Furuno SONAR CSH 23 User Manual

Back

COLOR SCANNING SONAR

CSH-23/23F/24/24F

MODEL

Download from Www.Somanuals.com. All Manuals Search And Download.

The paper used in this manual

is elemental chlorine free.

FURUNO Authorized Distributor/Dealer

9-52 Ashihara-cho,

Nishinomiya 662-8580, JAPAN

Telephone : 0798-65-2111

Fax

0798-65-4200

FIRST EDITION :NOV. 1997

Printed in Japan

: OCT. 05, 2006

Pub. No. IME-13040-J3

*00080806903*

* 0 0 0 8 0 8 0 6 9 0 3 *

( TATA )

CSH-23/24/F

*IME13040J30*

* I M E 1 3 0 4 0 J 3 0 *

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY INSTRUCTIONS

WARNING

Do not open the cover

unless totally familiar with

electrical circuits and

service manual.

Install the specified transducer tank

in accordance with the installation

instructions. If a different tank is to be

installed the shipyard is solely respon-

sible for its installation, and it should

be installed so the hull will not be

damaged if the tank strikes an object.

High voltage exists inside the

equipment, and a residual

charge remains in capacitors

several minutes after the

power is turned off. Improper

handling can result in electri-

cal shock.

The tank or hull may be damaged if the

tank strikes an object.

If a steel tank is installed on a wooden

or FRP vessel, take appropriate

measures to prevent electrolytic

corrosion.

Turn off the power at the switchboard

before beginning the installation.

Fire or electrical shock can result if the

power is left on.

Electrolytic corrosion can damage the

hull.

Do not install the equipment where it

may get wet from rain or water splash.

Be sure that the power supply is

compatible with the voltage rating of

the equipment.

Water in the equipment can result in fire,

electrical shock or equipment damage.

Connection of an incorrect power supply

can cause fire or equipment damage. The

voltage rating of the equipment appears

on the label above the power connector.

Be sure no water leaks in at the trans-

ducer installation site.

Water leakage can sink the vessel. Also

confirm that the transducer will not loosen

by ship’s vibration. The installer of the

equipment is solely responsible for the

proper installation of the equipment.

FURUNO will assume no responsibility for

any damage associated with improper

installation.

CAUTION

Ground the equipment to

prevent electrical shock and

mutual interference.

Observe the following compass safe

distances:

Standard Steering

Display unit

for CSH-23

0.9 m

0.68 m

Display unit

for CSH-24

1.70 m

1.30 m

1.05 m

Processor

unit

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

1. SYSTEM CONFIGURATION ............................................................................ 1

2. EQUIPMENT LISTS .......................................................................................... 2

3. MOUNTING THE EQUIPMENT

3.1 Mounting the Hull Unit and Receiver Unit ........................................................................3

3.2 Mounting the Display Unit/Sub-display Unit .....................................................................9

3.3 Mounting the Transmitter Unit........................................................................................10

3.4 Mounting the Interface Unit............................................................................................10

3.5 Mounting the FNZ Joint Box ..........................................................................................10

3.6 Grounding the Equipment ............................................................................................11

4. WIRING

4.1 Cable Configuration.......................................................................................................12

4.2 How to Use the Crimping Tool, Pin Extractor.................................................................13

4.3 Location of Connectors ................................................................................................14

4.4 Fabricating Cables, Assembling Connectors .................................................................15

4.5 Connection of Transducer Cables..................................................................................23

4.6 Connection of Interface Unit CS-120A .........................................................................24

4.7 Connection of Sub-display Unit CSH-236/236F (Option) ...............................................29

4.8 Synchronizing Transmission with Other Sonars, Echo Sounders...................................30

4.9 Interlocking Operation with Other Sonar........................................................................32

5. CHANGING POWER SPECIFICATIONS ...................................................... 34

6. ADJUSTMENT AND CHECK

6.1 Hull Unit Check..............................................................................................................35

6.2 Heading Adjustment ......................................................................................................36

6.3 DIP Switch Setting in the Display Unit ...........................................................................37

6.4 Setting and Adjustment of the Interface Unit CS-120A...................................................38

7. PROCESSOR UNIT CSH-235/235F ............................................................... 42

SPARE PARTS/INSTALLATION MATERIALS/ACCESSORIES .................... A-1

OUTLINE DRAWINGS...................................................................................... D-1

INTERCONNECTON DIAGRAMS.....................................................................S-1

Download from Www.Somanuals.com. All Manuals Search And Download.

1. SYSTEM CONFIGURATION

STANDARD

OPTION

DISPLAY UNIT

CSH-230 (CSH-23)

CSH-230F (CSH-23F)

CSH-2400 (CSH-24)

CSH-2400F (CSH-24F)

MONITOR (MU-151C)*

COMMERCIAL MONITOR*

PROCESSOR UNIT*

CSH-235

SUB DISPLAY*

CSH-236

REMOTE CONTROL BOX

CSH-116

CSH-235F

*: CSH-23/23F only

100 VAC

INTERFACE UNIT

CS-120A

STEP-DOWN

TRANSFORMER

PT-400

110/115/220/230 VAC

TRANSMITTER UNIT

CSH-310 (CSH-23/24)

CSH-310FII (CSH-23F/24F)

SPEED LOG

AD CONVERTER

NAVIGATOR

CURRENT INDICATOR

COLOR VIDEO SOUNDER

VI-1100A

INTERFACE UNIT

RECEIVER UNIT

CSH-220A (CSH-23/24)

POWER SUPPLY UNIT

CSH-380B (CSH-23/24)

CSH- 220FII (CSH-23F/24F)

CSH-380S (CSH-23F/24F)

ECHO SOUNDER, COLOR

VIDEO SOUNDER

NET SONDE

FNZ JOINT BOX

CS-170

100/110/220 VAC

HULL UNIT

CSH-21080 (800 mm stroke)**

CSH-21120 (1200 mm stroke)

CSH-21160 (1600 mm stroke)

**: CSH-23/24 only.

Figure 1-1 System configuration

Download from Www.Somanuals.com. All Manuals Search And Download.

2. EQUIPMENT LISTS

Standard Supply

Name

Display Unit

Type

CSH-230

Qty

Remarks

CSH-23

CSH-23F

CSH-24

CSH-24F

CSH-230F

CSH-2400

CSH-2400F

CSH-235

CSH-235F

CSH-310

CSH-310FII

CSH-220A

CSH-220FII

CSH-21080

CSH-21120

CSH-21160

CSH-380B

CSH-380S

Processor Unit

Transmitter Unit

Receiver Unit

Hull Unit

CSH-23 Blackbox type

CSH-23F Blackbox type

CSH-23/24

CSH-23F/24F

CSH-23/24

CSH-23F/24F

stroke 800mm *

stroke 1200mm

stroke 1600mm

CSH-23/24

Power Supply Unit

CSH-23F/24F

Remote Control Box CSH-116

Interface Unit CS-120A

Installation Materials CP10-02700

1 set

CP10-02710

6 pair cable

CP10-06410

6 pair cable

CP10-03410

6 pair cable

FP10-01801

FP10-01201

FP10-01203

Nylon cover

RAM card

CSH-23/23F

CP10-06400

CSH-23/23F

Blackbox type

CSH-24/24F

CP10-03400

Accessories

FP10-02400

1 set

CSH-23/23F

FP10-03000

FP10-01900

FP10-01203

RAM card

CSH-23/23F

Blackbox type

CSH-24/24F

FP10-01901

FP10-01201

FP10-01203

Nylon cover

Hood

RAM card

Spare Parts

SP10-01700

SP10-03300

SP10-01800

SP10-03400

1 set

CSH-23/24

CSH-23 Blackbox type

CSH-23F/24F

CSH-23F Blackbox type

*:CSH-23/24 only

Download from Www.Somanuals.com. All Manuals Search And Download.

Optional Equipment

Mass

(kg)

Name

Type

CS-170

Code No.

Remarks

FNZ Joint Box

Set-down

Transformer

E/S Interface

Unit

PT-400

VI-1100A

Sub-Display

Unit

CSH-236

CSH-23/23F only

CSH-236F

FP10-01801

FP10-01901

OP10-11

FP10-02000

CSH-1600

CSH-1300

Hood

Filter

Extension

Cable Set (with

inst. materials)

37C Cable

7C Cable

16P Cable

Handle

006-027-830 For CSH-23/23F

000-690-855 For CSH-24/24F

006-997-710 For CSH-23/23F

000-690-856 For CSH-24/24F

000-068-165 For CSH-23/23F

000-069-996 For CSH-24/24F

10S1258

10S1259

10S1260

OP10-3

000-101-006 Specify length

000-101-007

000-101-008

006-949-950

Assembly

Mounting

Fixture

Automatic

Raise

OP10-9

006-990-040

000-068-927

CSH-1500

Modification Kit

ROM Option Kit OP10-15

ROM Option Kit OP10-18

006-998-620

006-998-650

Hull Unit

CSH-21081-1

Stroke 800mm, 24 Anti-slamming

kHz

type

CSH-21081-2

CSH-21121-1

CSH-21121-2

CSH-21161-1

CSH-21161-2

OP10-21

Stroke 800mm, 28

kHz

Stroke 1200mm,

24 kHz

Stroke 1200mm,

28 kHz

Stroke 1600mm,

24 kHz

Stroke 1600mm,

28 kHz

Ant slamming

Kit

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 3-2 Maintenance space, example sonar compartment

Download from Www.Somanuals.com. All Manuals Search And Download.

Shortening the retraction tank

The retraction tank is 1300 mm in length when supplied. Shorten the tank as necessary so that

the transducer is placed well below the keel when it is lowered. The following table provides

guidelines for shortening the tank. Refer also to the retraction tank installation drawing at the

back of this manual.

Installation

Method

XDCR Travel

800 mm

Remove 297

thru 382 mm

from the

Same as left

Remove 297

thru 382 mm

from the bottom.

Note that the length

"D" must be less

than 1003 mm.

Same as left

bottom.

1200 mm

1600 mm

Remove 97

thru 382 mm

from the

Same as left

Remove 97

thru 382 mm

from the bottom.

Note that the length

"D" must be less

than 1203 mm.

bottom.

Remove within

282 mm from

the bottom.

Note that the length

"D" must be less

than 1703 mm.

Remove within

282 mm from

the bottom.

Same as left

Figure 3-3 Guidelines for shortening the retraction tank

Note 1: In the 800 mm type hull unit, more than 297 mm must be removed from the bottom so

that the transducer fully protrudes from the tank. If more than 382 mm is removed, the trans-

ducer cannot be retracted into the tank.

Note 2: In the 1200 mm type hull unit, the transducer will not fully protrude unless 97 mm is

removed from the bottom, and cannot be fully retracted if more than 382 mm is removed.

Note 3: In the 1600 mm type hull unit, the transducer cannot be fully retracted if more than 282

mm is removed.

Note 4: When 382 mm (282 mm for 1600 mm type) is removed and “D” is minimum, the effect

of air foam is minimized because the transducer fully protrudes in water.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remarks for installation of retraction tank

1. Make, if possible, the installation location a double bottom structure.

2. Install, if possible, the tank on the keel where the tank can be most firmly fixed.

3. Install the reinforcement ribs as near as possible to the top of the retraction tank, allowing

space for tightening of bolts and nuts.

Figure 3-4 How to install reinforcement ribs

4. When an attachment flange is used, install reinforcement ribs to the attachment flange.

Figure 3-5 Installing reinforcement ribs to the attachment flange

5. Add a doubling plate at the location where the retraction tank is welded to the hull bottom.

The size of the doubling plate is normally 1200 mm to 1300 mm in diameter so that it lies

across two bottom frames.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing hull unit on retraction tank

After welding the retraction tank and allowing sufficient time for cooling, install the hull unit as

follows:

1. Clean the hull unit flange, the O-ring and O-ring groove and coat them with a slight amount

of grease. Place the O-ring in position on the tank flange.

2. Lay the gasket (1) on the top of the tank flange.

3. Orient the hull unit so that the bow mark (arrow) on its flange points toward the ship’s bow.

Note that heading adjustment in the display unit is required if the bow mark does not face

the ship’s bow.

4. For the 1200 mm transducer travel type, 11 of the 24 bolt holes on the hull unit flange have

already been fitted with bolts. Insert the gasket (2) into the bolt holes of the tank flange to

which these 11 bolts are fitted. Note that it is difficult to fit them after the hull unit has been

placed on the tank.

5. Confirm that the O-ring and the gasket (1) are in position. Place the hull unit on the tank.

6. Coat every bolt, washer and nut with slight amount of grease to ease removal. Fit the insu-

lation gasket (2) into the bolt holes of both the tank and hull unit flanges. Fasten the hull unit

to the retraction tank with gasket (2), flat washers, spring washers and hex bolts. (Insulation

gasket (2) and gasket (2) are used on the 1200 mm transducer travel type only.)

7. Reinforce the hull unit against vibration by extending stays to the ship’s hull from the two

eye bolts at the top of the hull unit, referring to figure at the top of the next page.

Hex. Nut

Hex.Nut

Spring Washer

Flat Washer

Spring Washer

Insulation Packing (1)

Flat Washer

Insulation Packing (1)

Insulation Packing (2)

Bow Mark

Hull Unit Flange

Insulation Packing (2)

Insulation Packing (1)

Insulation Packing (2)

Insulation Packing (1)

O-ring

Flat Washer

Hex. Bolt

Tank Flange

Insulation Packing (2)

Flat Washer

Hex. Bolt

Figure 3-6 Installation of hull unit

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing stays (anti-vibration

measure)

Install stays from the top of the hull unit to

the ship’s hull. The stays should be angle

iron with a size of 75 x 75 x 9 mm or more

and at least two pieces should be used; one

each to ship’s bow and stern directions. In-

stall if possible, two more stays in ship’s

transverse direction.

Figure 3-7 Proper installation of stays

Do not install the stays as shown below. Vibration-resistance effect is reduced since vibration is

applied to the stays as rotation force. Install them horizontally.

Proper installation

90°

Figure 3-8 Proper and wrong installation of stay

Fastening receiver unit to hull unit

Fasten the receiver unit to the left side of the hull unit

as shown at right.

A transducer cable protection cover has been fitted

where the receiver unit is to be fastened to the hull unit.

Remove it when mounting the receiver unit.

Raise/Lower

Control Box

(Attached at

Receiver

factory)

Unit

Figure 3-9 Mounting of receiver unit

Download from Www.Somanuals.com. All Manuals Search And Download.

3.2 Mounting the Display Unit/Sub-display Unit

The display unit/sub-display unit is designed for tabletop mounting. When selecting as mount-

ing location consider the following conditions:

• Place where operating personnel are able to control the unit easily while observing the fish-

ing ground or the area surrounding the vessel.

• Place at least 1 m away from a magnetic compass and components which have a magnet

(radar magnetron, loudspeaker, high power transformer, etc.)

• Place not exposed to direct sunlight, water splashes or hot

air.

• Place where maintenance and ventilation clearance shown

in the outline drawings is ensured.

• Place where the CRT face is within ±45° from vertical.

Mounting the display unit/sub-display unit

1. Remove the mounting base by unscrewing the two bolts at

the front bottom.

2. Fix the mounting base to the table with four M10 bolts, flat

washers, spring washers and nuts. It is recommended that a

rubber mat be placed under the mounting base to absorb

vibration.

3. Fasten the unit to the mounting base with two bolts. When

the space around the unit is limited, make wirings to the

display unit first and then fasten the unit.

Note: For the CSH-24, remove eye bolts at the top of the dis-

play unit and set cosmetic screws (supplied with installation

materials) to eye bolt holes.

Figure 3-10 Mounting the display unit,

sub-display unit

Download from Www.Somanuals.com. All Manuals Search And Download.

3.3 Mounting the Transmitter Unit

The transmitter unit can be mounted with or without mounting legs. For use without mounting

legs remove them and use inside mounting holes.

The transmitter unit should be reinforced against vibration by stays extending from the eyebolts

on the top of the unit.

Attach stay to

this eye bolt.

Mounting leg for

outside leg mounting

For mounting without legs,

remove legs and use inside

holes for mounting.

Figure 3-11 Transmitter unit

3.4 Mounting the Interface Unit

Since the interface unit connects with several navigation and fishing equipment, determine the

installation site with the wirings to them taken into account. Furthermore, the unit incorporates

a data selector and self-check switch, so select a place where they can be easily operated.

3.5 Mounting the FNZ Joint Box

The FNZ joint box is used for interchanging both TX trigger and sonde marker pulses from the

echo sounder and the net sonde, therefore it should be installed as close as possible to the net-

sonde indicator.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.6 Grounding the Equipment

Ground all equipment with a suitable copper strap or ground wire. The location of the ground

terminal of each unit is shown below.

CAUTION

Ground the equipment to

prevent electrical shock and

mutual interference.

TRANSMITTER UNIT

RECEIVER UNIT

DISPLAY UNIT

POWER UNIT

INTERFACE UNIT

FNZ JOINT BOX

Figure 3-12 Location of ground terminals on equipment

Download from Www.Somanuals.com. All Manuals Search And Download.

4. WIRING

4.1 Cable Configuration

Figure 4-1 Cable configuration

Download from Www.Somanuals.com. All Manuals Search And Download.

4.2 How to Use the Crimping Tool, Pin Extractor

A special crimping tool is necessary for connection of wires to the contact pins of the 38P

connector. The pin extractor removes the contact pin from the connector body. This paragraph

describes how to crimp and extract the contact pin.

Crimping Tool

06-1001-016

Contact Pin

60-8017-0313-00-039

Pin Extractor

06-1877-04

Figure 4-2a Crimping tool, contact pin, pin extractor

How to use the crimping tool

Figure 4-2b

How to use the pin extractor

If a contact pin is inserted into an incorrect hole on the con-

nector body, remove it with the pin extractor.

1. Push the pin extractor into the pin hole from the side

opposite to the pin inserting side.

2. Push in the head of the pin extractor. The retaining spring

comes free and the contact pin can be removed.

Figure 4-2c

Download from Www.Somanuals.com. All Manuals Search And Download.

4.3 Location of Connectors

Download from Www.Somanuals.com. All Manuals Search And Download.

4.4 Fabricating Cable, Assembling Connectors

Fabricating cable 00-8016-038-313-761HV

(CN-A1, CN-A5 and J201)

Anticorrosive

sheath

Shield

L = 250 (CN-A1) for Display Unit

320 (CN-A5) for Display Unit

170 (J201) for Interface Unit

Vinyl sheath

L = 470 (CN-A1) for Processor Unit

440 (CN-A5) for Processor Unit

Armor

Core

Insulating tape

Expose cores, and then wind

shield around the armor.

Figure 4-4 Fabrication cable 00-8016-038-313-761HV

Assembling the 38P connector

Shorten the unused wires appropriately and their ends with vinyl tape to prevent short circuit.

Guide Pin A

Guide Pin B

Position No.

Insulate unused wires

with vinyl tape.

Guide Pin A

(Large)

Guide Pin B

(Small)

Figure 4-5 How to assemble the 38P connector

Positioning guide pins

Guide pins of the connector identify the mating receptacle. Position them as shown below.

Table 4-1 Guide pins and connectors CN-A1, CN-A5, J201

Connector CN-A1 CN-A5 J201 Positioning Tool

Guide Pin

Guide Pin A (Large)

Guide Pin B (Small)

Type: 10-910-0179-0

Download from Www.Somanuals.com. All Manuals Search And Download.

Clamping the cable

Clamp the cable where the shield is folded back onto the armor.

Figure 4-6 Clamping the cable

Assembling connector NSC-253P (CN-A15)

Cable DPYCY-1.5

1.5

1.56

Figure 4-7 Assembling connector NSC-253P

Assembling BNC connector

(CN-A7, CN-A8, CN-A9, CN-A10, CN-A11 and

CN-A12)

1. Remove vinyl sheath of the cable by 15 mm.

2. Pass the cable through the nut, washer, gasket and clamp.

3. Unravel the shield and fold it back onto the clamp.

4. Remove the insulator, leaving 3 mm.

5. Trim the shield as shown in the drawing. Solder the center chip to

the conductor of the cable.

6. Pass the cable through the housing and tighten the nut.

Figure 4-8 Assembling BNC connector

Download from Www.Somanuals.com. All Manuals Search And Download.

Fabricating cable 54-038-000-601/SC (CN-E1)

Figure 4-9 Fabricating cable 54-038-000-601/SC

Assembling 38P connector

1. Bundle the unused wires outside the connector case.

2. Fix the cover 1, taking heed of the cable outgoing direction.

3. Dress the wires and fix the cover 2 and 3. Use a fragment of cable sheath to secure the

wires at the connector clamp.

4. Shorten unused wires appropriately and treat their ends with vinyl tape to prevent short

circuit.

Figure 4-10 Assembling 38P connector

Download from Www.Somanuals.com. All Manuals Search And Download.

Positioning guide pins

Guide pins of the connector are used to identify the mating receptacle. Position them shown

below.

Table 4-2 Guide pins and connector CN-E1

Clamping the cable (side at power supply unit)

Clamp the cable as shown in below.

Figure 4-11

Fabricating cable 10S1259 (connected terminal board TB-E1)

Figure 4-12 Fabricating cable 10S1259

Fabricating cable DPYCY-4

(connected to terminal board TB-E1)

Cable DPYCY-4

330

M4 (YEL) x 2

Armor

Anticorrosive

sheath

Armor

Vinyl

sheath

Conductor

Vinyl

sheath

S = 4.0 mm²

ø = 2.55 mm

Note: DPYCY-4 is Japan standard cable.

Use equivalent cable.

Figure 4-13 Fabricating cable DPYCY-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Fabricating cable 54-038-000-601/SC (CN-B2, CN-B3, CN-B4)

Figure 4-14 Fabricating cable 54-038-000-601/SC

Assembling 38P connector

1. Bundle the unused wires outside the connector case.

2. Fix the cover 1, taking heed of the cable outgoing direction.

3. Dress the wires and fix the cover 2 and 3. Use a fragment of cable sheath to secure the

wires at the connector clamp.

4. Shorten unused wires appropriately and treat their ends with vinyl tape to prevent short

circuit.

Figure 4-15 Assembling 38P connector

Positioning guide pins

Guide pins of the connector identify the mating receptacle. Position them as shown below.

Table 4-3 guide pins and connectors CN-B2, CN-B3, CN-B4

Download from Www.Somanuals.com. All Manuals Search And Download.

Clamping the cable

Secure the cable with the cable clamp.

Figure 4-16 Clamping the cable

Fabricating cable 10S1259 (connected to terminal board TB-B1)

Figure 4-17 Fabricating cable 10S1259

Fabricating cable 54-038-000-601/SC (CN-C2, CN-C3 and CN-C5),

00-8016-020-313-703V (CN-C4)

Figure 4-18 Fabricating cable 54-038-000-601/SC, 00-8016-020-000-703V

Download from Www.Somanuals.com. All Manuals Search And Download.

Assembling 38P connector

1. Bundle the unused wires outside the connector case.

2. Fix the cover 1, taking heed of the cable outgoing direction.

3. Dress the wires and fix the cover 2 and 3. Use a fragment of cable sheath to secure the

wires at the connector clamp.

4. Shorten unused wires appropriately and treat their ends with vinyl tape to prevent short

circuit.

Figure 4-19 Assembling 38P connector

Positioning guide pins

Guide pins of the connector identify the mating receptacle. Position them as below.

Table 4-4 Guide pins and connectors CN-C2, CN-C3, CN-C4, CN-C5

Clamping the cable

Clamp the anticorrosive sheath of the cable.

Figure 4-20 Clamping the cable

Download from Www.Somanuals.com. All Manuals Search And Download.

Fabricating cable connected to terminal board TB-D1 in Raise/

Lower Control Box

Figure 4-21 Fabricating cable connected to terminal board TB-D1

in Raise/Lower Control Box

Fabricating cable 10S1259

(connected to terminal board TB-D2 in Raise/Lower Control Box)

Figure 4-22 Fabricating cable 10S1259

Download from Www.Somanuals.com. All Manuals Search And Download.

4.5 Connection of Transducer Cables

The transducer cables are supplied with connectors. Plug them into the receptacles in the re-

ceiver unit, referring to the stickers on the cables.

Figure 4-23 Receiver unit, rear view

Lead the cable into the receiver unit and clamp it as follows.

Ground the cable by cable clamp.

Vinyl tape

1. Use the connector puller (supplied) to unplug connectors.

Connector Puller

(Code No. 100-008-460)

2. When one or some of the lead wires are severed near a connector, cut off all lead wires

connected to the connector and solder the "XH connector assembly" (type 10-145 (13P),

supplied as spare parts).

Download from Www.Somanuals.com. All Manuals Search And Download.

4.6 Connection of Interface Unit CS-120A

With connection of navigator, the Interface Unit CS-120A and electronic fishing equipment,

the function of the CSH-23/24 series is expanded to include true motion presentation, target

lock, echo sounder picture, FNZ marker presentation and digital indication of position, water

temperature and depth. This chapter provides the information for interfacing the CSH-23/24

series with external equipment.

Connections for true motion and target lock

Heading (digital) and speed (200 pulses/nm) data are required to provide the true motion

and target lock functions. Both data are fed to the display unit via Interface Unit CS-120A.

Basically, there are three methods to feed the data:

• Heading data is fed to J205 from A/D Converter AD-100 and the speed pulse data to

J206 from the speed log.

• Both heading and speed data are fed to J207 or J204 from the CIF line of the

CI-30/50/60.

• NMEA signal is fed to J208 (NMEA port) or J207 (CI/NMEA port).

J205

GYRO

J208

NMEA

A/D CONV.

AD-100

NMEA Signal

Heding Data

J207

CI/NMEA

NMEA Signal or

CIF Current Signal

INTERFACE

ELECTROMAGNETIC

LOG

(CS-120A)

J206

LOG

DOPPLER

SONAR

CURRENT

INDICATOR

DISPLAY UNIT

Speed Pulse Data

(CSH-830)

CN-A5

DOPPLER

SONAR

CIF 10S1148

(20m MAX)

J204

CIF

CURRENT

INDICATOR

J201

Heading Data

True Heading Data

Speed Data

Current Data

10S1258

Figure 4-24 Connection of external equipment to Interface Unit CS-120A

Note 1: AD-100 outputs two types of data. 200 ms interval is available.

Note 2: 200 pulses/mile ship’s speed data can be taken from a doppler sonar current

indicator.

Download from Www.Somanuals.com. All Manuals Search And Download.

There are six combinations of CIF/NMEA data input.

Combination NMEA port

J208

CIF port

J204

－

CI／NMEA port

J207

NMEA data

CIF current data

－

NMEA data

－

CIF data

－

NMEA data

－

CIF data

－

NMEA data

Note: NMEA port and CIF port are not fed a data at the same time. Either CIF current data

or NMEA data can be fed to CI/NMEA port.

Speed pulse signal

Do not feed Speed pulse data when speed data is fed from NMEA or CIF port and the

current indicator is chosen as own ship7s navigation data (refer to page 38). If they are fed

at the same time, the moving distance data will be doubled.

Receivable Data

•

Receivable Sentences from NMEA port

Depth Data：DBT、DPT

Temperature Data：MTW

Position fixing Data：GGA、RMC、GLL、RMA

Speed Data：VTG

Heading Data：VTG、HDT

Current Data：VHW、VDR、CUR

Time Data：ZDA

•

Receivable NMEA Sentences from CI/NMEA port

Same data as NMEA data is received. NMEA port has priority.

Receivable CIF data from CIF port

11：Time Data

21：Dead reckoning Position

24：Loran C fixing Position

28：GPS fixing Position

41：Speed and Heading Data for Dead reckoning

48：Speed and Heading Data from GPS fixing data

56：Current indicator

66：Current indicator

76：Current indicator

57：Depth Indicator

Data for Display

Heading, Speed, True Course Data

ID Number, Depth, Current Direction, Current Speed

Depth, Depth Information

58：Temperature Indicator

Temperature, Temperature Information

•

Receivable CIF data from CI/NMEA port

56：Current indicator

66：Current indicator

76：Current indicator

Data for Display

Heading, Speed, True Course Data

ID Number, Depth, Current Direction, Current Speed

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections for ES picture and FNZ markers

To provide echo sounder picture and FNZ markers, connect echo sounder to J203 and net

sonde to J202. The signals applied to J202 and J203 are

J202: Net sonde signal and trigger signal (keying pulse of echo sounder). A white line

signal from an echo sounder may be additionally applied as described on the next

page if the digital depth data is not available on J204.

J203: Echo signal and keying pulse from an echo sounder.

Connection 1: Displaying echo sounder picture

J203

(E/S)

E/S

VI-1100A

INTERFACE

UNIT

(CS-120A)

Connection 2: Displaying echo sounder picture and FNZ markers by one echo

sounder

FNZ JOINT BOX

(CS-170)

SONDE

J202 (SONDE)

J203 (E/S)

J701

TB-1

TB-2

(FNZ)

SONDE

(FNZ)

TB-1

TB-2

J705

SONDE

(FNZ)

INTERFACE

UNIT

(CS-120A)

E/S

VI-1100A

This method is used when the net sonde is installed and both echo sounder and net sonde

signals are taken from the same echo sounder. The net sonde signal is applied to both J202

and J203.

Connection 3: Displaying echo sounder picture and FNZ markers by separate

echo sounders

FNZ JOINT BOX

(CS-170)

SONDE

J202 (SONDE)

J203 (E/S)

J701

TB-1

TB-2

(FNZ)

SONDE

(FNZ)

J705

SONDE

(FNZ)

INTERFACE

UNIT

(CS-120A)

E/S

VI-1100A

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections for digital indication of position,

water temperature and depth

The data for these readouts are taken from the equipment shown in the table below and

input to J208 or J204. Input to J208 if the data is NMEA format, or to J204 if the data is CIF

format.

Data

Data Source

Position

Loran C navigator, GPS navigator

Temperature Indicator T-2000/TI-20, nav equipment or

color video sounder connected to temperature sensor

Color video sounder

Water Temperature

Depth

Note: When a sounder which has digital depth data output is not available, the white line

signal of a paper recording echo sounder can be used to provide digital depth

readout. Connect the echo sounder as shown below or as shown in connection 2 or

3 on previous pages and operate the echo sounder front panel controls so that the

white line is effected on the seabed contour.

Trigger (KP)

J202 (SONDE)

white line sig.

J701

J203 (E/S)

E/S

VI-1100A

CS-170

J705

TB-1

INTERFACE

UNIT

(CS-120A)

Wiring

Connect referring to the Interconnection Diagram at the back of this manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

Fabrication, assembling 10P and 7P connectors

8cm

2cm

1cm

BRAIDED

SHIELD

VINYL SHEATH

(OUTER)

VINYL SHEATH

(INNER)

EARTH WIRE

SOLDER UNUSED CORES

AND EARTH TO

BRAIDED SHIELD

CLAMP FIXING SCREW

SET SCREW

CLAMP

WIND SHIELDING TAPE

SOLDERING

VINYL SHEATH

(OUTER)

ARMOR

CONNECTOR CASE

SOLDERING-SIDE

CLAMP SHIELDING TAPE

WITH CONNECTOR CLAMP

FOR GROUNDING.

WIND VINYL TAPE

2cm

BRAIDED

SHIELD

VINYL SHEATH

SOLDERING-SIDE

EARTH

WIRE

CLAMP FIXING SCREW

SOLDER UNUSED CORES

AND EARTH WIRE TO

BRAIDED SHIELD

SET

CLAMP

SCREW

VINYL SHEATH

CONNECTOR CASE

WIND VINYL TAPE

Figure 4-30 Fabrication of 10P, 7P connectors

Download from Www.Somanuals.com. All Manuals Search And Download.

4.7 Connection of Sub-display Unit CSH-236/236F

(Option)

The Sub-Display Unit CSH-236/236F is the same as the Display Unit CSH-230/230F in terms

of outline dimension and control panel layout. It controls the sonar at a place remote from the

display unit while observing picture on the screen. One sub-display unit can be connected to

three display units.

Note: The Sub-Display Unit can be connected to CSH-23/23F only.

Connections

Refer to the interconnection diagram at the end of this manual.

Note: One sub-display unit can be connected to three sonars, but different models cannot be

connected.

DIP switch setting

Set DIP switch S1 on the RDCB Board (10P6724) in the sub-display unit as follows:

10P6724

CN-A3

(CH-3)

CN-A1

(CH-1)

CN-A2

(CH-2)

SW No.

Function

Used for

ON: Turning on sub-display unit automatically

turns on display unit.

Display unit on CH-1

Display unit on CH-2

Display unit on CH-3

Don’t set OFF because the system doesn’t work.

ON: Turning on display unit automatically

turns on sub-display unit.

OFF: Sub-display unit is not turned on when display

unit is turned on.

Display unit on CH-1

Display unit on CH-2

Display unit on CH-3

Not used.

Used in remote display unit. Set to ON in sub-display

unit.

Figure 4-31 DIP switch setting on RDCB board in the sub-display unit

Note: To have both the display unit and sub-display unit turned on when either unit is turned on,

turn on SW #1 and #4.

Download from Www.Somanuals.com. All Manuals Search And Download.

4.8 Synchronizing Transmission with Other Sonars,

Echo Sounders

To synchronize the transmission of the CSH-23/24 series sonars to that of other sonars or

echo sounders, wire units as follows.

Connections

Figure 4-33 Connections for synchronizing transmission with

echo sounder having current driven KP, voltage driven KP

Download from Www.Somanuals.com. All Manuals Search And Download.

Note: To output KP to other sonar or echo sounder, wire units as follows.

Figure 4-34 Connections for outputting KP to other sonar or echo sounder

Menu setting

Set polarity of the KP on the INIT SET/TEST menu. Set transmission cycle to 0 on data

setting window. Refer to the operator’s manual for operation on the menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

4.9 Interlocking Operation with Other Sonar

Functions (range, tilt, fish mark, etc.) and remote control may be mutually interlocked with

those on other sonars (CSH-23/24/73/83/84). For example, if the range is interlocked, changing

the range in one sonar automatically sets the other sonar to the same range. The functions to be

interlocked can be selected on the SYSTEM menu. See the operator’s manual for further de-

tails.

Connections for interlocking functions

Two sonars

Sonar 1

Sonar 2

CN-A4

>E> RD H

>F> RD C

>A> TD H

>B> TD C

TD H <A<

TD C <B<

RD H <E<

RD C <F<

Figure 4-35 connections for interlocking function of two sonars

Three sonars

Sonar 1

Sonar 2

TD RD

Sonar 3

Figure 4-36 Connections for interlocking functions of three sonars

DIP switch setting

Set ID code on DIP switch #1 to #3 on main panel. Any code is acceptable, provided that it is

not the same as that set on the other sonar.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connections for interlocking remote control

To control multiple display units by one remote control box, wire units as follows.

Connect same pin numbers.

NH-10P

Connect same pin numbers.

NH-10P

CN-A13

CN-A14

CN-A13 CN-A14

REMOTE

CONTROL

CONE Board

DISPLAY 3

CONE Board

DISPLAY 2

CONE Board

DISPLAY 1

Figure 4-37 Connections for interlocking remote control

Download from Www.Somanuals.com. All Manuals Search And Download.

5. CHANGING POWER SPECIFICATIONS

The display unit is set at the factory for connection to a ship’s mains of 110 VAC or 220 VAC.

To power it by 100 VAC or 220 VAC, use step-down transformer PT-400, change the trans-

former taps on the power supply unit as below and connect the ship’s mains directly.

The power supply unit has been

set for 100 VAC when delivered.

F Photo No.2017

Figure 5-1 Tap connections on the transformer in the power unit

Download from Www.Somanuals.com. All Manuals Search And Download.

6. ADJUSTMENT AND CHECK

6.1 Hull Unit Check

1. Press the ON switch to turn on the equipment. Con-

firm that the lamps above the ON and c switches

light.

TRANSDUCER

POWER

OFF ON

2. Confirm that the 5V and UP lamps on the raise/

lower control box are lit.

3. Remove the cover of the raise/lower control box

and check the following voltages:

Figure 6-1 Display unit front panel

Terminal

Terminal No.

Voltage

+12 V

TB-D1

7 – 8

1 – 2

2 – 3

1 – 3

180 VAC

360 VAC

TB-D2

4. In the raise/lower control box, turn the TEST/NOR-

MAL switch to TEST. Press the d switch to con-

firm that the transducer lowers. Also, while the

transducer is being lowered, check that the MD LED

lights when the MD L. SW kicks. Note that the MD

L. SW does not stop the transducer when the TEST/

NORMAL switch is in the TEST position.

Figure 6-2 Raise/Lower

control box

5. Press and release the d switch. Confirm that the transducer stops at the moment the switch

is released.

6. Press the d switch again. Confirm that the transducer stops at the moment the lower limit

switch kicks.

7. Confirm that the c switch operates in a similar manner.

8. Check that LEDs on the panel of the raise/lower control box light as follows:

1) UP, MD and DN LEDs light when corresponding limit switch kicks.

2) UP and DOWN LEDs light while UP and DOWN switches are pressed and extinguish

when switches are released.

9. Set the TEST/NORMAL switch to NORMAL.

10.At the display unit, press the d (mid position) switch. Confirm that the lamp above the

switch blinks while the transducer is being lowered, a short beep sounds when the mid limit

switch kicks, and the lamp lights when the transducer is fully lowered.

11.Press the d switch. Confirm that the lamp above the switch blinks while the transducer is

being lowered, a short beep sounds when the mid limit switch kicks, and the lamp lights

when the transducer is fully lowered.

Download from Www.Somanuals.com. All Manuals Search And Download.

12.Press the cswitch. Confirm that the lamp above the switch blinks while the transducer is

being raised, a short beep sounds when the mid limit switch kicks, and the lamp lights when

the transducer is fully raised.

13.Press the OFF switch. Confirm that the transducer is completely retracted and then the

power is turned off.

14.With the transducer lowered, confirm that the transducer is raised when cor OFF is pressed.

6.2 Heading Adjustment

When the BOW mark on the flange of the hull unit cannot be directed toward ship’s bow adjust

the heading so an echo which is dead ahead appears dead ahead on the display.

1. Locate a target in the bow direction (buoy, for example) and display it on a near range. If the

target appears at 12 o’clock the heading alignment is correct. If it does not go to step 2.

If target's on-screen

position is right of ship's

bow, hull unit heading

is skewed to left.

Buoy

Figure 6-3 Heading adjustment

2. Turn on the power while pressing and holding down the MENU key. The INIT SET/TEST

menu appears.

INIT SET/TEST MENU

Select item with dc[ \keys and press MENU key.

Press END key to close menu.

HEADING ADJ

SELF TEST

OTHERS

BAUD RATE

ECHO TEST

EXT KP

UNIT/LANGUAG

DEFAULTS

E/S NET REC

Figure 6-4 INIT SET/TEST menu

3. Select HEADING ADJ.

INIT SET/TEST MENU

Select item with dc[ \keys and press MENU key.

Press END key to close menu.

HEADING ADJ

359°

Setting range: 0° to 359°

Figure 6-5 HEADING ADJ menu

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Enter heading correction with ← or → referring to the table below for guidance.

Target Location

Correction Setting

Target displayed 30° to port

Set to 30°

Target displayed 30° to starboard Set to 330°

6.3 DIP Switch Setting in the Display Unit

Set the DIP switch on the display unit, referring to the table shown below.

1. Remove six screws from the main panel.

2. Unplug four connectors.

3. Set the DIP switch.

4. Reassemble display unit.

DSW Board (10P6722F)

Item

SW No.

Setting

ID Code for

Interlock

Function

Set ID code for interlock operation of

CSH-21/71/81/82/53/23/73/83 sonar. Any code is acceptable

unless it is used in other interlocked sonars.

Unit Code

OFF

CSH-58

(28 kHz)

CSH-53

(28 kHz)

CSH-53

(55 kHz)

CSH-23/24 CSH-73/ CSH-23F/23FL/

83/84

24F/24FL

Unit

EEPROM

Check

OFF

Check

OFF

Stand Alone

For factory use. Set to ON always.

PND Board (10switchP6714)

Item

SW No.

Setting

Display unit setting

OFF

For 21” CRT display unit

(CSH-24/24F/24FL/84)

For 15” CRT display unit

(CSH-23F/23FL/24F/24FL)

*: Set to OFF for the Processor unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

6.4 Setting and Adjustment of the Interface Unit

CS-120A

DIP switch setting

Navigation data and fishing data input from external equipment can be turned on or off by

DIP switches DP-1 and DP-2 on CPU II board 10P6871 in the Interface Unit CS-120A.

DP-2

CI/NMEA port Input format

Input format

CIF (Factory Setting)

NMEA

OFF

Changed the register R78 (47

when NMEA is selected.

Ω) to 470Ω on pcb 10P0047

Standard

Setting

-NMEA: 470

-CIF: 47

Interface board

(10P0047)

R78

DP-1

Own ship's navigation data (Gyrocompass, Speed log or Current indicator etc.)

Input Device

S1 S2

Select navigation device which feeds

navigation data for drawing ship's track

by S1 and S2.

OFF OFF

ON OFF

Gyrocompass, Sppeed log

GPS or DR *1

OFF

Current indicator

Gyrocompass, GPS *2

*1: GPS ship's speed/heading data from NMEA or CIF line, or dead reckoning

speed/heading data are used. Take care that heading data may have error if the

speed is lower than 0.2 kts.

*2: Courseline is plotted by using CIF or NMEA format speed data and Gyrocompass data.

Speed log is set by using GPS or Current Indicator.

Fix to "OFF"

Latitude/Longitude

OFF

Input Device

Loran C

GPS or DR *

Own ship's position data is selected with S3.

*: Data from GPS or DR is used (GPS has priority).

Download from Www.Somanuals.com. All Manuals Search And Download.

DP-1

Talker check (only for NMEA signal)

OFF

Talker is checked.

Talker is not checked.

Talker of GP, SD, VD, etc. is checked.

Depth (Echo sounder, Color Video Sounder, etc.)

Input Device

Echo Sounder *

OFF

CIF or NMEA line

Depth data is selected with S5.

*: Use this position for white line pulse when the depth data is taken from

an echo sounder. However late model FURUNO echo sounders do not

output white line pulse. Normally set to ON.

Interface unit (10P0047) adjustment

If the E/S picture on the screen does not have the desired coloration, perform the

adjustment as follows with the preset potentiometers on the I/O board in the interface unit.

R27

Interface board

R36

(10P0047)

R55

R56

S01

S02

Setting for DIP switch

S01:

The FNZ marker is plotted on the echo sounder picture with this

switch turned on when FNZ marker signal is fed to External Interface.

Factory setting is the “ON” position.

S02:

Selects the signal mode (AC or DC) according to the combined echo

sounder connected. Factory setting is the “AC” position.

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjustment of signal level (R36, R56)

1. Set the MODE switch to E/S.

2. Turn the potentiometer R36 to suppress a noise, and the potentiometer R56 so that the

color gradation of the E/S picture on the screen appears similar to the intensity

gradation of the combined E/S echogram.

Adjustment of white line inhibit time (R27)

In case digital depth data is not combined with the CS-120A, the white line signal from the

echo sounder is used for depth information. Potentiometer R27 cancels the white line pulse

for about 10 ms after transmission to avoid false depth indication caused by unwanted

noise in short ranges. Readjustment of potentiometer R27 is not required as long as

CSH-23/24 series indicates the correct depth. If does not, however turn R27 to the right.

Adjustment of white line output level (R55)

Improper setting of potentiometer R55 causes the seabed line to be painted in deep blue

due to the white line pulse. Adjust it so that the seabed line is painted in same color as

seabed.

Priority for data

The priority between ports, the category of data or formats is as follows. “1” has the highest

priority.

Basic priority

1. NMEA data > CIF data

2. NMEA data: NMEA port data > CI/NMEA port data

3. CIF data: CI/NMEA port data > CIF port data

Heading priority

1. Heading data from GYRO port

2. GP-HDT from NMEA port (GP-HDT: HDT sentence with Talker GP)

3. GP-HDT from CI/NMEA port

4. VD-VHW from NMEA port

5. VD-VHW from CI/NMEA port

6. VD-CUR from NMEA port

7. VD-CUR from CI/NMEA

8. CIF signal <66> from CI/NMEA port

9. CIF signal <66> from CIF port

GPS fixing position priority

Latitude and Longitude are set to GPS/DR with S3 on the DIP switch DP-1.

1. GP-GGA from NMEA port

2. GP-GGA from CI/NMEA port

3. GP-RMC from NMEA port

4. GP-RMC from CI/NMEA port

5. GP-GLL from NMEA port

6. GP-GLL from CI/NMEA port

7. <28> from CIF port

Download from Www.Somanuals.com. All Manuals Search And Download.

LC fixing position priority

Latitude and Longitude are set to LC with S3 on the DIP switch DP-1.

1. LC-RMA from NMEA

2. LC-RMA from CI/NMEA

3. <24> from CIF port

Depth priority

Depth is set to CIF/NMEA with S5 on the DIP switch DP-1.

1. SD-DPT from NMEA port

2. SD-DPT from CI/NMEA port

3. SD-DBT from NMEA port

4. SD-DBT from CI/NMEA port

5. <57> from CIF port

Ship’s movement data priority (data from GPS/DR)

Ship’s movement data is set to GPS·DR with S1/S2 on the DIP switch DP-1

1. GP-VTC from NMEA port

2. GP-VTC from CI/NMEA port

3. GP-RMC from NMEA port

4. GP-RMC from CI/NMEA port

5. <48> from CIF port

6. <41> from CIF port

Ship’s movement data priority (data from Current indicator)

Ship’s movement data is set to Current indicator with S1/S2 on the DIP switch DP-1

1. VD-VTG from NMEA port

2. VD-VTG from CI/NMEA port

3. VD-VHW from NMEA port

4. VD-VHW from CI/NMEA port

5. CIF signal <66> from CI/NMEA port

6. <66> from CIF port

Ship’s movement data priority (data from Gyro/Navigation)

Ship’s movement data is set to Gyrocompass/navigation with S1/S2 on the DIP switch

DP-1.

1. GP-VTG from NMEA port

2. GP-VTG from CI/NMEA port

3. GP-RMC from NMEA port

4. GP-RMC from CI/NMEA port

5. LC-VTG NMEA port

6. LC-VTG from CI/NMEA port

7. LC-RMA from NMEA port

8. LC-RMA from CI/NMEA port

9. <48> from CIF port

10. <44> from CIF port

Current data (Multi layer) priority

1. VD-CUR from NMEA port

2. VD-CUR from CI/NMEA port

3. CIF signal <76> from CI/NMEA port

4. <76> from CIF port

Current data (single layer) priority

1. VD-VDR from NMEA port

2. VD-VDR from CI/NMEA port

3. CIF signal <56> from CI/NMEA port

4. <56> from CIF port

Download from Www.Somanuals.com. All Manuals Search And Download.

7. PROCESSOR UNIT CSH-235/235F

(BLACKBOX TYPE FOR CSH-23/23F)

7.1

Installing the Unit

When selecting a mounting location, consider the following conditions:

• Place where operating personnel are able to control the unit easily while observing the

fishing ground or the area surrounding the vessel.

• Place not exposed to direct sunlight, water splashes or hot air.

• Place where maintenance and ventilation clearance shown in the outline drawings is

ensured.

• Observe the compass safe distances shown on page i to prevent interference to a

magnetic compass.

Mounting procedure

1. Remove the mounting base by unscrewing the two bolts at the front bottom.

2. Fix the mounting base to the table or deck by using six self-tapping screws 6x20

(supplied).

3. Place the unit on the mounting base, slide it forward and then fasten it to the mounting

base with two bolts.

(133)

)

(90

6-φ8 Fixing holes

210±

210±1

Remove two bolts

Processor unit

Top view

7.2

Monitor

Use a commercially available monitor having the specifications shown below.

• Signal:

• Synchro. signal:

Analog RGB, 0 – 0.9 V, Positive, 75 Ω

Horizontal, TTL level, 31.687 kHz 4 Hz, 75 Ω

Vertical, TTL level, 60.111 Hz 0.0007 Hz, 75 Ω

VGA, 640 x 481

• Resolution:

Mount the monitor in portrait orientation. Note that FURUNO monitor model MU-151C can be

used in portrait orientation.

Download from Www.Somanuals.com. All Manuals Search And Download.

7.3

Connecting cables

Fabricate the cables as shown in the section “4.4 Fabricating Cable, Assembling connectors.”

Connect the cables, referring to the interconnection diagrams at the back of this manual.

Port for monitor

Cable entrance

DISPLAY

RGB port panel

D-sub

15P

Power supply port

BNC

FUSE

100 VAC

50/60Hz

GND

Ground terminal

Processor unit (rear panel)

Protective earth

Attach protective earth cable (IV-8sq, shipyard supply) between the GND terminal of the

processor unit and ship’s body.

CAUTION

Securely attach protective earth

to the ship's body.

The protective earth is required

to prevent electrical shock.

Connectors for Monitor

There are two kinds of video signal ports: D-sub connector (default) and BNC connectors.

• D-sub: Use interconnection cable 3COX-2P-6C (5 m or 10 m) or equivalent commercially

available cable.

• BNC connector: Use five 75 Ω coaxial cables (shipyard supply). The coaxial cables are

preferred in case of longer than 10 m cable run between the processor unit and monitor.

The following modification is required to use the BNC connectors.

1. Dismount the RGB port panel at the rear of the processor unit.

2. Confirming the label attached to each BNC connector, connect each connector to its

corresponding port.

3. Mount the RGB port panel.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONE board (10P6711)

Screw (4 pcs)

J21

BNC connector

Replace each

BCN connector

to the same

label port.

RGB port panel

Processor unit (right side, cover removed)

Download from Www.Somanuals.com. All Manuals Search And Download.

A-1

1/1

10CJ-X-9851 -1

ＰＡＣＫＩＮＧ　ＬＩＳＴ

CSH-235/235K/235F/535/585/735/835

N A M E

DESCRIPTION/CODE №

O U T L I N E

Q'TY

ユニット

UNIT

CSH-235

操作制御部

PROCESSOR UNIT

000-070-191

SP10-03201

006-030-590

CP10-06301

006-030-600

予備品

SPARE PARTS

工事材料

INSTALLATION MATERIALS

1.ｺ-ﾄﾞ番号末尾の[**]は、選択品の代表型式/ｺｰﾄﾞを表します。

CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF REPRESENTATIVE MATERIAL.

（略図の寸法は、参考値です。 DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10CJ-X-9851

Download from Www.Somanuals.com. All Manuals Search And Download.

A-2

1/1

006-030-590

SP10-03201

10CJ-X-9301 -1

BOX NO.

CODE NO.

TYPE

SETS PER

VESSEL

SHIP NO.

SPARE PARTS LIST FOR

U S E

QUANTITY

WORKING

PER PER

REMARKS/CODE NO.

DWG. NO.

ITEM

NO.

NAME OF

PART

OUTLINE

TYPE NO.

SPARE

SET VES

ﾋｭｰｽﾞ

FUSE

FGBO-A 5A

AC125V

000-549-064

1/1

MFR'S NAME

DWG NO.

FURUNO ELECTRIC CO.,LTD.

10CJ-X-9301

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING　FOR REFERENCE ONLY.）

Download from Www.Somanuals.com. All Manuals Search And Download.

A-3

CODE NO.

TYPE

006-030-600

CP10-06301

10CJ-X-9401 -0

1/1

工事材料表

INSTALLATION MATERIALS

数量

Q'TY

番号

NO.

名　　称

NAME

型名／規格

DESCRIPTIONS

6X20 SUS304

略　　図

OUTLINE

用途／備考

REMARKS

+ﾄﾗｽﾀｯﾋﾟﾝﾈｼﾞ　1種

SELF-TAPPING SCREW

CODE NO. 000-802-084

NCS-253-P

ｺﾈｸﾀ(NCS)

CONNECTOR(NCS)

CODE NO. 000-506-503

10CJ-X-9401

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

Download from Www.Somanuals.com. All Manuals Search And Download.

A-4

Download from Www.Somanuals.com. All Manuals Search And Download.

A-5

Download from Www.Somanuals.com. All Manuals Search And Download.

A-6

000-070-208

SP10-03300

10CJ-X-9302 -0

1/1

CODE NO.

TYPE

BOX NO.

SETS PER

VESSEL

SHIP NO.

SPARE PARTS LIST FOR

U S E

QUANTITY

WORKING

PER PER

REMARKS/CODE NO.

DWG. NO.

ITEM

NO.

NAME OF

PART

OUTLINE

SPARE

TYPE NO.

SET VES

管入りﾋｭｰｽﾞ

FUSE

指示装置用

FGB01 30A

AC250V

FOR DISPLAY UNIT

000-549-086

受信装置用

XHｺﾈｸﾀ組品

10-145(13P)

XH CONNECTOR

ASSY,

FOR RECEIVER UNIT

006-947-380

受信装置用

ｺﾈｸﾀ抜き工具

10-026-6901-0

CONNECTOR

PULLER

FOR RECEIVER UNIT

100-008-460

送信装置用

ﾋｭｰｽﾞ

FUSE

FGBO-A 2A

AC125V

FOR TRANSMITTER UNIT

000-549-062

1/1

MFR'S NAME

DWG NO.

10CJ-X-9302

FURUNO ELECTRIC CO.,LTD.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

Download from Www.Somanuals.com. All Manuals Search And Download.

A-7

000-070-209

SP10-03400

10CJ-X-9303 -0

1/1

CODE NO.

TYPE

BOX NO.

SETS PER

VESSEL

SHIP NO.

SPARE PARTS LIST FOR

U S E

QUANTITY

WORKING

PER PER

REMARKS/CODE NO.

DWG. NO.

ITEM

NO.

NAME OF

PART

OUTLINE

SPARE

TYPE NO.

SET VES

管入りﾋｭｰｽﾞ

FUSE

指示装置用

FGB01 30A

AC250V

FOR DISPLAY UNIT

000-549-086

受信装置用

XHｺﾈｸﾀ組品

10-145(13P)

XH CONNECTOR

ASSY,

FOR RECEIVER UNIT

006-947-380

受信装置用

ｺﾈｸﾀ抜き工具

10-026-6901-0

FGBO 5A AC250V

CONNECTOR

PULLER

FOR RECEIVER UNIT

100-008-460

送信装置用

ﾋｭｰｽﾞ

FUSE

FOR TRANSMITTER UNIT

000-549-022

1/1

MFR'S NAME

DWG NO.

10CJ-X-9303

FURUNO ELECTRIC CO.,LTD.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

Download from Www.Somanuals.com. All Manuals Search And Download.

A-8

CODE NO.

TYPE

006-989-010-00

CP10-02710

10BW-X-9401 -9

1/4

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

DESCRIPTIONS

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

外部ｲﾝﾀｰﾌｪｰｽ工材

FOR INTERFACE UNIT

ｱｰｽ線組品

CS-120-C

CODE NO.

GROUNDING WIRE

006-937-660-00

008016-038-313761HVF

外部ｲﾝﾀｰﾌｪｰｽ工材　

FOR INTERFACE UNIT

ｺﾈｸﾀ(8016）

00-8016-038-313761HV

CONNECTOR(8016)

000-159-017-10

000-127-234-00

CODE NO.

外部ｲﾝﾀｰﾌｪｰｽ工材　

FOR INTERFACE UNIT

貼りﾏｰｸ.J201.

STICKER.J201.

10-018-5022

CODE NO.

181-850-220-00

外部ｲﾝﾀｰﾌｪｰｽ工材　

FOR INTERFACE UNIT

ｺﾈｸﾀ(54)

54-038-000-601/SC

CODE NO.

CONNECTOR(54)

000-132-081-00

外部ｲﾝﾀｰﾌｪｰｽ工材　

FOR INTERFACE UNIT

ｺﾝﾀｸﾄﾋﾟﾝ（8017)

60-8017-0313-00-339

CONTACT PIN (8017)

CODE NO.

000-519-542-00

RM15TP-2PA(71)

外部ｲﾝﾀｰﾌｪｰｽ工材　

FOR INTERFACE UNIT

ｺﾈｸﾀ(RM)

RM15TP-2PA

CONNECTOR(RM)

000-159-835-10

000-503-314-00

CODE NO.

外部ｲﾝﾀｰﾌｪｰｽ工材　

FOR INTERFACE UNIT

ｺﾈｸﾀ(SRCN)

SRCN2A16-7P

CODE NO.

CONNECTOR(SRCN)

000-508-652-00

外部ｲﾝﾀｰﾌｪｰｽ工材　

FOR INTERFACE UNIT

ｺﾈｸﾀ(SRCN）

SRCN6A16-10P

CODE NO.

CONNECTOR(SRCN)

000-508-663-00

外部ｲﾝﾀｰﾌｪｰｽ工材　

FOR INTERFACE UNIT

ｺﾈｸﾀ(SRCN）

SRCN6A16-7P

CODE NO.

CONNECTOR(SRCN)

000-508-662-00

008016-038-313761HVF

指示装置工材　　　

FOR DISPLAY UNIT

ｺﾈｸﾀ(8016）

00-8016-038-313761HV

CONNECTOR(8016)

000-159-017-10

000-127-234-00

CODE NO.

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10BW-X-9401

C1286-M01-H

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-9

CODE NO.

TYPE

006-989-010-00

CP10-02710

10BW-X-9401 -9

2/4

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

DESCRIPTIONS

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

指示装置工材　　　

FOR DISPLAY UNIT

ｸｰﾗｰﾊﾟﾃ

200Gｲﾘ　ｼﾛｲﾛ

CODE NO.

COOLER PUTTY

000-807-621-00

指示装置工材　　　

FOR DISPLAY UNIT

ｲﾗｯｸｽﾁｭｰﾌﾞ(A)

4.0X0.3　ｷｲﾛ　*5CM*

CODE NO.

INSULATION TUBE(A)

000-100-923-00

NCS-252-P *ROHS*

指示装置工材　　　

FOR DISPLAY UNIT

ｺﾈｸﾀ(NCS)

CONNECTOR

NCS-252-P

000-160-150-10

CODE NO.

000-506-501-10

指示装置工材　　　

FOR DISPLAY UNIT

ｺﾈｸﾀ(NCS)

NCS-253-P

CODE NO.

CONNECTOR(NCS)

000-506-503-10

指示装置工材　　　

FOR DISPLAY UNIT

ｱｰｽ板

WEA-1004-0

CODE NO.

COPPER STRAP

500-310-040-00

受信装置工材　　　

FOR RECEIVER UNIT

ｺﾈｸﾀ(8016)

CONNECTOR

00-8016-020-313-703V

CODE NO.

000-111-143-00

受信装置工材　　　

FOR RECEIVER UNIT

P貼りﾏｰｸ.11.

P STICKER.11.

10-026-0619-0

CODE NO.

100-014-880-00

受信装置工材　　　

FOR RECEIVER UNIT

ｺﾈｸﾀ(54)

54-038-000-601/SC

CONNECTOR(54)

CODE NO.

000-132-081-00

受信装置工材　　　

FOR RECEIVER UNIT

ｺﾝﾀｸﾄﾋﾟﾝ（8017)

60-8017-0313-00-339

114

CONTACT PIN (8017)

CODE NO.

000-519-542-00

受信装置工材　　　

FOR RECEIVER UNIT

ｱｲﾎﾞﾙﾄ

M10 SS41 MFNI2

EYE-BOLT

CODE NO.

000-862-506-00

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10BW-X-9401

C1257-M02-D

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-10

CODE NO.

TYPE

006-989-010-00

CP10-02710

10BW-X-9401 -9

3/4

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

DESCRIPTIONS

受信装置工材　　　

FOR RECEIVER UNIT

ﾐｶﾞｷ平座金

M10 SS41 MFZN2-B

CODE NO.

FLAT WASHER

000-864-191-00

受信装置工材　　　

FOR RECEIVER UNIT

ｱｰｽ板

WEA-1004-0

CODE NO.

COPPER STRAP

500-310-040-00

受信装置工材　　　

FOR RECEIVER UNIT

ｼｰﾙﾄﾞｽﾘｰﾌﾞ

ZSK-06HF　0.055M

CODE NO.

SHIELD SLEEVE

000-809-085-00

上下装置工材　　　

FOR HULL UNIT

圧着端子

FV1.25-3.7 ｱｶ

CODE NO.

CRIMP-ON LUG

000-108-699-00

上下装置工材　　　

FOR HULL UNIT

圧着端子

FV1.25-M4　ｱｶ

CODE NO.

CRIMP-ON LUG

000-536-715-00

上下装置工材　　　

FOR HULL UNIT

圧着端子

FV5.5-4

CRIMP-ON LUG

CODE NO.

000-538-123-00

送振装置工材　　　

FOR TRANSMITTER UNIT

貼りﾏｰｸ

STICKER

10-026-5002-0

CODE NO.

100-004-870-00

送振装置工材　　　

FOR TRANSMITTER UNIT

ｺﾈｸﾀ(54)

54-038-000-601/SC

CODE NO.

CONNECTOR(54)

000-132-081-00

送振装置工材　　　

FOR TRANSMITTER UNIT

ｺﾝﾀｸﾄﾋﾟﾝ（8017)

60-8017-0313-00-339

120

CONTACT PIN (8017)

CODE NO.

000-519-542-00

送振装置工材　　　

FOR TRANSMITTER UNIT

圧着端子

FV1.25-M4　ｱｶ

CRIMP-ON LUG

CODE NO.

000-536-715-00

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10BW-X-9401

C1257-M03-D

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-11

CODE NO.

TYPE

006-989-010-00

CP10-02710

10BW-X-9401 -9

4/4

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

DESCRIPTIONS

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

送振装置工材　　　

FOR TRANSMITTER UNIT

圧着端子

FV5.5-4

CRIMP-ON LUG

CODE NO.

000-538-123-00

000-800-729-00

送振装置工材　　　

FOR TRANSMITTER UNIT

ﾎｰﾙﾌﾟﾗｸﾞ

NO.4567

HOLE PLUG

CODE NO.

送振装置工材　　　

FOR TRANSMITTER UNIT

ｱｰｽ板

WEA-1004-0

CODE NO.

COPPER STRAP

500-310-040-00

電源装置工材

FOR POWER UNIT

貼りﾏｰｸ.1.

STICKER.1.

10-026-7018-0

CODE NO.

100-008-630-00

電源装置工材

FOR POWER UNIT

ｺﾈｸﾀ(54)

54-038-000-601/SC

CODE NO.

CONNECTOR(54)

000-132-081-00

電源装置工材

FOR POWER UNIT

ｺﾝﾀｸﾄﾋﾟﾝ（8017)

60-8017-0313-00-339

CONTACT PIN (8017)

CODE NO.

000-519-542-00

電源装置工材

FOR POWER UNIT

圧着端子

FV1.25-M4　ｱｶ

CRIMP-ON LUG

CODE NO.

000-536-715-00

電源装置工材

FOR POWER UNIT

圧着端子

FV5.5-4

CRIMP-ON LUG

CODE NO.

000-538-123-00

電源装置工材

FOR POWER UNIT

ﾎｰﾙﾌﾟﾗｸﾞ

NO.4567

HOLE PLUG

CODE NO.

000-800-729-00

電源装置工材

ｱｰｽ板

FOR POWER UNIT

WEA-1004-0

COPPER STRAP

CODE NO.

500-310-040-00

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10BW-X-9401

C1257-M04-D

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-12

Download from Www.Somanuals.com. All Manuals Search And Download.

A-13

CODE NO.

TYPE

006-959-800-00

CP10-03410

10CC-X-9401 -3

1/5

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

DESCRIPTIONS

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

外部ｲﾝﾀｰﾌｪｲｽﾕﾆｯﾄ用　

　FOR DATA INTERFACE

UNIT

ｺﾈｸﾀ(SRCN)

SRCN2A16-7P

CODE NO.

CONNECTOR(SRCN)

000-508-652-00

008016-038-313761HVF

外部ｲﾝﾀｰﾌｪｲｽﾕﾆｯﾄ用　

FOR DATA INTERFACE

UNIT

ｺﾈｸﾀ(8016）

00-8016-038-313761HV

CONNECTOR(8016)

000-159-017-10

000-127-234-00

CODE NO.

外部ｲﾝﾀｰﾌｪｲｽﾕﾆｯﾄ用　

FOR DATA INTERFACE

UNIT

貼りﾏｰｸ.J201.

STICKER.J201.

10-018-5022

CODE NO.

181-850-220-00

外部ｲﾝﾀｰﾌｪｲｽﾕﾆｯﾄ用　

FOR DATA INTERFACE

UNIT

ｺﾈｸﾀ(54)

54-038-000-601/SC

CODE NO.

CONNECTOR(54)

000-132-081-00

外部ｲﾝﾀｰﾌｪｲｽﾕﾆｯﾄ用　

FOR DATA INTERFACE

UNIT

ｺﾝﾀｸﾄﾋﾟﾝ（8017)

60-8017-0313-00-339

CONTACT PIN (8017)

CODE NO.

000-519-542-00

外部ｲﾝﾀｰﾌｪｲｽﾕﾆｯﾄ用　

FOR DATA INTERFACE

UNIT

ｱｰｽ線組品

CS-120-C

GROUNDING WIRE

CODE NO.

006-937-660-00

RM15TP-2PA(71)

外部ｲﾝﾀｰﾌｪｲｽﾕﾆｯﾄ用　

FOR DATA INTERFACE

UNIT

ｺﾈｸﾀ(RM)

RM15TP-2PA

CONNECTOR(RM)

000-159-835-10

000-503-314-00

CODE NO.

外部ｲﾝﾀｰﾌｪｲｽﾕﾆｯﾄ用　

FOR DATA INTERFACE

UNIT

ｺﾈｸﾀ(SRCN）

SRCN6A16-10P

CODE NO.

CONNECTOR(SRCN)

000-508-663-00

外部ｲﾝﾀｰﾌｪｲｽﾕﾆｯﾄ用　

FOR DATA INTERFACE

UNIT

ｺﾈｸﾀ(SRCN）

SRCN6A16-7P

CODE NO.

CONNECTOR(SRCN)

000-508-662-00

008016-038-313761HVF

指示装置用　　　　

FOR DISPLAY UNIT

ｺﾈｸﾀ(8016）

00-8016-038-313761HV

CONNECTOR(8016)

000-159-017-10

000-127-234-00

CODE NO.

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10CC-X-9401

C1292-M01-B

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-14

CODE NO.

TYPE

006-959-800-00

CP10-03410

10CC-X-9401 -3

2/5

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

DESCRIPTIONS

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

指示装置用　　　　

FOR DISPLAY UNIT

M8化粧ﾋﾞｽ

10-054-1144-0

CODE NO.

PANEL SCREW

100-195-970-00

指示装置用　　　　

FOR DISPLAY UNIT

ｸｰﾗｰﾊﾟﾃ

200Gｲﾘ　ｼﾛｲﾛ

CODE NO.

COOLER PUTTY

000-807-621-00

指示装置用　　　　

FOR DISPLAY UNIT

ｲﾗｯｸｽﾁｭｰﾌﾞ(A)

4.0X0.3　ｷｲﾛ　*5CM*

CODE NO.

INSULATION TUBE(A)

000-100-923-00

NCS-252-P *ROHS*

指示装置用　　　　

FOR DISPLAY UNIT

ｺﾈｸﾀ(NCS)

CONNECTOR

NCS-252-P

000-160-150-10

CODE NO.

000-506-501-10

指示装置用　　　　

FOR DISPLAY UNIT

ｺﾈｸﾀ(NCS)

NCS-253-P

CODE NO.

CONNECTOR(NCS)

000-506-503-10

指示装置用　　　　

FOR DISPLAY UNIT

ｱｰｽ板

WEA-1004-0

CODE NO.

COPPER STRAP

500-310-040-00

受信装置用　　　　　

FOR RECEIVER UNIT

ｺﾈｸﾀ(8016)

CONNECTOR

00-8016-020-313-703V

CODE NO.

000-111-143-00

受信装置用　　　　　

FOR RECEIVER UNIT

P貼りﾏｰｸ.11.

P STICKER.11.

10-026-0619-0

CODE NO.

100-014-880-00

受信装置用　　　　　

FOR RECEIVER UNIT

ｺﾈｸﾀ(54)

54-038-000-601/SC

CONNECTOR(54)

CODE NO.

000-132-081-00

受信装置用　　　　　

FOR RECEIVER UNIT

ｺﾝﾀｸﾄﾋﾟﾝ（8017)

60-8017-0313-00-339

114

CONTACT PIN (8017)

CODE NO.

000-519-542-00

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10CC-X-9401

C1292-M02-B

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-15

CODE NO.

TYPE

006-959-800-00

CP10-03410

10CC-X-9401 -3

3/5

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

DESCRIPTIONS

受信装置用　　　　　

FOR RECEIVER UNIT

ｱｲﾎﾞﾙﾄ

M10 SS41 MFNI2

CODE NO.

EYE-BOLT

000-862-506-00

受信装置用　　　　　

FOR RECEIVER UNIT

ﾐｶﾞｷ平座金

FLAT WASHER

M10 SS41 MFZN2-B

CODE NO.

000-864-191-00

受信装置用　　　　　

FOR RECEIVER UNIT

ｱｰｽ板

WEA-1004-0

CODE NO.

COPPER STRAP

500-310-040-00

受信装置用　　　　　

FOR RECEIVER UNIT

ｼｰﾙﾄﾞｽﾘｰﾌﾞ

ZSK-06HF　0.055M

CODE NO.

SHIELD SLEEVE

000-809-085-00

上下装置用　　　　　

FOR HULL UNIT

圧着端子

FV1.25-3.7 ｱｶ

CODE NO.

CRIMP-ON LUG

000-108-699-00

上下装置用　　　　　

FOR HULL UNIT

圧着端子

FV1.25-M4　ｱｶ

CODE NO.

CRIMP-ON LUG

000-536-715-00

上下装置用　　　　　

FOR HULL UNIT

圧着端子

FV5.5-4

CRIMP-ON LUG

CODE NO.

000-538-123-00

送振装置用　　　　

FOR TRANSMITTER UNIT

ｺﾝﾀｸﾄﾋﾟﾝ（8017)

60-8017-0313-00-339

120

CONTACT PIN (8017)

CODE NO.

000-519-542-00

送振装置用　　　　

FOR TRANSMITTER UNIT

圧着端子

FV1.25-M4　ｱｶ

CRIMP-ON LUG

CODE NO.

000-536-715-00

送振装置用　　　　

FOR TRANSMITTER UNIT

圧着端子

FV5.5-4

CRIMP-ON LUG

CODE NO.

000-538-123-00

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10CC-X-9401

C1292-M03-B

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-16

CODE NO.

TYPE

006-959-800-00

CP10-03410

10CC-X-9401 -3

4/5

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

DESCRIPTIONS

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

送振装置用　　　　

FOR TRANSMITTER UNIT

ﾎｰﾙﾌﾟﾗｸﾞ

NO.4567

CODE NO.

HOLE PLUG

000-800-729-00

送振装置用　　　　

FOR TRANSMITTER UNIT

ｱｰｽ板

WEA-1004-0

CODE NO.

COPPER STRAP

500-310-040-00

送振装置用　　　　　

FOR TRANSMITTER UNIT

ｺﾈｸﾀ(54)

54-038-000-601/SC

CODE NO.

CONNECTOR(54)

000-132-081-00

送振装置用　　　　

FOR TRANSMITTER UNIT

貼りﾏｰｸ

STICKER

10-026-5002-0

CODE NO.

100-004-870-00

電源装置用　　　　　

FOR POWER SUPPLY UNIT

貼りﾏｰｸ.1.

STICKER.1.

10-026-7018-0

CODE NO.

100-008-630-00

電源装置用　　　　　

FOR POWER SUPPLY UNIT

ｺﾈｸﾀ(54)

54-038-000-601/SC

CODE NO.

CONNECTOR(54)

000-132-081-00

電源装置用　　　　　

FOR POWER SUPPLY UNIT

ｺﾝﾀｸﾄﾋﾟﾝ（8017)

60-8017-0313-00-339

CONTACT PIN (8017)

CODE NO.

000-519-542-00

電源装置用　　　　　

FOR POWER SUPPLY UNIT

圧着端子

FV1.25-M4　ｱｶ

CRIMP-ON LUG

CODE NO.

000-536-715-00

電源装置用　　　　　

FOR POWER SUPPLY UNIT

圧着端子

FV5.5-4

CRIMP-ON LUG

CODE NO.

000-538-123-00

電源装置用　　　　　

FOR POWER SUPPLY UNIT

ﾎｰﾙﾌﾟﾗｸﾞ

NO.4567

HOLE PLUG

CODE NO.

000-800-729-00

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10CC-X-9401

C1292-M04-B

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-17

CODE NO.

TYPE

006-959-800-00

CP10-03410

10CC-X-9401 -3

5/5

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

DESCRIPTIONS

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

電源装置用　　　　　

FOR POWER SUPPLY UNIT

ｱｰｽ板

COPPER STRAP

WEA-1004-0

CODE NO.

500-310-040-00

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10CC-X-9401

C1292-M05-B

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-18

CODE NO.

TYPE

006-030-650-00

CP10-06410

10CJ-X-9402 -1

1/4

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

DESCRIPTIONS

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

外部ｲﾝﾀｰﾌｪｲｽ工材　　

FOR INTERFACE UNIT

貼りﾏｰｸ.J201.

STICKER.J201.

10-018-5022

CODE NO.

181-850-220-00

外部ｲﾝﾀｰﾌｪｲｽ工材　　

FOR INTERFACE UNIT

ｺﾝﾀｸﾄﾋﾟﾝ（8017)

60-8017-0313-00-339

CONTACT PIN (8017)

CODE NO.

000-519-542-00

RM15TP-2PA(71)

外部ｲﾝﾀｰﾌｪｲｽ工材　　

FOR INTERFACE UNIT

ｺﾈｸﾀ(RM)

RM15TP-2PA

CONNECTOR(RM)

000-159-835-10

000-503-314-00

CODE NO.

外部ｲﾝﾀｰﾌｪｲｽ工材　　

FOR INTERFACE　UNIT

ｺﾈｸﾀ(SRCN)

SRCN2A16-7P

CODE NO.

CONNECTOR(SRCN)

000-508-652-00

外部ｲﾝﾀｰﾌｪｲｽ工材　　

FOR INTERFACE UNIT

ｺﾈｸﾀ(SRCN）

SRCN6A16-10P

CODE NO.

CONNECTOR(SRCN)

000-508-663-00

外部ｲﾝﾀｰﾌｪｲｽ工材　　

FOR INTERFACE UNIT

ｺﾈｸﾀ(SRCN）

SRCN6A16-7P

CODE NO.

CONNECTOR(SRCN)

000-508-662-00

008016-038-313761HVF

外部ｲﾝﾀｰﾌｪｲｽ工材　

FOR INTERFACE UNIT

ｺﾈｸﾀ(8016）

00-8016-038-313761HV

CONNECTOR(8016)

000-159-017-10

000-127-234-00

CODE NO.

外部ｲﾝﾀｰﾌｪｲｽ工材　

FOR INTERFACE UNIT

ｺﾈｸﾀ(54)

54-038-000-601/SC

CODE NO.

CONNECTOR(54)

000-132-081-00

外部ｲﾝﾀｰﾌｪｰｽ工材　

FOR INTERFACE UNIT

ｱｰｽ線組品

CS-120-C

CODE NO.

GROUNDING WIRE

006-937-660-00

受信装置工材　　　　

FOR RECEIVER UNIT

P貼りﾏｰｸ.11.

P STICKER.11.

10-026-0619-0

CODE NO.

100-014-880-00

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10CJ-X-9402

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-19

CODE NO.

TYPE

006-030-650-00

CP10-06410

10CJ-X-9402 -1

2/4

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

DESCRIPTIONS

受信装置工材　　　　

FOR RECEIVER UNIT

ｺﾝﾀｸﾄﾋﾟﾝ（8017)

60-8017-0313-00-339

114

CONTACT PIN (8017)

CODE NO.

000-519-542-00

受信装置工材　　　　

FOR RECEIVER UNIT

ｱｲﾎﾞﾙﾄ

M10 SS41 MFNI2

EYE-BOLT

CODE NO.

000-862-506-00

受信装置工材　　　　

FOR RECEIVER UNIT

ﾐｶﾞｷ平座金

FLAT WASHER

M10 SS41 MFZN2-B

CODE NO.

000-864-191-00

受信装置工材　　　　

FOR RECEIVER UNIT

ｱｰｽ板

WEA-1004-0

COPPER STRAP

CODE NO.

500-310-040-00

受信装置工材　　　　

FOR RECEIVER UNIT

ｼｰﾙﾄﾞｽﾘｰﾌﾞ

ZSK-06HF　0.055M

SHIELD SLEEVE

CODE NO.

000-809-085-00

受信装置工材　　

FOR TRANSCEIVER UNIT

ｺﾈｸﾀ(8016)

CONNECTOR

00-8016-020-313-703V

CODE NO.

000-111-143-00

受信装置工材　　　

FOR RECEIVER UNIT

ｺﾈｸﾀ(54)

54-038-000-601/SC

CONNECTOR(54)

CODE NO.

000-132-081-00

上下装置工材　　　　

FOR HULL UNIT

圧着端子

FV1.25-M4　ｱｶ

CRIMP-ON LUG

CODE NO.

000-536-715-00

上下装置工材　　　　

FOR HULL UNIT

圧着端子

FV5.5-4

CRIMP-ON LUG

CODE NO.

000-538-123-00

上下装置工材　　　　

FOR RECEIVER UNIT

圧着端子

FV1.25-3.7 ｱｶ

CRIMP-ON LUG

CODE NO.

000-108-699-00

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10CJ-X-9402

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-20

CODE NO.

TYPE

006-030-650-00

CP10-06410

10CJ-X-9402 -1

3/4

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

DESCRIPTIONS

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

送信装置工材　

FOR TRaNSMITTER UNIT

貼りﾏｰｸ

10-026-5002-0

CODE NO.

STICKER

100-004-870-00

送信装置工材

圧着端子

FOR TRANSMITTER UNIT

FV1.25-M4　ｱｶ

CODE NO.

120

CRIMP-ON LUG

000-536-715-00

送信装置工材　　　　

FOR TRANSMITTER UNIT

ｺﾝﾀｸﾄﾋﾟﾝ（8017)

60-8017-0313-00-339

CONTACT PIN (8017)

CODE NO.

000-519-542-00

送信装置工材　　　　

FOR TRANSMITTER UNIT

圧着端子

FV5.5-4

CRIMP-ON LUG

CODE NO.

000-538-123-00

送信装置工材　　　　

FOR TRANSMITTER UNIT

ﾎｰﾙﾌﾟﾗｸﾞ

NO.4567

HOLE PLUG

CODE NO.

000-800-729-00

送信装置工材　　　　

FOR TRANSMITTER UNIT

ｱｰｽ板

WEA-1004-0

COPPER STRAP

CODE NO.

500-310-040-00

送信装置工材　　　

FOR TRANSMITTER UNIT

ｺﾈｸﾀ(54)

54-038-000-601/SC

CONNECTOR(54)

CODE NO.

000-132-081-00

電源装置工材

圧着端子

FOR POWER UNIT

FV5.5-4

CRIMP-ON LUG

CODE NO.

000-538-123-00

電源装置工材

FOR POWER UNIT

ｺﾈｸﾀ(54)

54-038-000-601/SC

CONNECTOR(54)

CODE NO.

000-132-081-00

電源装置工材　　　　

FOR POWER UNIT

貼りﾏｰｸ.1.

STICKER.1.

10-026-7018-0

CODE NO.

100-008-630-00

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10CJ-X-9402

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-21

CODE NO.

TYPE

006-030-650-00

CP10-06410

10CJ-X-9402 -1

4/4

工事材料表

INSTALLATION MATERIALS

数量

番号

NO.

名　　称

NAME

型名／規格

略　　図

OUTLINE

用途／備考

REMARKS

Q'TY

DESCRIPTIONS

電源装置工材　　　　

FOR POWER UNIT

ｺﾝﾀｸﾄﾋﾟﾝ（8017)

60-8017-0313-00-339

CONTACT PIN (8017)

CODE NO.

000-519-542-00

電源装置工材　　　　

FOR POWER UNIT

圧着端子

FV1.25-M4　ｱｶ

CRIMP-ON LUG

CODE NO.

000-536-715-00

電源装置工材　　　　

FOR POWER UNIT

ﾎｰﾙﾌﾟﾗｸﾞ

NO.4567

HOLE PLUG

CODE NO.

000-800-729-00

電源装置工材　　　　

FOR POWER UNIT

ｱｰｽ板

WEA-1004-0

COPPER STRAP

CODE NO.

500-310-040-00

型式/ｺｰﾄﾞ番号が２段の場合、下段より上段に代わる過渡期品であり、どちらかが入っています。　なお、品質は変わりません。

TWO TYPES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER PRODUCT MAY BE SHIPPED IN PLACE OF THE UPPER PRODUCT.

QUALITY IS THE SAME.

（略図の寸法は、参考値です。　DIMENSIONS IN DRAWING FOR REFERENCE ONLY.）

10CJ-X-9402

ＦＵＲＵＮＯ　ＥＬＥＣＴＲＩＣ　ＣＯ　．，ＬＴＤ.

Download from Www.Somanuals.com. All Manuals Search And Download.

A-22

Download from Www.Somanuals.com. All Manuals Search And Download.

A-23

Download from Www.Somanuals.com. All Manuals Search And Download.

A-24

Download from Www.Somanuals.com. All Manuals Search And Download.

A-25

Download from Www.Somanuals.com. All Manuals Search And Download.

A-26

Download from Www.Somanuals.com. All Manuals Search And Download.

A-27

Download from Www.Somanuals.com. All Manuals Search And Download.

A-28

Download from Www.Somanuals.com. All Manuals Search And Download.

A-29

Download from Www.Somanuals.com. All Manuals Search And Download.

D-2

Download from Www.Somanuals.com. All Manuals Search And Download.

D-3

Download from Www.Somanuals.com. All Manuals Search And Download.

D-4

Download from Www.Somanuals.com. All Manuals Search And Download.

D-5

Oct.31'03

Download from Www.Somanuals.com. All Manuals Search And Download.

D-6

Download from Www.Somanuals.com. All Manuals Search And Download.

D-7

Download from Www.Somanuals.com. All Manuals Search And Download.

D-8

Download from Www.Somanuals.com. All Manuals Search And Download.

D-9

Dec. 10, '02

Download from Www.Somanuals.com. All Manuals Search And Download.

D-10

Download from Www.Somanuals.com. All Manuals Search And Download.

D-11

Download from Www.Somanuals.com. All Manuals Search And Download.

D-12

Download from Www.Somanuals.com. All Manuals Search And Download.

D-13

Download from Www.Somanuals.com. All Manuals Search And Download.

D-14

Download from Www.Somanuals.com. All Manuals Search And Download.

D-15

Download from Www.Somanuals.com. All Manuals Search And Download.

D-16

Download from Www.Somanuals.com. All Manuals Search And Download.

S-1

電源装置

POWER UNIT

CSH-380

TB-E1

TB-B1

54-038-000

-601/SC

00-8016-038

-313-761HV

10S1259,MAX.20m,φ16.5

ｱｶ RED

10S1258,MAX.50m,φ18.6

外部ｲﾝﾀｰﾌｪｲｽ

INTERFACE UNIT

CN-A1

CN-B2

送振装置

ｸﾛ BLK

ｼﾛ WHT

ﾁｬ BRN

ｸﾛ BLK

ｱｶ

ﾁｬ

ｸﾛ

ｼﾛ

RED

BRN

他端に同じ

SAME AS THE

OTHER SIDE

TRANSMITTER

UNIT

CSH-310/310K/

310FⅡ

CS-120A

J201

00-8016-038

-313-761HV

10S1258,MAX.20m

00-8016-038

-313-761HV

110/220VAC: 設定変更

CHANGE TRANS. SETTING

BLK

WHT

CN-A5

他端に同じ

SAME AS THE

OTHER SIDE

CN-A1に同じ

SAME AS

CN-A1

ﾀﾞｲ ORG

ﾁｬ

ｱｶ

BRN

RED

54-038-000

-601/SC

54-038-000

-601/SC

CS-120C

ﾀﾞｲ ORG

CN-B3

10S1258,MAX.20m,φ18.6

CN-C2

WEA1004

W=50,1.2m

00-8016-038

-313-761HV

54-038-038

-313-761HV

ｱｶ

ﾁｬ

ｸﾛ

ｼﾛ

RED

BRN

BLK

WHT

ｸﾛ

ﾊｲ

ｷ

ﾁｬ

ｸﾛ

BLK

GRY

YEL

BRN

BLK

受信装置

RECEIVER UNIT

他端に同じ

SAME AS THE

OTHER SIDE

CN-A3

CN-A1/A2/A3

10S1258,MAX.30m

ｱｶ

ﾁｬ

ｸﾛ

ｼﾛ

RED

BRN

BLK

WHT

他端に同じ

SAME AS THE

OTHER SIDE

CSH-220A/

220K/220FⅡ

副指示器

SUB DISPLAY

CSH-236

ﾀﾞｲ ORG

ﾁｬ

ｱｶ

00-8016-020

-313-703V

BRN

RED

ﾑﾗｻｷ PPL

ﾀﾞｲ ORG

ｸﾛ

ｱｶ

ｷ

ｸﾛ

ﾁｬ

ｸﾛ

CN-C3

ﾀﾞｲ ORG

CN-C2に同じ

SAME AS

CN-C2

指示装置

DISPLAY UNIT

CSH-230/230F

ﾀﾞｲ ORG

BLK

RED

YEL

BLK

BRN

BLK

ﾁｬ

ｱｶ

BRN

RED

ｸﾛ

ﾊｲ

ｷ

ﾁｬ

ｸﾛ

BLK

GRY

YEL

BRN

BLK

54-038-000

-601/SC

上下制御箱

RAISE/LOWER

CONTROL BOX

ﾀﾞｲ ORG

CN-B4

ｼﾛ

ｱｶ

ｼﾛ

ｱｵ

WHT

RED

WHT

BLU

ｸﾛ

ﾊｲ

ｷ

ﾁｬ

ｸﾛ

BLK

GRY

YEL

BRN

BLK

54-038-000

-601/SC

TB-D1

CN-C4

10S1261,φ20

ﾁｬ BRN

ﾑﾗｻｷ PPL

ﾀﾞｲ ORG

ｸﾛ

ｱｶ

ｷ

ｸﾛ

ﾁｬ

ｸﾛ

ｸﾛ BLK

ｱｶ RED

ﾀﾞｲ ORG

ｸﾛ BLK

ﾑﾗｻｷ PPL

ﾐﾄﾞﾘ GRN

ﾑﾗｻｷ PPL

RED

ﾐﾄﾞﾘ GRN

ｸﾛ BLK

BLK

RED

YEL

BLK

BRN

BLK

ﾑﾗｻｷ PPL

ﾀﾞｲ ORG

ｱｶ

ﾄﾞｳｼﾞｸ COAX.

ﾐﾄﾞﾘ GRN

ｸﾛ

ｱｶ

ｷ

ｸﾛ

ﾁｬ

ｸﾛ

BLK

RED

YEL

BLK

BRN

BLK

ｼﾛ

ｷ

ｸﾛ

ｱｵ

WHT

YEL

BLK

BLU

ﾁｬ

ｸﾛ

ｱｵ

ﾁｬ

ｼﾛ

BRN

BLK

BLU

BRN

WHT

CN-A13

H10P-SHF-AA

リモート箱

REMOTE BOX

CSH-116

ｷ

YEL

ﾐﾄﾞﾘ GRN

ｸﾛ BLK

ｱｵ BLU

ｸﾛ BLK

ﾐﾄﾞﾘ GRN

ｸﾛ BLK

ﾑﾗｻｷ PPL

CN-A4

ｸﾛ

ｱｵ

ｼﾛ

ｷ

BLK

BLU

WHT

YEL

ﾐﾄﾞﾘ GRN

ｸﾛ BLK

ﾄﾞｳｼﾞｸ COAX.

ﾐﾄﾞﾘ GRN

ﾑﾗｻｷ PPL

10S1258,MAX.30m

ﾁｬ

ｸﾛ

ｱｵ

ﾁｬ

ｼﾛ

BRN

BLK

BLU

BRN

WHT

ﾁｬ

ﾊｲ

BRN

GRY

ｸﾛ BLK

ｼﾛ WHT

ｸﾛ BLK

ﾊｲ GRY

ﾄﾞｳｼﾞｸ COAX.

ﾐﾄﾞﾘ GRN

ｸﾛ

ｷ

BLK

YEL

ﾑﾗｻｷ PPL

ﾁｬ

ｱｵ

ﾁｬ

BRN

BLU

BRN

ｷ

YEL

ﾁｬ BRN

YEL

リモートディスプレイ

REMOTE DISPLAY

CSH-106

ｸﾛ

ｱｶ

ｷ

ﾊｲ

ｱｵ

ﾊｲ

ｱｶ

ﾊｲ

BLK

RED

YEL

GRY

BLU

GRY

RED

GRY

ﾑﾗｻｷ PPL

ﾁｬ BRN

ｷ

ﾑﾗｻｷ PPL

ｸﾛ BLK

ﾁｬ BRN

ｸﾛ BLK

CN-A7

CN-A8

CN-A9

(CN-A4/A7/A10)

(CN-A5/A8/A11)

(CN-A6/A9/A12)

ﾁｬ

ﾊｲ

BRN

GRY

CN-A1/A2/A3

C101

ECX-3C2V-T,MAX.30m,

(14S4382),φ13.7

P1～P4

C102

P1～P4

他端に同じ

SAME AS THE

OTHER SIDE

送受波器

TRANSDUCER

ﾄﾞｳｼﾞｸ COAX.

CN-A13

H10P-SHF-AA

リモート箱

REMOTE BOX

CSH-116

54-038-000

-601/SC

ﾐﾄﾞﾘ GRN

ﾊｲ GRY

(CN-A4/A7/A10)

(CN-A5/A8/A11)

(CN-A6/A9/A12)

CN-C5

CN-A7/A8/A9

または要改造

OR MODIFY

10S1260,MAX.20m

ECX-3C2V-T,MAX.30m,

φ13.7

C116

#16

P1～P4

DPYCY-1.5

WEA1004

W=50,1.2m

上下装置

HULL UNIT

CSH-21080/21120/21160

NCS-253P CN-A15

DPYCY-1.5

100VAC

1φ,50/60Hz

NCS-252P CN-A15

100VAC

1φ,50/60Hz

WEA1004

W=50,1.2m

DPYC-1.5

変圧器

TRANSFORMER

PT-400

110/220VAC

1φ,50/60Hz

アース銅板

COPPER STRAP

W=50 *1

アース銅板

COPPER STRAP

W=50 *1

NOTE

注記

*1: SHIPYARD SUPPLY.

*2: OPTION.

＊１）造船所手配。

DRAWN

TITLE

T.YAMASAKI

T.TAKENO

Jun. 26 '06

CHECKED

CSH-23/23F/23K

＊２）オプション。

名称

*3: GROUND THRU CABLE CLAMP.

＊３）ケーブルクランプで接地。

Jun. 26 '06

カラースキャニングソナー

相互結線図

*4: NUMERAL IN □ SHOWS POSITION OF CONNECTOR GUIDE PIN[B].

GUIDE PIN[S] IS SET ALWAYS TO POSITION “1”.

＊４）□内の数値は誤挿入防止ピンA（太）位置を示す。

ガイドピンB（細）は全て“1”に設定。

APPROVED

Jul. 24 '06 T.Matsuguchi

SCALE

MASS

NAME

*5: DO NOT CONNECT RGB LINE (CONNECTOR FF/HH, MM/NN, SS/TT) OF

CABLE 10S1258. OR INTERFERENCE MAY APPEARS ON THE DISPLAY.

＊５）10S1258のRGBライン(FF/HH,MM/NN,SS/TT)は接続しないこと。

画面の映像が歪む原因となることがあります。

COLOR SCANNING SONAR

INTERCONNECTION DIAGRAM

DWG.No.

C1304-C02- A

Download from Www.Somanuals.com. All Manuals Search And Download.

S-2

Download from Www.Somanuals.com. All Manuals Search And Download.

S-3

送振装置

TRANSMITTER UNIT

CSH-23/23K/23F/53/58/83

送受信装置

操作制御部

PROCESSOR UNIT

CSH-235/235F/235K/

835/585/535/735

3COX-2P-6C 5/10mまたは同等品

RGB 10P6949

or equivalent

CN-A16 D-sub

D-sub

TRANSCEIVER UNIT

CSH-73

古野製モニター MU-151C

FURUNO MONITOR

または OR

54-038-525-601/SC

択一

Selection

CN-B2

RED

BRN

BLK

WHT

ORG

BRN

RED

ORG

BLK

GRY

YEL

BRN

BLK

PPL

ORG

BLK

RED

YEL

BLK

BRN

BLK

GRN

BLK

アカ

チャ

クロ

シロ

ダイ

チャ

アカ

ダイ

クロ

ハイ

キ

チャ

クロ

ムラ

ダイ

クロ

アカ

キ

CN-A15

GND

NCS-253P

DPYCY-1.5

市販モニター(CRT/LCD)

Commercially available monitor

D-sub

100VAC

1φ,50-60Hz

75Ω同軸ケーブル

Coaxial cable, MAX. 30m

CN-A17 BNC

トランス

TRANSFORMER

PT-400

110/220VAC

1φ50-60Hz

CONE 10P6711

J21

D-sub

9pin

00-8016-038-313-761HV

CN-A5

RED

BRN

BLK

WHT

ORG

BRN

RED

ORG

BLK

GRY

YEL

BRN

BLK

PPL

ORG

BLK

RED

YEL

BLK

BRN

BLK

GRN

BLK

アカ

チャ

クロ

シロ

ダイ

チャ

アカ

ダイ

クロ

ハイ

キ

チャ

クロ

ムラ

ダイ

クロ

アカ

キ

00-8016-038

-313-761HV

J201 1

1 CN-A1

外部インターフェイス

INTERFACE UNIT

CS-120A

10S1258 or

S10-17-20(38P),φ18.6

20m MAX.

10S1258 or

S10-10-20(38P),φ18.6

SAME AS

CN-A5

SAME AS

CN-B2

20m MAX.: CSH-58

50m MAX.: CSH-23/23F/23K/73/83

80m MAX.: CSH-53

クロ

チャ

クロ

ミド

クロ

SHIELD ｼｰﾙﾄﾞ

同軸芯線

副指示器

SUB DISPLAY UNIT

CO-AX

GRN

BRN

BLK

BLU

BRN

WHT

PPL

BRN

GRY

ミド

チャ

クロ

アオ

チャ

シロ

ムラ

チャ

ハイ

CSH-236/236F/536/586

00-8016-038-313-761HV

CN-A1/A2/A3

H10P-SHF-AA

10S1627

RED

BRN

BLK

WHT

ORG

BRN

RED

ORG

BLK

GRY

YEL

BRN

BLK

PPL

ORG

BLK

RED

YEL

BLK

BRN

BLK

GRN

BLK

アカ

チャ

クロ

シロ

ダイ

チャ

アカ

ダイ

クロ

ハイ

キ

チャ

クロ

ムラ

ダイ

クロ

アカ

キ

CN-A13

リモート箱

REMOTE

CONTROL BOX

CSH-135/116

クロ

チャ

クロ

ミド

クロ

SHIELD ｼｰﾙﾄﾞ

同軸芯線

CO-AX

GRN

BRN

BLK

BLU

BRN

WHT

PPL

BRN

GRY

ミド

チャ

クロ

アオ

チャ

シロ

ムラ

チャ

ハイ

クロ

チャ

クロ

ミド

クロ

注記

*1. 造船所手配。

*2. オプション。

*3. 圧着端子、コネクタは取付済み。

*4. □内の数値は誤挿入防止ガイドピンA（太）の位置を示す。

ガイドピンB（細）はすべて”1”に設定。

*5. 10S1258のRGBライン（FF/HH,MM/NN,SS/TT）は接続しないこと。

画像の映像が歪む原因となることがあり。

*6. ケーブルクランプで接地。

*7. 同軸ケーブルを使用するときは内部でBNCコネクタを付けかえる。

SHIELD ｼｰﾙﾄﾞ

CO-AX

GRN

BRN

BLU

BRN

PPL

BRN

同軸芯線

ミド

チャ

アオ

チャ

ムラ

チャ

CN-A3 3

10S1258,φ18.6

30m MAX.

SAME AS

CSH-236/236F/536/536F

(CN-A7) R

(CN-A8) G

(CN-A9) B

R (CN-A4/7/10)

G (CN-A5/8/11)

B (CN-A6/9/12)

ECX3C-2V-T,φ13.7

(14S4382)30m MAX.

NOTES

*1. SHIPYARD SUPPLY.

*2. OPTION.

*3. CONNECTOR/LAG FITTED AT FACTORY.

*4. □ SHOWS POSITION OF CONNECTOR GUIDE PIN(LARGE).

GUIDE PIN(SMALL) IS SET ALWAYS TO POSITION '1'.

*5. DO NOT CONNECT RGB LINE (FF/HH,MM/NN,SS/TT) ON 10S1258, OR

INTERFERENCE MAY OCCUR ON DISPLAY.

*6. GROUNDED THRU CABLE CLAMP.

*7. WHEN COAXIAL CABLES ARE USED, REPLACE THE BNC CONNECTORS.

DRAWN

TITLE

NAME

CSH-235/235F/235K/835/585/535/735

カラースキャニングソナー操作制御部

相互結線図

E. MIYOSHI

Feb.15,'05

CHECKED

TAKAHASHI. T

IV-8.0SQ.

PE 保護アース

APPROVED

SCALE

Y. Hatai

MASS

REMARK

COLOR SCANNING SONAR PROCESSOR UNIT

INTERCONNECTION DIAGRAM

DWG No.

C1304-C01- B

FURUNO ELECTRIC CO., LTD.

Download from Www.Somanuals.com. All Manuals Search And Download.

S-4

Download from Www.Somanuals.com. All Manuals Search And Download.

Earthquake Sound Speaker EQ88 User Manual
Echo Paint Sprayer MS 41BP User Manual
Euro Pro Microwave Oven K5345B User Manual
EverFocus Camcorder 520TVL 380TVL User Manual
Exmark Lawn Mower LZ27KC604 User Manual
Extron electronic Stereo Receiver HDMI 201 Tx Rx User Manual
GE Air Conditioner AET05 User Manual
Generac Portable Generator 004373 1 004626 0 User Manual
GE Outboard Motor LM10 User Manual
Gigabyte Computer Hardware GA 945PLM DS2 User Manual