FRS1000 RADAR/PLOTTER/SOUNDER
QUICK OPERATION GUIDE
(USING THE REMOTE CONTROL)
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING FFAMILIAR WWITH THE DISPLAY
FRS-1000
1
2
3
4
5
6
Numeric
Keys
7
8
9
Selects a
display mode
0
Open/close
respective
menu
MODE
MENU/ESC
Adjusts
display
Omnipad -
Shifts cursor,
VRM, EBL
and selects
items on
RDR
PLTR SNDR
RDR
PLTR SNDR
BRILL
brilliance
MOB
+/-
CLR
ENT
POWER
menus
Turns power on/off
Marks man over
board position and
event positions
Enters plus, minus
and switches
co-ordinate
Silences buzzer;
temporarily erases
heading line, north
marker; erases
Confirms operation
marks, waypoints
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING FAMILIAR WITH THE REMOTE
RADAR BUTTON
Used to toggle between
stand-by and transmit.
PLOTTER BUTTONS
MOB - Press once to store
an event. Later you can
GOTO these events,
RADAR & PLOTTER
BUTTON
Used to zoom in and out
of range scales.
FRS-1000
ST-BY
TX
ZOOM
OUT
IN
which will be sorted from
newest to oldest. Hold
MOB for 5 seconds to
enable MOB mode. (See
page 3-8 in op. manual.)
PLTR
MOB
COMN
2
3
6
1
MARK - used to set a
mark on the chart using
either ship position or
cursor position. (See page
3-6 in op. manual.)
MARK
NUMERIC KEYPAD
Used to enter numbers
and select menus for all
modes.
5
8
0
4
7
GOTO - used to go to
cursor position, event,
waypoint or route. (See
page 3-12 in op. manual.)
GOTO
WPT
9
ENTER & ESCAPE
[ENT] - used as an
WPT - used to open way-
point menu. (See page 3-9
in op. manual.)
ENTER key in all modes
to confirm information
being selected or entered.
+/-
CLR
ENT
M
[ESC] - used as an
ESCAPE key in all modes
to exit from menu screen
to originally selected mode
display.
CURSOR CONTROLS
Arrow keys used to move
the cursor up, down, left
and right.
M
+
ESC
MODE KEYS
MODE
DISP
DISPLAY BUTTON
Used to change display
orientation to Heads up,
North up, Course up, or
True Motion for Radar and
Plotter.
MODE keys are used to
toggle on & off the radar,
plotter and sounder displays.
Hu/Nu/Cu/TM
SNDR
PLTR
RDR
RDR
ARP
A
MENU
MENU KEYS
ACQ
MENU keys are used to
toggle on & off the radar,
plotter and sounder menus.
PLTR
SNDR
RDR
RADAR BUTTON
Used to acquire ARPA
targets.
SNDR
M
M
M
M
SOUNDER GAIN
RADAR SEA CLUTTER
STC - used to suppress
sea clutter.
GAIN - used to adjust the
gain. 50/200 may be
independently adjusted.
STC
RANGE
GAIN
GAIN
M
M
M
M
SOUNDER RANGE
RANGE - used to adjust
the sounder’s range.
RADAR GAIN
GAIN - used to adjust the
Radar’s gain.
Download from Www.Somanuals.com. All Manuals Search And Download.
RADAR OPERATION
Toggles between
stand-by and
transmit.
FRS-1000
ST-BY
TX
ZOOM
OUT
IN
SELECTING THE RRADAR DISPLAY
PLTR
MOB
COMN
2
1. Press the [RDR] MODE key to turn Radar on
2. Press the [RDR] MODE key again if you want
to turn the Radar display off.
Decreases the Radar
range scale.
3
6
1
MARK
Increases the Radar
range scale.
5
8
0
4
7
TRANSMITTING
GOTO
WPT
9
1. Press the [ST-BY/TX] key to transmit
2. Press the [ST-BY/TX} key again if you want to
return to stand-by mode.
+/-
CLR
Moves the
Radar cursor.
ENT
M
M
+
ESC
ADJUSTING GAIN
Toggles the Radar
display on and off.
MODE
DISP
1. Press or hold down the Radar GAIN [L] key to
increase gain or the Radar GAIN [M] key to
decrease gain
2. Observe the gain level indicator in the upper
right corner of the display along with the Radar
presentation to optimize your Radar’s gain
setting. Adjust for maximum targets with slight
background noise or “speckle”.
Hu/Nu/Cu/TM
SNDR
PLTR
RDR
RDR
ARPA
Increases or
decreases the
Radar’s Gain.
MENU
ACQ
PLTR
SNDR
RDR
SNDR
M
M
M
M
STC
RANGE
GAIN
GAIN
Increases or
decreases the
Radar’s Sea Clutter.
M
M
M
M
SELECTING A RANGE SCALE
1. Press the ZOOM [IN] key to decrease the
Radar range scale and the ZOOM [OUT] key to
increase the Radar range scale
Range scale indicator
Level Indicator Bars
2. You can see the currently selected range scale
by checking the indicator in the upper left cor-
ner of the display.
SUPPRESSING SEA CLUTTER
1. Press the Radar STC [L] key to increase sea
clutter suppression and the Radar GAIN [M]
key to decrease sea clutter
2. You can see the amount you are increasing and
decreasing on the A/C SEA Level Indicator Bar
in the upper right corner of the display. The A/C
Sea Level indicator bar shows the amount of
A/C Clutter suppression being used.
For a complete and detailed description of all the Radar
functions, please refer to the FRS1000 Operations Guide.
Download from Www.Somanuals.com. All Manuals Search And Download.
Increases and
decreases the chart
range scale.
PLOTTER OPERATION
FRS-1000
Creates Man Over
Board Mark.
ST-BY
TX
ZOOM
OUT
IN
SELECTING THE PLOTTER DISPLAY
PLTR
MOB
Activates mark menu
allowing you to
assign a mark.
COMN
2
1. Press the [PLTR] MODE key to turn the
Plotter on
3
6
1
Activates goto menu
allowing you set a
course.
2. Press the [PLTR] MODE key again if you want
to turn the Plotter display off.
MARK
5
8
0
4
7
Activates waypoint
menu allowing you to
create a waypoint.
GOTO
WPT
SELECTING TTHE RANGE
9
1. Press the ZOOM [IN] key to decrease the
Plotter range scale and the ZOOM [OUT] key
to increase the Plotter range scale.
Confirms entry.
+/-
CLR
ENT
Moves Plotter
cursor in direction
arrow is indicating.
M
M
+
MAN OVER BOARD
ESC
Escapes the Plotter
menu and brings
you back to the
display mode.
MODE
DISP
1. Press and hold the [MOB] key until confirmation
appears to enable the MOB mode. The MOB
position will appear as a large “M” waypoint.
Hu/Nu/Cu/TM
SNDR
PLTR
RDR
RDR
ARPA
MENU
ACQ
PLTR
SNDR
RDR
Toggles the Plotter
display on and off.
STORE AN EVENT
SNDR
M
M
M
M
1. Press the [MOB] key momentarily to save the
current ship position as an event. These events
are saved to memory and can be returned to
via the GOTO L/L position method.
STC
RANGE
GAIN
GAIN
M
M
M
M
ENTERING MARKS
1. Use the cursor [LM] keys to move to your
desired mark coordinates
2. Press the [MARK] key to place a mark at the
cursor position. To place a mark at current ships
position, turn off the cursor by pressing the +/-
key. (See page 3-7 in op. manual to change
mark color and shape.)
REGISTERING WAYPOINTS
SETTING/CANCELING DESTINATION
1. Press the [WPT] key to access the waypoint
menu
2. When menu appears, you may enter waypoints
by using the cursor, saved event, own ships
position or via direct entry on the waypoint list.
(See page 3-9 in the op. manual)
1. Press the [GOTO] key to set your destination
waypoint by cursor, event, L/L position,
waypoint number or route number
2. Current destination waypoint may also be
cancelled in this menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
SOUNDER OOPERATION
FRS-1000
ST-BY
TX
ZOOM
OUT
IN
SELECTING THE SOUNDER DISPLAY
PLTR
MOB
COMN
2
1. Press the [SNDR] MODE key to turn Sounder on
2. Press the [SNDR] MODE key again if you want
to turn the Sounder display off.
3
6
1
MARK
5
8
0
4
7
GOTO
WPT
9
CHANGING SOUNDING RANGE
1. Press the Sounder RANGE [L] key to increase
range or the Sounder RANGE [M] key to
decrease range.
+/-
CLR
ENT
M
M
+
ESC
Toggles the Sounder
display on or off.
MODE
DISP
ADJUSTING GAIN
Hu/Nu/Cu/TM
SNDR
PLTR
RDR
RDR
ARPA
Increases or
decreases the
Sounder’s Gain.
MENU
1. Press or hold down the Sounder GAIN [L] key
to increase gain or the Sounder GAIN [M] key
to decrease gain. Move the cursor control up
or down to select either the 200 kHz gain
adjustment or the 50 kHz gain adjustment.
ACQ
PLTR
SNDR
RDR
SNDR
M
M
M
M
STC
RANGE
GAIN
GAIN
Increases or
decreases the
Sounder’s Range.
M
M
M
M
Water Temperature
Depth
For a complete and detailed description of all the Radar
functions, please refer to the FRS1000 Operations Guide.
Download from Www.Somanuals.com. All Manuals Search And Download.
Furuno USA, Inc. • 4400 NW Pacific Rim Blvd. • Camas, WA 98607-9408
Download from Www.Somanuals.com. All Manuals Search And Download.
|