C150-E022-05EN
M3093EX AND M3093GX
IMAGE SCANNER
OPERATOR’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventions
Special information, such as warnings, cautions are indicated as
follows:
WARNING
A WARNING indicates that personal injury may result if you do not
follow a procedure correctly.
CAUTION
A CAUTION indicates that damage to the scanner may result if you
do not follow a procedure correctly.
NOTICE
A NOTICE provides "how-to" tips or suggestions to help you perform
a procedure correctly. NOTEs are particularly useful for first-time
users.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
CHAPTER 1 PREFACE .................................................................................................... 1-1
CHAPTER 2 COMPONENTS ........................................................................................... 2-1
2.1 Checking the Components ......................................................................................... 2-1
2.2 Part Names and Functions........................................................................................... 2-2
2.2.1 Exterior view of image scanner .......................................................................... 2-2
2.2.2 Functions of each part ......................................................................................... 2-3
2.3 Indicator Functions ..................................................................................................... 2-4
2.3.1 Indicators ............................................................................................................ 2-4
3.1 Precautions .................................................................................................................. 3-1
3.3 Connections................................................................................................................. 3-3
3.4 Mounting the Stacker .................................................................................................. 3-5
3.5 SCSI-ID Setting .......................................................................................................... 3-6
CHAPTER 4 OPERATIONS ............................................................................................. 4-1
4.1 Turning on the Power .................................................................................................. 4-1
4.2 Reading a Document in Flatbed Mode........................................................................ 4-2
4.2.1 Reading a standard-size document ..................................................................... 4-2
4.2.2 Reading a page from a thick book ...................................................................... 4-3
4.2.3 Reading a document larger than the document board......................................... 4-4
4.3 Reading Documents in ADF Mode............................................................................. 4-5
CHAPTER 5 MAINTENANCE ......................................................................................... 5-1
5.1 Removing Jammed Documents .................................................................................. 5-1
5.2 Notes on Daily Use ..................................................................................................... 5-2
5.3 Cleaning ...................................................................................................................... 5-2
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3.1 Cleaning the document cover, document holding pad, and document bed ........ 5-2
5.4.1 Parts number and replacement cycle................................................................... 5-4
5.4.3 Replacing pick roller........................................................................................... 5-5
CHAPTER 6 TROUBLESHOOTING .............................................................................. 6-1
APPENDIX A ..........................................................................................................................A-1
A.1 Installation Specifications ...........................................................................................A-1
A.2 External Dimensions ...................................................................................................A-2
APPENDIX B .......................................................................................................................... B-1
B.1 Test mode for maintenance ......................................................................................... B-1
APPENDIX C .......................................................................................................................... C-1
C.1 Option.......................................................................................................................... C-1
C.2 IPC-2/CMP-2 option board installation ...................................................................... C-1
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
page
2.1 Received components ................................................................................................. 2-1
2.2 M3093EX/GX parts names ......................................................................................... 2-2
2.3 M3093EX/GX Indicators ............................................................................................ 2-4
3.1 SCSI-ID setting ........................................................................................................... 3-6
4.1 Flatbed reading ............................................................................................................ 4-3
4.2 Removing the document cover.................................................................................... 4-4
4.3 ADF paper chute setting.............................................................................................. 4-7
4.4 Loading the document................................................................................................. 4-9
5.1 Removing jammed documents .................................................................................... 5-1
5.2 Cleaning the document cover, document holding pad, and document bed................. 5-2
5.3 Cleaning the ADF ...................................................................................................... 5-3
5.4 Pick Roller replacement .............................................................................................. 5-5
5.5 Move the Retaining spring .......................................................................................... 5-6
5.6 Slide the Pick Roller ................................................................................................... 5-6
A.1 External dimensions ....................................................................................................A-2
v
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLES
page
1.1 The differences between the M3093EX and the M3093GX....................................... 1-1
3.1 SCSI-ID setting ........................................................................................................... 3-6
6.1 Check items ................................................................................................................. 6-1
A.1 Installation specifications ............................................................................................A-1
B.1 LED at an error............................................................................................................ B-2
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1 PREFACE
This manual describes how to operate the M3093EX and M3093GX image scanners. An image
scanner optically reads image information from a document and outputs the information to the
host system. The differences between the M3093EX and the M3093GX image scanners are
listed in table 1.1.
Table 1.1 The differences between the M3093EX and the M3093GX
Model number
M3093EX
Interface
Shipping
models
Image size
Automatic
document feeder
RS232C
North America
Europe
A4 size or letter Yes
size Max. 50 pages
(A4)
+
VIDEO
M3093GX
SCSI2
North America
Europe
This manual should be read before operating the image scanner to ensure correct operation.
Note on Copyright Act
This document cannot be reproduced or copied for any use other than private without the
author’s permission.
1 – 1
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is intentionally left blank.
1 – 2
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2 COMPONENTS
2.1 Checking the Components
2.2 Part Names and Functions
2.3 Indicator Panel Functions
After unpacking image scanner, confirm that all the components have been received. This
section describes the components of the image scanner and their functions.
2.1 Checking the Components
These high precision components must be handled with care. Confirm
that all the components shown in figure 2.1 have been received. If
any component is missing, please contact your local Fujitsu sales
person.
Power cable
for Europe
Image scanner
Power cable for
North America
Terminator
(for M3093GX)
Operator’s Guide
(this manual)
Pads
Inspection
report
One stacker
Figure 2.1 Received components
2 – 1
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Part Names and Functions
This section shows the exterior view of image scanner. This section
also provides names of each part and describes their functions.
2.2.1 Exterior view of image scanner
The image scanner can read a document of A4 or letter size at maxi-
mum.
Document
holding pad
Document cover
Document bed
Automatic document
feeder (ADF)
Indicators
Stacker
ADF lever
ADF paper chute
Third party slot opening
(M3093EX)
Power switch
Interface connectors
Power inlet
Figure 2.2 M3093EX/GX parts names
2 – 2
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2.2 Functions of each part
Document cover:
Closed over and holds a document to be
read.
Document bed:
A document to be read is placed on the
bed also called Flatbed (FB).
Document holding pad:
Presses a document to the document bed.
Automatic document feeder (ADF):
Automatically feeds documents to the
reading position.
Stacker:
Stacks the read documents.
Turns the power on or off.
Power switch:
Indicators:
These LEDs indicate the status of the
scanner.
ADF paper chute:
ADF lever:
Holds the documents to be fed by the
automatic document feeder.
Opens or closes the automatic document
feeder to remove documents jammed in
the feeder.
Power inlet:
To be connected to an AC power outlet
with the power cable.
Interface connectors:
Third party slot opening:
To be connected to the host system with
interface cables.
Reserved (M3093EX)
2 – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Indicator Functions
Power
Read
Check
Figure 2.3 M3093EX/GX Indicators
2.3.1 Indicators
The meaning of each indicator is as follows:
Power indicator (Green):
Lights to indicate the power is on.
Read (reading in progress) indicator (Green):
Lights to indicate reading is in progress.
Check (device check) indicator (Yellow):
Lights if a device error occurs which may result in a service
call. This indicator blinks if a document is jammed in the
automatic document feeder. This indicator turns off when the
jammed documents are removed from the feeder and the feeder
is closed.
This indicator blinks in four seconds period if the ADF cleaning
is necessary. (See section 5.3.2)
2 – 4
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 3 INSTALLATION AND CONNECTIONS
3.1 Precautions
3.2 Removing the Carrier Fixing Bracket
3.3 Connections
3.4 Mounting the Stacker
3.5 SCSI-ID Setting
This chapter explains how to install and connect the image scanner.
3.1 Precautions
Do not install the image scanner in the following places and environ-
ments. See the appendix A.1 “Installation Specifications” for the
information such as size of installation space.
Place the scanner away from electrical noise
sources and strong magnetic fields. If the
image scanner is used near an air conditioner,
copying machine, or TV set, the scanner may
operate incorrectly.
Do not install the scanner in a humid, dusty,
or damp places. These enviroments may
shorten scaner life or cause hardware fail-
ures. Do not place the image scanner where
liquid spills may occur. Place it on a flat and
even surface.
Keep the scanner out of the sun and away
from heaters. These environments may
shorten scanner life or cause hardware
failures.
Do not install the scanner in a place where
vibrations may occur. This environment may
cause hardware failures or may cause the
scanner to operate incorrectly.
CAUTION
Place the image scanner on a level surface.
Place the image scanner so that the rubber
pads are secured on a flat and solid desktop.
Be aware of static electricity. If static
electricity is generated, the scanner may
operate incorrectly. Be sure that the flooring
and the desk are made of materials that do
not generate static electricity.
3 – 1
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Removing the Carrier Fixing Bracket
To keep the scanner from being damaged during shipping, the carrier
unit is fixed with a bracket. After placing the carrier unit at the
installation place, remove this bracket as explained below.
1
Place the image scanner on the edge of the desk top so that the left side (where ADF
is placed) of the scanner extends from the desk top. Do not set the image scanner
upside down or on its side.
×
×
2
Remove the carrier fixing bracket from position A . Then install the carrier fixing
bracket at position B .
Front side
Enlarged
CArier bracket
(Position for operation)
Bottom view
Carier bracket (Position for
storage, position for shipment)
Enlarged section A enlarged
B
ADF side
A
Carier bracket
(Position for shipment)
3 – 2
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Connections
Connect the image scanner using the following procedure.
1
Set the power switch to off.
Power switch
2
Connect the power cable.
Connect the power cable to the power inlet on the back of the image scanner.
Connect the other end of the power cable to a power outlet.
Power outlet
for North America
Power inlet
Power cable
for Europe
3
Connect the interface cables (for M3093EX).
Connect the interface cables to the interface connectors and fasten the cables
with catches and screws as shown below.
Connect the other end of each interface cable to the host computer.
Back of the image scanner
Catches
Interface cable for video
Interface cable for RS232C
Screws
To the host system
3 – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
(M3093GX)
Connect the interface cables to the interface connectors and fasten the cables
with the catches. Connect the other ends of the cables to the host system. If the
image scanner is at the terminal side, connect the terminator.
Back of the image scanner
Terminator
C
he image scanner is at
terminal side, connect
the terminator to the
connector to which an
interface cable is not
connected.
host
system
3 – 4
Download from Www.Somanuals.com. All Manuals Search And Download.
3.5 SCSI-ID Setting
Use the address switches to set the device address. After the setting
turn the power on.
Address switch
Interface connector
Interface cable
Figure 3.1 SCSI-ID setting
Table 3.1 SCSI-ID setting
ID
Contents
0 to 7
8, 9
Available
No Operation
* When the scanner is terminated device, the termination connector
must be connected on one side of the connectors.
3 – 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4 OPERATIONS
4.1 Turning on the Power
4.2 Reading a Document in Flatbed Mode
4.3 Reading Documents in ADF Mode
Documents can be read in the flatbed mode or automatic document feeder (ADF) mode. In the
flat-bed mode, each document is placed on the document bed and is read one by one. In ADF
mode, documents are fed and read automatically.
This section explains how to turn on the power and how to read documents.
NOTICE: If the “Check” indicator blinks in four seconds period, clean the ADF in accordance
with the section 5.3.
NOTICE: If the top 3 mm of the read area isn’t left blank (grounding color) by specifying a
drop-out color, read the document by selecting photo.
4.1 Turning on the Power
This section explains how to turn on the power.
Press “I” on the power switch. When the power is turned on, the
power indicator is lit.
Power switch
Press f the power.
Power OFF
Power ON
4 – 1
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Reading a Document in Flatbed Mode
This section explains how to read a document placed on the document
bed.
4.2.1 Reading a standard-size document
If the size of the document is smaller than the document bed, read the
document using the following procedure:
1
2
Open the document cover.
Place the document face down on the document board. Correct
any curled or folded parts of the document.
3
4
Position the long side (in landscape mode) or the short side (in
portrait mode) of the document to the left side of the document
bed.
Position the left top of the document to the reference mark. If the
document is not placed correctly, reading cannot be done cor-
rectly.
5
6
7
Close the document cover slowly. If the document cover is
closed too quickly, the document may move.
Read the document. Do not press on or open the document cover
during the read operation.
After reading, open the document cover to remove the document.
4 – 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Document cover
Reference mark
1
4
2
5
Document
Document bed
Figure 4.1 Flatbed reading
3
2
4.2.2 Reading a page from a thick book
To read a page from a thick book, remember the following points:
1
2
3
Do not close the document cover forcibly. Keep the cover open
for reading.
Any document parts that are not in contact with the glass will not
be read correctly.
Do not move the document during the read operation.
4 – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.3 Reading a document larger than the document board
If the size of the document is larger than the document board, read the
document using the following procedure:
1
Open the document cover at an angle of about 80°, then slide the
cover to the direction of the arrow to remove it.
2
3
4
5
Place the document face down on the document bed.
Place the document cover over the document.
Read the document.
After the read operation, remove the document, replace the
document cover. Mount the document cover to the original
position, and close the document cover.
Document cover
80°
Document bed
Figure 4.2 Removing the document cover
NOTICE: Do not remove the document cover for any other purpose.
4 – 4
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Reading Documents in ADF Mode
This section explains how to read documents using the automatic
document feeder. If the following steps are not closely followed, a
feed error may occur.
1
Check the documents as follows:
(a) Paper quality
• Wood-free paper.
• PPC paper; Specified by XEROX Corporation.
(b) Paper weight
• 13.91bs to 27.81bs
(c) Paper size
• Letter, Legal, A4, A5, B5
(d) Items to avoid
• The following documents may be hard to read by ADF. Before
you start the large quantity reading, check that the document is
read appropriately. If the reading is not appropriate, read them
by flatbet.
– Paper with a clip or staple.
– Paper that has ink which is not dry.
– Paper thickness is not constant, such as an envelope.
– Paper that has large rumples or curl. (See NOTICE)
– Paper that has folds or tears.
– Tracing paper.
– Coating paper.
– Carbon paper.
– Paper that is smaller than A5 size or larger than A4 width.
– Items other than paper, such as clothes, metal sheet, or OHP
film.
– Photographic paper.
– Paper that has perforations on its side.
– Paper that has a shape other than square.
– Paper that is very thin.
NOTICE: The important document which shall not be torn must be read by flatbet.
NOTICE: Carbonless papers have the chemical composition which damages the pad and
pickroller. Therefore, note the following remarks
Cleaning:
If the miss pick occurs frequently, clean the pad and pickroller
in accordance with the section 5.3.2.
Replacement of parts: The life of the pad and the pickroller may be shorter than the
case that PPC document is fed. Replacement cycle of the pad
and the pickroller may be 100,000 sheets or more if the paper
quality is good and cleaning is done well. Before you start the
large quantity reading, check the replacemtne cycle of them
and prepare pads and pickrollers.
4 – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE: Paper should be straightened to fit the condition below.
More than
More than
30 mm
30 mm
Feed direction
Read surface
Feed direction
Read surface
Less than
5 mm
Less than
5 mm
Top of the paper
Top of the paper
2
Switch the paper select lever.
Switch the lever in the following procedures:
• Open the automatic document feeder (ADF) while lifting up the
ADF lever.
• Set the paper select lever.
Plain paper: "NORMAL"
Heavy paper: "THICK"
• Reset the ADF. (Check that the ADF lever is set at the "NOR-
MAL" position.)
NOTICE: Always reset the paper select lever to "NORMAL" posi-
tion, when you feed the paper other than heavy paper.
ADF l
Automatic docume
feeder (ADF)
Paper select lever
(NORMAL mode)
ADF frame
(THICK mode)
Section A enlargerd
4 – 6
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Pull up the ADF paper chute as follows:
• Hold the document cover with one hand and pull up the ADF
paper chute with the other hand until it clicks.
ADF paper chute
Document cover
ADF paper chute
Push for storage
Shaft
Document cover
Figure 4.3 ADF paper chute setting
4
Fan the documents as follows:
• Take a 15 to 20 mm thickness of documents. Lightly hold both
ends with both hands. Bend the documents into an arch as
shown below.
• Then hold the documents tightly with both hands, and
straighten the documents. The center of documents swell and
air is introduced between the documents.
• Repeat this operation two or three times.
• Turn the documents 90°, and repeat the operation again.
15 to 20 mm
4 – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
5
6
Take documents to be placed in the ADF paper chute. The
thickness of the documents to be placed in the ADF paper chute is
limited depending on the size of the documents as follows:
A4 or letter size or smaller: 4 mm or less
Angling the documents
Angle the document edges as follows:
• Place the documents face down with the top to the left as shown
in A. The long side is the top for landscape mode and the short
side is the top for portrait mode.
• Lift the documents holding the both ends with both hands.
• Hold the documents tightly with your left hand and bend the
documents as shown in B.
• Grip tightly with your right hand, loosen the grip of your left
hand, and straighten the documents as shown in C.
• Repeat these operations until the top is angled 20° or less as
shown in D.
Top
A
(For portrait mode)
B
C
D
20° or less
4 – 8
Download from Www.Somanuals.com. All Manuals Search And Download.
7
8
9
Open the right and left guides of the ADF paper chute about 5
mm wider than the document width.
Place the documents face down onto the ADF paper chute with
the top edges facing the automatic feeder hole.
Adjust the guides to the document sides. Skewing may occur if
there is a gap between the guides and documents.
10 Slide the documents down until they touch the far end of the
automatic feeder opening. If the documents hit the far end hard,
two or more pages may be fed at once. Make sure that the upper
end of documents are not turned.
11 Read the document. If a wrong document size or mode (portrait
or landscape) is selected, the document may not be read entirely.
NOTICE: Unless 3 mm of the leading edge of forms are not
white or dropout color, set the document type to
"Photo."
12 After reading, remove the documents from the stacker.
Guide
Automatic document feeder
Documents
ADF paper chute
Guide lever (Both sides)
Guide
Figure 4.4 Loading the document
Portrait
Landscape
Automatic document feeder
ADF paper chute
Documents
4 – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is intentionally left blank.
4 – 10
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 5 MAINTENANCE
5.1 Removing Jammed Documents
5.2 Notes on Daily Use
5.3 Cleaning
5.4 Consumables/Periodical replacement parts
This section explains how to remove jammed documents, and provides notes on daily use and
cleaning.
5.1 Removing Jammed Documents
If documents jam while being fed by the ADF, remove the jammed
documents as follows:
1
2
3
4
Remove the documents from the ADF paper chute.
Pulling up the ADF lever, open the automatic document feeder.
Remove the jammed documents.
Close the ADF until the ADF lever locks.
ADF lever
Automatic document feeder (ADF)
Figure 5.1 Removing jammed documents
5 – 1
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Notes on Daily Use
Note the following points on daily use:
NOTICE
• Do not look directly at the light source during the read operation.
Keep the document cover in place.
NOTICE
• See Section 5.3 “Cleaning”, to clean the document cover, document
holding pad, document bed, and the automatic document feeder.
Especially, clean the automatic document feeder (ADF) periodically.
For the cleaning cycle, see Section 5.3.2, "Cleaning the ADF."
5.3 Cleaning
This section explains how to clean the image scanner.
5.3.1 Cleaning the document cover, document holding pad, and document bed
• Use a dry cloth or a cloth with a neutral cleanser to remove dirt from
the document cover, document holding pad, and document bed. Do
not use organic solvents such as a thinner.
• Make sure that no liquid enters the scanner from the edges of the
document bed glass.
er
Figure 5.2 Cleaning the document cover, document holding pad, and document bed
5 – 2
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3.2 Cleaning the ADF
Clean the automatic document feeder (ADF) once every 5,000 pages.
The cycle depends on the types of documents used (paper quality, a
level of toner fusing on paper).
1
2
Pull the ADF lever up to open the ADF.
Use the dry cloth or a cloth with ethyl alcohol to softly remove
dirt and dust as follows.
Pad:
Wipe the pad in a downward direction (indi-
cated by the arrow). Be careful not to hook
the pick spring when wiping.
Glass:
Wipe the glass lightly.
Pick roller :
Wipe the roller softly. Be careful not to
damage the surface of the roller.
Feed roller and coupled feed roller:
Wipe the rollers softly. Be careful not to
damage the surface of the rollers.
Ejection roller and coupled ejection roller:
Wipe the rollers softly. Be careful not to
damage the surface of the rollers.
Sheet guide (white part):
Wipe the sheet guide softly.
3
Close the ADF to lock the ADF lever.
Ejection roller (Clean the roller
on the opposite side also.)
Feed roller
Pick spring
A
Pad
Automatic docu
Coupled feed roller
Sheet guide (white part)
Glass
Figure 5.3 Cleaning the ADF
5 – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4 Consumables / Periodical replacement parts
5.4.1 Parts number and replacement cycle
Customer is responsible to change these items periodically.
No.
1
Part name
Pad ASY
Pick roller
Part number
PA02201-0020
Replacement cycle
Every 100,000 pages or annually(*1)
Every 200,000 pages or annually(*1)
2
PA02212-K001(*2)
*1: These replacement cycle may vary by the paper quality and cleaning result. When PPC
paper is used, replacement cycle may be 300,000 sheets or more by good cleaning. Before
you start the large quantity reading, evaluate the replacement cycle and prepare pads and
pickrollers.
*2: This part may not be provided in some countries due to the conformability of safety regula-
tion. Before the order of the pick roller, contact your sales agent or Fujitsu service repre-
sentative.
5.4.2 Replacing pad ASY
1
Lift up the ADF lever and open the ADF.
2
Insert a coin in the slot or hold the both sides of the pad ASY,
then slide it to the direction of the arrow to remove the pad.
Pad ASY
ADF lever
Slot
NOTICE: Set the paper select lever to “N”, before removing pad ASY. (See Section 4.3)
5 – 4
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Insert the pad assembly into the ADF frame hole (the bigger one),
slide the assembly to the direction of the arrow until it clicks.
ADF frame
Pad assy
NOTICE: Pad can be replaced by aligning the holes of the pad with the pins of the Pad holder.
Pad holder
Pad
Pick spring
5.4.3 Replacing pick roller
Thumb Screw
Replace the pickroller as follows.
Guide A
a. Pull the cap up to open the ADF
unit.
b. Remove two thumb screws
shown in Figure 5.4. And re-
move the Guide A.
Thumb Screw
Figure 5.4 Pick Roller replacement
5 – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
c. Pinch the retaining spring and
slide it toward the roller. Free
bearing A from the bracket by
sliding it toward the roller.
B
etaining Spring
Figure 5.5 Move the Retaining spring
d. Slide the pick roller shaft in the
direction of arrow B and remove
the shaft from bearing B.
The roller shaft can then be lifted
and removed as shown in Figure
5.6.
e. Remove the bearing B.
f. Mount the new pick roller in
reverse order of removal.
Bearing B
Figure 5.6 Slide the Pick Roller
NOTICE: When mounting the Guide A, note that the hooks of the retaining spring are not
pressed by the Guide A. (See figure bellow)
Guide A
j
×
Retaining spring
5 – 6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 6 TROUBLESHOOTING
If a problem occurs, use Table 6.1 to resolve the problem.
Table 6.1 Check items
Problem
Possible cause
Response
No power
The power switch was not
turned on.
Press the power switch.
The power cable was not
connected correctly.
Connect the power cable correctly.
——————————
Turn off the power once and make an
attempt to turn on the power again. If the
power is not turned on, contact your
Fujitsu service representative.*
Read operation
does not start.
The documents were not
placed on the ADF correctly.
Insert the first a few pages into the slot.
The ADF was not closed
completely.
Make sure that the ADF is closed com-
pletely.
The interface cables were not Connect the interface cables correctly.
connected correctly.
Terminator was not con-
nected. (M3096GX).
Connect the terminator.
Pictures and
photographs are selected.
not read cor-
Halftone processing was not
Select a halftone mode from the host
system.
The document bed, docu-
ment holding pad, or inside
ADF is dirty.
Clean the dirty parts as explained in
Section 5.3, “Cleaning.”
rectly.
Characters and
lines are not
Simple binarization was not
done.
Select a binarization mode from the host
computer.
read correctly.
The document bed, docu-
ment holding pad, or the
inside of the ADF is dirty.
Clean the dirty parts as explained in
Section 5.3, “Cleaning.”
Image is dis-
torted or un-
clear.
The document was moved
during the read operation.
Keep the document cover closed during
reading so that the document will not be
moved.
The document was not in
contact with the glass.
Adjust the document so that it is in
contact with the glass.
6 – 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6.1 Check items (continued)
Problem
Possible cause
Response
The check
indicator is on.
The carrier fixing bracket
was not removed.
Remove the carrier fixing bracket as
explained in Section 3.2, “Removing the
Carrier Fixing Bracket.”
——————————
Turn the power off then on again. If the
check indicator turns on again, contact the
sales person in charge or a Fujitsu service
representative.*
“Check” lamp
blinks at 4
The pick roller is dirty.
When the power is turned off, the mes-
sage is cleared.
seconds period.
Even if the message is displayed, the read
operation can be continued. Clean the
pick roller after the read operation.
(See Section 5.3.2.)
The unallowable document
was read in the automatic
document feeder.
If a document not meeting the scanner
specifications is read in the automatic
document feeder, the document is not fed
smoothly and an error message may be
displayed.
(See Section 4.3.)
Read the document in the flat bed station.
Paper double feed. Pad is dirty.
Pad is worn out.
Clean the Pad. (See Section 5.3.2)
Replace the Pad. (See Section 5.4.2)
Clean the Pick roller. (See Section 5.3.2)
Miss pick.
Pick roller is dirty.
Pick roller is worn out.
Replace the Pick roller.
(See Section 5.4.3)
Paper jam.
Some foreign particles are in Clean the ADF (See Section 5.3.2) or
ADF. remove any foreign particles.
* Please check the test mode in appendix B, if possible, before calling the service representa-
tive and inform status of the indicators.
6 – 2
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A
A.1 Installation Specifications
Table A.1 Installation specifications
Item
Specification
Depth
External dimensions (mm)
Width
530
Height
173
376
Weight (kg)
11
Input power
Voltage
100 to 120 VAC, 200 to 240 VAC
Number of phases
Frequency
Single-phase
50/60 Hz
100 VA
Power
Temperature and
humidity allowed
ranges
Operation
5 to 35°C
20 to 80%
Idle
Temperature
Humidity
–20 to 60°C
8 to 95%
A – 1
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B
B.1 Test mode for maintenance
CAUTION: Please follow the procedure here or the offset data may be changed incor-
rectly. If the scanner does not react as the procedure below, turn off the
scanner and start from the beginning.
(1) Activating a test mode
Open the ADF cover and set the sensors to the following state before turning on the image
scanner. The image scanner can be placed in the maintenance mode by pulling out the
empty sensor lever and setting the B5 size sensor lever to down position with the ADF
cover fully opened (see Figure below). If the image scanner is placed in the maintenance
mode, the POWER lamp blinks. If the POWER lamp does not blink, turn off the power
and try again. Then close the ADF.
(Setting of the ADF sensors for maintenance mode)
- Empty sensor: UP
- B5 size sensor: DOWN
B5 Size sensor
Empty sensor
DOWN
UP
ADF open
B – 1
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) Activating the continuous operation test
Open the ADF and close it again. If no document is loaded on the ADF within five sec-
onds after closing the ADF, the image scanner runs in flatbed mode. If documents are
loaded on the ADF within five seconds after closing the ADF, the image scanner continu-
ously feeds the document from ADF. Once the image scanner start reading documents in
the flatbed mode, it does not feed documents from ADF even if documents are loaded on
the ADF.
(3) Ending the test in flatbed mode
To stop the carrier movement in flatbed mode, open the ADF cover. If the ADF cover is
opened, the POWER lamp starts blinking immediately after the carrier returns to the home
position.
(4) Ending the test in ADF mode
If the ADF document hopper is empty, feeding documents from the ADF ends. To restart
feeding, open the ADF cover and close it again. Then load documents on the ADF docu-
ment hopper within five seconds after closing the ADF cover.
(5) LED status on error
If an error occurs during the test, the LED indicates as shown in table B.1.
If paper is jammed in the ADF, remove the jam and close the ADF cover. The CHECK
lamp stops blinking about three seconds after closing the ADF cover. To feed the docu-
ment from ADF, open and close the ADF cover.
Table B.1 LED at an error
Errors
Paper jam
POWER lamp
On
READ lamp
CHECK lamp
Blink
Off
Off
Off
On
On
Carrier unit error
Optical system error
Motor fuse failure
Lamp fuse failure
Blink
On
Blink
Blink
Blink
On
Blink
Blink
B – 2
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX C
C.1 Option
Name
IPC-2
Specification
CA01952-0191
Scanner
Feature
M3093EX
M3093GX
Image processing
• Automatic separation
• Image emphasis
• Outline extraction
• Mirror image
• Dynamic threshold
• Noise suppression
• Smoothing
CMP-2
CA
M3093GX
• 4 Mbyte memory
• MH/MR/MMR compression
Contact your Fujitsu sales agent for more information.
C.2 IPC-2/CMP-2 option board installation
WARNING: Follow the outlined procedure to avoid danger from electrical components.
(1) Verify that the scanner power is turned off.
(2) Remove the AC cable from the rear of the scanner.
(3) Romove the two screws securing the power supply and the interface PCA assembly.
(4) Pull the power supply and the PCA assembly out slightly and remove the flat cabel
connector. Then pull out the entire assembly.
CAUTION: Do not pull on the flat cable too strongly or it may be damaged.
Flat cable
(inside)
power supply and PCA assembly
screw
C – 1
Download from Www.Somanuals.com. All Manuals Search And Download.
(5) Remove the two screws in the following figure.
Two screws
(6) Remove the four screws from the interface connector and remove the two screws A in
the following figure.
Screw A
Interface connector screw
(7) Remove the cover from the interface PCA.
Cover
(8) Connect the IPC-2 option board connector and tighten the screw.
C – 2
Download from Www.Somanuals.com. All Manuals Search And Download.
(9) Where a CMP-2 is installed, remove the screw from the memory board and detach the
memory board. Connect the CMP-2 option board connector and tighten the screw.
IPC-2 option board
Screw for IPC-2
CMP-2 option board or memory PCA (M3093GX)
(not shown)
Screw for memor board or CMP-2 (M3093GX)
(10) Attach the power supply and PCA assembly in the reverse order of removal.
C – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is intentionally left blank.
C – 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Comments concerning this manual can be directed to one of the following addresses:
FUJITSU LIMITED
FUJITSU NORDIC AB
Kung Hans vag, S-191 76 Sollentuna, SWEDEN
TEL: 46-8-626-6000
International Operations
Marunouchi 1-6-1, Chiyoda-ku, Tokyo 100,
JAPAN
FAX: 46-8-626-6711
TEL: (81-3) 3216-3211
FAX: (81-3) 3213-7174
TLX: J22833
FUJITSU ITALIA S.p.A.
Via Melchiorre Gioia, No. 8-20124 Milano,
ITALY
Cable: “FUJITSU LIMITED TOKYO”
TEL: 39-2-63651
FAX: 39-2-6572257
FUJITSU COMPUTER PRODUCTS OF
AMERICA, INC.
2904 Orchard Parkway, San Jose.
California 95134-2022, U.S.A.
TEL: 1-408-432-6333
FUJITSU FRANCE S.A.
Batiment Aristote, 17 rue Olof palme
94006 Creteil cedex, FRANCE
TEL: 33-14-513-1616
FAX: 1-408-432-3908
FAX: 33-14-399-0700
FUJITSU CANADA, INC.
2800 Matheson Blvd. East, Mississauga.
Ontario 4X5, CANADA
TEL: 1-905-602-5454
FAX: 1-905-602-5457
FUJITSU AUSTRALIA LIMITED
475 Victoria Avenue Chatswood.
N.S.W 2067, AUSTRALIA
TEL: 61-2-410-4555
FAX: 61-2-411-8603
FUJITSU DEUTSCHLAND GmbH.
Frankfurter Ring 211,
8000 Munchen 40, F.R, GERMANY
TEL: 49-89-32378-0
FUJITSU HONG KONG Limited
Room 2521, Sum Hung Kai Centre
30 Harbour Road Wanchal, Hong Kong
TEL: 852-827-5780
FAX: 49-89-32378-100
FAX: 852-827-4724
TLX: 62667
FUJITSU EUROPE LTD.
2, Longwalk Road, Stockley Park, Uxbridge
Middlesex, UB11 1AB, U.K
TEL: 44-81-573-4444
FUJITSU ESPANA, S.A
Edificio torre Europa
FAX: 44-81-573-2643
TLX: 263871
Paseo de la Castellana 95 Madrid 28046, SPAIN
TEL: 34-1-581-8400
FAX: 34-1-581-8125
Download from Www.Somanuals.com. All Manuals Search And Download.
Reader Comment Form
We would appreciate your comments and suggestions for improving this publication.
Publication No. Rev. Letter Title Current Date
How did you use this publication?
Is the material presented effectively?
Learning
Reference
Installing
Maintaining
Sales
Operating
Fully
Covered
Well
illustrated
Well
Organized
Clean
What is your overall rating of this publication? What is your occupation?
Very Good Fair Very Poor
Good Poor
Your other comments may be entered here. Please be specific and
give page, paragraph and line number references where applicable.
Your Name & Return Address
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|