatically after 1 minute of

inactivity (press any key to restore display).

Continuing to press the key will display the input source screens for iPod (if connected) and

Auxiliary as described in the section “Input Source Screens” on page 6.

To enable or disable power saving mode:

1. Press the Menu key.

2. Turn and then press the Encoder to highlight Settings > Power save.

3. Press the Encoder to turn on power saving ( ) or turn off power saving

TUNER SOURCE SCREENS

AM/FM

(

4. Press the Menu key (or leave to time out) to save the setting and exit.

An example of a typical tuner input source screen is shown in Figure 2 below.

Tuner region

Use this option to select the correct region to ensure the RA50 tunes correctly to your local

radio stations.

SOURCE NAME

SIGNAL

STRENGTH

To change the tuner region setting:

1. Press the Menu key.

SELECTED

FREQUENCY

2. Turn and then press the Encoder to select Settings > Tuner region.

3. Turn the Encoder to highlight the required region:

TUNING

MODE

•

Europe

USA (default region)

Japan

Figure 2 – Example source screen (AM input selected)

•

Australasia.

4. Press the Encoder to select the region ( ).

5. Press the Menu key (or leave to time out) to save the setting and exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

TUNING METHODS

SETTING UP THE RA50

You can use three methods to tune the RA50: automatic, manual and preset.

PREPARING FOR IPOD INPUT

This section describes how to prepare for iPod input.

When using your iPod:

• Always remove your iPod from the unit when not in use and do not leave in your vessel. This

helps reduce risk of theft or damage as vessel cabins can reach extreme temperatures.

Encoder

Menu key

Play / Pause

Forward

Backward

• Do not remove iPod or use stereo in a distracting manner while operating the vessel. Check

and obey all marine laws in association with use.

To tune to a required frequency, channel or preset:

Press the Play / Pause key to step through the available tuning methods for each band:

Connecting your iPod

Before you can use your iPod for input, you must first connect the device to the RA50.

You can connect your iPod to the RA50 unit:

Tuning Method

Auto

When tuning with this method…

•

Press the Forward or Backward key to start searching for available

• By using an accessory cable.

stations.

• By using a docking unit. For added protection, you can connect your iPod to the RA50 by

using a Fusion iPod Dock MS-IPDOCKG2.

Note: The search stops when a station is found or when the unit has

scanned all available frequencies once.

For further information, see “RA50 Accessories” on page 25.

Manual

Preset

•

Press the Forward or Backward key to step through the range of

frequencies one at a time.

Note: You cannot select iPod input without first connecting the device.

•

Press the Forward or Backward key to step through available presets

(only available if there are two or more presets)

To connect your iPod to the RA50 by accessory cable:

1. Plug the MS-IP15L3 accessory cable into the base of your iPod.

2. Plug the accessory cable into the RA50 cable located at the rear of the unit.

3. Select input from the device, as required.

To tune to a specific preset:

Press the Menu key.

Press the Encoder to select Presets.

Turn the Encoder to highlight the required preset.

Press the Encoder to tune to the highlighted preset.

Menu exit. See “Menu Key Operation” on page 4.

For further details, see “

Adding and Removing Presets” on page 11.

ADVANCED SETTINGS

The settings described in this section are usually set up when the unit is installed and not

changed again.

Language

The RA50 can display menus and screens in English, Dutch, French, German, Italian or

Spanish.

Download from Www.Somanuals.com. All Manuals Search And Download.

ADDING AND REMOVING PRESETS

RA50 CABLE CONNECTION DIAGRAM

The RA50 allows you to set up your favorite AM/FM stations as presets for easy recall.

Note:

Up to 15 presets can be stored for each radio band.

When you are using the tuner, the Play / Pause, Forward, Backward, and Menu keys provide

special options to allow you to work with preset frequencies (AM/FM).

Encoder

Menu key

Play / Pause

Forward

Backward

To add a new preset:

Do one of the following.

1. Tune the RA50 to the required frequency.

2. Press and hold down the Play / Pause key. The message: “Preset saved” is displayed

briefly.

1. Press the Menu key.

2. Turn and then press the Encoder to select Presets > Save current. The message: “Preset

saved” is displayed briefly.

Note: New presets must be unique. If you try to create a preset for the same frequency as an

existing one, the unit displays the message “Previously saved”.

To remove one or more presets:

1. Press the Menu key.

2. Turn and then press the Encoder to select Presets > Remove preset.

3. Do one of the following (there is no warning or confirmation prompt before deletion):

•

Select Remove all presets and press the Encoder to remove all current presets.

The message: “Presets removed” is displayed briefly.

Figure 8 – RA50 cable connection diagram

•

Select a preset and press the Encoder to remove the selected preset. The selected

preset is removed from the list.

4. Press the Menu key (or leave to time out) to exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

CABLES

iPod

Description (colour)

Power +12VDC (Yellow)

Negative ground (Black)

Remote amplifier turn on (Blue)

Dim +12V switched (Orange)

PLAYING CONTENT

Before you can use your iPod as an input source you must first connect the device to the

RA50. For further details, see “Preparing for iPod Input” on page 22.

To listen to input from your iPod:

Dim

Connect to vessel lighting system to dim LCD and button illumination when vessel lights are

turned on.

Press the Input source key (

) until the iPod input source screen is displayed.

Continuing to press the key will display the input source screens for Auxiliary, AM and FM as

described in the section “Input Source Screens” on page 7.

Aux input

Connect an Auxiliary source to the left and right RCA (White = L, Red = R).

Lineout

iPod SOURCE SCREEN

Connect to an external amplifier (White = L, Red = R).

An example of a typical iPod input source screen is shown in Figure 3 below.

PLAYBACK MODE INDICATOR:

Repeat

Shuffle

(if active)

PLAYBACK

STATUS

INDICATOR:

Play

CURRENT

TRACK DETAILS

Pause

Fast forward

Rewind

ELAPSED TIME

PROGRESS BAR

TRACK

DURATION

Figure 3 – Example iPod input source screen

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROLLING IPOD PLAYBACK

INSTALLATION WARNING

Selecting tracks from a playlist

Caution! The MS-RA50 is designed for vessels with a 12V DC Negative ground electrical

system.

There can be thousands of tracks stored on an iPod, so you need to select the tracks you wish

to play from one of the groupings available (such as Playlists, Artists, Albums). For example, to

select tracks by artist:

•

Ensure the marine vessel’s +12V lead is removed from the battery before any equipment

is connected.

Investigate the marine vessel’s fuel tanks and electrical wiring locations before you begin

installation.

Ensure all wiring is protected to avoid damage.

Press Menu

key

Turn Encoder to

scroll the highlight.

Press Encoder to

select Artist.

Turn Encoder to scroll the highlight.

Press Encoder to select an item.

You must navigate to select All or a

specific track or Album for the unit to

start playing.

Press Menu to

exit. See “Menu

Key Operation”

on page 5.

When wiring the MS-RA50, ensure that the wires are away from sharp objects and that

rubber grommets and insulated bungs are used when routing the wiring. Ensure that when

connecting the wires to the speakers and audio system, the terminals and connections are

protected from shorting to each other.

Controlling Playback

Note: Ensure the Aerial cable is routed away from any power cables, and is the minimal

length, as long cable runs will affect AM reception performance.

You can control iPod playback with the Play / Pause, Forward and Backward keys. The

selected track starts playing automatically.

For optimum radio reception, please ensure you use an independent AM/FM marine antenna

(ground independent). Please refer to the following site for further info: www.pacificaerials.co.nz

If you want to:

Use:

Notes:

Play / Pause a

track

•

Press the key to pause the current track. The

pause icon ( ) is displayed top right in the

input source screen.

CONNECTIONS

•

Press the key again to resume play. The play

Connections and cables on the RA50 are described below. For further details of cabling, see

Figure 8 on page 21.

(

) icon is displayed in the input source screen.

Play / Pause

Forward

Skip to next track

Press the key to skip to the start of the next track.

Aerial connection

Connect an AM/FM marine antenna to the antenna socket.

iPod connection

•

Press the key to skip to the start of the current

track.

MS-IPDOCKG2 Marine Docks for iPod (not included) or a MS-IP15L3

accessory cable (not included).

Press the key twice to skip to the start of the

previous track.

Backward

Fast forward /

backward

•

Press and hold down the key to fast forward (or

backward) the playback. The fast forward (

)

(or backward) icon is displayed in the input source

screen.

Forward, or

Backward

Download from Www.Somanuals.com. All Manuals Search And Download.

CHANGING IPOD SETTINGS

55.0 (2-3/16”)

Additional iPod control features are available through the iPod Settings menu.

To change a setting in the iPod Settings menu:

Press Menu

key

The iPod control

menu is displayed

Turn Encoder to

scroll the high-

light down to

Press Encoder to

select iPod

Settings. Change

settings as

Press Menu to

exit. See “Menu

Key Operation”

on page 5.

iPod Settings.

described below.

Turn and then press the Encoder to select Repeat or Shuffle.

Turn the Encoder to highlight the required value and press the Encoder to select ( ) it.

Repeat

Figure 6 – RA50 unit side view (Scale 1:1)

•

Off. Repeat mode is turned off

One. Repeat the current song

All. Repeat all songs in the current playlist

Caution! These images are not to scale. Dimensions are shown in millimeters (mm) and inches (”).

Shuffle

•

Off. Random play shuffle is turned off

Tracks. Shuffle tracks on the current album

Albums. Shuffle albums in the current Selection.

MOUNTING CUT OUT DIAGRAM

Figure 7 – Cutting size diagram for installing the RA50 unit (not to scale)

A 1:1 scale mounting diagram is provided in the box and available online for download.

Download from Www.Somanuals.com. All Manuals Search And Download.

AUXILIARY INPUT

INSTALLING THE RA50

LISTENING TO AUXILIARY INPUT

MOUNTING THE UNIT

The RA50 can accept audio from devices with an audio output such as an MP3 player, TV,

games console, computer or DVD player.

Important! If any modification to the vessel is required, such as drilling holes, FUSION

recommends that you consult with your boat dealer or manufacturer beforehand.

Note:

An adaptor cable may be required.

1. Create mounting hole for product and drill screw pilot holes. Refer to mounting template

The Left and Right AUX input RCA cable is located at the rear of the unit.

included with product or download from www.fusionelectronics.com

2. Fit mounting gasket.

To listen to input from an auxiliary device:

3. Insert the unit into the mounting hole.

4. Use the supplied 4 x self tapping screws, to fix the unit into position.

5. Attach screw covers.

Press the Input source key (

) until the AUX input source screen is displayed.

Continuing to press the key will display the input source screens for AM, FM and iPod

(if connected) as described in the section “Input Source Screens” on page 13.

Note: Appropriate mounting is very important to ensure correct operation. Select a

location that allows both free/open airflow around rear of chassis, whilst minimizing

exposure to moisture. Allow adequate room at the rear of the unit for the cable looms

(approx. 50 mm or 2”).

AUXILIARY SOURCE SCREEN

The input source screen displayed when you select auxiliary input is shown in Figure 4 below.

Figure 4 – Example of auxiliary input source screen

Figure 5 – Locating the RA50 unit into the mounting panel

Download from Www.Somanuals.com. All Manuals Search And Download.

Electro Voice Stereo Amplifier PA4150 User Manual
Eureka Blower eureka User Manual
EverFocus Security Camera ED700 User Manual
Extron electronic Stereo System MHR 5STP 2 User Manual
Faber Ventilation Hood 630003638 User Manual
Fisher Price Baby Accessories M3177 User Manual
Furman Sound Music Mixer SRM 80A User Manual
Furuno TV Converter Box AD 10S User Manual
Geemarc Telephone AMPLI600 User Manual
GE Ventilation Hood ZV755SPSS User Manual